This went unnoticed in durin the merge window:
The dsps driver creates a child device for the musb core driver _and_
attaches the of_node to it so devm_usb_get_phy_by_phandle() grabs the
correct phy and attaches the devm resources to the proper device. We
could also use the parent device but then devm would attach the
resource to the wrong device and it would be destroyed once the parent
device is gone - not the device that is used by the musb core driver.
If the phy is now not available then dsps_musb_init() /
devm_usb_get_phy_by_phandle() returns with EPROBE_DEFER. Since the
of_node is attached it tries OF drivers as well and matches the driver
against DSPS. That one creates a new child device for the musb core
driver which gets probed immediately.
The whole thing repeats itself until the stack overflows.
I belive the same problem exists in ux500 glue code (since 313bdb11
("usb: musb: ux500: add device tree probing support") but the drivers are
now probed in the right order so they don't see it.
The problem is that the dsps driver gets bound to the musb-child device
due to the same of_node / matching binding. I don't really agree with
having yet another child node in DT to fix this. Ideally we would have
musb core driver with DT bindings and according to the binding we would
select the few extra hacks / gleue layer.
Therefore I suggest the driver to reject the musb-core device.
Cc: Lee Jones <lee.jones@linaro.org>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The OMAP GPIO controller HW requires a pin to be configured in GPIO
input mode in order to operate as an interrupt input. Since drivers
should not be aware of whether an interrupt pin is also a GPIO or not,
the HW should be fully configured/enabled as an IRQ if a driver solely
uses IRQ APIs such as request_irq(), and never calls any GPIO-related
APIs. As such, add the missing HW setup to the OMAP GPIO controller's
irq_chip driver.
Since this bypasses the GPIO subsystem we have to ensure that another
driver won't be able to request the same GPIO pin that is used as an
IRQ and set its direction as output. Requesting the GPIO and setting
its direction as input is allowed though.
This fixes smsc911x ethernet support for tobi and igep OMAP3 boards
and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO OMAP controller pins can be used as IRQ and GPIO
independently so is necessary to keep track GPIO pins and
IRQ lines usage separately to make sure that the bank will
always be enabled while being used.
Also move gpio_is_input() definition in preparation for the
next patch that setups the controller's irq_chip driver when
a caller requests an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit facd8b80c6
("irq: Sanitize invoke_softirq") converted irq exit
calls of do_softirq() to __do_softirq() on all architectures,
assuming it was only used there for its irq disablement
properties.
But as a side effect, the softirqs processed in the end
of the hardirq are always called on the inline current
stack that is used by irq_exit() instead of the softirq
stack provided by the archs that override do_softirq().
The result is mostly safe if the architecture runs irq_exit()
on a separate irq stack because then softirqs are processed
on that same stack that is near empty at this stage (assuming
hardirq aren't nesting).
Otherwise irq_exit() runs in the task stack and so does the softirq
too. The interrupted call stack can be randomly deep already and
the softirq can dig through it even further. To add insult to the
injury, this softirq can be interrupted by a new hardirq, maximizing
the chances for a stack overrun as reported in powerpc for example:
do_IRQ: stack overflow: 1920
CPU: 0 PID: 1602 Comm: qemu-system-ppc Not tainted 3.10.4-300.1.fc19.ppc64p7 #1
Call Trace:
[c0000000050a8740] .show_stack+0x130/0x200 (unreliable)
[c0000000050a8810] .dump_stack+0x28/0x3c
[c0000000050a8880] .do_IRQ+0x2b8/0x2c0
[c0000000050a8930] hardware_interrupt_common+0x154/0x180
--- Exception: 501 at .cp_start_xmit+0x3a4/0x820 [8139cp]
LR = .cp_start_xmit+0x390/0x820 [8139cp]
[c0000000050a8d40] .dev_hard_start_xmit+0x394/0x640
[c0000000050a8e00] .sch_direct_xmit+0x110/0x260
[c0000000050a8ea0] .dev_queue_xmit+0x260/0x630
[c0000000050a8f40] .br_dev_queue_push_xmit+0xc4/0x130 [bridge]
[c0000000050a8fc0] .br_dev_xmit+0x198/0x270 [bridge]
[c0000000050a9070] .dev_hard_start_xmit+0x394/0x640
[c0000000050a9130] .dev_queue_xmit+0x428/0x630
[c0000000050a91d0] .ip_finish_output+0x2a4/0x550
[c0000000050a9290] .ip_local_out+0x50/0x70
[c0000000050a9310] .ip_queue_xmit+0x148/0x420
[c0000000050a93b0] .tcp_transmit_skb+0x4e4/0xaf0
[c0000000050a94a0] .__tcp_ack_snd_check+0x7c/0xf0
[c0000000050a9520] .tcp_rcv_established+0x1e8/0x930
[c0000000050a95f0] .tcp_v4_do_rcv+0x21c/0x570
[c0000000050a96c0] .tcp_v4_rcv+0x734/0x930
[c0000000050a97a0] .ip_local_deliver_finish+0x184/0x360
[c0000000050a9840] .ip_rcv_finish+0x148/0x400
[c0000000050a98d0] .__netif_receive_skb_core+0x4f8/0xb00
[c0000000050a99d0] .netif_receive_skb+0x44/0x110
[c0000000050a9a70] .br_handle_frame_finish+0x2bc/0x3f0 [bridge]
[c0000000050a9b20] .br_nf_pre_routing_finish+0x2ac/0x420 [bridge]
[c0000000050a9bd0] .br_nf_pre_routing+0x4dc/0x7d0 [bridge]
[c0000000050a9c70] .nf_iterate+0x114/0x130
[c0000000050a9d30] .nf_hook_slow+0xb4/0x1e0
[c0000000050a9e00] .br_handle_frame+0x290/0x330 [bridge]
[c0000000050a9ea0] .__netif_receive_skb_core+0x34c/0xb00
[c0000000050a9fa0] .netif_receive_skb+0x44/0x110
[c0000000050aa040] .napi_gro_receive+0xe8/0x120
[c0000000050aa0c0] .cp_rx_poll+0x31c/0x590 [8139cp]
[c0000000050aa1d0] .net_rx_action+0x1dc/0x310
[c0000000050aa2b0] .__do_softirq+0x158/0x330
[c0000000050aa3b0] .irq_exit+0xc8/0x110
[c0000000050aa430] .do_IRQ+0xdc/0x2c0
[c0000000050aa4e0] hardware_interrupt_common+0x154/0x180
--- Exception: 501 at .bad_range+0x1c/0x110
LR = .get_page_from_freelist+0x908/0xbb0
[c0000000050aa7d0] .list_del+0x18/0x50 (unreliable)
[c0000000050aa850] .get_page_from_freelist+0x908/0xbb0
[c0000000050aa9e0] .__alloc_pages_nodemask+0x21c/0xae0
[c0000000050aaba0] .alloc_pages_vma+0xd0/0x210
[c0000000050aac60] .handle_pte_fault+0x814/0xb70
[c0000000050aad50] .__get_user_pages+0x1a4/0x640
[c0000000050aae60] .get_user_pages_fast+0xec/0x160
[c0000000050aaf10] .__gfn_to_pfn_memslot+0x3b0/0x430 [kvm]
[c0000000050aafd0] .kvmppc_gfn_to_pfn+0x64/0x130 [kvm]
[c0000000050ab070] .kvmppc_mmu_map_page+0x94/0x530 [kvm]
[c0000000050ab190] .kvmppc_handle_pagefault+0x174/0x610 [kvm]
[c0000000050ab270] .kvmppc_handle_exit_pr+0x464/0x9b0 [kvm]
[c0000000050ab320] kvm_start_lightweight+0x1ec/0x1fc [kvm]
[c0000000050ab4f0] .kvmppc_vcpu_run_pr+0x168/0x3b0 [kvm]
[c0000000050ab9c0] .kvmppc_vcpu_run+0xc8/0xf0 [kvm]
[c0000000050aba50] .kvm_arch_vcpu_ioctl_run+0x5c/0x1a0 [kvm]
[c0000000050abae0] .kvm_vcpu_ioctl+0x478/0x730 [kvm]
[c0000000050abc90] .do_vfs_ioctl+0x4ec/0x7c0
[c0000000050abd80] .SyS_ioctl+0xd4/0xf0
[c0000000050abe30] syscall_exit+0x0/0x98
Since this is a regression, this patch proposes a minimalistic
and low-risk solution by blindly forcing the hardirq exit processing of
softirqs on the softirq stack. This way we should reduce significantly
the opportunities for task stack overflow dug by softirqs.
Longer term solutions may involve extending the hardirq stack coverage to
irq_exit(), etc...
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: #3.9.. <stable@vger.kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@au1.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@au1.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Since commit c93bdd0e03 ("netvm: allow skb allocation to use PFMEMALLOC
reserves"), hole size is one bit less than what is written in the comment.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the timer handlers to run after the call to
ipv6_mc_down so use in6_dev_put instead of __in6_dev_put in the
handler function in order to do proper cleanup when the refcnt
reaches 0. Otherwise, the refcnt can reach zero without the
inet6_dev being destroyed and we end up leaking a reference to
the net_device and see messages like the following,
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Tested on linux-3.4.43.
Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the timer handlers to run after the call to
ip_mc_down so use in_dev_put instead of __in_dev_put in the handler
function in order to do proper cleanup when the refcnt reaches 0.
Otherwise, the refcnt can reach zero without the in_device being
destroyed and we end up leaking a reference to the net_device and
see messages like the following,
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Tested on linux-3.4.43.
Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
In this particular case __initdata is incorrect as moxart_mac_driver
can be used after the driver gets initialized.
Also while at it static-ize moxart_mac_driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gre_hlen already accounts for sizeof(struct ipv6_hdr) + gre header,
so initialize max_headroom to zero. Otherwise the
if (encap_limit >= 0) {
max_headroom += 8;
mtu -= 8;
}
increments an uninitialized variable before max_headroom was reset.
Found with coverity: 728539
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 894116bd0e.
I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567
Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:
dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.
The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification. With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are. This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device. Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave. But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error
Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.
This is also needed for the ALLMULTI flag
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP Small Queues was added, we used a sysctl to limit amount of
packets queues on Qdisc/device queues for a given TCP flow.
Problem is this limit is either too big for low rates, or too small
for high rates.
Now TCP stack has rate estimation in sk->sk_pacing_rate, and TSO
auto sizing, it can better control number of packets in Qdisc/device
queues.
New limit is two packets or at least 1 to 2 ms worth of packets.
Low rates flows benefit from this patch by having even smaller
number of packets in queues, allowing for faster recovery,
better RTT estimations.
High rates flows benefit from this patch by allowing more than 2 packets
in flight as we had reports this was a limiting factor to reach line
rate. [ In particular if TX completion is delayed because of coalescing
parameters ]
Example for a single flow on 10Gbp link controlled by FQ/pacing
14 packets in flight instead of 2
$ tc -s -d qd
qdisc fq 8001: dev eth0 root refcnt 32 limit 10000p flow_limit 100p
buckets 1024 quantum 3028 initial_quantum 15140
Sent 1168459366606 bytes 771822841 pkt (dropped 0, overlimits 0
requeues 6822476)
rate 9346Mbit 771713pps backlog 953820b 14p requeues 6822476
2047 flow, 2046 inactive, 1 throttled, delay 15673 ns
2372 gc, 0 highprio, 0 retrans, 9739249 throttled, 0 flows_plimit
Note that sk_pacing_rate is currently set to twice the actual rate, but
this might be refined in the future when a flow is in congestion
avoidance.
Additional change : skb->destructor should be set to tcp_wfree().
A future patch (for linux 3.13+) might remove tcp_limit_output_bytes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few small fixes:
1) Make sure that debugfs entries are removed early enough to prevent
a race.
2) Drop a stray regulator_put from ad8366 left over from the devm_ patches.
3) The ST magnetometer driver had incorrect register addresses for the
actual data channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)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=c+WH
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.12b2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 3.12 cycle (take 2)
A few small fixes:
1) Make sure that debugfs entries are removed early enough to prevent
a race.
2) Drop a stray regulator_put from ad8366 left over from the devm_ patches.
3) The ST magnetometer driver had incorrect register addresses for the
actual data channels.
Commit f95499c303,
n_tty: Don't wait for buffer work in read() loop
creates a race window which can cause a pty master read()
to miss the last pty slave write(s) and return -EIO instead,
thus signalling the pty slave is closed. This can happen when
the pty slave is written and immediately closed but before the
tty buffer i/o loop receives the new input; the pty master
read() is scheduled, sees its read buffer is empty and the
pty slave has been closed, and exits.
Because tty_flush_to_ldisc() has significant performance impact
for parallel i/o, rather than revert the commit, special case this
condition (ie., when the read buffer is empty and the 'other' pty
has been closed) and, only then, wait for buffer work to complete
before re-testing if the read buffer is still empty.
As before, subsequent pty master reads return any available data
until no more data is available, and then returns -EIO to
indicate the pty slave has closed.
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn> (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: Michal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Stable fix for Oopses in the pNFS files layout driver
- Fix a regression when doing a non-exclusive file create on NFSv4.x
- NFSv4.1 security negotiation fixes when looking up the root filesystem
- Fix a memory ordering issue in the pNFS files layout driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ScfI
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.12-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for Oopses in the pNFS files layout driver
- Fix a regression when doing a non-exclusive file create on NFSv4.x
- NFSv4.1 security negotiation fixes when looking up the root
filesystem
- Fix a memory ordering issue in the pNFS files layout driver
* tag 'nfs-for-3.12-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Give "flavor" an initial value to fix a compile warning
NFSv4.1: try SECINFO_NO_NAME flavs until one works
NFSv4.1: Ensure memory ordering between nfs4_ds_connect and nfs4_fl_prepare_ds
NFSv4.1: nfs4_fl_prepare_ds - fix bugs when the connect attempt fails
NFSv4: Honour the 'opened' parameter in the atomic_open() filesystem method
Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
pidns: fix free_pid() to handle the first fork failure
ipc,msg: prevent race with rmid in msgsnd,msgrcv
ipc/sem.c: update sem_otime for all operations
mm/hwpoison: fix the lack of one reference count against poisoned page
mm/hwpoison: fix false report on 2nd attempt at page recovery
mm/hwpoison: fix test for a transparent huge page
mm/hwpoison: fix traversal of hugetlbfs pages to avoid printk flood
block: change config option name for cmdline partition parsing
mm/mlock.c: prevent walking off the end of a pagetable in no-pmd configuration
mm: avoid reinserting isolated balloon pages into LRU lists
arch/parisc/mm/fault.c: fix uninitialized variable usage
include/asm-generic/vtime.h: avoid zero-length file
nilfs2: fix issue with race condition of competition between segments for dirty blocks
Documentation/kernel-parameters.txt: replace kernelcore with Movable
mm/bounce.c: fix a regression where MS_SNAP_STABLE (stable pages snapshotting) was ignored
kernel/kmod.c: check for NULL in call_usermodehelper_exec()
ipc/sem.c: synchronize the proc interface
ipc/sem.c: optimize sem_lock()
ipc/sem.c: fix race in sem_lock()
mm/compaction.c: periodically schedule when freeing pages
...
"case 0" in free_pid() assumes that disable_pid_allocation() should
clear PIDNS_HASH_ADDING before the last pid goes away.
However this doesn't happen if the first fork() fails to create the
child reaper which should call disable_pid_allocation().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a race in both msgrcv() and msgsnd() between finding the msg
and actually dealing with the queue, as another thread can delete shmid
underneath us if we are preempted before acquiring the
kern_ipc_perm.lock.
Manfred illustrates this nicely:
Assume a preemptible kernel that is preempted just after
msq = msq_obtain_object_check(ns, msqid)
in do_msgrcv(). The only lock that is held is rcu_read_lock().
Now the other thread processes IPC_RMID. When the first task is
resumed, then it will happily wait for messages on a deleted queue.
Fix this by checking for if the queue has been deleted after taking the
lock.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reported-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: <stable@vger.kernel.org> [3.11]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 0a2b9d4c79 ("ipc/sem.c: move wake_up_process out of the
spinlock section"), the update of semaphore's sem_otime(last semop time)
was moved to one central position (do_smart_update).
But since do_smart_update() is only called for operations that modify
the array, this means that wait-for-zero semops do not update sem_otime
anymore.
The fix is simple:
Non-alter operations must update sem_otime.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Reported-by: Jia He <jiakernel@gmail.com>
Tested-by: Jia He <jiakernel@gmail.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lack of one reference count against poisoned page for hwpoison_inject
w/o hwpoison_filter enabled result in hwpoison detect -1 users still
referenced the page, however, the number should be 0 except the poison
handler held one after successfully unmap. This patch fix it by hold one
referenced count against poisoned page for hwpoison_inject w/ and w/o
hwpoison_filter enabled.
Before patch:
[ 71.902112] Injecting memory failure at pfn 224706
[ 71.902137] MCE 0x224706: dirty LRU page recovery: Failed
[ 71.902138] MCE 0x224706: dirty LRU page still referenced by -1 users
After patch:
[ 94.710860] Injecting memory failure at pfn 215b68
[ 94.710885] MCE 0x215b68: dirty LRU page recovery: Recovered
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the page is poisoned by software injection w/ MF_COUNT_INCREASED
flag, there is a false report during the 2nd attempt at page recovery
which is not truthful.
This patch fixes it by reporting the first attempt to try free buddy
page recovery if MF_COUNT_INCREASED is set.
Before patch:
[ 346.332041] Injecting memory failure at pfn 200010
[ 346.332189] MCE 0x200010: free buddy, 2nd try page recovery: Delayed
After patch:
[ 297.742600] Injecting memory failure at pfn 200010
[ 297.742941] MCE 0x200010: free buddy page recovery: Delayed
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PageTransHuge() can't guarantee the page is a transparent huge page
since it returns true for both transparent huge and hugetlbfs pages.
This patch fixes it by checking the page is also !hugetlbfs page.
Before patch:
[ 121.571128] Injecting memory failure at pfn 23a200
[ 121.571141] MCE 0x23a200: huge page recovery: Delayed
[ 140.355100] MCE: Memory failure is now running on 0x23a200
After patch:
[ 94.290793] Injecting memory failure at pfn 23a000
[ 94.290800] MCE 0x23a000: huge page recovery: Delayed
[ 105.722303] MCE: Software-unpoisoned page 0x23a000
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
madvise_hwpoison won't check if the page is small page or huge page and
traverses in small page granularity against the range unconditionally,
which result in a printk flood "MCE xxx: already hardware poisoned" if
the page is a huge page.
This patch fixes it by using compound_order(compound_head(page)) for
huge page iterator.
Testcase:
#define _GNU_SOURCE
#include <stdlib.h>
#include <stdio.h>
#include <sys/mman.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <errno.h>
#define PAGES_TO_TEST 3
#define PAGE_SIZE 4096 * 512
int main(void)
{
char *mem;
int i;
mem = mmap(NULL, PAGES_TO_TEST * PAGE_SIZE,
PROT_READ | PROT_WRITE, MAP_PRIVATE | MAP_ANONYMOUS | MAP_HUGETLB, 0, 0);
if (madvise(mem, PAGES_TO_TEST * PAGE_SIZE, MADV_HWPOISON) == -1)
return -1;
munmap(mem, PAGES_TO_TEST * PAGE_SIZE);
return 0;
}
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently commit bab55417b1 ("block: support embedded device command
line partition") introduced CONFIG_CMDLINE_PARSER. However, that name
is too generic and sounds like it enables/disables generic kernel boot
arg processing, when it really is block specific.
Before this option becomes a part of a full/final release, add the BLK_
prefix to it so that it is clear in absence of any other context that it
is block specific.
In addition, fix up the following less critical items:
- help text was not really at all helpful.
- index file for Documentation was not updated
- add the new arg to Documentation/kernel-parameters.txt
- clarify wording in source comments
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Cai Zhiyong <caizhiyong@huawei.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function __munlock_pagevec_fill() introduced in commit 7a8010cd36
("mm: munlock: manual pte walk in fast path instead of
follow_page_mask()") uses pmd_addr_end() for restricting its operation
within current page table.
This is insufficient on architectures/configurations where pmd is folded
and pmd_addr_end() just returns the end of the full range to be walked.
In this case, it allows pte++ to walk off the end of a page table
resulting in unpredictable behaviour.
This patch fixes the function by using pgd_addr_end() and pud_addr_end()
before pmd_addr_end(), which will yield correct page table boundary on
all configurations. This is similar to what existing page walkers do
when walking each level of the page table.
Additionaly, the patch clarifies a comment for get_locked_pte() call in the
function.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Cc: Jörn Engel <joern@logfs.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The FAULT_FLAG_WRITE flag has been set based on uninitialized variable.
Fixes a regression added by commit 759496ba64 ("arch: mm: pass
userspace fault flag to generic fault handler")
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
patch(1) can't handle zero-length files - it appears to simply not create
the file, so my powerpc build fails.
Put something in here to make life easier.
Cc: Hugh Dickins <hughd@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many NILFS2 users were reported about strange file system corruption
(for example):
NILFS: bad btree node (blocknr=185027): level = 0, flags = 0x0, nchildren = 768
NILFS error (device sda4): nilfs_bmap_last_key: broken bmap (inode number=11540)
But such error messages are consequence of file system's issue that takes
place more earlier. Fortunately, Jerome Poulin <jeromepoulin@gmail.com>
and Anton Eliasson <devel@antoneliasson.se> were reported about another
issue not so recently. These reports describe the issue with segctor
thread's crash:
BUG: unable to handle kernel paging request at 0000000000004c83
IP: nilfs_end_page_io+0x12/0xd0 [nilfs2]
Call Trace:
nilfs_segctor_do_construct+0xf25/0x1b20 [nilfs2]
nilfs_segctor_construct+0x17b/0x290 [nilfs2]
nilfs_segctor_thread+0x122/0x3b0 [nilfs2]
kthread+0xc0/0xd0
ret_from_fork+0x7c/0xb0
These two issues have one reason. This reason can raise third issue
too. Third issue results in hanging of segctor thread with eating of
100% CPU.
REPRODUCING PATH:
One of the possible way or the issue reproducing was described by
Jermoe me Poulin <jeromepoulin@gmail.com>:
1. init S to get to single user mode.
2. sysrq+E to make sure only my shell is running
3. start network-manager to get my wifi connection up
4. login as root and launch "screen"
5. cd /boot/log/nilfs which is a ext3 mount point and can log when NILFS dies.
6. lscp | xz -9e > lscp.txt.xz
7. mount my snapshot using mount -o cp=3360839,ro /dev/vgUbuntu/root /mnt/nilfs
8. start a screen to dump /proc/kmsg to text file since rsyslog is killed
9. start a screen and launch strace -f -o find-cat.log -t find
/mnt/nilfs -type f -exec cat {} > /dev/null \;
10. start a screen and launch strace -f -o apt-get.log -t apt-get update
11. launch the last command again as it did not crash the first time
12. apt-get crashes
13. ps aux > ps-aux-crashed.log
13. sysrq+W
14. sysrq+E wait for everything to terminate
15. sysrq+SUSB
Simplified way of the issue reproducing is starting kernel compilation
task and "apt-get update" in parallel.
REPRODUCIBILITY:
The issue is reproduced not stable [60% - 80%]. It is very important to
have proper environment for the issue reproducing. The critical
conditions for successful reproducing:
(1) It should have big modified file by mmap() way.
(2) This file should have the count of dirty blocks are greater that
several segments in size (for example, two or three) from time to time
during processing.
(3) It should be intensive background activity of files modification
in another thread.
INVESTIGATION:
First of all, it is possible to see that the reason of crash is not valid
page address:
NILFS [nilfs_segctor_complete_write]:2100 bh->b_count 0, bh->b_blocknr 13895680, bh->b_size 13897727, bh->b_page 0000000000001a82
NILFS [nilfs_segctor_complete_write]:2101 segbuf->sb_segnum 6783
Moreover, value of b_page (0x1a82) is 6786. This value looks like segment
number. And b_blocknr with b_size values look like block numbers. So,
buffer_head's pointer points on not proper address value.
Detailed investigation of the issue is discovered such picture:
[-----------------------------SEGMENT 6783-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_segctor_do_construct]:2336 nilfs_segctor_assign
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111149024, segbuf->sb_segnum 6783
[-----------------------------SEGMENT 6784-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_lookup_dirty_data_buffers]:782 bh->b_count 1, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_lookup_dirty_data_buffers]:783 bh->b_assoc_buffers.next ffff8802174a6798, bh->b_assoc_buffers.prev ffff880221cffee8
NILFS [nilfs_segctor_do_construct]:2336 nilfs_segctor_assign
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bh]:575 bh->b_count 1, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_segbuf_submit_bh]:576 segbuf->sb_segnum 6784
NILFS [nilfs_segbuf_submit_bh]:577 bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880218bcdf50
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111150080, segbuf->sb_segnum 6784, segbuf->sb_nbio 0
[----------] ditto
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111164416, segbuf->sb_segnum 6784, segbuf->sb_nbio 15
[-----------------------------SEGMENT 6785-------------------------------]
NILFS [nilfs_segctor_do_construct]:2310 nilfs_segctor_begin_construction
NILFS [nilfs_segctor_do_construct]:2321 nilfs_segctor_collect
NILFS [nilfs_lookup_dirty_data_buffers]:782 bh->b_count 2, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_lookup_dirty_data_buffers]:783 bh->b_assoc_buffers.next ffff880219277e80, bh->b_assoc_buffers.prev ffff880221cffc88
NILFS [nilfs_segctor_do_construct]:2367 nilfs_segctor_update_segusage
NILFS [nilfs_segctor_do_construct]:2371 nilfs_segctor_prepare_write
NILFS [nilfs_segctor_do_construct]:2376 nilfs_add_checksums_on_logs
NILFS [nilfs_segctor_do_construct]:2381 nilfs_segctor_write
NILFS [nilfs_segbuf_submit_bh]:575 bh->b_count 2, bh->b_page ffffea000709b000, page->index 0, i_ino 1033103, i_size 25165824
NILFS [nilfs_segbuf_submit_bh]:576 segbuf->sb_segnum 6785
NILFS [nilfs_segbuf_submit_bh]:577 bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880222cc7ee8
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111165440, segbuf->sb_segnum 6785, segbuf->sb_nbio 0
[----------] ditto
NILFS [nilfs_segbuf_submit_bio]:464 bio->bi_sector 111177728, segbuf->sb_segnum 6785, segbuf->sb_nbio 12
NILFS [nilfs_segctor_do_construct]:2399 nilfs_segctor_wait
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6783
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6784
NILFS [nilfs_segbuf_wait]:676 segbuf->sb_segnum 6785
NILFS [nilfs_segctor_complete_write]:2100 bh->b_count 0, bh->b_blocknr 13895680, bh->b_size 13897727, bh->b_page 0000000000001a82
BUG: unable to handle kernel paging request at 0000000000001a82
IP: [<ffffffffa024d0f2>] nilfs_end_page_io+0x12/0xd0 [nilfs2]
Usually, for every segment we collect dirty files in list. Then, dirty
blocks are gathered for every dirty file, prepared for write and
submitted by means of nilfs_segbuf_submit_bh() call. Finally, it takes
place complete write phase after calling nilfs_end_bio_write() on the
block layer. Buffers/pages are marked as not dirty on final phase and
processed files removed from the list of dirty files.
It is possible to see that we had three prepare_write and submit_bio
phases before segbuf_wait and complete_write phase. Moreover, segments
compete between each other for dirty blocks because on every iteration
of segments processing dirty buffer_heads are added in several lists of
payload_buffers:
[SEGMENT 6784]: bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880218bcdf50
[SEGMENT 6785]: bh->b_assoc_buffers.next ffff880218a0d5f8, bh->b_assoc_buffers.prev ffff880222cc7ee8
The next pointer is the same but prev pointer has changed. It means
that buffer_head has next pointer from one list but prev pointer from
another. Such modification can be made several times. And, finally, it
can be resulted in various issues: (1) segctor hanging, (2) segctor
crashing, (3) file system metadata corruption.
FIX:
This patch adds:
(1) setting of BH_Async_Write flag in nilfs_segctor_prepare_write()
for every proccessed dirty block;
(2) checking of BH_Async_Write flag in
nilfs_lookup_dirty_data_buffers() and
nilfs_lookup_dirty_node_buffers();
(3) clearing of BH_Async_Write flag in nilfs_segctor_complete_write(),
nilfs_abort_logs(), nilfs_forget_buffer(), nilfs_clear_dirty_page().
Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Reported-by: Anton Eliasson <devel@antoneliasson.se>
Cc: Paul Fertser <fercerpav@gmail.com>
Cc: ARAI Shun-ichi <hermes@ceres.dti.ne.jp>
Cc: Piotr Szymaniak <szarpaj@grubelek.pl>
Cc: Juan Barry Manuel Canham <Linux@riotingpacifist.net>
Cc: Zahid Chowdhury <zahid.chowdhury@starsolutions.com>
Cc: Elmer Zhang <freeboy6716@gmail.com>
Cc: Kenneth Langga <klangga@gmail.com>
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Han Pingtian found a typo in Documentation/kernel-parameters.txt about
"kernelcore=", that "kernelcore" should be replaced with "Movable" here.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "force" parameter in __blk_queue_bounce was being ignored, which
means that stable page snapshots are not always happening (on ext3).
This of course leads to DIF disks reporting checksum errors, so fix this
regression.
The regression was introduced in commit 6bc454d150 ("bounce: Refactor
__blk_queue_bounce to not use bi_io_vec")
Reported-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If /proc/sys/kernel/core_pattern contains only "|", a NULL pointer
dereference happens upon core dump because argv_split("") returns
argv[0] == NULL.
This bug was once fixed by commit 264b83c07a ("usermodehelper: check
subprocess_info->path != NULL") but was by error reintroduced by commit
7f57cfa4e2 ("usermodehelper: kill the sub_info->path[0] check").
This bug seems to exist since 2.6.19 (the version which core dump to
pipe was added). Depending on kernel version and config, some side
effect might happen immediately after this oops (e.g. kernel panic with
2.6.32-358.18.1.el6).
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The proc interface is not aware of sem_lock(), it instead calls
ipc_lock_object() directly. This means that simple semop() operations
can run in parallel with the proc interface. Right now, this is
uncritical, because the implementation doesn't do anything that requires
a proper synchronization.
But it is dangerous and therefore should be fixed.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Operations that need access to the whole array must guarantee that there
are no simple operations ongoing. Right now this is achieved by
spin_unlock_wait(sem->lock) on all semaphores.
If complex_count is nonzero, then this spin_unlock_wait() is not
necessary, because it was already performed in the past by the thread
that increased complex_count and even though sem_perm.lock was dropped
inbetween, no simple operation could have started, because simple
operations cannot start when complex_count is non-zero.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The exclusion of complex operations in sem_lock() is insufficient: after
acquiring the per-semaphore lock, a simple op must first check that
sem_perm.lock is not locked and only after that test check
complex_count. The current code does it the other way around - and that
creates a race. Details are below.
The patch is a complete rewrite of sem_lock(), based in part on the code
from Mike Galbraith. It removes all gotos and all loops and thus the
risk of livelocks.
I have tested the patch (together with the next one) on my i3 laptop and
it didn't cause any problems.
The bug is probably also present in 3.10 and 3.11, but for these kernels
it might be simpler just to move the test of sma->complex_count after
the spin_is_locked() test.
Details of the bug:
Assume:
- sma->complex_count = 0.
- Thread 1: semtimedop(complex op that must sleep)
- Thread 2: semtimedop(simple op).
Pseudo-Trace:
Thread 1: sem_lock(): acquire sem_perm.lock
Thread 1: sem_lock(): check for ongoing simple ops
Nothing ongoing, thread 2 is still before sem_lock().
Thread 1: try_atomic_semop()
<<< preempted.
Thread 2: sem_lock():
static inline int sem_lock(struct sem_array *sma, struct sembuf *sops,
int nsops)
{
int locknum;
again:
if (nsops == 1 && !sma->complex_count) {
struct sem *sem = sma->sem_base + sops->sem_num;
/* Lock just the semaphore we are interested in. */
spin_lock(&sem->lock);
/*
* If sma->complex_count was set while we were spinning,
* we may need to look at things we did not lock here.
*/
if (unlikely(sma->complex_count)) {
spin_unlock(&sem->lock);
goto lock_array;
}
<<<<<<<<<
<<< complex_count is still 0.
<<<
<<< Here it is preempted
<<<<<<<<<
Thread 1: try_atomic_semop() returns, notices that it must sleep.
Thread 1: increases sma->complex_count.
Thread 1: drops sem_perm.lock
Thread 2:
/*
* Another process is holding the global lock on the
* sem_array; we cannot enter our critical section,
* but have to wait for the global lock to be released.
*/
if (unlikely(spin_is_locked(&sma->sem_perm.lock))) {
spin_unlock(&sem->lock);
spin_unlock_wait(&sma->sem_perm.lock);
goto again;
}
<<< sem_perm.lock already dropped, thus no "goto again;"
locknum = sops->sem_num;
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've been getting warnings about an excessive amount of time spent
allocating pages for migration during memory compaction without
scheduling. isolate_freepages_block() already periodically checks for
contended locks or the need to schedule, but isolate_freepages() never
does.
When a zone is massively long and no suitable targets can be found, this
iteration can be quite expensive without ever doing cond_resched().
Check periodically for the need to reschedule while the compaction free
scanner iterates.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A high setting of max_map_count, and a process core-dumping with a large
enough vm_map_count could result in an NT_FILE note not being written,
and the kernel crashing immediately later because it has assumed
otherwise.
Reproduction of the oops-causing bug described here:
https://lkml.org/lkml/2013/8/30/50
Rge ussue originated in commit 2aa362c49c ("coredump: extend core dump
note section to contain file names of mapped file") from Oct 4, 2012.
This patch make that section optional in that case. fill_files_note()
should signify the error, and also let the info struct in
elf_core_dump() be zero-initialized so that we can check for the
optionally written note.
[akpm@linux-foundation.org: avoid abusing E2BIG, remove a couple of not-really-needed local variables]
[akpm@linux-foundation.org: fix sparse warning]
Signed-off-by: Dan Aloni <alonid@stratoscale.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Tested-by: Martin MOKREJS <mmokrejs@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit cea27eb2a2 ("mm/memory-hotplug: fix lowmem count
overflow when offline pages").
The fixed bug by commit cea27eb was fixed to another way by commit
3dcc0571cd ("mm: correctly update zone->managed_pages"). That commit
enhances memory_hotplug.c to adjust totalhigh_pages when hot-removing
memory, for details please refer to:
http://marc.info/?l=linux-mm&m=136957578620221&w=2
As a result, commit cea27eb2a2 currently causes duplicated decreasing
of totalhigh_pages, thus the revert.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the the debugfs entries in iio_device_unregister(). Otherwise the debugfs
entries might still be accessible even though the device used in the debugfs
callback has already been freed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
fq_reset() should drops all packets in queue, including
throttled flows.
This patch moves code from fq_destroy() to fq_reset()
to do the cleaning.
fq_change() must stop calling fq_dequeue() if all remaining
packets are from throttled flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8ed781668d ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.
This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the scenario where an IPv6 router is advertising a fixed
preferred_lft of 1800 seconds, while the valid_lft begins at 3600
seconds and counts down in realtime.
A client should reset its preferred_lft to 1800 every time the RA is
received, but a bug is causing Linux to ignore the update.
The core problem is here:
if (prefered_lft != ifp->prefered_lft) {
Note that ifp->prefered_lft is an offset, so it doesn't decrease over
time. Thus, the comparison is always (1800 != 1800), which fails to
trigger an update.
The most direct solution would be to compute a "stored_prefered_lft",
and use that value in the comparison. But I think that trying to filter
out unnecessary updates here is a premature optimization. In order for
the filter to apply, both of these would need to hold:
- The advertised valid_lft and preferred_lft are both declining in
real time.
- No clock skew exists between the router & client.
So in this patch, I've set "update_lft = 1" unconditionally, which
allows the surrounding code to be greatly simplified.
Signed-off-by: Paul Marks <pmarks@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Andrzej Siewior
Javier Martinez Canillas
Frederic Weisbecker
Nicolas Dichtel
David S. Miller
Salam Noureddine
Bartlomiej Zolnierkiewicz
Hannes Frederic Sowa
Aida Mynzhasova
Neil Horman
Eric Dumazet
Greg Kroah-Hartman
Peter Hurley
Michal Malý
Arnaud Ebalard
Linus Torvalds
Peter Korsgaard
Oleg Nesterov
Davidlohr Bueso
Manfred Spraul
Wanpeng Li
Paul Gortmaker
Vlastimil Babka
Rafael Aquini
Felipe Pena
Andrew Morton
Vyacheslav Dubeyko
Weiping Pan
Darrick J. Wong
Tetsuo Handa
David Rientjes
Dan Aloni
Joonyoung Shim
Denis CIOCCA
Lars-Peter Clausen
Wei Liu
Paul Durrant
Paul Marks