4gb products require an IOCB's FCP-LUN to be formatted in
wire-format prior to submission.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recent ISP24xx firmwares require that mailbox register 8 be
set to the maximum number of bytes to transfer during DMA
copying of the list. We safely set this value to zero
(infinite), since the call is *only* made in FCAL
topologies.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Commit 854165f424
inadvertently added some code meant only for testing -- the
driver was ignoring the non-zero function numbers of a
multi-port HBA.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fcport visibility is recognized during interrupt time, but,
rport removal can only occur during a process
(sleeping)-context. Return a DID_IMM_RETRY status for
commands submitted within this window to insure I/Os do not
prematurely run-out of retries.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Internal lun discovery has been removed since fc_transport
integration. Short-circuiting for tape-devices in
qla2x00_update_fcport() could inadvertently result in a
blocked rport timing-out and its targets being reaped.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT]. Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue. If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport. The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Given the semantic changes in both the device-model and
fc-transport APIs, the driver's handling of port-type RSCNs
via a series of ADISCs and PLOGIs can cause series of
badness ranging from unexpectedly device loss to devices not
being discovered.
In the interim, disable (via a module-parameter) this
feature and allow RSCN management to continue to occur
within the driver's DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similarly to other ISPs, set execution throttle to maximum
allowed value since 'throttling' is done on a per-lun basis
via queue-depth.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify essentially duplicate load RISC RAM implementation
in qla2x00_load_ram_ext() and qla2x00_load_ram().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Swing/emphasis settings in NVRAM were not being honoured due
to the driver not converting the serial-link options from LE
to host-endian format.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the Get Port Database call fails during local-loop
update, then schedule the DPC routine to perform a rescan as
the firmware would have updated the Get ID List port-entries
of their new state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Small changes to register retrieval and order as per latest
firmware specification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Driver would not correctly re-enable the write-protection
bits of the flash part after updates.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Problem report (against 2.4.x driver) from Jeff Layton
<jlayton@redhat.com>:
An OEM noticed that the U6 qla2200 driver would hang for
around 2 minutes at boot time and then proceed normally. I
found that the delay was occurring when loading the new
firmware into the card, and was due to a
schedule_timeout(10) added to the bottom of the polling
loop.
Some testing showed that the load ram operation on the card
was very quick (on the order of a couple of jiffies), but
the sleep in the polling loop was making each operation take
around 25-30.
The attached patch corrects this by making it skip sleeping
during the load ram operation, since I believe we only do
that when the module is plugged in. It also skips sleeping
if the mbox_int flag got set during the current loop.
This corrected the hang on my test setup, and OEM also
confirmed that it corrected the problem for them.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mailbox commands are polled for completion during ISP
initialization. During potentially 'long' mailbox commands
(i.e. fabric login), we really don't want a busy-wait delay
to potentially trigger a (benign) soft-lockup BUG().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no point in displaying the message during a valid
underrun case. Limit the message to potentially problematic
cases.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The initial-control-block references are not always correct
as the use-node-name qualifier during NVRAM configuration
will cause the firmware to use the portname as a base for
the nodename.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Adrian Bunk
Here's a composite patch with Adrian's original additions and
help-text with the new Kconfig variable SCSI_QLA_FC.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transition driver to exclusively use the request_firmware()
interfaces to retrieve firmware-blobs from user-space. This
will be the default behaviour going forward until the
embedded firmware-binary images are removed from the
upstream kernel.
Upon request, the driver caches the firmware image until the
driver is unloaded.
NOTE: The option is present to allow the user to continue to
use the firmware-loader modules, but, should be considered
deprecated.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Properly check FC_RESID for any non-transfered bytes
regardless of firmware completion status.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A regression in a recent change
33135aa2a5 caused the driver
to mistakenly drop handling of AENs. Due to the incorrect
handling, ports would not reappear after RSCNs and LIPs.
Drops unused/incorrect compound #define from qla_def.h.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated. A
similar delay was needed with earlier ISPs.
Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct issue where abort I/O command was not being issued
when the loop-state was down.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When mulitple initiators are coming up in an FCAL topology.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On MMIO relaxed-order platforms, it is possible for the
proper delay during NVRAM access to begin before the request
passes through the PCI bus (via a MMIO write) to the ISP.
Thus, causing a subsequent read to the NVRAM part to fail.
Add a MMIO read, after the MMIO write to insure any posted
writes are flushed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the drivers/scsi/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: 'Andrew Vasquez' <andrew.vasquez@qlogic.com>
Drop scsi_populate_tag_msg() interrogation.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The file is missing an include of scsi_transport_fc.h
drivers/scsi/qla2xxx/qla_rscn.c:334: error: implicit declaration of function 'fc_remote_port_unblock'
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here's a patch which drops the eh_active checks in the qla2xxx
eh_handler callbacks.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
andrew.vasquez@qlogic.com
James Bottomley
Ravi Anand
Jesper Juhl
James.Smart@Emulex.Com
James Bottomley