Граф коммитов

5 Коммитов

Автор SHA1 Сообщение Дата
Andy Shevchenko bcc567e311 dmatest: do not allow to interrupt ongoing tests
When user interrupts ongoing transfers the dmatest may end up with console
lockup, oops, or data mismatch. This patch prevents user to abort any ongoing
test.

Documentation is updated accordingly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2013-06-08 02:13:44 +05:30
Andy Shevchenko d86b2f298e dmatest: append verify result to results
Comparison between buffers is stored to the dedicated structure.

Note that the verify result is now accessible only via file 'results' in the
debugfs.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2013-04-15 09:51:18 +05:30
Andy Shevchenko 95019c8c5a dmatest: gather test results in the linked list
The patch provides a storage for the test results in the linked list. The
gathered data could be used after test is done.

The new file 'results' represents gathered data of the in progress test. The
messages collected are printed to the kernel log as well.

Example of output:
	% cat /sys/kernel/debug/dmatest/results
	dma0chan0-copy0: #1: No errors with src_off=0x7bf dst_off=0x8ad len=0x3fea (0)

The message format is unified across the different types of errors. A number in
the parens represents additional information, e.g. error code, error counter,
or status.

Note that the buffer comparison is done in the old way, i.e. data is not
collected and just printed out.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2013-04-15 09:51:17 +05:30
Andy Shevchenko 3e5ccd866f dmatest: return actual state in 'run' file
The following command should return actual state of the test.
	% cat /sys/kernel/debug/dmatest/run

To wait for test done the user may perform a busy loop that checks the state.
	% while [ $(cat /sys/kernel/debug/dmatest/run) = "Y" ]
	> do
	> 	echo -n "."
	> 	sleep 1
	> done
	> echo

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2013-04-15 09:51:17 +05:30
Andy Shevchenko 851b7e16a0 dmatest: run test via debugfs
Instead of doing
	modprobe dmatest ...
	modprobe -r dmatest
we allow user to run tests interactively.

The dmatest could be built as module or inside kernel. Let's consider those
cases.

1. When dmatest is built as a module...

After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest
folder with nodes will be created. They are the same as module parameters with
addition of the 'run' node that controls run and stop phases of the test.

Note that in this case test will not run on load automatically.

Example of usage:
	% echo dma0chan0 > /sys/kernel/debug/dmatest/channel
	% echo 2000 > /sys/kernel/debug/dmatest/timeout
	% echo 1 > /sys/kernel/debug/dmatest/iterations
	% echo 1 > /sys/kernel/debug/dmatest/run

After a while you will start to get messages about current status or error like
in the original code.

Note that running a new test will stop any in progress test.

2. When built-in in the kernel...

The module parameters that is supplied to the kernel command line will be used
for the first performed test. After user gets a control, the test could be
interrupted or re-run with same or different parameters. For the details see
the above section "1. When dmatest is built as a module..."

In both cases the module parameters are used as initial values for the test case.
You always could check them at run-time by running
	% grep -H . /sys/module/dmatest/parameters/*

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2013-04-15 09:51:17 +05:30