net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a "%" after pending_idx instead of ":".
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An old inefficiency of the TX path that we are grant mapping the first slot,
and then copy the header part to the linear area. Instead, doing a grant copy
for that header straight on is more reasonable. Especially because there are
ongoing efforts to make Xen avoiding TLB flush after unmap when the page were
not touched in Dom0. In the original way the memcpy ruined that.
The key changes:
- the vif has a tx_copy_ops array again
- xenvif_tx_build_gops sets up the grant copy operations
- we don't have to figure out whether the header and first frag are on the same
grant mapped page or not
Note, we only grant copy PKT_PROT_LEN bytes from the first slot, the rest (if
any) will be on the first frag, which is grant mapped. If the first slot is
smaller than PKT_PROT_LEN, then we grant copy that, and later __pskb_pull_tail
will pull more from the frags (if any)
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename identifiers to state explicitly that they refer to map ops.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netback discovers frontend is sending malformed packet it will
disables the interface which serves that frontend.
However disabling a network interface involving taking a mutex which
cannot be done in softirq context, so we need to defer this process to
kthread context.
This patch does the following:
1. introduce a flag to indicate the interface is disabled.
2. check that flag in TX path, don't do any work if it's true.
3. check that flag in RX path, turn off that interface if it's true.
The reason to disable it in RX path is because RX uses kthread. After
this change the behavior of netback is still consistent -- it won't do
any TX work for a rogue frontend, and the interface will be eventually
turned off.
Also change a "continue" to "break" after xenvif_fatal_tx_err, as it
doesn't make sense to continue processing packets if frontend is rogue.
This is a fix for XSA-90.
Reported-by: Török Edwin <edwin@etorok.net>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netback/netback.c
A bug fix overlapped with changing how the netback SKB control
block is implemented.
Signed-off-by: David S. Miller <davem@davemloft.net>
The BUG_ON to catch ring overflow in xenvif_rx_action() makes the assumption
that meta_slots_used == ring slots used. This is not necessarily the case
for GSO packets, because the non-prefix GSO protocol consumes one more ring
slot than meta-slot for the 'extra_info'. This patch changes the test to
actually check ring slots.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The worse-case estimate for skb ring slot usage in xenvif_rx_action()
fails to take fragment page_offset into account. The page_offset does,
however, affect the number of times the fragmentation code calls
start_new_rx_buffer() (i.e. consume another slot) and the worse-case
should assume that will always return true. This patch adds the page_offset
into the DIV_ROUND_UP for each frag.
Unfortunately some frontends aggressively limit the number of requests
they post into the shared ring so to avoid an estimate that is 'too'
pessimal it is capped at MAX_SKB_FRAGS.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a test in start_new_rx_buffer() that checks whether
a copy operation is less than MAX_BUFFER_OFFSET in length, since
MAX_BUFFER_OFFSET is defined to be PAGE_SIZE and the only caller of
start_new_rx_buffer() already limits copy operations to PAGE_SIZE or less.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Reported-By: Sander Eikelenboom <linux@eikelenboom.it>
Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian made some late comments about the grant mapping series, I incorporated the
functional outcomes into this patch:
- use callback_param macro to shorten access to pending_tx_info in
xenvif_fill_frags() and xenvif_tx_submit()
- print an error message in xenvif_idx_unmap() before panic
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian made some late comments about the grant mapping series, I incorporated the
non-functional outcomes into this patch:
- typo fixes in a comment of xenvif_free(), and add another one there as well
- typo fix for comment of rx_drain_timeout_msecs
- remove stale comment before calling xenvif_grant_handle_reset()
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the early days TX stops if there isn't enough free pending slots to
consume a maximum sized (slot-wise) packet. Probably the reason for that is to
avoid the case when we don't have enough free pending slot in the ring to finish
the packet. But if we make sure that the pending ring has the same size as the
shared ring, that shouldn't really happen. The frontend can only post packets
which fit the to the free space of the shared ring. If it doesn't, the frontend
has to stop, as it can only increase the req_prod when the whole packet fits
onto the ring.
This patch avoid using this checking, makes sure the 2 ring has the same size,
and remove a checking from the callback. As now we don't stop the NAPI instance
on this condition, we don't have to wake it up if we free pending slots up.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes:
drivers/net/xen-netback/netback.c: In function ‘xenvif_tx_dealloc_action’:
drivers/net/xen-netback/netback.c:1573:8: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long int’ [-Wformat=]
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e9275f5e2d. This commit is the
last in the netback grant mapping series, and it tries to do more aggressive
aggreagtion of unmap operations. However practical use showed almost no
positive effect, whilst with certain frontends it causes significant performance
regression.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In 5bd076708 ("Xen-netback: Fix issue caused by using gso_type wrongly")
we use skb_is_gso to determine if we need an extra slot to accommodate
the SKB. There's similar error in interface.c. Change that to use
skb_is_gso as well.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current netback uses gso_type to check whether the skb contains
gso offload, and this is wrong. Gso_size is the right one to
check gso existence, and gso_type is only used to check gso type.
Some skbs contains nonzero gso_type and zero gso_size, current
netback would treat these skbs as gso and create wrong response
for this. This also causes ssh failure to domu from other server.
V2: use skb_is_gso function as Paul Durrant suggested
Signed-off-by: Annie Li <annie.li@oracle.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmapping causes TLB flushing, therefore we should make it in the largest
possible batches. However we shouldn't starve the guest for too long. So if
the guest has space for at least two big packets and we don't have at least a
quarter ring to unmap, delay it for at most 1 milisec.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious or buggy guest can leave its queue filled indefinitely, in which
case qdisc start to queue packets for that VIF. If those packets came from an
another guest, it can block its slots and prevent shutdown. To avoid that, we
make sure the queue is drained in every 10 seconds.
The QDisc queue in worst case takes 3 round to flush usually.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xen network protocol had implicit dependency on MAX_SKB_FRAGS. Netback has to
handle guests sending up to XEN_NETBK_LEGACY_SLOTS_MAX slots. To achieve that:
- create a new skb
- map the leftover slots to its frags (no linear buffer here!)
- chain it to the previous through skb_shinfo(skb)->frag_list
- map them
- copy and coalesce the frags into a brand new one and send it to the stack
- unmap the 2 old skb's pages
It's also introduces new stat counters, which help determine how often the guest
sends a packet with more than MAX_SKB_FRAGS frags.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise malicious guests can block
other guests by not releasing their sent packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These counters help determine how often the buffers had to be copied. Also
they help find out if packets are leaked, as if "sent != success + fail",
there are probably packets never freed up properly.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These became obsolete with grant mapping. I've left intentionally the
indentations in this way, to improve readability of previous patches.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces grant mapping on netback TX path. It replaces grant copy
operations, ditching grant copy coalescing along the way. Another solution for
copy coalescing is introduced in "xen-netback: Handle guests with too many
frags", older guests and Windows can broke before that patch applies.
There is a callback (xenvif_zerocopy_callback) from core stack to release the
slots back to the guests when kfree_skb or skb_orphan_frags called. It feeds a
separate dealloc thread, as scheduling NAPI instance from there is inefficient,
therefore we can't do dealloc from the instance.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX path need to know if the SKB fragments are stored on pages from another
domain.
Logically this patch should be after introducing the grant mapping itself, as
it makes sense only after that. But to keep bisectability, I moved it here. It
shouldn't change any functionality here. xenvif_zerocopy_callback and
ubuf_to_vif are just stubs here, they will be introduced properly later on.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a few bits of refactoring before introducing the grant
mapping changes:
- introducing xenvif_tx_pending_slots_available(), as this is used several
times, and will be used more often
- rename the thread to vifX.Y-guest-rx, to signify it does RX work from the
guest point of view
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing the pending_idx at the first byte of the linear buffer never looked
good, skb->cb is a more proper place for this. It also prevents the header to
be directly grant copied there, and we don't have the pending_idx after we
copied the header here, so it's time to change it.
It also introduces helpers for the RX side
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch to fix receive side flow control
(11b57f90257c1d6a91cee720151b69e0c2020cf6: xen-netback: stop vif thread
spinning if frontend is unresponsive) solved the spinning thread problem,
however caused an another one. The receive side can stall, if:
- [THREAD] xenvif_rx_action sets rx_queue_stopped to true
- [INTERRUPT] interrupt happens, and sets rx_event to true
- [THREAD] then xenvif_kthread sets rx_event to false
- [THREAD] rx_work_todo doesn't return true anymore
Also, if interrupt sent but there is still no room in the ring, it take quite a
long time until xenvif_rx_action realize it. This patch ditch that two variable,
and rework rx_work_todo. If the thread finds it can't fit more skb's into the
ring, it saves the last slot estimation into rx_last_skb_slots, otherwise it's
kept as 0. Then rx_work_todo will check if:
- there is something to send to the ring (like before)
- there is space for the topmost packet in the queue
I think that's more natural and optimal thing to test than two bool which are
set somewhere else.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_setup to set up partial checksum offsets rather
then a private implementation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch to improve guest receive side flow control (ca2f09f2) had a
slight flaw in the wait condition for the vif thread in that any remaining
skbs in the guest receive side netback internal queue would prevent the
thread from sleeping. An unresponsive frontend can lead to a permanently
non-empty internal queue and thus the thread will spin. In this case the
thread should really sleep until the frontend becomes responsive again.
This patch adds an extra flag to the vif which is set if the shared ring
is full and cleared when skbs are drained into the shared ring. Thus,
if the thread runs, finds the shared ring full and can make no progress the
flag remains set. If the flag remains set then the thread will sleep,
regardless of a non-empty queue, until the next event from the frontend.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ac3d5ac277 ("xen-netback: fix guest-receive-side array sizes")
added calls to vmalloc and vfree in the interface.c file without including
<linux/vmalloc.h>. This causes build failures if the
-Werror=implicit-function-declaration flag is passed.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sizes chosen for the metadata and grant_copy_op arrays on the guest
receive size are wrong;
- The meta array is needlessly twice the ring size, when we only ever
consume a single array element per RX ring slot
- The grant_copy_op array is way too small. It's sized based on a bogus
assumption: that at most two copy ops will be used per ring slot. This
may have been true at some point in the past but it's clear from looking
at start_new_rx_buffer() that a new ring slot is only consumed if a frag
would overflow the current slot (plus some other conditions) so the actual
limit is MAX_SKB_FRAGS grant_copy_ops per ring slot.
This patch fixes those two sizing issues and, because grant_copy_ops grows
so much, it pulls it out into a separate chunk of vmalloc()ed memory.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netback already has code which parses IPv4 and v6 headers to set up checksum
offsets and these are always applied to GSO packets being sent from
frontends. It's therefore suboptimal that GSOs are being marked
SKB_GSO_DODGY to defer the gso_segs calculation when netback already has all
necessary information to hand to do the calculation. This patch adds that
calculation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'err' is overwrited to 0 after maybe_pull_tail() call, so the error
code was not set if skb_partial_csum_set() call failed. Fix to return
error -EPROTO from those error handling case instead of 0.
Fixes: d52eb0d46f ('xen-netback: make sure skb linear area covers checksum field')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -EPROTO error if fragments detected in checksum_setup_ip().
Fixes: 1431fb31ec ('xen-netback: fix fragment detection in checksum setup')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a mistake in checking the gso_prefix mask when passing large
packets to a guest. The wrong shift is applied to the bit - the raw skb
gso type is used rather then the translated one. This leads to large packets
being handed to the guest without the GSO metadata. This patch fixes the
check.
The mistake manifested as errors whilst running Microsoft HCK large packet
offload tests between a pair of Windows 8 VMs. I have verified this patch
fixes those errors.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the RING_FINAL_CHECK_FOR_REQUESTS in
xenvif_build_tx_gops to a check for RING_HAS_UNCONSUMED_REQUESTS as the
former call has the side effect of advancing the ring event pointer and
therefore inviting another interrupt from the frontend before the napi
poll has actually finished, thereby defeating the point of napi.
The event pointer is updated by RING_FINAL_CHECK_FOR_REQUESTS in
xenvif_poll, the napi poll function, if the work done is less than the
budget i.e. when actually transitioning back to interrupt mode.
Reported-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netback seems to be somewhat confused about the napi budget parameter. The
parameter is supposed to limit the number of skbs processed in each poll,
but netback has this confused with grant operations.
This patch fixes that, properly limiting the work done in each poll. Note
that this limit makes sure we do not process any more data from the shared
ring than we intend to pass back from the poll. This is important to
prevent tx_queue potentially growing without bound.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_partial_csum_set requires that the linear area of the skb covers the
checksum field. The checksum setup code in netback was only doing that
pullup in the case when the pseudo header checksum was being recalculated
though. This patch makes that pullup unconditional. (I pullup the whole
transport header just for simplicity; the requirement is only for the check
field but in the case of UDP this is the last field in the header and in the
case of TCP it's the last but one).
The lack of pullup manifested as failures running Microsoft HCK network
tests on a pair of Windows 8 VMs and it has been verified that this patch
fixes the problem.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way that flow control works without this patch is that, in start_xmit()
the code uses xenvif_count_skb_slots() to predict how many slots
xenvif_gop_skb() will consume and then adds this to a 'req_cons_peek'
counter which it then uses to determine if the shared ring has that amount
of space available by checking whether 'req_prod' has passed that value.
If the ring doesn't have space the tx queue is stopped.
xenvif_gop_skb() will then consume slots and update 'req_cons' and issue
responses, updating 'rsp_prod' as it goes. The frontend will consume those
responses and post new requests, by updating req_prod. So, req_prod chases
req_cons which chases rsp_prod, and can never exceed that value. Thus if
xenvif_count_skb_slots() ever returns a number of slots greater than
xenvif_gop_skb() uses, req_cons_peek will get to a value that req_prod cannot
possibly achieve (since it's limited by the 'real' req_cons) and, if this
happens enough times, req_cons_peek gets more than a ring size ahead of
req_cons and the tx queue then remains stopped forever waiting for an
unachievable amount of space to become available in the ring.
Having two routines trying to calculate the same value is always going to be
fragile, so this patch does away with that. All we essentially need to do is
make sure that we have 'enough stuff' on our internal queue without letting
it build up uncontrollably. So start_xmit() makes a cheap optimistic check
of how much space is needed for an skb and only turns the queue off if that
is unachievable. net_rx_action() is the place where we could do with an
accurate predicition but, since that has proven tricky to calculate, a cheap
worse-case (but not too bad) estimate is all we really need since the only
thing we *must* prevent is xenvif_gop_skb() consuming more slots than are
available.
Without this patch I can trivially stall netback permanently by just doing
a large guest to guest file copy between two Windows Server 2008R2 VMs on a
single host.
Patch tested with frontends in:
- Windows Server 2008R2
- CentOS 6.0
- Debian Squeeze
- Debian Wheezy
- SLES11
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Paul Mackerras <paulus@samba.org>
CC: Ian Campbell <ian.campbell@citrix.com>
CC: Wei Liu <wei.liu2@citrix.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to detect fragments in checksum_setup() was missing for IPv4 and
too eager for IPv6. (It transpires that Windows seems to send IPv6 packets
with a fragment header even if they are not a fragment - i.e. offset is zero,
and M bit is not set).
This patch also incorporates a fix to callers of maybe_pull_tail() where
skb->network_header was being erroneously added to the length argument.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
cc: David Miller <davem@davemloft.net>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xenvif_start_xmit() relies on checking vif->task for NULL to determine
whether the vif is ready to accept packets. The task thread is stopped in
xenvif_disconnect() but task is not set to NULL. Thus, on a re-connect the
check will give a false positive.
Also since commit ea732dff5c (Handle backend
state transitions in a more robust way) it should not be possible for
xenvif_connect() to be called if the vif is already connected so change the
check of vif->tx_irq to a BUG_ON() and also add a BUG_ON(vif->task).
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are now using csum_ipv6_magic, include the appropriate header.
Avoids the following error:
drivers/net/xen-netback/netback.c:1313:4: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
tcph->check = ~csum_ipv6_magic(&ipv6h->saddr,
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the VIF thread is still running after unbinding the Tx and Rx IRQs
in xenvif_disconnect(), the thread may attempt to raise an event which
will BUG (as the irq is unbound).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
time_after_eq() only works if the delta is < MAX_ULONG/2.
For a 32bit Dom0, if netfront sends packets at a very low rate, the time
between subsequent calls to tx_credit_exceeded() may exceed MAX_ULONG/2
and the test for timer_after_eq() will be incorrect. Credit will not be
replenished and the guest may become unable to send packets (e.g., if
prior to the long gap, all credit was exhausted).
Use jiffies_64 variant to mitigate this problem for 32bit Dom0.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jason Luan <jianhai.luan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to handle SKB_GSO_TCPV6 skbs and construct appropriate
extra or prefix segments to pass the large packet to the frontend. New
xenstore flags, feature-gso-tcpv6 and feature-gso-tcpv6-prefix, are sampled
to determine if the frontend is capable of handling such packets.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a xenstore feature flag, festure-gso-tcpv6, to advertise
that netback can handle IPv6 TCP GSO packets. It creates SKB_GSO_TCPV6 skbs
if the frontend passes an extra segment with the new type
XEN_NETIF_GSO_TYPE_TCPV6 added to netif.h.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no mechanism to insist that a guest always generates a packet
with good checksum (at least for IPv4) so we must handle checksum
offloading from the guest and hence should set NETIF_F_RXCSUM.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For performance of VM to VM traffic on a single host it is better to avoid
calculation of TCP/UDP checksum in the sending frontend. To allow this this
patch adds the code necessary to set up partial checksum for IPv6 packets
and xenstore flag feature-ipv6-csum-offload to advertise that fact to
frontends.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check xenstore flag feature-ipv6-csum-offload to determine if a
guest is happy to accept IPv6 packets with only partial checksum.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a guest is destroyed without transitioning its frontend to CLOSED,
the domain becomes a zombie as netback was not grant unmapping the
shared rings.
When removing a VIF, transition the backend to CLOSED so the VIF is
disconnected if necessary (which will unmap the shared rings etc).
This fixes a regression introduced by
279f438e36 (xen-netback: Don't destroy
the netdev until the vif is shut down).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Paul Durrant <Paul.Durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.
With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VM is providing an iSCSI target and the LUN is used by the
backend domain, the generated skbs for direct I/O writes to the disk
have large, multi-page skb->data but no frags.
With some lengths and starting offsets, xen_netbk_count_skb_slots()
would be one short because the simple calculation of
DIV_ROUND_UP(skb_headlen(), PAGE_SIZE) was not accounting for the
decisions made by start_new_rx_buffer() which does not guarantee
responses are fully packed.
For example, a skb with length < 2 pages but which spans 3 pages would
be counted as requiring 2 slots but would actually use 3 slots.
skb->data:
| 1111|222222222222|3333 |
Fully packed, this would need 2 slots:
|111122222222|22223333 |
But because the 2nd page wholy fits into a slot it is not split across
slots and goes into a slot of its own:
|1111 |222222222222|3333 |
Miscounting the number of slots means netback may push more responses
than the number of available requests. This will cause the frontend
to get very confused and report "Too many frags/slots". The frontend
never recovers and will eventually BUG.
Fix this by counting the number of required slots more carefully. In
xen_netbk_count_skb_slots(), more closely follow the algorithm used by
xen_netbk_gop_skb() by introducing xen_netbk_count_frag_slots() which
is the dry-run equivalent of netbk_gop_frag_copy().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure a format string cannot accidentally leak into the
kthread_run() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we move to 1:1 model and melt xen_netbk and xenvif together, it would
be better to use single prefix for all functions in xen-netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements 1:1 model netback. NAPI and kthread are utilized
to do the weight-lifting job:
- NAPI is used for guest side TX (host side RX)
- kthread is used for guest side RX (host side TX)
Xenvif and xen_netbk are made into one structure to reduce code size.
This model provides better scheduling fairness among vifs. It is also
prerequisite for implementing multiqueue for Xen netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data flow from DomU to DomU on the same host in current copying
scheme with tracking facility:
copy
DomU --------> Dom0 DomU
| ^
|____________________________|
copy
The page in Dom0 is a page with valid MFN. So we can always copy from
page Dom0, thus removing the need for a tracking facility.
copy copy
DomU --------> Dom0 -------> DomU
Simple iperf test shows no performance regression (obviously we copy
twice either way):
W/ tracking: ~5.3Gb/s
W/o tracking: ~5.4Gb/s
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Matt Wilson <msw@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert one printk to pr_<level>.
Add a missing newline in several places to avoid message interleaving,
coalesce formats, reflow modified lines to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of mixing printk and pr_<level> forms,
just use pr_<level>
Miscellaneous changes around these conversions:
Add a missing newline to avoid message interleaving,
coalesce formats, reflow modified lines to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here, "i" vs "j", so we would crash on module_exit().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When putting vif-s on the rx notify list, calling xenvif_put() must be
deferred until after the removal from the list and the issuing of the
notification, as both operations dereference the pointer.
Changing this got me to notice that the "irq" variable was effectively
unused (and was of too narrow type anyway).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netback and netfront only use one event channel to do TX / RX notification,
which may cause unnecessary wake-up of processing routines. This patch adds a
new feature called feature-split-event-channels to netback, enabling it to
handle TX and RX events separately.
Netback will use tx_irq to notify guest for TX completion, rx_irq for RX
notification.
If frontend doesn't support this feature, tx_irq equals to rx_irq.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables user to unload netback module, which is useful when user
wants to upgrade to a newer netback module without rebooting the host.
Netfront cannot handle netback removal event. As we cannot fix all possible
frontends we add module get / put along with vif get / put to avoid
mis-unloading of netback. To unload netback module, user needs to shutdown all
VMs or migrate them to another host or unplug all vifs before hand.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>¬
Signed-off-by: David S. Miller <davem@davemloft.net>
The array mmap_pages is never touched in the initialization function. This is
remnant of mapping mechanism, which does not exist upstream. In current
upstream code this array only tracks usage of pages inside netback. Those
pages are allocated when contructing a SKB and passed directly to network
subsystem.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch only changes some names to avoid confusion.
In this patch we have:
MAX_SKB_SLOTS_DEFAULT -> FATAL_SKB_SLOTS_DEFAULT
max_skb_slots -> fatal_skb_slots
#define XEN_NETBK_LEGACY_SLOTS_MAX XEN_NETIF_NR_SLOTS_MIN
The fatal_skb_slots is the threshold to determine whether a packet is
malicious.
XEN_NETBK_LEGACY_SLOTS_MAX is the maximum slots a valid packet can have at
this point. It is defined to be XEN_NETIF_NR_SLOTS_MIN because that's
guaranteed to be supported by all backends.
Suggested-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tune xen_netbk_count_requests to not touch working array beyond limit, so that
we can make working array size constant.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tracking down from the caller, first_idx is always equal to vif->tx.req_cons.
Remove it to avoid confusion.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some frontend drivers are sending packets > 64 KiB in length. This length
overflows the length field in the first slot making the following slots have
an invalid length.
Turn this error back into a non-fatal error by dropping the packet. To avoid
having the following slots having fatal errors, consume all slots in the
packet.
This does not reopen the security hole in XSA-39 as if the packet as an
invalid number of slots it will still hit fatal error case.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tries to coalesce tx requests when constructing grant copy
structures. It enables netback to deal with situation when frontend's
MAX_SKB_FRAGS is larger than backend's MAX_SKB_FRAGS.
With the help of coalescing, this patch tries to address two regressions
avoid reopening the security hole in XSA-39.
Regression 1. The reduction of the number of supported ring entries (slots)
per packet (from 18 to 17). This regression has been around for some time but
remains unnoticed until XSA-39 security fix. This is fixed by coalescing
slots.
Regression 2. The XSA-39 security fix turning "too many frags" errors from
just dropping the packet to a fatal error and disabling the VIF. This is fixed
by coalescing slots (handling 18 slots when backend's MAX_SKB_FRAGS is 17)
which rules out false positive (using 18 slots is legit) and dropping packets
using 19 to `max_skb_slots` slots.
To avoid reopening security hole in XSA-39, frontend sending packet using more
than max_skb_slots is considered malicious.
The behavior of netback for packet is thus:
1-18 slots: valid
19-max_skb_slots slots: drop and respond with an error
max_skb_slots+ slots: fatal error
max_skb_slots is configurable by admin, default value is 20.
Also change variable name from "frags" to "slots" in netbk_count_requests.
Please note that RX path still has dependency on MAX_SKB_FRAGS. This will be
fixed with separate patch.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use skb_partial_csum_set() to simplify the codes.
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use the new help skb_probe_transport_header() to do the l4 header
probing for untrusted sources. For packets with partial csum, the header should
already been set by skb_partial_csum_set().
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, for the packets receives from netback, before doing header check,
kernel just reset the transport header in netif_receive_skb() which pretends non
l4 header. This is suboptimal for precise packet length estimation (introduced
in 1def9238: net_sched: more precise pkt_len computation) which needs correct l4
header for gso packets.
The patch just reuse the header probed by netback for partial checksum packets
and tries to use skb_flow_dissect() for other cases, if both fail, just pretend
no l4 header.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is never used.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d37204566a.
This change is incorrect, as per Jan Beulich:
====================
But this is wrong from all we can tell, we discussed this before
(Wei pointed to the discussion in an earlier reply). The core of
it is that the put here parallels the one in netbk_tx_err(), and
the one in xenvif_carrier_off() matches the get from
xenvif_connect() (which normally would be done on the path
coming through xenvif_disconnect()).
====================
And a previous discussion of this issue is at:
http://marc.info/?l=xen-devel&m=136084174026977&w=2
Signed-off-by: David S. Miller <davem@davemloft.net>
netbk_fatal_tx_err() calls xenvif_carrier_off(), which does
a xenvif_put(). As callers of netbk_fatal_tx_err should only
have one reference to the vif at this time, then the xenvif_put
in netbk_fatal_tx_err is one too many.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the credit timer is left armed after calling
xen_netbk_remove_xenvif(), then it may fire and attempt to schedule
the vif which will then oops as vif->netbk == NULL.
This may happen both in the fatal error path and during normal
disconnection from the front end.
The sequencing during shutdown is critical to ensure that: a)
vif->netbk doesn't become unexpectedly NULL; and b) the net device/vif
is not freed.
1. Mark as unschedulable (netif_carrier_off()).
2. Synchronously cancel the timer.
3. Remove the vif from the schedule list.
4. Remove it from it netback thread group.
5. Wait for vif->refcnt to become 0.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Reported-by: Christopher S. Aker <caker@theshore.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
netbk_count_requests() could detect an error, call
netbk_fatal_tx_error() but return 0. The vif may then be used
afterwards (e.g., in a call to netbk_tx_error().
Since netbk_fatal_tx_error() could set vif->refcnt to 1, the vif may
be freed immediately after the call to netbk_fatal_tx_error() (e.g.,
if the vif is also removed).
Netback thread Xenwatch thread
-------------------------------------------
netbk_fatal_tx_err() netback_remove()
xenvif_disconnect()
...
free_netdev()
netbk_tx_err() Oops!
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Christopher S. Aker <caker@theshore.net>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthew Daley <mattjd@gmail.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A buggy or malicious frontend should not be able to confuse netback.
If we spot anything which is not as it should be then shutdown the
device and don't try to continue with the ring in a potentially
hostile state. Well behaved and non-hostile frontends will not be
penalised.
As well as making the existing checks for such errors fatal also add a
new check that ensures that there isn't an insane number of requests
on the ring (i.e. more than would fit in the ring). If the ring
contains garbage then previously is was possible to loop over this
insane number, getting an error each time and therefore not generating
any more pending requests and therefore not exiting the loop in
xen_netbk_tx_build_gops for an externded period.
Also turn various netdev_dbg calls which no precipitate a fatal error
into netdev_err, they are rate limited because the device is shutdown
afterwards.
This fixes at least one known DoS/softlockup of the backend domain.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it is useful to be able to change the MAC address of the
interface for netback devices. For example, when using ebtables it may
be useful to be able to distinguish traffic from different interfaces
without depending on the interface name.
Reported-by: Nikita Borzykh <sample.n@gmail.com>
Reported-by: Paul Harvey <stockingpaul@hotmail.com>
Cc: netdev@vger.kernel.org
Cc: xen-devel@lists.xen.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Matt Wilson <msw@amazon.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SKB paged fragment can consist of a compound page with order > 0.
However the netchannel protocol deals only in PAGE_SIZE frames.
Handle this in netbk_gop_frag_copy and xen_netbk_count_skb_slots by
iterating over the frames which make up the page.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'xenarm-for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
arm: introduce a DTS for Xen unprivileged virtual machines
MAINTAINERS: add myself as Xen ARM maintainer
xen/arm: compile netback
xen/arm: compile blkfront and blkback
xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree
xen/arm: receive Xen events on ARM
xen/arm: initialize grant_table on ARM
xen/arm: get privilege status
xen/arm: introduce CONFIG_XEN on ARM
xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM
xen/arm: Introduce xen_ulong_t for unsigned long
xen/arm: Xen detection and shared_info page mapping
docs: Xen ARM DT bindings
xen/arm: empty implementation of grant_table arch specific functions
xen/arm: sync_bitops
xen/arm: page.h definitions
xen/arm: hypercalls
arm: initial Xen support
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since Xen-4.2, hvm domains may have portions of their memory paged out. When a
foreign domain (such as dom0) attempts to map these frames, the map will
initially fail. The hypervisor returns a suitable errno, and kicks an
asynchronous page-in operation carried out by a helper. The foreign domain is
expected to retry the mapping operation until it eventually succeeds. The
foreign domain is not put to sleep because itself could be the one running the
pager assist (typical scenario for dom0).
This patch adds support for this mechanism for backend drivers using grant
mapping and copying operations. Specifically, this covers the blkback and
gntdev drivers (which map foreign grants), and the netback driver (which copies
foreign grants).
* Add a retry method for grants that fail with GNTST_eagain (i.e. because the
target foreign frame is paged out).
* Insert hooks with appropriate wrappers in the aforementioned drivers.
The retry loop is only invoked if the grant operation status is GNTST_eagain.
It guarantees to leave a new status code different from GNTST_eagain. Any other
status code results in identical code execution as before.
The retry loop performs 256 attempts with increasing time intervals through a
32 second period. It uses msleep to yield while waiting for the next retry.
V2 after feedback from David Vrabel:
* Explicit MAX_DELAY instead of wrap-around delay into zero
* Abstract GNTST_eagain check into core grant table code for netback module.
V3 after feedback from Ian Campbell:
* Add placeholder in array of grant table error descriptions for unrelated
error code we jump over.
* Eliminate single map and retry macro in favor of a generic batch flavor.
* Some renaming.
* Bury most implementation in grant_table.c, cleaner interface.
V4 rebased on top of sync of Xen grant table interface headers.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
[v5: Fixed whitespace issues]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
After SKB is queued into tx_queue, it will be freed if request_gop is NULL.
However, no dequeue action is called in this situation, it is likely that
tx_queue constains freed SKB. This patch should fix this issue, and it is
based on 3.5.0-rc4+.
This issue is found through code inspection, no bug is seen with it currently.
I run netperf test for several hours, and no network regression was found.
Signed-off-by: Annie Li <annie.li@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating the number of slots required for a packet header, the code
was reserving too many slots if the header crossed a page boundary. Since
netbk_gop_skb copies the header to the start of the page, the count of
slots required for the header should be based solely on the header size.
This problem is easy to reproduce if a VIF is bridged to a USB 3G modem
device as the skb->data value always starts near the end of the first page.
Signed-off-by: Simon Graham <simon.graham@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
All tables of function pointers should be const to make hacks
more difficult. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'name', 'owner', and 'mod_name' members are redundant with the
identically named fields in the 'driver' sub-structure. Rather than
switching each instance to specify these fields explicitly, introduce
a macro to simplify this.
Eliminate further redundancy by allowing the drvname argument to
DEFINE_XENBUS_DRIVER() to be blank (in which case the first entry from
the ID table will be used for .driver.name).
Also eliminate the questionable xenbus_register_{back,front}end()
wrappers - their sole remaining purpose was the checking of the
'owner' field, proper setting of which shouldn't be an issue anymore
when the macro gets used.
v2: Restore DRV_NAME for the driver name in xen-pciback.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
"variables a used" should be "variables are used".
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New value for netbk->mmap_pages[pending_idx] is assigned in
xen_netbk_alloc_page(), no need for a second assignment which
exposes internal to the outside world.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original message in netback_init was 'kthread_run() fails', which should be
'kthread_create() fails'.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'stable/vmalloc-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
net: xen-netback: use API provided by xenbus module to map rings
block: xen-blkback: use API provided by xenbus module to map rings
xen: use generic functions instead of xen_{alloc, free}_vm_area()
The xenbus module provides xenbus_map_ring_valloc() and
xenbus_map_ring_vfree(). Use these to map the Tx and Rx ring pages
granted by the frontend.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netback currently uses frag->page to store a temporary index reference while
processing incoming requests. Since frag->page is to become opaque switch
instead to using page_offset. Add a wrapper to tidy this up and propagate the
fact that the indexes are only u16 through the code (this was already true in
practice but unsigned long and in were inconsistently used as variable and
parameter types)
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend. xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off. Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).
This was caused by 47103041e9 (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add xen-backend:vif module alias to the xen-netback module. This allows
automatic loading of the module.
Signed-off-by: Bastian Blank <waldi@debian.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The later causes warnings with gcc 4.5+. __CONST_RING_SIZE was introduced in
667c78afae to fix this but as netback wasn't upstream at the time it did not
benefit, hence:
CC drivers/net/xen-netback/netback.o
drivers/net/xen-netback/netback.c:110:37: warning: variably modified 'grant_copy_op' at file scope [enabled by default]
drivers/net/xen-netback/netback.c:111:30: warning: variably modified 'meta' at file scope [enabled by default]
drivers/net/xen-netback/netback.c: In function 'xen_netbk_rx_action':
drivers/net/xen-netback/netback.c:584:6: warning: variable 'irq' set but not used [-Wunused-but-set-variable]
Thanks to Witold Baryluk for pointing this out.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes error from sparse:
CHECK drivers/net/xen-netback/xenbus.c
drivers/net/xen-netback/xenbus.c:29:40: error: dubious one-bit signed bitfield
int have_hotplug_status_watch:1;
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netback is the host side counterpart to the frontend driver in
drivers/net/xen-netfront.c. The PV protocol is also implemented by
frontend drivers in other OSes too, such as the BSDs and even Windows.
The patch is based on the driver from the xen.git pvops kernel tree but
has been put through the checkpatch.pl wringer plus several manual
cleanup passes and review iterations. The driver has been moved from
drivers/xen/netback to drivers/net/xen-netback.
One major change from xen.git is that the guest transmit path (i.e. what
looks like receive to netback) has been significantly reworked to remove
the dependency on the out of tree PageForeign page flag (a core kernel
patch which enables a per page destructor callback on the final
put_page). This page flag was used in order to implement a grant map
based transmit path (where guest pages are mapped directly into SKB
frags). Instead this version of netback uses grant copy operations into
regular memory belonging to the backend domain. Reinstating the grant
map functionality is something which I would like to revisit in the
future.
Note that this driver depends on 2e820f58f7 "xen/irq: implement
bind_interdomain_evtchn_to_irqhandler for backend drivers" which is in
linux next via the "xen-two" tree and is intended for the 2.6.39 merge
window:
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen.git stable/backends
this branch has only that single commit since 2.6.38-rc2 and is safe for
cross merging into the net branch.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wilfried Klaebe
Zoltan Kiss
Wei Liu
David S. Miller
Paul Durrant
Annie Li
Josh Boyer
Wei Yongjun
Wei Yongjun
Jeff Kirsher
Andy Whitcroft
David Vrabel
Kees Cook
Joe Perches
Dan Carpenter
Jan Beulich
Jason Wang
stephen hemminger
Andrew Jones
Ian Campbell
Matthew Daley
Matt Wilson
Konrad Rzeszutek Wilk
Andres Lagar-Cavilla
Stefano Stabellini
Simon Graham
Linus Torvalds
stephen hemminger
Daniel De Graaf
Michał Mirosław
Eric Dumazet
Bastian Blank
Ian Campbell