The value of IbsOpCurCnt rolls over when it reaches IbsOpMaxCnt. Thus,
it is reset to zero by hardware. To get the correct count we need to
add the max count to it in case we received an ibs sample (valid bit
set).
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-13-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After disabling IBS there could be still incomming NMIs with samples
that even have the valid bit cleared. Mark all this NMIs as handled to
avoid spurious interrupt messages.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-12-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When disabling ibs there might be the case where hardware continuously
generates interrupts. This is described in erratum #420 (Instruction-
Based Sampling Engine May Generate Interrupt that Cannot Be Cleared).
To avoid this we must clear the counter mask first and then clear the
enable bit. This patch implements this.
See Revision Guide for AMD Family 10h Processors, Publication #41322.
Note: We now keep track of the last read ibs config value which is
then used to disable ibs. To update the config value we pass now a
pointer to the functions reading it.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-11-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the last hw period is too short we might hit the irq handler which
biases the results. Thus try to have a max last period that triggers
the sw overflow.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-10-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are cases where the remaining period is smaller than the minimal
possible value. In this case the counter is restarted with the minimal
period. This is of no use as the interrupt handler will trigger
immediately again and most likely hits itself. This biases the
results.
So, if the remaining period is within the min range, we better do not
restart the counter and instead trigger the overflow.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-9-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds support for precise event sampling with IBS. There are
two counting modes to count either cycles or micro-ops. If the
corresponding performance counter events (hw events) are setup with
the precise flag set, the request is redirected to the ibs pmu:
perf record -a -e cpu-cycles:p ... # use ibs op counting cycle count
perf record -a -e r076:p ... # same as -e cpu-cycles:p
perf record -a -e r0C1:p ... # use ibs op counting micro-ops
Each ibs sample contains a linear address that points to the
instruction that was causing the sample to trigger. With ibs we have
skid 0. Thus, ibs supports precise levels 1 and 2. Samples are marked
with the PERF_EFLAGS_EXACT flag set. In rare cases the rip is invalid
when IBS was not able to record the rip correctly. Then the
PERF_EFLAGS_EXACT flag is cleared and the rip is taken from pt_regs.
V2:
* don't drop samples in precise level 2 if rip is invalid, instead
support the PERF_EFLAGS_EXACT flag
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120502103309.GP18810@erda.amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Each IBS sample contains a linear address of the instruction that
caused the sample to trigger. This address is more precise than the
rip that was taken from the interrupt handler's stack. Update the rip
with that address. We use this in the next patch to implement
precise-event sampling on AMD systems using IBS.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-6-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixing profiling at a fixed frequency, in this case the freq value and
sample period was setup incorrectly. Since sampling periods are
adjusted we also allow periods that have lower 4 bits set.
Another fix is the setup of the hw counter: If we modify
hwc->sample_period, we also need to update hwc->last_period and
hwc->period_left.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-5-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We always need to pass the last sample period to
perf_sample_data_init(), otherwise the event distribution will be
wrong. Thus, modifiyng the function interface with the required period
as argument. So basically a pattern like this:
perf_sample_data_init(&data, ~0ULL);
data.period = event->hw.last_period;
will now be like that:
perf_sample_data_init(&data, ~0ULL, event->hw.last_period);
Avoids unininitialized data.period and simplifies code.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-3-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The last sw period was not correctly updated on overflow and thus led
to wrong distribution of events. We always need to properly initialize
data.period in struct perf_sample_data.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333390758-10893-2-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Instead of only checking nonsensical topologies on numa-emu, do it
on real hardware as well, and print a warning.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/n/tip-re15l0jqjtpz709oxozt2zoh@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When using numa=fake= you can get weird topologies where LLCs can span
nodes and other such nonsense. Cure this by hard partitioning these
masks on node boundaries.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/n/tip-di5vwjm96q5vrb76opwuflwx@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
What was called show_registers() so far already showed a stack
trace for kernel faults, and kernel_stack_pointer() isn't even
valid to be used for faults from user mode, hence it was
pointless for show_regs() to call show_trace() after
show_registers().
Simply rename show_registers() to show_regs() and eliminate
the old definition.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/4FAA3D3902000078000826E1@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Added header for trampoline code that can be used to supply
input data to it. This makes interface between real mode code
and kernel cleaner and simpler. Replaced two confusing pointers
to level4 pgt in trampoline_64.S with a single pointer to the
beginning of the page table.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-21-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Simplified hierarchy under rm directory to a flat
directory because it is not anymore really justified
to have own directory for wakeup code. It only adds
more complexity.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-20-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There were number of issues in wakeup sequence:
- Wakeup stack was placed in hardcoded address.
- NX bit in EFER was not enabled.
- Initialization incorrectly set physical address
of secondary_startup_64.
- Some alignment issues.
This patch fixes these issues and in addition:
- Unifies coding conventions in .S files.
- Sets alignments of code and data right.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-18-git-send-email-jarkko.sakkinen@intel.com
Originally-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Set proper permissions for rodata, text and data, removing the
realmode trampoline area as a remaining RWX memory mapping in the
kernel.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-8-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Migrated ACPI wakeup code to the real-mode blob.
Code existing in .x86_trampoline can be completely
removed. Static descriptor table in wakeup_asm.S is
courtesy of H. Peter Anvin.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-7-git-send-email-jarkko.sakkinen@intel.com
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Migrated SMP trampoline code to the real mode blob.
SMP trampoline code is not yet removed from
.x86_trampoline because it is needed by the wakeup
code.
[ hpa: always enable compiling startup_32_smp in head_32.S... it is
only a few instructions which go into .init on UP builds, and it makes
the rest of the code less #ifdef ugly. ]
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-6-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Implements relocator for real mode code that is called
as part of setup_arch(). Processes segment relocations
and linear relocations. Real-mode code is relocated to
a free hole below 1 MB.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-4-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull two percpu fixes from Tejun Heo:
"One adds missing KERN_CONT on split printk()s and the other makes
the percpu allocator avoid using PMD_SIZE as atom_size on x86_32.
Using PMD_SIZE led to vmalloc area exhaustion on certain
configurations (x86_32 android) and the only cost of using PAGE_SIZE
instead is static percpu area not being aligned to large page
mapping."
* 'for-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu, x86: don't use PMD_SIZE as embedded atom_size on 32bit
percpu: use KERN_CONT in pcpu_dump_alloc_info()
With the embed percpu first chunk allocator, x86 uses either PAGE_SIZE
or PMD_SIZE for atom_size. PMD_SIZE is used when CPU supports PSE so
that percpu areas are aligned to PMD mappings and possibly allow using
PMD mappings in vmalloc areas in the future. Using larger atom_size
doesn't waste actual memory; however, it does require larger vmalloc
space allocation later on for !first chunks.
With reasonably sized vmalloc area, PMD_SIZE shouldn't be a problem
but x86_32 at this point is anything but reasonable in terms of
address space and using larger atom_size reportedly leads to frequent
percpu allocation failures on certain setups.
As there is no reason to not use PMD_SIZE on x86_64 as vmalloc space
is aplenty and most x86_64 configurations support PSE, fix the issue
by always using PMD_SIZE on x86_64 and PAGE_SIZE on x86_32.
v2: drop cpu_has_pse test and make x86_64 always use PMD_SIZE and
x86_32 PAGE_SIZE as suggested by hpa.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Yanmin Zhang <yanmin.zhang@intel.com>
Reported-by: ShuoX Liu <shuox.liu@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4F97BA98.6010001@intel.com>
Cc: stable@vger.kernel.org
The only difference is the free_thread_info function, which frees
xstate.
Use the new arch_release_task_struct() function instead and switch
over to the core allocator.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20120505150141.559556763@linutronix.de
Cc: x86@kernel.org
The local function io_apic_level_ack_pending() is only called
from io_apic_level_ack_pending(). The later function is only
compiled if CONFIG_GENERIC_PENDING_IRQ is defined. Move the
io_apic_level_ack_pending() to the existing #ifdef
CONFIG_GENERIC_PENDING_IRQ code block.
This will remove the following warning message during compiling
without CONFIG_GENERIC_PENDING_IRQ defined:
* arch/x86/kernel/apic/io_apic.c:382: warning: ‘io_apic_level_ack_pending’ defined but not used
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/1336461860.2296.3.camel@sbsiddha-mobl2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 31b3c9d723 ("xen/x86: Implement x86_apic_ops") implemented
this:
... without considering that on UP the function pointer might be NULL.
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/n/tip-3pfty0ml4yp62phbkchichh0@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The checks that exist in mwait_usable() for "idle=" kernel
parameters are insufficient. As a result, mwait_usable() can
return 1 even if "idle=nomwait" or "idle=poll" or "idle=halt"
parameters are passed.
Of these cases, incorrect handling of idle=nomwait is a
universal problem since mwait can get used for usual CPU idling.
However the rest of the cases are problematic only during CPU
Hotplug (offline) because, in the CPU offline path, the function
mwait_play_dead() is called, which might result in mwait being
used in the offline CPUs, if mwait_usable() happens to return 1.
Fix these issues by checking for the boot time "idle=" kernel
parameter properly in mwait_usable().
The first issue (usual cpu idling) is demonstrated below:
Before applying the patch (dmesg snippet):
[ 0.000000] Command line: [...] idle=nomwait
[ 0.000000] Kernel command line: [...] idle=nomwait
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.140606] using mwait in idle threads. <======= mwait being used
[ 4.303986] cpuidle: using governor ladder
[ 4.308232] cpuidle: using governor menu
After applying the patch:
[ 0.000000] Command line: [...] idle=nomwait
[ 0.000000] Kernel command line: [...] idle=nomwait
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 4.264100] cpuidle: using governor ladder
[ 4.268342] cpuidle: using governor menu
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: venki@google.com
Cc: suresh.b.siddha@intel.com
Cc: Borislav Petkov <bp@amd64.org>
Cc: lenb@kernel.org
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/4F9E37B8.30001@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On virtual environments, apic_read could take a long time. As a
result, under certain conditions the ack pending loop may exit
without any queued irqs left, but after more than one second. A
warning will be printed needlessly in this case.
If the loop is about to exit regardless of max_loops, don't
update it.
Signed-off-by: Shai Fultheim <shai@scalemp.com>
[ rebased and reworded the commit message]
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1334873552-31346-1-git-send-email-ido@wizery.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patchset introduces a generic ops-interface for
accessing interrupt remapping hardware on x86. It factors
out the VT-d specific code from io_apic.c and moves it to
drivers/iommu. These changes will be used to add support for
AMD interrupt remapping hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=H+Nt
-----END PGP SIGNATURE-----
Merge tag 'intr-remapping-ops-for-ingo' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu into core/iommu
- This patchset introduces a generic ops-interface for
accessing interrupt remapping hardware on x86. It factors
out the VT-d specific code from io_apic.c and moves it to
drivers/iommu. These changes will be used to add support for
AMD interrupt remapping hardware.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On some architectures (such as vSMP), it is possible to have
CPUs with a different number of cores sharing the same cache.
The current implementation implicitly assumes that all CPUs will
have the same number of cores sharing caches, and as a result,
different CPUs can end up with the same l2/l3 ids.
Fix this by masking out the shared cache bits, instead of
shifting the APICID. By doing so, it is guaranteed that the
generated cache ids are always unique.
Signed-off-by: Shai Fultheim <shai@scalemp.com>
[ rebased, simplified, and reworded the commit message]
Signed-off-by: Ido Yariv <ido@wizery.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Dave Jones <davej@redhat.com>
Link: http://lkml.kernel.org/r/1334873351-31142-1-git-send-email-ido@wizery.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is particularly to be able to specify "hpet=force,verbose",
as "force" ought to be a primary candidate for also wanting to
use "verbose".
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/4F79D120020000780007C031@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While Linux itself has been calling hpet_disable() for quite a
while, having e.g. a secondary (kexec) kernel depend on such
behavior of the primary (crashed) environment is fragile. It
particularly broke until very recently when the primary
environment was Xen based, as that hypervisor did not clear any
of the HPET settings it may have used.
Rather than blindly (and incompletely) clearing certain HPET
settings in hpet_disable(), latch the config register settings
during boot and restore then here.
(Note on the hpet_set_mode() change: Now that we're clearing the
level bit upon initialization, there's no need anymore to do so
here.)
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/4F79D0BB020000780007C02D@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Exit early when there's no support for a particular CPU family.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Jones <davej@redhat.com>
Cc: tigran@aivazian.fsnet.co.uk
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/4F8BDB58.6070007@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make the file names consistent with the naming conventions of irq subsystem.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Make the code consistent with the naming conventions of irq subsystem.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Remove the Intel specific interfaces from dmar.h and remove
asm/irq_remapping.h which is only used for io_apic.c anyway.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The operation for releasing a remapping entry is iommu
specific too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The function to set interrupt affinity with interrupt
remapping enabled is Intel specific too. So move it to the
irq_remap_ops too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The IOAPIC setup routine for interrupt remapping is VT-d
specific. Move it to the irq_remap_ops and add a call helper
function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Convert these calls too:
* Disable of remapping hardware
* Reenable of remapping hardware
* Enable fault handling
With that all of arch/x86/kernel/apic/apic.c is converted to
use the generic intr-remapping interface.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch introduces irq_remap_ops to hold implementation
specific function pointer to handle interrupt remapping. As
the first part the initialization functions for VT-d are
converted to these ops.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Commit ce7e5d2d19 ("x86: fix broken TASK_SIZE for ia32_aout") breaks
kernel builds when "CONFIG_IA32_AOUT=m" with
ERROR: "set_personality_ia32" [arch/x86/ia32/ia32_aout.ko] undefined!
make[1]: *** [__modpost] Error 1
The entry point needs to be exported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Al Viro <viro@zeniv.linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turned to be totally unneeded. The reason the code was introduced is
so that KVM can prefault swapped in page, but prefault can fail even
if mm is pinned since page table can change anyway. KVM handles this
situation correctly though and does not inject spurious page faults.
Fixes:
"INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected" warning while
running LTP inside a KVM guest using the recent -next kernel.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20120503085035.739963562@linutronix.de
Cc: x86@kernel.org
If CONFIG_KPROBES is not set, then linux/kprobes.h will not include
asm/kprobes.h needed by x86/ftrace.c for the BREAKPOINT macro.
The x86/ftrace.c file should just include asm/kprobes.h as it does not
need the rest of kprobes.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPnb50AAoJEHm+PkMAQRiGAE0H/A4zFZIUGmF3miKPDYmejmrZ
oVDYxVAu6JHjHWhu8E3VsinvyVscowjV8dr15eSaQzmDmRkSHAnUQ+dB7Di7jLC2
MNopxsWjwyZ8zvvr3rFR76kjbWKk/1GYytnf7GPZLbJQzd51om2V/TY/6qkwiDSX
U8Tt7ihSgHAezefqEmWp2X/1pxDCEt+VFyn9vWpkhgdfM1iuzF39MbxSZAgqDQ/9
JJrBHFXhArqJguhENwL7OdDzkYqkdzlGtS0xgeY7qio2CzSXxZXK4svT6FFGA8Za
xlAaIvzslDniv3vR2ZKd6wzUwFHuynX222hNim3QMaYdXm012M+Nn1ufKYGFxI0=
=4d4w
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc5' into next
Linux 3.4-rc5
Merge to pull in prerequisite change for Smack:
86812bb0de
Requested by Casey.
Which makes the code fit within the rest of the x86_ops functions.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
[v1: Changed x86_apic -> x86_ioapic per Yinghai Lu <yinghai@kernel.org> suggestion]
[v2: Rebased on tip/x86/urgent and redid to match Ingo's syntax style]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Turn off MC4_MISC thresholding banks on models which have them but that
particular processor implementation does not supply applicable error
sources to be counted.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Depending on whether the box supports the APIC LVT interrupt for
thresholding, we want to show the 'interrupt_enable' sysfs node or not.
Make that the case by adding it to the default sysfs attributes only if
it is supported.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Currently, the APIC LVT interrupt for error thresholding is implicitly
enabled. However, there are models in the F15h range which do not enable
it. Make the code machinery which sets up the APIC interrupt support
an optional setting and add an ->interrupt_capable member to the bank
representation mirroring that capability and enable the interrupt offset
programming only if it is true.
Simplify code and fixup comment style while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
As ftrace function tracing would require modifying code that could
be executed in NMI context, which is not stopped with stop_machine(),
ftrace had to do a complex algorithm with various stages of setup
and memory barriers to make it work.
With the new breakpoint method, this is no longer required. The changes
to the code can be done without any problem in NMI context, as well as
without stop machine altogether. Remove the complex code as it is
no longer needed.
Also, a lot of the notrace annotations could be removed from the
NMI code as it is now safe to trace them. With the exception of
do_nmi itself, which does some special work to handle running in
the debug stack. The breakpoint method can cause NMIs to double
nest the debug stack if it's not setup properly, and that is done
in do_nmi(), thus that function must not be traced.
(Note the arch sh may want to do the same)
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This method changes x86 to add a breakpoint to the mcount locations
instead of calling stop machine.
Now that iret can be handled by NMIs, we perform the following to
update code:
1) Add a breakpoint to all locations that will be modified
2) Sync all cores
3) Update all locations to be either a nop or call (except breakpoint
op)
4) Sync all cores
5) Remove the breakpoint with the new code.
6) Sync all cores
[
Added updates that Masami suggested:
Use unlikely(modifying_ftrace_code) in int3 trap to keep kprobes efficient.
Don't use NOTIFY_* in ftrace handler in int3 as it is not a notifier.
]
Cc: H. Peter Anvin <hpa@zytor.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
BIOS will switch off the corresponding feature flag on family
15h models 10h-1fh non-desktop CPUs.
The topology extension CPUID leafs are required to detect which
cores belong to the same compute unit. (thread siblings mask is
set accordingly and also correct information about L1i and L2
cache sharing depends on this).
W/o this patch we wouldn't see which cores belong to the same
compute unit and also cache sharing information for L1i and L2
would be incorrect on such systems.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now the return value of cmpxchg() is used to match an event. The
change removes the duplicate event comparison and traverses the list
until an event was removed. This also fixes the following warning:
arch/x86/kernel/cpu/perf_event_amd.c:170: warning: value computed is not used
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333643084-26776-3-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20120420124557.246929343@linutronix.de
Preparatory patch to use the generic idle thread allocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20120420124557.176604405@linutronix.de
A function name represents the pointer to it - no need to take the
address of it. (Fixing this helps us introduce some macro magic
around register_nmi_handler() in the future.)
Cc: Robert Richter <robert.richter@amd.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide systems that do not support x2apic cluster mode
a mechanism to select x2apic physical mode using the
FADT FORCE_APIC_PHYSICAL_DESTINATION_MODE bit.
Changes from v1: (based on Suresh's comments)
- removed #ifdef CONFIG_ACPI
- removed #include <linux/acpi.h>
Signed-off-by: Greg Pearson <greg.pearson@hp.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1335313436-32020-1-git-send-email-greg.pearson@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch tries to fix the problem of page fault exception
caused by accessing nmiaction structure in nmi if kmemcheck
is enabled.
If kmemcheck is enabled, the memory allocated through slab are
in pages that are marked non-present, so that some checks could
be done in the page fault handling code ( e.g. whether the
memory is read before written to ).
As nmiaction is allocated in this way, so it resides in a
non-present page. Then there is a page fault while the nmi code
accessing the nmiaction structure, which would then cause a
warning by WARN_ON_ONCE(in_nmi()) in kmemcheck_fault(), called
by do_page_fault().
This significantly simplifies the code as well, as the whole
dynamic allocation dance goes away.
v2: as Peter suggested, changed the nmiaction to use static
storage.
v3: as Peter suggested, use macro to shorten the codes. Also
keep the original usage of register_nmi_handler, so users of
this call doesn't need change.
Tested-by: Seiji Aguchi <seiji.aguchi@hds.com>
Fixes: https://lkml.org/lkml/2012/3/2/356
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
[ simplified the wrappers ]
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: thomas.mingarelli@hp.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1333051877-15755-4-git-send-email-dzickus@redhat.com
[ tidied the patch a bit ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In discussions with Thomas Mingarelli about hpwdt, he explained
to me some issues they were some when using their virtual NMI
button to test the hpwdt driver.
It turns out the virtual NMI button used on HP's machines do no
send unknown NMIs but instead send IO_CHK NMIs. The way the
kernel code is written, the hpwdt driver can not register itself
against that type of NMI and therefore can not successfully
capture system information before panic'ing.
To solve this I created two new NMI queues to allow driver to
register against the IO_CHK and SERR NMIs. Or in the hpwdt all
three (if you include unknown NMIs too).
The change is straightforward and just mimics what the unknown
NMI does.
Reported-and-tested-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1333051877-15755-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
way the code checks for already disabled indices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=VwUL
-----END PGP SIGNATURE-----
Merge tag 'l3-fix-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/urgent
A small L3 cache index disable fix from Srivatsa Bhat which unifies the
way the code checks for already disabled indices.
( Pulling it into v3.4 despite the v3.5 tag - the fix is small and we better
keep the same code across kernel versions for such user facing interfaces. )
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With commit a2ef5c4fd4
"ACPI: Move module parameter gts and bfs to sleep.c" the
wake_sleep_flags is required when calling acpi_enter_sleep_state.
The assembler code in wakeup_*.S did not do that. One solution
is to call it from assembler and stick the wake_sleep_flags on
the stack (for 32-bit) or in %esi (for 64-bit). hpa and rafael
both suggested however to create a wrapper function to call
acpi_enter_sleep_state and call said wrapper function
("acpi_enter_s3") from assembler.
For 32-bit, the acpi_enter_s3 ends up looking as so:
push %ebp
mov %esp,%ebp
sub $0x8,%esp
movzbl 0xc1809314,%eax [wake_sleep_flags]
movl $0x3,(%esp)
mov %eax,0x4(%esp)
call 0xc12d1fa0 <acpi_enter_sleep_state>
leave
ret
And 64-bit:
movzbl 0x9afde1(%rip),%esi [wake_sleep_flags]
push %rbp
mov $0x3,%edi
mov %rsp,%rbp
callq 0xffffffff812e9800 <acpi_enter_sleep_state>
leaveq
retq
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
[v2: Remove extra assembler operations, per hpa review]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-3-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
With commit a2ef5c4fd4
"ACPI: Move module parameter gts and bfs to sleep.c" the wake_sleep_flags
is required when calling acpi_enter_sleep_state, which means
that if there are functions outside the sleep.c code they
can't get the wake_sleep_flags values.
This converts the function in to a exported value and converts
the module config operands to a function.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Lin Ming <ming.m.lin@intel.com>
[v2: Parameters can be turned on/off dynamically]
[v3: unsigned char -> u8]
[v4: val -> kp->arg]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-2-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When GHES error record is logged into mcelog kernel buffer, a validation
check for physical address is necessary, which prevents reporting an
invalid physical address.
[Since physical address is the only useful element in this error record,
we drop generating the record completely if we don't have a valid address]
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove open-coded exception table entries in arch/x86/kernel/test_rodata.c,
and replace them with _ASM_EXTABLE() macros; this will allow us to
change the format and type of the exception table entries.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: David Daney <david.daney@cavium.com>
Link: http://lkml.kernel.org/r/CA%2B55aFyijf43qSu3N9nWHEBwaGbb7T2Oq9A=9EyR=Jtyqfq_cQ@mail.gmail.com
Remove open-coded exception table entries in arch/x86/kernel/entry_64.S,
and replace them with _ASM_EXTABLE() macros; this will allow us to
change the format and type of the exception table entries.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: David Daney <david.daney@cavium.com>
Link: http://lkml.kernel.org/r/CA%2B55aFyijf43qSu3N9nWHEBwaGbb7T2Oq9A=9EyR=Jtyqfq_cQ@mail.gmail.com
Remove open-coded exception table entries in arch/x86/kernel/entry_32.S,
and replace them with _ASM_EXTABLE() macros; this will allow us to
change the format and type of the exception table entries.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: David Daney <david.daney@cavium.com>
Link: http://lkml.kernel.org/r/CA%2B55aFyijf43qSu3N9nWHEBwaGbb7T2Oq9A=9EyR=Jtyqfq_cQ@mail.gmail.com
If we get an exception during early boot, walk the exception table to
see if we should intercept it. The main use case for this is to allow
rdmsr_safe()/wrmsr_safe() during CPU initialization.
Since the exception table is currently sorted at runtime, and fairly
late in startup, this code walks the exception table linearly. We
obviously don't need to worry about modules, however: none have been
loaded at this point.
This patch changes the early IDT setup to look a lot more like x86-64:
we now install handlers for all 32 exception vectors. The output of
the early exception handler has changed somewhat as it directly
reflects the stack frame of the exception handler, and the stack frame
has been somewhat restructured.
Finally, centralize the code that can and should be run only once.
[ v2: Use early_fixup_exception() instead of linear search ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1334794610-5546-6-git-send-email-hpa@zytor.com
If we get an exception during early boot, walk the exception table to
see if we should intercept it. The main use case for this is to allow
rdmsr_safe()/wrmsr_safe() during CPU initialization.
Since the exception table is currently sorted at runtime, and fairly
late in startup, this code walks the exception table linearly. We
obviously don't need to worry about modules, however: none have been
loaded at this point.
[ v2: Use early_fixup_exception() instead of linear search ]
Link: http://lkml.kernel.org/r/1334794610-5546-5-git-send-email-hpa@zytor.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
GET_CR2_INTO_RCX is asinine: it is only used in one place, the actual
paravirt call returns the value in %rax, not %rcx; and the one place
that wants it wants the result in %r9. We actually generate as a
result of this call:
call ...
movq %rax, %rcx
xorq %rax, %rax /* this value isn't even used... */
movq %rcx, %r9
At least make the macro do what the paravirt call does, which is put
the value into %rax.
Nevermind the fact that the macro clobbers all the volatile registers.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1334794610-5546-4-git-send-email-hpa@zytor.com
Cc: Glauber de Oliveira Costa <glommer@parallels.com>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
Documentation/feature-removal-schedule.txt
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If the L3 disable slot is already in use, return -EEXIST instead of
-EINVAL. The caller, store_cache_disable(), checks this return value to
print an appropriate warning.
Also, we want to signal with -EEXIST that the current index we're
disabling has actually been already disabled on the node:
$ echo 12 > /sys/devices/system/cpu/cpu3/cache/index3/cache_disable_0
$ echo 12 > /sys/devices/system/cpu/cpu3/cache/index3/cache_disable_0
-bash: echo: write error: File exists
$ echo 12 > /sys/devices/system/cpu/cpu3/cache/index3/cache_disable_1
-bash: echo: write error: File exists
$ echo 12 > /sys/devices/system/cpu/cpu5/cache/index3/cache_disable_1
-bash: echo: write error: File exists
The old code would say
-bash: echo: write error: Invalid argument
for disable slot 1 when playing the example above with no output in
dmesg, which is clearly misleading.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20120419070053.GB16645@elgon.mountain
[Boris: add testing for the other index too]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Reading machine check bank registers is slow. There is a trend of
increasing the number of banks, and the number of cores. The main section
of do_machine_check() is a serialized section where each cpu in turn
checks every bank. Even on a little two socket SandyBridge-EP system
that multiplies out as:
2 sockets * 8 cores * 2 hyperthreads * 20 banks = 640 MSRs
We already scan the banks in parallel in mce_no_way_out() to see if there
is a fatal error anywhere in the system. If we build a cache of VALID
bits during this scan, we can avoid uselessly re-reading banks that have
no data. Note that this cache is only a hint. If the valid bit is set in a
shared bank, all cpus that share that bank will see it during the parallel
scan, but the first to find it in the sequential scan will (usually) clear
the bank.
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Current APIC code assumes MSR_IA32_APICBASE is present for all systems.
Pentium Classic P5 and friends didn't have this MSR. MSR_IA32_APICBASE
was introduced as an architectural MSR by Intel @ P6.
Code paths that can touch this MSR invalidly are when vendor == Intel &&
cpu-family == 5 and APIC bit is set in CPUID - or when you simply pass
lapic on the kernel command line, on a P5.
The below patch stops Linux incorrectly interfering with the
MSR_IA32_APICBASE for P5 class machines. Other code paths exist that
touch the MSR - however those paths are not currently reachable for a
conformant P5.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linux.intel.com>
Link: http://lkml.kernel.org/r/4F8EEDD3.1080404@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Starting from 7e16838d "i387: support lazy restore of FPU state"
we assume that fpu_owner_task doesn't need restore_fpu_checking()
on the context switch, its FPU state should match what we already
have in the FPU on this CPU.
However, debugger can change the tracee's FPU state, in this case
we should reset fpu.last_cpu to ensure fpu_lazy_restore() can't
return true.
Change init_fpu() to do this, it is called by user_regset->set()
methods.
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20120416204815.GB24884@redhat.com
Cc: <stable@vger.kernel.org> v3.3
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It's only called from amd.c:srat_detect_node(). The introduced
condition for calling the fixup code is true for all AMD
multi-node processors, e.g. Magny-Cours and Interlagos. There we
have 2 NUMA nodes on one socket. Thus there are cores having
different numa-node-id but with equal phys_proc_id.
There is no point to print error messages in such a situation.
The confusing/misleading error message was introduced with
commit 64be4c1c24 ("x86: Add
x86_init platform override to fix up NUMA core numbering").
Remove the default fixup function (especially the error message)
and replace it by a NULL pointer check, move the
Numascale-specific condition for calling the fixup into the
fixup-function itself and slightly adapt the comment.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Cc: <sp@numascale.com>
Cc: <bp@amd64.org>
Cc: <daniel@numascale-asia.com>
Link: http://lkml.kernel.org/r/20120402160648.GR27684@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
microcode driver is loaded on unsupported platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZgVv
-----END PGP SIGNATURE-----
Merge tag 'microcode-fix-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/urgent
Pull from Borislav Petkov a two-patch fix from Andreas taking care of a sysfs
warning when the microcode driver is loaded on unsupported platforms.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge in latest upstream (and the latest perf development tree),
to prepare for tooling changes, and also to pick up v3.4 MM
changes that the uprobes code needs to take care of.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Enable support for seccomp filter on x86:
- syscall_get_arch()
- syscall_get_arguments()
- syscall_rollback()
- syscall_set_return_value()
- SIGSYS siginfo_t support
- secure_computing is called from a ptrace_event()-safe context
- secure_computing return value is checked (see below).
SECCOMP_RET_TRACE and SECCOMP_RET_TRAP may result in seccomp needing to
skip a system call without killing the process. This is done by
returning a non-zero (-1) value from secure_computing. This change
makes x86 respect that return value.
To ensure that minimal kernel code is exposed, a non-zero return value
results in an immediate return to user space (with an invalid syscall
number).
Signed-off-by: Will Drewry <wad@chromium.org>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
v18: rebase and tweaked change description, acked-by
v17: added reviewed by and rebased
v..: all rebases since original introduction.
Signed-off-by: James Morris <james.l.morris@oracle.com>
Exit early when there's no support for a particular CPU family. Also,
fixup the "no support for this CPU vendor" to be issued only when the
driver is attempted to be loaded on an unsupported vendor.
Cc: stable@vger.kernel.org
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: http://lkml.kernel.org/r/20120411163849.GE4794@alberich.amd.com
[Boris: add a commit msg because Andreas is lazy]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Pull x86 fixes from Thomas Gleixner.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Use correct byte-sized register constraint in __add()
x86: Use correct byte-sized register constraint in __xchg_op()
x86: vsyscall: Use NULL instead 0 for a pointer argument
check_and_clear_guest_paused does not need to be exported as it isn't used
by any modules, remove the export.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When a host stops or suspends a VM it will set a flag to show this. The
watchdog will use these functions to determine if a softlockup is real, or the
result of a suspended VM.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
asm-generic changes Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Pull a few KVM fixes from Avi Kivity:
"A bunch of powerpc KVM fixes, a guest and a host RCU fix (unrelated),
and a small build fix."
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Resolve RCU vs. async page fault problem
KVM: VMX: vmx_set_cr0 expects kvm->srcu locked
KVM: PMU: Fix integer constant is too large warning in kvm_pmu_set_msr()
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Page ready" async PF can kick vcpu out of idle state much like IRQ.
We need to tell RCU about this.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
3.4: Fix an an Smatch warning that appeared in the 3.4 merge window
3.0: Fix kgdb test suite with SMP for all archs without HW single stepping
2.6.36: Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
2.6.26: Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
Fix kgdb test suite with SMP for all archs with HW single stepping
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SW2N
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB regression fixes from Jason Wessel:
- Fix a Smatch warning that appeared in the 3.4 merge window
- Fix kgdb test suite with SMP for all archs without HW single stepping
- Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
- Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
- Fix kgdb test suite with SMP for all archs with HW single stepping
* tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
x86,kgdb: Fix DEBUG_RODATA limitation using text_poke()
kgdb,debug_core: pass the breakpoint struct instead of address and memory
kgdbts: (2 of 2) fix single step awareness to work correctly with SMP
kgdbts: (1 of 2) fix single step awareness to work correctly with SMP
kgdbts: Fix kernel oops with CONFIG_DEBUG_RODATA
kdb: Fix smatch warning on dbg_io_ops->is_console
Pull DMA mapping branch from Marek Szyprowski:
"Short summary for the whole series:
A few limitations have been identified in the current dma-mapping
design and its implementations for various architectures. There exist
more than one function for allocating and freeing the buffers:
currently these 3 are used dma_{alloc, free}_coherent,
dma_{alloc,free}_writecombine, dma_{alloc,free}_noncoherent.
For most of the systems these calls are almost equivalent and can be
interchanged. For others, especially the truly non-coherent ones
(like ARM), the difference can be easily noticed in overall driver
performance. Sadly not all architectures provide implementations for
all of them, so the drivers might need to be adapted and cannot be
easily shared between different architectures. The provided patches
unify all these functions and hide the differences under the already
existing dma attributes concept. The thread with more references is
available here:
http://www.spinics.net/lists/linux-sh/msg09777.html
These patches are also a prerequisite for unifying DMA-mapping
implementation on ARM architecture with the common one provided by
dma_map_ops structure and extending it with IOMMU support. More
information is available in the following thread:
http://thread.gmane.org/gmane.linux.kernel.cross-arch/12819
More works on dma-mapping framework are planned, especially in the
area of buffer sharing and managing the shared mappings (together with
the recently introduced dma_buf interface: commit d15bd7ee44
"dma-buf: Introduce dma buffer sharing mechanism").
The patches in the current set introduce a new alloc/free methods
(with support for memory attributes) in dma_map_ops structure, which
will later replace dma_alloc_coherent and dma_alloc_writecombine
functions."
People finally started piping up with support for merging this, so I'm
merging it as the last of the pending stuff from the merge window.
Looks like pohmelfs is going to wait for 3.5 and more external support
for merging.
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
common: DMA-mapping: add NON-CONSISTENT attribute
common: DMA-mapping: add WRITE_COMBINE attribute
common: dma-mapping: introduce mmap method
common: dma-mapping: remove old alloc_coherent and free_coherent methods
Hexagon: adapt for dma_map_ops changes
Unicore32: adapt for dma_map_ops changes
Microblaze: adapt for dma_map_ops changes
SH: adapt for dma_map_ops changes
Alpha: adapt for dma_map_ops changes
SPARC: adapt for dma_map_ops changes
PowerPC: adapt for dma_map_ops changes
MIPS: adapt for dma_map_ops changes
X86 & IA64: adapt for dma_map_ops changes
common: dma-mapping: introduce generic alloc() and free() methods
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: Call restore_sched_clock_state() only after %gs is initialized
x86: Use -mno-avx when available
x86: Remove the ancient and deprecated disable_hlt() and enable_hlt() facility
x86: Preserve lazy irq disable semantics in fixup_irqs()
Steven reported his P4 not booting properly, the missing format
attributes cause a NULL ptr deref. Cure this by adding the
missing format specification.
I took the format description out of the comment near
p4_config_pack*() and hope that comment is still relatively
accurate.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1332859842.16159.227.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf updates and fixes from Ingo Molnar:
"It's mostly fixes, but there's also two late items:
- preliminary GTK GUI support for perf report
- PMU raw event format descriptors in sysfs, to be parsed by tooling
The raw event format in sysfs is a new ABI. For example for the 'CPU'
PMU we have:
aldebaran:~> ll /sys/bus/event_source/devices/cpu/format/*
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/any
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/cmask
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/edge
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/event
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/inv
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/offcore_rsp
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/pc
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/umask
those lists of fields contain a specific format:
aldebaran:~> cat /sys/bus/event_source/devices/cpu/format/offcore_rsp
config1:0-63
So, those who wish to specify raw events can now use the following
event format:
-e cpu/cmask=1,event=2,umask=3
Most people will not want to specify any events (let alone raw
events), they'll just use whatever default event the tools use.
But for more obscure PMU events that have no cross-architecture
generic events the above syntax is more usable and a bit more
structured than specifying hex numbers."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
perf tools: Remove auto-generated bison/flex files
perf annotate: Fix off by one symbol hist size allocation and hit accounting
perf tools: Add missing ref-cycles event back to event parser
perf annotate: addr2line wants addresses in same format as objdump
perf probe: Finder fails to resolve function name to address
tracing: Fix ent_size in trace output
perf symbols: Handle NULL dso in dso__name_len
perf symbols: Do not include libgen.h
perf tools: Fix bug in raw sample parsing
perf tools: Fix display of first level of callchains
perf tools: Switch module.h into export.h
perf: Move mmap page data_head offset assertion out of header
perf: Fix mmap_page capabilities and docs
perf diff: Fix to work with new hists design
perf tools: Fix modifier to be applied on correct events
perf tools: Fix various casting issues for 32 bits
perf tools: Simplify event_read_id exit path
tracing: Fix ftrace stack trace entries
tracing: Move the tracing_on/off() declarations into CONFIG_TRACING
perf report: Add a simple GTK2-based 'perf report' browser
...
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
Conflicts:
drivers/acpi/acpica/hwsleep.c
Text conflict between:
2feec47d4c
(ACPICA: ACPI 5: Support for new FADT SleepStatus, SleepControl registers)
which removed #include "actables.h"
and
09f98a825a
(x86, acpi, tboot: Have a ACPI os prepare sleep instead of calling tboot_sleep.)
which removed #include <linux/tboot.h>
The resolution is to remove them both.
Signed-off-by: Len Brown <len.brown@intel.com>
When processor is being hot-added to the system, acpi_map_lsapic invokes
ACPI _MAT method to find APIC ID and flags, verifies that returned structure
is indeed ACPI's local APIC structure, and that flags contain MADT_ENABLED
bit. Then saves APIC ID, frees structure - and accesses structure when
computing arguments for acpi_register_lapic call. Which sometime leads
to acpi_register_lapic call being made with second argument zero, failing
to bring processor online with error 'Unable to map lapic to logical cpu
number'.
As lapic->lapic_flags & ACPI_MADT_ENABLED was already confirmed to be non-zero
few lines above, we can just pass unconditional ACPI_MADT_ENABLED to the
acpi_register_lapic.
Signed-off-by: Petr Vandrovec <petr@vmware.com>
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently when a CPU is off-lined it enters either MWAIT-based idle or,
if MWAIT is not desired or supported, HLT-based idle (which places the
processor in C1 state). This patch allows processors without MWAIT
support to stay in states deeper than C1.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The X86_32-only disable_hlt/enable_hlt mechanism was used by the
32-bit floppy driver. Its effect was to replace the use of the
HLT instruction inside default_idle() with cpu_relax() - essentially
it turned off the use of HLT.
This workaround was commented in the code as:
"disable hlt during certain critical i/o operations"
"This halt magic was a workaround for ancient floppy DMA
wreckage. It should be safe to remove."
H. Peter Anvin additionally adds:
"To the best of my knowledge, no-hlt only existed because of
flaky power distributions on 386/486 systems which were sold to
run DOS. Since DOS did no power management of any kind,
including HLT, the power draw was fairly uniform; when exposed
to the much hhigher noise levels you got when Linux used HLT
caused some of these systems to fail.
They were by far in the minority even back then."
Alan Cox further says:
"Also for the Cyrix 5510 which tended to go castors up if a HLT
occurred during a DMA cycle and on a few other boxes HLT during
DMA tended to go astray.
Do we care ? I doubt it. The 5510 was pretty obscure, the 5520
fixed it, the 5530 is probably the oldest still in any kind of
use."
So, let's finally drop this.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephen Hemminger <shemminger@vyatta.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/n/tip-3rhk9bzf0x9rljkv488tloib@git.kernel.org
[ If anyone cares then alternative instruction patching could be
used to replace HLT with a one-byte NOP instruction. Much simpler. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 cleanups from Peter Anvin:
"The biggest textual change is the cleanup to use symbolic constants
for x86 trap values.
The only *functional* change and the reason for the x86/x32 dependency
is the move of is_ia32_task() into <asm/thread_info.h> so that it can
be used in other code that needs to understand if a system call comes
from the compat entry point (and therefore uses i386 system call
numbers) or not. One intended user for that is the BPF system call
filter. Moving it out of <asm/compat.h> means we can define it
unconditionally, returning always true on i386."
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Move is_ia32_task to asm/thread_info.h from asm/compat.h
x86: Rename trap_no to trap_nr in thread_struct
x86: Use enum instead of literals for trap values
Pull x32 support for x86-64 from Ingo Molnar:
"This tree introduces the X32 binary format and execution mode for x86:
32-bit data space binaries using 64-bit instructions and 64-bit kernel
syscalls.
This allows applications whose working set fits into a 32 bits address
space to make use of 64-bit instructions while using a 32-bit address
space with shorter pointers, more compressed data structures, etc."
Fix up trivial context conflicts in arch/x86/{Kconfig,vdso/vma.c}
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
x32: Fix alignment fail in struct compat_siginfo
x32: Fix stupid ia32/x32 inversion in the siginfo format
x32: Add ptrace for x32
x32: Switch to a 64-bit clock_t
x32: Provide separate is_ia32_task() and is_x32_task() predicates
x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls
x86/x32: Fix the binutils auto-detect
x32: Warn and disable rather than error if binutils too old
x32: Only clear TIF_X32 flag once
x32: Make sure TS_COMPAT is cleared for x32 tasks
fs: Remove missed ->fds_bits from cessation use of fd_set structs internally
fs: Fix close_on_exec pointer in alloc_fdtable
x32: Drop non-__vdso weak symbols from the x32 VDSO
x32: Fix coding style violations in the x32 VDSO code
x32: Add x32 VDSO support
x32: Allow x32 to be configured
x32: If configured, add x32 system calls to system call tables
x32: Handle process creation
x32: Signal-related system calls
x86: Add #ifdef CONFIG_COMPAT to <asm/sys_ia32.h>
...
There has long been a limitation using software breakpoints with a
kernel compiled with CONFIG_DEBUG_RODATA going back to 2.6.26. For
this particular patch, it will apply cleanly and has been tested all
the way back to 2.6.36.
The kprobes code uses the text_poke() function which accommodates
writing a breakpoint into a read-only page. The x86 kgdb code can
solve the problem similarly by overriding the default breakpoint
set/remove routines and using text_poke() directly.
The x86 kgdb code will first attempt to use the traditional
probe_kernel_write(), and next try using a the text_poke() function.
The break point install method is tracked such that the correct break
point removal routine will get called later on.
Cc: x86@kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org # >= 2.6.36
Inspried-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull scheduler fixes from Ingo Molnar.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpusets: Remove an unused variable
sched/rt: Improve pick_next_highest_task_rt()
sched: Fix select_fallback_rq() vs cpu_active/cpu_online
sched/x86/smp: Do not enable IRQs over calibrate_delay()
sched: Fix compiler warning about declared inline after use
MAINTAINERS: Update email address for SCHEDULER and PERF EVENTS
Pull x86 updates from Ingo Molnar.
This touches some non-x86 files due to the sanitized INLINE_SPIN_UNLOCK
config usage.
Fixed up trivial conflicts due to just header include changes (removing
headers due to cpu_idle() merge clashing with the <asm/system.h> split).
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/amd: Be more verbose about LVT offset assignments
x86, tls: Off by one limit check
x86/ioapic: Add io_apic_ops driver layer to allow interception
x86/olpc: Add debugfs interface for EC commands
x86: Merge the x86_32 and x86_64 cpu_idle() functions
x86/kconfig: Remove CONFIG_TR=y from the defconfigs
x86: Stop recursive fault in print_context_stack after stack overflow
x86/io_apic: Move and reenable irq only when CONFIG_GENERIC_PENDING_IRQ=y
x86/apic: Add separate apic_id_valid() functions for selected apic drivers
locking/kconfig: Simplify INLINE_SPIN_UNLOCK usage
x86/kconfig: Update defconfigs
x86: Fix excessive MSR print out when show_msr is not specified
Pull timer core updates from Thomas Gleixner.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ia64: vsyscall: Add missing paranthesis
alarmtimer: Don't call rtc_timer_init() when CONFIG_RTC_CLASS=n
x86: vdso: Put declaration before code
x86-64: Inline vdso clock_gettime helpers
x86-64: Simplify and optimize vdso clock_gettime monotonic variants
kernel-time: fix s/then/than/ spelling errors
time: remove no_sync_cmos_clock
time: Avoid scary backtraces when warning of > 11% adj
alarmtimer: Make sure we initialize the rtctimer
ntp: Fix leap-second hrtimer livelock
x86, tsc: Skip refined tsc calibration on systems with reliable TSC
rtc: Provide flag for rtc devices that don't support UIE
ia64: vsyscall: Use seqcount instead of seqlock
x86: vdso: Use seqcount instead of seqlock
x86: vdso: Remove bogus locking in update_vsyscall_tz()
time: Remove bogus comments
time: Fix change_clocksource locking
time: x86: Fix race switching from vsyscall to non-vsyscall clock
The default irq_disable() sematics are to mark the interrupt disabled,
but keep it unmasked. If the interrupt is delivered while marked
disabled, the low level interrupt handler masks it and marks it
pending. This is important for detecting wakeup interrupts during
suspend and for edge type interrupts to avoid losing interrupts.
fixup_irqs() moves the interrupts away from an offlined cpu. For
certain interrupt types it needs to mask the interrupt line before
changing the affinity. After affinity has changed the interrupt line
is unmasked again, but only if it is not marked disabled.
This breaks the lazy irq disable semantics and causes problems in
suspend as the interrupt can be lost or wakeup functionality is
broken.
Check irqd_irq_masked() instead of irqd_irq_disabled() because
irqd_irq_masked() is only set, when the core code actually masked the
interrupt line. If it's not set, we unmask the interrupt and let the
lazy irq disable logic deal with an eventually incoming interrupt.
[ tglx: Massaged changelog and added a comment ]
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Link: http://lkml.kernel.org/r/27240C0AC20F114CBF8149A2696CBE4A05DFB3@SHSMSX101.ccr.corp.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge third batch of patches from Andrew Morton:
- Some MM stragglers
- core SMP library cleanups (on_each_cpu_mask)
- Some IPI optimisations
- kexec
- kdump
- IPMI
- the radix-tree iterator work
- various other misc bits.
"That'll do for -rc1. I still have ~10 patches for 3.4, will send
those along when they've baked a little more."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
backlight: fix typo in tosa_lcd.c
crc32: add help text for the algorithm select option
mm: move hugepage test examples to tools/testing/selftests/vm
mm: move slabinfo.c to tools/vm
mm: move page-types.c from Documentation to tools/vm
selftests/Makefile: make `run_tests' depend on `all'
selftests: launch individual selftests from the main Makefile
radix-tree: use iterators in find_get_pages* functions
radix-tree: rewrite gang lookup using iterator
radix-tree: introduce bit-optimized iterator
fs/proc/namespaces.c: prevent crash when ns_entries[] is empty
nbd: rename the nbd_device variable from lo to nbd
pidns: add reboot_pid_ns() to handle the reboot syscall
sysctl: use bitmap library functions
ipmi: use locks on watchdog timeout set on reboot
ipmi: simplify locking
ipmi: fix message handling during panics
ipmi: use a tasklet for handling received messages
ipmi: increase KCS timeouts
ipmi: decrease the IPMI message transaction time in interrupt mode
...
crashkernel reservation need know the total memory size. Current
get_total_mem simply use max_pfn - min_low_pfn. It is wrong because it
will including memory holes in the middle.
Especially for kvm guest with memory > 0xe0000000, there's below in qemu
code: qemu split memory as below:
if (ram_size >= 0xe0000000 ) {
above_4g_mem_size = ram_size - 0xe0000000;
below_4g_mem_size = 0xe0000000;
} else {
below_4g_mem_size = ram_size;
}
So for 4G mem guest, seabios will insert a 512M usable region beyond of
4G. Thus in above case max_pfn - min_low_pfn will be more than original
memsize.
Fixing this issue by using memblock_phys_mem_size() to get the total
memsize.
Signed-off-by: Dave Young <dyoung@redhat.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAT3NKzROxKuMESys7AQKElw/+JyDxJSlj+g+nymkx8IVVuU8CsEwNLgRk
8KEnRfLhGtkXFLSJYWO6jzGo16F8Uqli1PdMFte/wagSv0285/HZaKlkkBVHdJ/m
u40oSjgT013bBh6MQ0Oaf8pFezFUiQB5zPOA9QGaLVGDLXCmgqUgd7exaD5wRIwB
ZmyItjZeAVnDfk1R+ZiNYytHAi8A5wSB+eFDCIQYgyulA1Igd1UnRtx+dRKbvc/m
rWQ6KWbZHIdvP1ksd8wHHkrlUD2pEeJ8glJLsZUhMm/5oMf/8RmOCvmo8rvE/qwl
eDQ1h4cGYlfjobxXZMHqAN9m7Jg2bI946HZjdb7/7oCeO6VW3FwPZ/Ic75p+wp45
HXJTItufERYk6QxShiOKvA+QexnYwY0IT5oRP4DrhdVB/X9cl2MoaZHC+RbYLQy+
/5VNZKi38iK4F9AbFamS7kd0i5QszA/ZzEzKZ6VMuOp3W/fagpn4ZJT1LIA3m4A9
Q0cj24mqeyCfjysu0TMbPtaN+Yjeu1o1OFRvM8XffbZsp5bNzuTDEvviJ2NXw4vK
4qUHulhYSEWcu9YgAZXvEWDEM78FXCkg2v/CrZXH5tyc95kUkMPcgG+QZBB5wElR
FaOKpiC/BuNIGEf02IZQ4nfDxE90QwnDeoYeV+FvNj9UEOopJ5z5bMPoTHxm4cCD
NypQthI85pc=
=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Pull kvm updates from Avi Kivity:
"Changes include timekeeping improvements, support for assigning host
PCI devices that share interrupt lines, s390 user-controlled guests, a
large ppc update, and random fixes."
This is with the sign-off's fixed, hopefully next merge window we won't
have rebased commits.
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (130 commits)
KVM: Convert intx_mask_lock to spin lock
KVM: x86: fix kvm_write_tsc() TSC matching thinko
x86: kvmclock: abstract save/restore sched_clock_state
KVM: nVMX: Fix erroneous exception bitmap check
KVM: Ignore the writes to MSR_K7_HWCR(3)
KVM: MMU: make use of ->root_level in reset_rsvds_bits_mask
KVM: PMU: add proper support for fixed counter 2
KVM: PMU: Fix raw event check
KVM: PMU: warn when pin control is set in eventsel msr
KVM: VMX: Fix delayed load of shared MSRs
KVM: use correct tlbs dirty type in cmpxchg
KVM: Allow host IRQ sharing for assigned PCI 2.3 devices
KVM: Ensure all vcpus are consistent with in-kernel irqchip settings
KVM: x86 emulator: Allow PM/VM86 switch during task switch
KVM: SVM: Fix CPL updates
KVM: x86 emulator: VM86 segments must have DPL 3
KVM: x86 emulator: Fix task switch privilege checks
arch/powerpc/kvm/book3s_hv.c: included linux/sched.h twice
KVM: x86 emulator: correctly mask pmc index bits in RDPMC instruction emulation
KVM: mmu_notifier: Flush TLBs before releasing mmu_lock
...
Add information about LVT offset assignments to better debug firmware
bugs related to this. See following examples.
# dmesg | grep -i 'offset\|ibs'
LVT offset 0 assigned for vector 0xf9
[Firmware Bug]: cpu 0, try to use APIC500 (LVT offset 0) for vector 0x10400, but the register is already in use for vector 0xf9 on another cpu
[Firmware Bug]: cpu 0, IBS interrupt offset 0 not available (MSRC001103A=0x0000000000000100)
Failed to setup IBS, -22
In this case the BIOS assigns both offsets for MCE (0xf9) and IBS
(0x400) vectors to offset 0, which is why the second APIC setup (IBS)
failed.
With correct setup you get:
# dmesg | grep -i 'offset\|ibs'
LVT offset 0 assigned for vector 0xf9
LVT offset 1 assigned for vector 0x400
IBS: LVT offset 1 assigned
perf: AMD IBS detected (0x00000007)
oprofile: AMD IBS detected (0x00000007)
Note: The vector includes also the message type to handle also NMIs
(0x400). In the firmware bug message the format is the same as of the
APIC500 register and includes the mask bit (bit 16) in addition.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These are used as offsets into an array of GDT_ENTRY_TLS_ENTRIES members
so GDT_ENTRY_TLS_ENTRIES is one past the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://lkml.kernel.org/r/20120324075250.GA28258@elgon.mountain
Cc: <stable@vger.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Adapt core x86 and IA64 architecture code for dma_map_ops changes: replace
alloc/free_coherent with generic alloc/free methods.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
[removed swiotlb related changes and replaced it with wrappers,
merged with IA64 patch to avoid inter-patch dependences in intel-iommu code]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Xen dom0 needs to paravirtualize IO operations to the IO APIC,
so add a io_apic_ops for it to intercept. Do this as ops
structure because there's at least some chance that another
paravirtualized environment may want to intercept these.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: jwboyer@redhat.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/1332385090-18056-2-git-send-email-konrad.wilk@oracle.com
[ Made all the affected code easier on the eyes ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We should not ever enable IRQs until we're fully set up. This opens up
a window where interrupts can hit the cpu and interrupts can do
wakeups, wakeups need state that isn't set-up yet, in particular this
cpu isn't elegible to run tasks, so if any cpu-affine task that got
created in CPU_UP_PREPARE manages to get a wakeup, its affinity mask
will get broken and we'll run into lots of 'interesting' problems.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-yaezmlbriluh166tfkgni22m@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both functions are mostly identical.
The differences are:
- x86_32's cpu_idle() makes use of check_pgt_cache(), which is a
nop on both x86_32 and x86_64.
- x86_64's cpu_idle() uses enter/__exit_idle/(), on x86_32 these
function are a nop.
- In contrast to x86_32, x86_64 calls rcu_idle_enter/exit() in
the innermost loop because idle notifications need RCU.
Calling these function on x86_32 also in the innermost loop
does not hurt.
So we can merge both functions.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: paulmck@linux.vnet.ibm.com
Cc: josh@joshtriplett.org
Cc: tj@kernel.org
Link: http://lkml.kernel.org/r/1332709204-22496-1-git-send-email-richard@nod.at
Signed-off-by: Ingo Molnar <mingo@kernel.org>
"[RFC - PATCH 0/7] consolidation of BUG support code."
https://lkml.org/lkml/2012/1/26/525
--
The changes shown here are to unify linux's BUG support under
the one <linux/bug.h> file. Due to historical reasons, we have
some BUG code in bug.h and some in kernel.h -- i.e. the support for
BUILD_BUG in linux/kernel.h predates the addition of linux/bug.h,
but old code in kernel.h wasn't moved to bug.h at that time. As
a band-aid, kernel.h was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions.
Here is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.]
Ugh - very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and
hence relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2.
But to ensure that git history for bisect doesn't get needless
build failures introduced, the commits have been reorderd to fix
the problem areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PYQT
-----END PGP SIGNATURE-----
Merge tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/bug.h> cleanup from Paul Gortmaker:
"The changes shown here are to unify linux's BUG support under the one
<linux/bug.h> file. Due to historical reasons, we have some BUG code
in bug.h and some in kernel.h -- i.e. the support for BUILD_BUG in
linux/kernel.h predates the addition of linux/bug.h, but old code in
kernel.h wasn't moved to bug.h at that time. As a band-aid, kernel.h
was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions. Here
is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.] Ugh -
very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and hence
relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2. But
to ensure that git history for bisect doesn't get needless build
failures introduced, the commits have been reorderd to fix the problem
areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414"
Fix up conflicts (new radeon file, reiserfs header cleanups) as per Paul
and linux-next.
* tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
kernel.h: doesn't explicitly use bug.h, so don't include it.
bug: consolidate BUILD_BUG_ON with other bug code
BUG: headers with BUG/BUG_ON etc. need linux/bug.h
bug.h: add include of it to various implicit C users
lib: fix implicit users of kernel.h for TAINT_WARN
spinlock: macroize assert_spin_locked to avoid bug.h dependency
x86: relocate get/set debugreg fcns to include/asm/debugreg.
Sigh, warnings are there for a reason.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: John Stultz <john.stultz@linaro.org>
After printing out the first line of a stack backtrace,
print_context_stack() calls print_ftrace_graph_addr() to check
if it's making a graph of function calls, usually not the case.
But unfortunate ordering of assignments causes this to oops if
an earlier stack overflow corrupted threadinfo->task. Reorder
to avoid that irritation.
( The fact that there was a stack overflow may often be more
interesting than the stack that can now be shown; but
integrating that information with this stacktrace is awkward,
so leave it to overflow reporting. )
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120323225648.15DD5A033B@akpm.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull additional x86 fixes from Peter Anvin:
- address a long-standing bug related to when a kernel-spawned process
gets a signal on an i386 kernel compiled without CONFIG_VM86.
- fix the newly introduced build warning in arch/x86/boot.
- fix a typo in the i386 system call table which affects building some
libcs.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-32: Fix endless loop when processing signals for kernel tasks
x86, boot: Correct CFLAGS for hostprogs
x86-32: Fix typo for mq_getsetattr in syscall table
Merge second batch of patches from Andrew Morton:
- various misc things
- core kernel changes to prctl, exit, exec, init, etc.
- kernel/watchdog.c updates
- get_maintainer
- MAINTAINERS
- the backlight driver queue
- core bitops code cleanups
- the led driver queue
- some core prio_tree work
- checkpatch udpates
- largeish crc32 update
- a new poll() feature for the v4l guys
- the rtc driver queue
- fatfs
- ptrace
- signals
- kmod/usermodehelper updates
- coredump
- procfs updates
* emailed from Andrew Morton <akpm@linux-foundation.org>: (141 commits)
seq_file: add seq_set_overflow(), seq_overflow()
proc-ns: use d_set_d_op() API to set dentry ops in proc_ns_instantiate().
procfs: speed up /proc/pid/stat, statm
procfs: add num_to_str() to speed up /proc/stat
proc: speed up /proc/stat handling
fs/proc/kcore.c: make get_sparsemem_vmemmap_info() static
coredump: add VM_NODUMP, MADV_NODUMP, MADV_CLEAR_NODUMP
coredump: remove VM_ALWAYSDUMP flag
kmod: make __request_module() killable
kmod: introduce call_modprobe() helper
usermodehelper: ____call_usermodehelper() doesn't need do_exit()
usermodehelper: kill umh_wait, renumber UMH_* constants
usermodehelper: implement UMH_KILLABLE
usermodehelper: introduce umh_complete(sub_info)
usermodehelper: use UMH_WAIT_PROC consistently
signal: zap_pid_ns_processes: s/SEND_SIG_NOINFO/SEND_SIG_FORCED/
signal: oom_kill_task: use SEND_SIG_FORCED instead of force_sig()
signal: cosmetic, s/from_ancestor_ns/force/ in prepare_signal() paths
signal: give SEND_SIG_FORCED more power to beat SIGNAL_UNKILLABLE
Hexagon: use set_current_blocked() and block_sigmask()
...
Use for_each_clear_bit() to iterate over all the cleared bit in a
memory region.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This renames for_each_set_bit_cont() to for_each_set_bit_from() because
it is analogous to list_for_each_entry_from() in list.h rather than
list_for_each_entry_continue().
This doesn't remove for_each_set_bit_cont() for now.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to store the wall-to-monotonic offset and the realtime base.
It's faster to precompute the monotonic base.
This is about a 3% speedup on Sandy Bridge for CLOCK_MONOTONIC.
It's much more impressive for CLOCK_MONOTONIC_COARSE.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
- Fix KDB keyboard repeat scan codes and leaked keyboard events
- Fix kernel crash with kdb_printf() for users who compile new kdb_printf()'s
in early code
- Return all segment registers to gdb on x86_64
Features:
- KDB/KGDB hook the reboot notifier and end user can control if it stops,
detaches or does nothing (updated docs as well)
- Notify users who use CONFIG_DEBUG_RODATA to use hw breakpoints
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SXu9
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB updates from Jason Wessel:
"Fixes:
- Fix KDB keyboard repeat scan codes and leaked keyboard events
- Fix kernel crash with kdb_printf() for users who compile new
kdb_printf()'s in early code
- Return all segment registers to gdb on x86_64
Features:
- KDB/KGDB hook the reboot notifier and end user can control if it
stops, detaches or does nothing (updated docs as well)
- Notify users who use CONFIG_DEBUG_RODATA to use hw breakpoints"
* tag 'for_linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: Add message about CONFIG_DEBUG_RODATA on failure to install breakpoint
kdb: Avoid using dbg_io_ops until it is initialized
kgdb,debug_core: add the ability to control the reboot notifier
KDB: Fix usability issues relating to the 'enter' key.
kgdb,debug-core,gdbstub: Hook the reboot notifier for debugger detach
kgdb: Respect that flush op is optional
kgdb: x86: Return all segment registers also in 64-bit mode
This patch removes dead code from certain .config variations.
When CONFIG_GENERIC_PENDING_IRQ=n irq move and reenable code is
never get executed, nor do_unmask_irq variable updates its init
value. Move the code under CONFIG_GENERIC_PENDING_IRQ macro.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120320141935.GA24806@dhcp-26-207.brq.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As suggested by Suresh Siddha and Yinghai Lu:
For x2apic pre-enabled systems, apic driver is set already early
through early_acpi_boot_init()/early_acpi_process_madt()/
acpi_parse_madt()/default_acpi_madt_oem_check() path so that
apic_id_valid() checking will be sufficient during MADT and SRAT
parsing.
For non-x2apic pre-enabled systems, all apic ids should be less
than 255.
This allows us to substitute the checks in
arch/x86/kernel/acpi/boot.c::acpi_parse_x2apic() and
arch/x86/mm/srat.c::acpi_numa_x2apic_affinity_init() with
apic->apic_id_valid().
In addition we can avoid feigning the x2apic cpu feature in the
NumaChip apic code.
The following apic drivers have separate apic_id_valid()
functions which will accept x2apic type IDs :
x2apic_phys
x2apic_cluster
x2apic_uv_x
apic_numachip
Signed-off-by: Steffen Persvold <sp@numascale.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Daniel J Blueman <daniel@numascale-asia.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/1331925935-13372-1-git-send-email-sp@numascale.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave found:
| During bootup, I now have 162 messages like this..
| [ 0.227346] MSR0000001b: 00000000fee00900
| [ 0.227465] MSR00000021: 0000000000000001
| [ 0.227584] MSR0000002a: 00000000c1c81400
|
| commit 21c3fcf3e3 looks suspect.
| It claims that it will only print these out if show_msr= is
| passed, but that doesn't seem to be the case.
Fix it by changing to the version that checks the index.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1332477103-4595-1-git-send-email-yinghai@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Complete the syscall-less self-profiling feature and address
all complaints, namely:
- capabilities, so we can detect what is actually available at runtime
Add a capabilities field to perf_event_mmap_page to indicate
what is actually available for use.
- on x86: RDPMC weirdness due to being 40/48 bits and not sign-extending
properly.
- ABI documentation as to how all this stuff works.
Also improve the documentation for the new features.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vweaver1@eecs.utk.edu>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1332433596.2487.33.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
. Short term fix for 'diff' tool breakage related to perf.data files
with multiple events. From Jiri Olsa
. Cleanup for event id tracepoint reading routine, from Borislav Petkov
. 32-bit compilation fixes from Jiri Olsa
. Event parsing modifier assignment fixes from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=V7d9
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Cleanups and fixes for perf/core:
. Short term fix for 'diff' tool breakage related to perf.data files
with multiple events. From Jiri Olsa
. Cleanup for event id tracepoint reading routine, from Borislav Petkov
. 32-bit compilation fixes from Jiri Olsa
. Event parsing modifier assignment fixes from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The problem occurs on !CONFIG_VM86 kernels [1] when a kernel-mode task
returns from a system call with a pending signal.
A real-life scenario is a child of 'khelper' returning from a failed
kernel_execve() in ____call_usermodehelper() [ kernel/kmod.c ].
kernel_execve() fails due to a pending SIGKILL, which is the result of
"kill -9 -1" (at least, busybox's init does it upon reboot).
The loop is as follows:
* syscall_exit_work:
- work_pending: // start_of_the_loop
- work_notify_sig:
- do_notify_resume()
- do_signal()
- if (!user_mode(regs)) return;
- resume_userspace // TIF_SIGPENDING is still set
- work_pending // so we call work_pending => goto
// start_of_the_loop
More information can be found in another LKML thread:
http://www.serverphorums.com/read.php?12,457826
[1] the problem was also seen on MIPS.
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Link: http://lkml.kernel.org/r/1332448765.2299.68.camel@dimm
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Even if the content is always 0, gdb expects us to return also ds,
es, fs, and gs while in x86-64 mode. Do this to avoid ugly errors on
"info registers".
[jason.wessel@windriver.com: adjust NUMREGBYTES for two new regs]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull x86 "urgent" leftovers from Ingo Molnar:
"Pending x86/urgent bits that were not high prio enough to warrant
-rc-less v3.3-final inclusion."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Fix pointer math issue in handle_ramdisks()
x86/ioapic: Add register level checks to detect bogus io-apic entries
x86, mce: Fix rcu splat in drain_mce_log_buffer()
x86, memblock: Move mem_hole_size() to .init
Pull x86 platform changes from Ingo Molnar.
Removes the Moorestown platform that nobody ever used.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Move APIC ID validity check into platform APIC code
x86/olpc/xo15/sci: Enable lid close wakeup control
x86/geode/net5501: Add platform driver for Soekris Engineering net5501
x86/geode/alix2: Supplement driver to include GPIO button support
x86/mid/powerbtn: Use MSIC read/write instead of ipc_scu
x86/mid/thermal: Turn off thermistor
x86/mid/thermal: Add msic_thermal alias
x86/mid/thermal: Convert to use Intel MSIC API
x86/mid/scu_ipc: Remove Moorestown support
x86/mid: Kill off Moorestown
x86/mrst: Add msic_thermal platform support
x86/config: Select MSIC MFD driver on Intel Medfield platform
x86/mid: Remove Intel Moorestown
x86/mrst: Set ISA bus type for fake MP IRQs
x86/ioapic: Use legacy_pic to set correct gsi-irq mapping
Pull MCE changes from Ingo Molnar.
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix return value of mce_chrdev_read() when erst is disabled
x86/mce: Convert static array of pointers to per-cpu variables
x86/mce: Replace hard coded hex constants with symbolic defines
x86/mce: Recognise machine check bank signature for data path error
x86/mce: Handle "action required" errors
x86/mce: Add mechanism to safely save information in MCE handler
x86/mce: Create helper function to save addr/misc when needed
HWPOISON: Add code to handle "action required" errors.
HWPOISON: Clean up memory_failure() vs. __memory_failure()
Pull x86/fpu changes from Ingo Molnar.
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
i387: Split up <asm/i387.h> into exported and internal interfaces
i387: Uninline the generic FP helpers that we expose to kernel modules
Pull trivial x86 branches from Ingo Molnar: small one-liners to fix up
details.
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove some noise from boot log when starting cpus
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Fix port argument to inl() function
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Add CPU features from Intel document 319433-012A
* 'x86-process-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64: Record stack pointer before task execution begins
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/UV: Lower UV rtc clocksource rating
Pull x86/asm changes from Ingo Molnar
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Include probe_roms.h in probe_roms.c
x86/32: Print control and debug registers for kerenel context
x86: Tighten dependencies of CPU_SUP_*_32
x86/numa: Improve internode cache alignment
x86: Fix the NMI nesting comments
x86-64: Improve insn scheduling in SAVE_ARGS_IRQ
x86-64: Fix CFI annotations for NMI nesting code
bitops: Add missing parentheses to new get_order macro
bitops: Optimise get_order()
bitops: Adjust the comment on get_order() to describe the size==0 case
x86/spinlocks: Eliminate TICKET_MASK
x86-64: Handle byte-wise tail copying in memcpy() without a loop
x86-64: Fix memcpy() to support sizes of 4Gb and above
x86-64: Fix memset() to support sizes of 4Gb and above
x86-64: Slightly shorten copy_page()
If the required size is bigger than cached_hole_size it is better to
search from free_area_cache - it is easier to get a free region,
specifically for the 64 bit process whose address space is large enough
Do it just as hugetlb_get_unmapped_area_topdown() in arch/x86/mm/hugetlbpage.c
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases it may happen that pmd_none_or_clear_bad() is called with
the mmap_sem hold in read mode. In those cases the huge page faults can
allocate hugepmds under pmd_none_or_clear_bad() and that can trigger a
false positive from pmd_bad() that will not like to see a pmd
materializing as trans huge.
It's not khugepaged causing the problem, khugepaged holds the mmap_sem
in write mode (and all those sites must hold the mmap_sem in read mode
to prevent pagetables to go away from under them, during code review it
seems vm86 mode on 32bit kernels requires that too unless it's
restricted to 1 thread per process or UP builds). The race is only with
the huge pagefaults that can convert a pmd_none() into a
pmd_trans_huge().
Effectively all these pmd_none_or_clear_bad() sites running with
mmap_sem in read mode are somewhat speculative with the page faults, and
the result is always undefined when they run simultaneously. This is
probably why it wasn't common to run into this. For example if the
madvise(MADV_DONTNEED) runs zap_page_range() shortly before the page
fault, the hugepage will not be zapped, if the page fault runs first it
will be zapped.
Altering pmd_bad() not to error out if it finds hugepmds won't be enough
to fix this, because zap_pmd_range would then proceed to call
zap_pte_range (which would be incorrect if the pmd become a
pmd_trans_huge()).
The simplest way to fix this is to read the pmd in the local stack
(regardless of what we read, no need of actual CPU barriers, only
compiler barrier needed), and be sure it is not changing under the code
that computes its value. Even if the real pmd is changing under the
value we hold on the stack, we don't care. If we actually end up in
zap_pte_range it means the pmd was not none already and it was not huge,
and it can't become huge from under us (khugepaged locking explained
above).
All we need is to enforce that there is no way anymore that in a code
path like below, pmd_trans_huge can be false, but pmd_none_or_clear_bad
can run into a hugepmd. The overhead of a barrier() is just a compiler
tweak and should not be measurable (I only added it for THP builds). I
don't exclude different compiler versions may have prevented the race
too by caching the value of *pmd on the stack (that hasn't been
verified, but it wouldn't be impossible considering
pmd_none_or_clear_bad, pmd_bad, pmd_trans_huge, pmd_none are all inlines
and there's no external function called in between pmd_trans_huge and
pmd_none_or_clear_bad).
if (pmd_trans_huge(*pmd)) {
if (next-addr != HPAGE_PMD_SIZE) {
VM_BUG_ON(!rwsem_is_locked(&tlb->mm->mmap_sem));
split_huge_page_pmd(vma->vm_mm, pmd);
} else if (zap_huge_pmd(tlb, vma, pmd, addr))
continue;
/* fall through */
}
if (pmd_none_or_clear_bad(pmd))
Because this race condition could be exercised without special
privileges this was reported in CVE-2012-1179.
The race was identified and fully explained by Ulrich who debugged it.
I'm quoting his accurate explanation below, for reference.
====== start quote =======
mapcount 0 page_mapcount 1
kernel BUG at mm/huge_memory.c:1384!
At some point prior to the panic, a "bad pmd ..." message similar to the
following is logged on the console:
mm/memory.c:145: bad pmd ffff8800376e1f98(80000000314000e7).
The "bad pmd ..." message is logged by pmd_clear_bad() before it clears
the page's PMD table entry.
143 void pmd_clear_bad(pmd_t *pmd)
144 {
-> 145 pmd_ERROR(*pmd);
146 pmd_clear(pmd);
147 }
After the PMD table entry has been cleared, there is an inconsistency
between the actual number of PMD table entries that are mapping the page
and the page's map count (_mapcount field in struct page). When the page
is subsequently reclaimed, __split_huge_page() detects this inconsistency.
1381 if (mapcount != page_mapcount(page))
1382 printk(KERN_ERR "mapcount %d page_mapcount %d\n",
1383 mapcount, page_mapcount(page));
-> 1384 BUG_ON(mapcount != page_mapcount(page));
The root cause of the problem is a race of two threads in a multithreaded
process. Thread B incurs a page fault on a virtual address that has never
been accessed (PMD entry is zero) while Thread A is executing an madvise()
system call on a virtual address within the same 2 MB (huge page) range.
virtual address space
.---------------------.
| |
| |
.-|---------------------|
| | |
| | |<-- B(fault)
| | |
2 MB | |/////////////////////|-.
huge < |/////////////////////| > A(range)
page | |/////////////////////|-'
| | |
| | |
'-|---------------------|
| |
| |
'---------------------'
- Thread A is executing an madvise(..., MADV_DONTNEED) system call
on the virtual address range "A(range)" shown in the picture.
sys_madvise
// Acquire the semaphore in shared mode.
down_read(¤t->mm->mmap_sem)
...
madvise_vma
switch (behavior)
case MADV_DONTNEED:
madvise_dontneed
zap_page_range
unmap_vmas
unmap_page_range
zap_pud_range
zap_pmd_range
//
// Assume that this huge page has never been accessed.
// I.e. content of the PMD entry is zero (not mapped).
//
if (pmd_trans_huge(*pmd)) {
// We don't get here due to the above assumption.
}
//
// Assume that Thread B incurred a page fault and
.---------> // sneaks in here as shown below.
| //
| if (pmd_none_or_clear_bad(pmd))
| {
| if (unlikely(pmd_bad(*pmd)))
| pmd_clear_bad
| {
| pmd_ERROR
| // Log "bad pmd ..." message here.
| pmd_clear
| // Clear the page's PMD entry.
| // Thread B incremented the map count
| // in page_add_new_anon_rmap(), but
| // now the page is no longer mapped
| // by a PMD entry (-> inconsistency).
| }
| }
|
v
- Thread B is handling a page fault on virtual address "B(fault)" shown
in the picture.
...
do_page_fault
__do_page_fault
// Acquire the semaphore in shared mode.
down_read_trylock(&mm->mmap_sem)
...
handle_mm_fault
if (pmd_none(*pmd) && transparent_hugepage_enabled(vma))
// We get here due to the above assumption (PMD entry is zero).
do_huge_pmd_anonymous_page
alloc_hugepage_vma
// Allocate a new transparent huge page here.
...
__do_huge_pmd_anonymous_page
...
spin_lock(&mm->page_table_lock)
...
page_add_new_anon_rmap
// Here we increment the page's map count (starts at -1).
atomic_set(&page->_mapcount, 0)
set_pmd_at
// Here we set the page's PMD entry which will be cleared
// when Thread A calls pmd_clear_bad().
...
spin_unlock(&mm->page_table_lock)
The mmap_sem does not prevent the race because both threads are acquiring
it in shared mode (down_read). Thread B holds the page_table_lock while
the page's map count and PMD table entry are updated. However, Thread A
does not synchronize on that lock.
====== end quote =======
[akpm@linux-foundation.org: checkpatch fixes]
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Jones <davej@redhat.com>
Acked-by: Larry Woodman <lwoodman@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org> [2.6.38+]
Cc: Mark Salter <msalter@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ruGA
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irq_domain support for all architectures from Grant Likely:
"Generialize powerpc's irq_host as irq_domain
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
dt: fix twl4030 for non-dt compile on x86
mfd: twl-core: Add IRQ_DOMAIN dependency
devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
irq_domain: Centralize definition of irq_dispose_mapping()
irq_domain/mips: Allow irq_domain on MIPS
irq_domain/x86: Convert x86 (embedded) to use common irq_domain
ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
irq_domain/microblaze: Convert microblaze to use irq_domains
irq_domain/powerpc: Replace custom xlate functions with library functions
irq_domain/powerpc: constify irq_domain_ops
irq_domain/c6x: Use library of xlate functions
irq_domain/c6x: constify irq_domain structures
irq_domain/c6x: Convert c6x to use generic irq_domain support.
irq_domain: constify irq_domain_ops
irq_domain: Create common xlate functions that device drivers can use
irq_domain: Remove irq_domain_add_simple()
irq_domain: Remove 'new' irq_domain in favour of the ppc one
mfd: twl-core.c: Fix the number of interrupts managed by twl4030
of/address: add empty static inlines for !CONFIG_OF
irq_domain: Add support for base irq and hwirq in legacy mappings
...
Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=IGhc
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates for 3.4 from Rafael Wysocki:
"Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes."
* tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (43 commits)
PM / Domains: Check domain status during hibernation restore of devices
PM / devfreq: add relation of recommended frequency.
PM / shmobile: Make MTU2 driver use pm_genpd_dev_always_on()
PM / shmobile: Make CMT driver use pm_genpd_dev_always_on()
PM / shmobile: Make TMU driver use pm_genpd_dev_always_on()
PM / Domains: Introduce "always on" device flag
PM / Domains: Fix hibernation restore of devices, v2
PM / Domains: Fix handling of wakeup devices during system resume
sh_mmcif / PM: Use PM QoS latency constraint
tmio_mmc / PM: Use PM QoS latency constraint
PM / QoS: Make it possible to expose PM QoS latency constraints
PM / Sleep: JBD and JBD2 missing set_freezable()
PM / Domains: Fix include for PM_GENERIC_DOMAINS=n case
PM / Freezer: Remove references to TIF_FREEZE in comments
PM / Sleep: Add more wakeup source initialization routines
PM / Hibernate: Enable usermodehelpers in hibernate() error path
PM / Sleep: Make __pm_stay_awake() delete wakeup source timers
PM / Sleep: Fix race conditions related to wakeup source timer function
PM / Sleep: Fix possible infinite loop during wakeup source destruction
PM / Hibernate: print physical addresses consistently with other parts of kernel
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink breakage
reverted), dynamic debugging updates, w1 drivers, hyperv driver updates,
and a variety of other bits and pieces, full information in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9neCsACgkQMUfUDdst+ylyQwCfY2eizvzw5HhjQs8gOiBRDADe
yrgAnj1Zan2QkoCnQIFJNAoxqNX9yAhd
=biH6
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches for 3.4-rc1 from Greg KH:
"Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink
breakage reverted), dynamic debugging updates, w1 drivers, hyperv
driver updates, and a variety of other bits and pieces, full
information in the shortlog."
* tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (78 commits)
Tools: hv: Support enumeration from all the pools
Tools: hv: Fully support the new KVP verbs in the user level daemon
Drivers: hv: Support the newly introduced KVP messages in the driver
Drivers: hv: Add new message types to enhance KVP
regulator: Support driver probe deferral
Revert "sysfs: Kill nlink counting."
uevent: send events in correct order according to seqnum (v3)
driver core: minor comment formatting cleanups
driver core: move the deferred probe pointer into the private area
drivercore: Add driver probe deferral mechanism
DS2781 Maxim Stand-Alone Fuel Gauge battery and w1 slave drivers
w1_bq27000: Only one thread can access the bq27000 at a time.
w1_bq27000 - remove w1_bq27000_write
w1_bq27000: remove unnecessary NULL test.
sysfs: Fix memory leak in sysfs_sd_setsecdata().
intel_idle: Revert change of auto_demotion_disable_flags for Nehalem
w1: Fix w1_bq27000
driver-core: documentation: fix up Greg's email address
powernow-k6: Really enable auto-loading
powernow-k7: Fix CPU family number
...
Pull timer changes for v3.4 from Ingo Molnar
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
ntp: Fix integer overflow when setting time
math: Introduce div64_long
cs5535-clockevt: Allow the MFGPT IRQ to be shared
cs5535-clockevt: Don't ignore MFGPT on SMP-capable kernels
x86/time: Eliminate unused irq0_irqs counter
clocksource: scx200_hrt: Fix the build
x86/tsc: Reduce the TSC sync check time for core-siblings
timer: Fix bad idle check on irq entry
nohz: Remove ts->Einidle checks before restarting the tick
nohz: Remove update_ts_time_stat from tick_nohz_start_idle
clockevents: Leave the broadcast device in shutdown mode when not needed
clocksource: Load the ACPI PM clocksource asynchronously
clocksource: scx200_hrt: Convert scx200 to use clocksource_register_hz
clocksource: Get rid of clocksource_calc_mult_shift()
clocksource: dbx500: convert to clocksource_register_hz()
clocksource: scx200_hrt: use pr_<level> instead of printk
time: Move common updates to a function
time: Reorder so the hot data is together
time: Remove most of xtime_lock usage in timekeeping.c
ntp: Add ntp_lock to replace xtime_locking
...
Pull scheduler changes for v3.4 from Ingo Molnar
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
printk: Make it compile with !CONFIG_PRINTK
sched/x86: Fix overflow in cyc2ns_offset
sched: Fix nohz load accounting -- again!
sched: Update yield() docs
printk/sched: Introduce special printk_sched() for those awkward moments
sched/nohz: Correctly initialize 'next_balance' in 'nohz' idle balancer
sched: Cleanup cpu_active madness
sched: Fix load-balance wreckage
sched: Clean up parameter passing of proc_sched_autogroup_set_nice()
sched: Ditch per cgroup task lists for load-balancing
sched: Rename load-balancing fields
sched: Move load-balancing arguments into helper struct
sched/rt: Do not submit new work when PI-blocked
sched/rt: Prevent idle task boosting
sched/wait: Add __wake_up_all_locked() API
sched/rt: Document scheduler related skip-resched-check sites
sched/rt: Use schedule_preempt_disabled()
sched/rt: Add schedule_preempt_disabled()
sched/rt: Do not throttle when PI boosting
sched/rt: Keep period timer ticking when rt throttling is active
...
Pull perf events changes for v3.4 from Ingo Molnar:
- New "hardware based branch profiling" feature both on the kernel and
the tooling side, on CPUs that support it. (modern x86 Intel CPUs
with the 'LBR' hardware feature currently.)
This new feature is basically a sophisticated 'magnifying glass' for
branch execution - something that is pretty difficult to extract from
regular, function histogram centric profiles.
The simplest mode is activated via 'perf record -b', and the result
looks like this in perf report:
$ perf record -b any_call,u -e cycles:u branchy
$ perf report -b --sort=symbol
52.34% [.] main [.] f1
24.04% [.] f1 [.] f3
23.60% [.] f1 [.] f2
0.01% [k] _IO_new_file_xsputn [k] _IO_file_overflow
0.01% [k] _IO_vfprintf_internal [k] _IO_new_file_xsputn
0.01% [k] _IO_vfprintf_internal [k] strchrnul
0.01% [k] __printf [k] _IO_vfprintf_internal
0.01% [k] main [k] __printf
This output shows from/to branch columns and shows the highest
percentage (from,to) jump combinations - i.e. the most likely taken
branches in the system. "branches" can also include function calls
and any other synchronous and asynchronous transitions of the
instruction pointer that are not 'next instruction' - such as system
calls, traps, interrupts, etc.
This feature comes with (hopefully intuitive) flat ascii and TUI
support in perf report.
- Various 'perf annotate' visual improvements for us assembly junkies.
It will now recognize function calls in the TUI and by hitting enter
you can follow the call (recursively) and back, amongst other
improvements.
- Multiple threads/processes recording support in perf record, perf
stat, perf top - which is activated via a comma-list of PIDs:
perf top -p 21483,21485
perf stat -p 21483,21485 -ddd
perf record -p 21483,21485
- Support for per UID views, via the --uid paramter to perf top, perf
report, etc. For example 'perf top --uid mingo' will only show the
tasks that I am running, excluding other users, root, etc.
- Jump label restructurings and improvements - this includes the
factoring out of the (hopefully much clearer) include/linux/static_key.h
generic facility:
struct static_key key = STATIC_KEY_INIT_FALSE;
...
if (static_key_false(&key))
do unlikely code
else
do likely code
...
static_key_slow_inc();
...
static_key_slow_inc();
...
The static_key_false() branch will be generated into the code with as
little impact to the likely code path as possible. the
static_key_slow_*() APIs flip the branch via live kernel code patching.
This facility can now be used more widely within the kernel to
micro-optimize hot branches whose likelihood matches the static-key
usage and fast/slow cost patterns.
- SW function tracer improvements: perf support and filtering support.
- Various hardenings of the perf.data ABI, to make older perf.data's
smoother on newer tool versions, to make new features integrate more
smoothly, to support cross-endian recording/analyzing workflows
better, etc.
- Restructuring of the kprobes code, the splitting out of 'optprobes',
and a corner case bugfix.
- Allow the tracing of kernel console output (printk).
- Improvements/fixes to user-space RDPMC support, allowing user-space
self-profiling code to extract PMU counts without performing any
system calls, while playing nice with the kernel side.
- 'perf bench' improvements
- ... and lots of internal restructurings, cleanups and fixes that made
these features possible. And, as usual this list is incomplete as
there were also lots of other improvements
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (120 commits)
perf report: Fix annotate double quit issue in branch view mode
perf report: Remove duplicate annotate choice in branch view mode
perf/x86: Prettify pmu config literals
perf report: Enable TUI in branch view mode
perf report: Auto-detect branch stack sampling mode
perf record: Add HEADER_BRANCH_STACK tag
perf record: Provide default branch stack sampling mode option
perf tools: Make perf able to read files from older ABIs
perf tools: Fix ABI compatibility bug in print_event_desc()
perf tools: Enable reading of perf.data files from different ABI rev
perf: Add ABI reference sizes
perf report: Add support for taken branch sampling
perf record: Add support for sampling taken branch
perf tools: Add code to support PERF_SAMPLE_BRANCH_STACK
x86/kprobes: Split out optprobe related code to kprobes-opt.c
x86/kprobes: Fix a bug which can modify kernel code permanently
x86/kprobes: Fix instruction recovery on optimized path
perf: Add callback to flush branch_stack on context switch
perf: Disable PERF_SAMPLE_BRANCH_* when not supported
perf/x86: Add LBR software filter support for Intel CPUs
...
Pull irq/core changes for v3.4 from Ingo Molnar
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Remove paranoid warnons and bogus fixups
genirq: Flush the irq thread on synchronization
genirq: Get rid of unnecessary IRQTF_DIED flag
genirq: No need to check IRQTF_DIED before stopping a thread handler
genirq: Get rid of unnecessary irqaction field in task_struct
genirq: Fix incorrect check for forced IRQ thread handler
softirq: Reduce invoke_softirq() code duplication
genirq: Fix long-term regression in genirq irq_set_irq_type() handling
x86-32/irq: Don't switch to irq stack for a user-mode irq
Upon resume from hibernation, CPU 0's hvclock area contains the old
values for system_time and tsc_timestamp. It is necessary for the
hypervisor to update these values with uptodate ones before the CPU uses
them.
Abstract TSC's save/restore sched_clock_state functions and use
restore_state to write to KVM_SYSTEM_TIME MSR, forcing an update.
Also move restore_sched_clock_state before __restore_processor_state,
since the later calls CONFIG_LOCK_STAT's lockstat_clock (also for TSC).
Thanks to Igor Mammedov for tracking it down.
Fixes suspend-to-disk with kvmclock.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix the following section warnings :
WARNING: vmlinux.o(.text+0x49dbc): Section mismatch in reference
from the function acpi_map_cpu2node() to the variable
.cpuinit.data:__apicid_to_node The function acpi_map_cpu2node()
references the variable __cpuinitdata __apicid_to_node. This is
often because acpi_map_cpu2node lacks a __cpuinitdata
annotation or the annotation of __apicid_to_node is wrong.
WARNING: vmlinux.o(.text+0x49dc1): Section mismatch in reference
from the function acpi_map_cpu2node() to the function
.cpuinit.text:numa_set_node() The function acpi_map_cpu2node()
references the function __cpuinit numa_set_node(). This is often
because acpi_map_cpu2node lacks a __cpuinit annotation or the
annotation of numa_set_node is wrong.
WARNING: vmlinux.o(.text+0x526e77): Section mismatch in
reference from the function prealloc_protection_domains() to the
function .init.text:alloc_passthrough_domain() The function
prealloc_protection_domains() references the function __init
alloc_passthrough_domain(). This is often because
prealloc_protection_domains lacks a __init annotation or the annotation of alloc_passthrough_domain is wrong.
Signed-off-by: Steffen Persvold <sp@numascale.com>
Link: http://lkml.kernel.org/r/1331810188-24785-1-git-send-email-sp@numascale.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Adding sysfs group 'format' attribute for pmu device that
contains a syntax description on how to construct raw events.
The event configuration is described in following
struct pefr_event_attr attributes:
config
config1
config2
Each sysfs attribute within the format attribute group,
describes mapping of name and bitfield definition within
one of above attributes.
eg:
"/sys/...<dev>/format/event" contains "config:0-7"
"/sys/...<dev>/format/umask" contains "config:8-15"
"/sys/...<dev>/format/usr" contains "config:16"
the attribute value syntax is:
line: config ':' bits
config: 'config' | 'config1' | 'config2"
bits: bits ',' bit_term | bit_term
bit_term: VALUE '-' VALUE | VALUE
Adding format attribute definitions for x86 cpu pmus.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/n/tip-vhdk5y2hyype9j63prymty36@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
While running the latest Linux as guest under VMware in highly
over-committed situations, we have seen cases when the refined TSC
algorithm fails to get a valid tsc_start value in
tsc_refine_calibration_work from multiple attempts. As a result the
kernel keeps on scheduling the tsc_irqwork task for later. Subsequently
after several attempts when it gets a valid start value it goes through
the refined calibration and either bails out or uses the new results.
Given that the kernel originally read the TSC frequency from the
platform, which is the best it can get, I don't think there is much
value in refining it.
So for systems which get the TSC frequency from the platform we
should skip the refined tsc algorithm.
We can use the TSC_RELIABLE cpu cap flag to detect this, right now it is
set only on VMware and for Moorestown Penwell both of which have there
own TSC calibration methods.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
[jstultz: Reworked to simply not schedule the refining work,
rather then scheduling the work and bombing out later]
Signed-off-by: John Stultz <john.stultz@linaro.org>
The update of the vdso data happens under xtime_lock, so adding a
nested lock is pointless. Just use a seqcount to sync the readers.
Reviewed-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Changing the sequence count in update_vsyscall_tz() is completely
pointless.
The vdso code copies the data unprotected. There is no point to change
this as sys_tz is nowhere protected at all. See sys_gettimeofday().
Reviewed-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Move APIC ID validity check into platform APIC code, so it can
be overridden when needed. For NumaChip systems, always trust
MADT, as it's constructed with high APIC IDs.
Behaviour verifies on standard x86 systems and on NumaChip
systems with this, and compile-tested with allyesconfig.
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Reviewed-by: Steffen Persvold <sp@numascale.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1331709454-27966-1-git-send-email-daniel@numascale-asia.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into x86/mce
Merge reason: Update from an ancient -rc1 base to an almost-final stable kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Uprobes uses exception notifiers to get to know if a thread hit
a breakpoint or a singlestep exception.
When a thread hits a uprobe or is singlestepping post a uprobe
hit, the uprobe exception notifier sets its TIF_UPROBE bit,
which will then be checked on its return to userspace path
(do_notify_resume() ->uprobe_notify_resume()), where the
consumers handlers are run (in task context) based on the
defined filters.
Uprobe hits are thread specific and hence we need to maintain
information about if a task hit a uprobe, what uprobe was hit,
the slot where the original instruction was copied for xol so
that it can be singlestepped with appropriate fixups.
In some cases, special care is needed for instructions that are
executed out of line (xol). These are architecture specific
artefacts, such as handling RIP relative instructions on x86_64.
Since the instruction at which the uprobe was inserted is
executed out of line, architecture specific fixups are added so
that the thread continues normal execution in the presence of a
uprobe.
Postpone the signals until we execute the probed insn.
post_xol() path does a recalc_sigpending() before return to
user-mode, this ensures the signal can't be lost.
Uprobes relies on DIE_DEBUG notification to notify if a
singlestep is complete.
Adds x86 specific uprobe exception notifiers and appropriate
hooks needed to determine a uprobe hit and subsequent post
processing.
Add requisite x86 fixups for xol for uprobes. Specific cases
needing fixups include relative jumps (x86_64), calls, etc.
Where possible, we check and skip singlestepping the
breakpointed instructions. For now we skip single byte as well
as few multibyte nop instructions. However this can be extended
to other instructions too.
Credits to Oleg Nesterov for suggestions/patches related to
signal, breakpoint, singlestep handling code.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120313180011.29771.89027.sendpatchset@srdronam.in.ibm.com
[ Performed various cleanliness edits ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
.. as appropiately. As tboot_sleep now returns values.
remove tboot_sleep_wrapper.
Suggested-and-Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Joseph Cihula <joseph.cihula@intel.com>
[v1: Return -1/0/+1 instead of ACPI_xx values]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The ACPI suspend path makes a call to tboot_sleep right before
it writes the PM1A, PM1B values. We replace the direct call to
tboot via an registration callback similar to __acpi_register_gsi.
CC: Len Brown <len.brown@intel.com>
Acked-by: Joseph Cihula <joseph.cihula@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
[v1: Added __attribute__ ((unused))]
[v2: Introduced a wrapper instead of changing tboot_sleep return values]
[v3: Added return value AE_CTRL_SKIP for acpi_os_sleep_prepare]
Signed-off-by: Tang Liang <liang.tang@oracle.com>
[v1: Fix compile issues on IA64 and PPC64]
[v2: Fix where __acpi_os_prepare_sleep==NULL and did not go in sleep properly]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When a machine boots up, the TSC generally gets reset. However,
when kexec is used to boot into a kernel, the TSC value would be
carried over from the previous kernel. The computation of
cycns_offset in set_cyc2ns_scale is prone to an overflow, if the
machine has been up more than 208 days prior to the kexec. The
overflow happens when we multiply *scale, even though there is
enough room to store the final answer.
We fix this issue by decomposing tsc_now into the quotient and
remainder of division by CYC2NS_SCALE_FACTOR and then performing
the multiplication separately on the two components.
Refactor code to share the calculation with the previous
fix in __cycles_2_ns().
Signed-off-by: Salman Qazi <sqazi@google.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Turner <pjt@google.com>
Cc: john stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20120310004027.19291.88460.stgit@dungbeetle.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are precedences of trap number being referred to as
trap_nr. However thread struct refers trap number as trap_no.
Change it to trap_nr.
Also use enum instead of left-over literals for trap values.
This is pure cleanup, no functional change intended.
Suggested-by: Ingo Molnar <mingo@eltu.hu>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120312092555.5379.942.sendpatchset@srdronam.in.ibm.com
[ Fixed the math-emu build ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If a function takes struct uprobe or struct arch_uprobe, then it
is passed as the first parameter.
This is pure cleanup, no functional change intended.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120312092530.5379.18394.sendpatchset@srdronam.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the recent changes to clear_IO_APIC_pin() which tries to
clear remoteIRR bit explicitly, some of the users started to see
"Unable to reset IRR for apic .." messages.
Close look shows that these are related to bogus IO-APIC entries
which return's all 1's for their io-apic registers. And the
above mentioned error messages are benign. But kernel should
have ignored such io-apic's in the first place.
Check if register 0, 1, 2 of the listed io-apic are all 1's and
ignore such io-apic.
Reported-by: Álvaro Castillo <midgoon@gmail.com>
Tested-by: Jon Dufresne <jon@jondufresne.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: kernel-team@fedoraproject.org
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1331577393.31585.94.camel@sbsiddha-desk.sc.intel.com
[ Performed minor cleanup of affected code. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I got somewhat tired of having to decode hex numbers..
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/n/tip-0vsy1sgywc4uar3mu1szm0rg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Robert Richter
Ingo Molnar
Peter Zijlstra
Jan Beulich
Jarkko Sakkinen
Linus Torvalds
Tejun Heo
Thomas Gleixner
Márton Németh
Shuah Khan
Srivatsa S. Bhat
Shai Fultheim
Suresh Siddha
Joerg Roedel
Larry Finger
Gleb Natapov
Steven Rostedt
James Morris
Konrad Rzeszutek Wilk
Borislav Petkov
Andreas Herrmann
Greg Pearson
Li Zhong
Don Zickus
Chen Gong
H. Peter Anvin
Marcelo Tosatti
Tony Luck
Bryan O'Donoghue
Oleg Nesterov
Josh Triplett
Will Drewry
Eric B Munson
Emil Goode
Stephen Boyd
Len Brown
Petr Vandrovec
Boris Ostrovsky
Jason Wessel
Liu, Chuansheng
Dave Young
David Howells
Dan Carpenter
Andrzej Pietrasiewicz
Jeremy Fitzhardinge
Richard Weinberger
Hugh Dickins
Akinobu Mita
Andy Lutomirski
Alexander Gordeev
Steffen Persvold
Yinghai Lu
Peter Zijlstra
Dmitry Adamushko
Jan Kiszka
Xiao Guangrong
Andrea Arcangeli
Cong Wang
Jiri Olsa
Alok Kataria
Daniel J Blueman
Ingo Molnar
Srikar Dronamraju
Tang Liang
Salman Qazi