This change adds support for a new ptrace option, PTRACE_O_TRACESECCOMP,
and a new return value for seccomp BPF programs, SECCOMP_RET_TRACE.
When a tracer specifies the PTRACE_O_TRACESECCOMP ptrace option, the
tracer will be notified, via PTRACE_EVENT_SECCOMP, for any syscall that
results in a BPF program returning SECCOMP_RET_TRACE. The 16-bit
SECCOMP_RET_DATA mask of the BPF program return value will be passed as
the ptrace_message and may be retrieved using PTRACE_GETEVENTMSG.
If the subordinate process is not using seccomp filter, then no
system call notifications will occur even if the option is specified.
If there is no tracer with PTRACE_O_TRACESECCOMP when SECCOMP_RET_TRACE
is returned, the system call will not be executed and an -ENOSYS errno
will be returned to userspace.
This change adds a dependency on the system call slow path. Any future
efforts to use the system call fast path for seccomp filter will need to
address this restriction.
Signed-off-by: Will Drewry <wad@chromium.org>
Acked-by: Eric Paris <eparis@redhat.com>
v18: - rebase
- comment fatal_signal check
- acked-by
- drop secure_computing_int comment
v17: - ...
v16: - update PT_TRACE_MASK to 0xbf4 so that STOP isn't clear on SETOPTIONS call (indan@nul.nu)
[note PT_TRACE_MASK disappears in linux-next]
v15: - add audit support for non-zero return codes
- clean up style (indan@nul.nu)
v14: - rebase/nochanges
v13: - rebase on to 88ebdda615
(Brings back a change to ptrace.c and the masks.)
v12: - rebase to linux-next
- use ptrace_event and update arch/Kconfig to mention slow-path dependency
- drop all tracehook changes and inclusion (oleg@redhat.com)
v11: - invert the logic to just make it a PTRACE_SYSCALL accelerator
(indan@nul.nu)
v10: - moved to PTRACE_O_SECCOMP / PT_TRACE_SECCOMP
v9: - n/a
v8: - guarded PTRACE_SECCOMP use with an ifdef
v7: - introduced
Signed-off-by: James Morris <james.l.morris@oracle.com>
"[RFC - PATCH 0/7] consolidation of BUG support code."
https://lkml.org/lkml/2012/1/26/525
--
The changes shown here are to unify linux's BUG support under
the one <linux/bug.h> file. Due to historical reasons, we have
some BUG code in bug.h and some in kernel.h -- i.e. the support for
BUILD_BUG in linux/kernel.h predates the addition of linux/bug.h,
but old code in kernel.h wasn't moved to bug.h at that time. As
a band-aid, kernel.h was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions.
Here is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.]
Ugh - very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and
hence relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2.
But to ensure that git history for bisect doesn't get needless
build failures introduced, the commits have been reorderd to fix
the problem areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PYQT
-----END PGP SIGNATURE-----
Merge tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/bug.h> cleanup from Paul Gortmaker:
"The changes shown here are to unify linux's BUG support under the one
<linux/bug.h> file. Due to historical reasons, we have some BUG code
in bug.h and some in kernel.h -- i.e. the support for BUILD_BUG in
linux/kernel.h predates the addition of linux/bug.h, but old code in
kernel.h wasn't moved to bug.h at that time. As a band-aid, kernel.h
was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions. Here
is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.] Ugh -
very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and hence
relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2. But
to ensure that git history for bisect doesn't get needless build
failures introduced, the commits have been reorderd to fix the problem
areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414"
Fix up conflicts (new radeon file, reiserfs header cleanups) as per Paul
and linux-next.
* tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
kernel.h: doesn't explicitly use bug.h, so don't include it.
bug: consolidate BUILD_BUG_ON with other bug code
BUG: headers with BUG/BUG_ON etc. need linux/bug.h
bug.h: add include of it to various implicit C users
lib: fix implicit users of kernel.h for TAINT_WARN
spinlock: macroize assert_spin_locked to avoid bug.h dependency
x86: relocate get/set debugreg fcns to include/asm/debugreg.
PTRACE_SEIZE code is tested and ready for production use, remove the
code which requires special bit in data argument to make PTRACE_SEIZE
work.
Strace team prepares for a new release of strace, and we would like to
ship the code which uses PTRACE_SEIZE, preferably after this change goes
into released kernel.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PTRACE_EVENT_foo and PTRACE_O_TRACEfoo used to match.
New PTRACE_EVENT_STOP is the first event which has no corresponding
PTRACE_O_TRACE option. If we will ever want to add another such option,
its PTRACE_EVENT's value will collide with PTRACE_EVENT_STOP's value.
This patch changes PTRACE_EVENT_STOP value to prevent this.
While at it, added a comment - the one atop PTRACE_EVENT block, saying
"Wait extended result codes for the above trace options", is not true
for PTRACE_EVENT_STOP.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Exchange PT_TRACESYSGOOD and PT_PTRACE_CAP bit positions, which makes
PT_option bits contiguous and therefore makes code in
ptrace_setoptions() much simpler.
Every PTRACE_O_TRACEevent is defined to (1 << PTRACE_EVENT_event)
instead of using explicit numeric constants, to ensure we don't mess up
relationship between bit positions and event ids.
PT_EVENT_FLAG_SHIFT was not particularly useful, PT_OPT_FLAG_SHIFT with
value of PT_EVENT_FLAG_SHIFT-1 is easier to use.
PT_TRACE_MASK constant is nuked, the only its use is replaced by
(PTRACE_O_MASK << PT_OPT_FLAG_SHIFT).
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ptrace_event(PTRACE_EVENT_EXEC) sends SIGTRAP if PT_TRACE_EXEC is not
set. This is because this SIGTRAP predates PTRACE_O_TRACEEXEC option,
we do not need/want this with PT_SEIZED which can set the options during
attach.
Suggested-by: Pedro Alves <palves@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Chris Evans <scarybeasts@gmail.com>
Cc: Indan Zupancic <indan@nul.nu>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a header file is making use of BUG, BUG_ON, BUILD_BUG_ON, or any
other BUG variant in a static inline (i.e. not in a #define) then
that header really should be including <linux/bug.h> and not just
expecting it to be implicitly present.
We can make this change risk-free, since if the files using these
headers didn't have exposure to linux/bug.h already, they would have
been causing compile failures/warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
audit: no leading space in audit_log_d_path prefix
audit: treat s_id as an untrusted string
audit: fix signedness bug in audit_log_execve_info()
audit: comparison on interprocess fields
audit: implement all object interfield comparisons
audit: allow interfield comparison between gid and ogid
audit: complex interfield comparison helper
audit: allow interfield comparison in audit rules
Kernel: Audit Support For The ARM Platform
audit: do not call audit_getname on error
audit: only allow tasks to set their loginuid if it is -1
audit: remove task argument to audit_set_loginuid
audit: allow audit matching on inode gid
audit: allow matching on obj_uid
audit: remove audit_finish_fork as it can't be called
audit: reject entry,always rules
audit: inline audit_free to simplify the look of generic code
audit: drop audit_set_macxattr as it doesn't do anything
audit: inline checks for not needing to collect aux records
audit: drop some potentially inadvisable likely notations
...
Use evil merge to fix up grammar mistakes in Kconfig file.
Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.
The audit system previously expected arches calling to audit_syscall_exit to
supply as arguments if the syscall was a success and what the return code was.
Audit also provides a helper AUDITSC_RESULT which was supposed to simplify things
by converting from negative retcodes to an audit internal magic value stating
success or failure. This helper was wrong and could indicate that a valid
pointer returned to userspace was a failed syscall. The fix is to fix the
layering foolishness. We now pass audit_syscall_exit a struct pt_reg and it
in turns calls back into arch code to collect the return value and to
determine if the syscall was a success or failure. We also define a generic
is_syscall_success() macro which determines success/failure based on if the
value is < -MAX_ERRNO. This works for arches like x86 which do not use a
separate mechanism to indicate syscall failure.
We make both the is_syscall_success() and regs_return_value() static inlines
instead of macros. The reason is because the audit function must take a void*
for the regs. (uml calls theirs struct uml_pt_regs instead of just struct
pt_regs so audit_syscall_exit can't take a struct pt_regs). Since the audit
function takes a void* we need to use static inlines to cast it back to the
arch correct structure to dereference it.
The other major change is that on some arches, like ia64, MIPS and ppc, we
change regs_return_value() to give us the negative value on syscall failure.
THE only other user of this macro, kretprobe_example.c, won't notice and it
makes the value signed consistently for the audit functions across all archs.
In arch/sh/kernel/ptrace_64.c I see that we were using regs[9] in the old
audit code as the return value. But the ptrace_64.h code defined the macro
regs_return_value() as regs[3]. I have no idea which one is correct, but this
patch now uses the regs_return_value() function, so it now uses regs[3].
For powerpc we previously used regs->result but now use the
regs_return_value() function which uses regs->gprs[3]. regs->gprs[3] is
always positive so the regs_return_value(), much like ia64 makes it negative
before calling the audit code when appropriate.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com> [for x86 portion]
Acked-by: Tony Luck <tony.luck@intel.com> [for ia64]
Acked-by: Richard Weinberger <richard@nod.at> [for uml]
Acked-by: David S. Miller <davem@davemloft.net> [for sparc]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [for mips]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [for ppc]
Reading /proc/pid/stat of another process checks if one has ptrace permissions
on that process. If one does have permissions it outputs some data about the
process which might have security and attack implications. If the current
task does not have ptrace permissions the read still works, but those fields
are filled with inocuous (0) values. Since this check and a subsequent denial
is not a violation of the security policy we should not audit such denials.
This can be quite useful to removing ptrace broadly across a system without
flooding the logs when ps is run or something which harmlessly walks proc.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
The fake SIGSTOP during attach has numerous problems. PTRACE_SEIZE
is already fine, but we have basically the same problems is SIGSTOP
is sent on auto-attach, the tracer can't know if this signal signal
should be cancelled or not.
Change ptrace_event() to set JOBCTL_TRAP_STOP if the new child is
PT_SEIZED, this triggers the PTRACE_EVENT_STOP report.
Thereafter a PT_SEIZED task can never report the bogus SIGSTOP.
Test-case:
#define PTRACE_SEIZE 0x4206
#define PTRACE_SEIZE_DEVEL 0x80000000
#define PTRACE_EVENT_STOP 7
#define WEVENT(s) ((s & 0xFF0000) >> 16)
int main(void)
{
int child, grand_child, status;
long message;
child = fork();
if (!child) {
kill(getpid(), SIGSTOP);
fork();
assert(0);
return 0x23;
}
assert(ptrace(PTRACE_SEIZE, child, 0,PTRACE_SEIZE_DEVEL) == 0);
assert(wait(&status) == child);
assert(WIFSTOPPED(status) && WSTOPSIG(status) == SIGSTOP);
assert(ptrace(PTRACE_SETOPTIONS, child, 0, PTRACE_O_TRACEFORK) == 0);
assert(ptrace(PTRACE_CONT, child, 0,0) == 0);
assert(waitpid(child, &status, 0) == child);
assert(WIFSTOPPED(status) && WSTOPSIG(status) == SIGTRAP);
assert(WEVENT(status) == PTRACE_EVENT_FORK);
assert(ptrace(PTRACE_GETEVENTMSG, child, 0, &message) == 0);
grand_child = message;
assert(waitpid(grand_child, &status, 0) == grand_child);
assert(WIFSTOPPED(status) && WSTOPSIG(status) == SIGTRAP);
assert(WEVENT(status) == PTRACE_EVENT_STOP);
kill(child, SIGKILL);
kill(grand_child, SIGKILL);
return 0;
}
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
If the new child is traced, do_fork() adds the pending SIGSTOP.
It assumes that either it is traced because of auto-attach or the
tracer attached later, in both cases sigaddset/set_thread_flag is
correct even if SIGSTOP is already pending.
Now that we have PTRACE_SEIZE this is no longer right in the latter
case. If the tracer does PTRACE_SEIZE after copy_process() makes the
child visible the queued SIGSTOP is wrong.
We could check PT_SEIZED bit and change ptrace_attach() to set both
PT_PTRACED and PT_SEIZED bits simultaneously but see the next patch,
we need to know whether this child was auto-attached or not anyway.
So this patch simply moves this code to ptrace_init_task(), this
way we can never race with ptrace_attach().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
new_child->jobctl is not initialized during the fork, it is copied
from parent->jobctl. Currently this is harmless, the forking task
is running and copy_process() can't succeed if signal_pending() is
true, so only JOBCTL_STOP_DEQUEUED can be copied. Still this is a
bit fragile, it would be more clean to set ->jobctl = 0 explicitly.
Also, check ->ptrace != 0 instead of PT_PTRACED, move the
CONFIG_HAVE_HW_BREAKPOINT code up.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
ptrace_reparented() naively does parent != real_parent, this means
it returns true even if the tracer _is_ the real parent. This is per
process thing, not per-thread. The only reason ->real_parent can
point to the non-leader thread is that we have __WNOTHREAD.
Change it to check !same_thread_group(parent, real_parent).
It has two callers, and in both cases the current check does not
look right.
exit_notify: we should respect ->exit_signal if the exiting leader
is traced by any thread from the parent thread group. It is the
child of the whole group, and we are going to send the signal to
the whole group.
wait_task_zombie: without __WNOTHREAD do_wait() should do the same
for any thread, only sys_ptrace() is "bound" to the single thread.
However do_wait(WEXITED) succeeds but does not release a traced
natural child unless the caller is the tracer.
Test-case:
void *tfunc(void *arg)
{
assert(ptrace(PTRACE_ATTACH, (long)arg, 0,0) == 0);
pause();
return NULL;
}
int main(void)
{
pthread_t thr;
pid_t pid, stat, ret;
pid = fork();
if (!pid) {
pause();
assert(0);
}
assert(pthread_create(&thr, NULL, tfunc, (void*)(long)pid) == 0);
assert(waitpid(-1, &stat, 0) == pid);
assert(WIFSTOPPED(stat));
kill(pid, SIGKILL);
assert(waitpid(-1, &stat, 0) == pid);
assert(WIFSIGNALED(stat) && WTERMSIG(stat) == SIGKILL);
ret = waitpid(pid, &stat, 0);
if (ret < 0)
return 0;
printf("WTF? %d is dead, but: wait=%d stat=%x\n",
pid, ret, stat);
return 1;
}
Note that the main thread simply does
pid = fork();
kill(pid, SIGKILL);
and then without the patch wait4(WEXITED) succeeds twice and reports
WTERMSIG(stat) == SIGKILL.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
tracehook.h is on the way out. Rename tracehook_tracer_task() to
ptrace_parent() and move it from tracehook.h to ptrace.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Move SIGTRAP on exec(2) logic from tracehook_report_exec() to
ptrace_event(). This is part of changes to make ptrace_event()
smarter and handle ptrace event related details in one place.
This doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
This patch implements ptrace_event_enabled() which tests whether a
given PTRACE_EVENT_* is enabled and use it to simplify ptrace_event()
and tracehook_prepare_clone().
PT_EVENT_FLAG() macro is added which calculates PT_TRACE_* flag from
PTRACE_EVENT_*. This is used to define PT_TRACE_* flags and by
ptrace_event_enabled() to find the matching flag.
This is used to make ptrace_event() and tracehook_prepare_clone()
simpler.
* ptrace_event() callers were responsible for providing mask to test
whether the event was enabled. This patch implements
ptrace_event_enabled() and make ptrace_event() drop @mask and
determine whether the event is enabled from @event. Note that
@event is constant and this conversion doesn't add runtime overhead.
All conversions except tracehook_report_clone_complete() are
trivial. tracehook_report_clone_complete() used to use 0 for @mask
(always enabled) but now tests whether the specified event is
enabled. This doesn't cause any behavior difference as it's
guaranteed that the event specified by @trace is enabled.
* tracehook_prepare_clone() now only determines which event is
applicable and use ptrace_event_enabled() for enable test.
This doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
task_ptrace(task) simply dereferences task->ptrace and isn't even used
consistently only adding confusion. Kill it and directly access
->ptrace instead.
This doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
The previous patch implemented async notification for ptrace but it
only worked while trace is running. This patch introduces
PTRACE_LISTEN which is suggested by Oleg Nestrov.
It's allowed iff tracee is in STOP trap and puts tracee into
quasi-running state - tracee never really runs but wait(2) and
ptrace(2) consider it to be running. While ptracer is listening,
tracee is allowed to re-enter STOP to notify an async event.
Listening state is cleared on the first notification. Ptracer can
also clear it by issuing INTERRUPT - tracee will re-trap into STOP
with listening state cleared.
This allows ptracer to monitor group stop state without running tracee
- use INTERRUPT to put tracee into STOP trap, issue LISTEN and then
wait(2) to wait for the next group stop event. When it happens,
PTRACE_GETSIGINFO provides information to determine the current state.
Test program follows.
#define PTRACE_SEIZE 0x4206
#define PTRACE_INTERRUPT 0x4207
#define PTRACE_LISTEN 0x4208
#define PTRACE_SEIZE_DEVEL 0x80000000
static const struct timespec ts1s = { .tv_sec = 1 };
int main(int argc, char **argv)
{
pid_t tracee, tracer;
int i;
tracee = fork();
if (!tracee)
while (1)
pause();
tracer = fork();
if (!tracer) {
siginfo_t si;
ptrace(PTRACE_SEIZE, tracee, NULL,
(void *)(unsigned long)PTRACE_SEIZE_DEVEL);
ptrace(PTRACE_INTERRUPT, tracee, NULL, NULL);
repeat:
waitid(P_PID, tracee, NULL, WSTOPPED);
ptrace(PTRACE_GETSIGINFO, tracee, NULL, &si);
if (!si.si_code) {
printf("tracer: SIG %d\n", si.si_signo);
ptrace(PTRACE_CONT, tracee, NULL,
(void *)(unsigned long)si.si_signo);
goto repeat;
}
printf("tracer: stopped=%d signo=%d\n",
si.si_signo != SIGTRAP, si.si_signo);
if (si.si_signo != SIGTRAP)
ptrace(PTRACE_LISTEN, tracee, NULL, NULL);
else
ptrace(PTRACE_CONT, tracee, NULL, NULL);
goto repeat;
}
for (i = 0; i < 3; i++) {
nanosleep(&ts1s, NULL);
printf("mother: SIGSTOP\n");
kill(tracee, SIGSTOP);
nanosleep(&ts1s, NULL);
printf("mother: SIGCONT\n");
kill(tracee, SIGCONT);
}
nanosleep(&ts1s, NULL);
kill(tracer, SIGKILL);
kill(tracee, SIGKILL);
return 0;
}
This is identical to the program to test TRAP_NOTIFY except that
tracee is PTRACE_LISTEN'd instead of PTRACE_CONT'd when group stopped.
This allows ptracer to monitor when group stop ends without running
tracee.
# ./test-listen
tracer: stopped=0 signo=5
mother: SIGSTOP
tracer: SIG 19
tracer: stopped=1 signo=19
mother: SIGCONT
tracer: stopped=0 signo=5
tracer: SIG 18
mother: SIGSTOP
tracer: SIG 19
tracer: stopped=1 signo=19
mother: SIGCONT
tracer: stopped=0 signo=5
tracer: SIG 18
mother: SIGSTOP
tracer: SIG 19
tracer: stopped=1 signo=19
mother: SIGCONT
tracer: stopped=0 signo=5
tracer: SIG 18
-v2: Moved JOBCTL_LISTENING check in wait_task_stopped() into
task_stopped_code() as suggested by Oleg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Currently, there's no way to trap a running ptracee short of sending a
signal which has various side effects. This patch implements
PTRACE_INTERRUPT which traps ptracee without any signal or job control
related side effect.
The implementation is almost trivial. It uses the group stop trap -
SIGTRAP | PTRACE_EVENT_STOP << 8. A new trap flag
JOBCTL_TRAP_INTERRUPT is added, which is set on PTRACE_INTERRUPT and
cleared when any trap happens. As INTERRUPT should be useable
regardless of the current state of tracee, task_is_traced() test in
ptrace_check_attach() is skipped for INTERRUPT.
PTRACE_INTERRUPT is available iff tracee is attached with
PTRACE_SEIZE.
Test program follows.
#define PTRACE_SEIZE 0x4206
#define PTRACE_INTERRUPT 0x4207
#define PTRACE_SEIZE_DEVEL 0x80000000
static const struct timespec ts100ms = { .tv_nsec = 100000000 };
static const struct timespec ts1s = { .tv_sec = 1 };
static const struct timespec ts3s = { .tv_sec = 3 };
int main(int argc, char **argv)
{
pid_t tracee;
tracee = fork();
if (tracee == 0) {
nanosleep(&ts100ms, NULL);
while (1) {
printf("tracee: alive pid=%d\n", getpid());
nanosleep(&ts1s, NULL);
}
}
if (argc > 1)
kill(tracee, SIGSTOP);
nanosleep(&ts100ms, NULL);
ptrace(PTRACE_SEIZE, tracee, NULL,
(void *)(unsigned long)PTRACE_SEIZE_DEVEL);
if (argc > 1) {
waitid(P_PID, tracee, NULL, WSTOPPED);
ptrace(PTRACE_CONT, tracee, NULL, NULL);
}
nanosleep(&ts3s, NULL);
printf("tracer: INTERRUPT and DETACH\n");
ptrace(PTRACE_INTERRUPT, tracee, NULL, NULL);
waitid(P_PID, tracee, NULL, WSTOPPED);
ptrace(PTRACE_DETACH, tracee, NULL, NULL);
nanosleep(&ts3s, NULL);
printf("tracer: exiting\n");
kill(tracee, SIGKILL);
return 0;
}
When called without argument, tracee is seized from running state,
interrupted and then detached back to running state.
# ./test-interrupt
tracee: alive pid=4546
tracee: alive pid=4546
tracee: alive pid=4546
tracer: INTERRUPT and DETACH
tracee: alive pid=4546
tracee: alive pid=4546
tracee: alive pid=4546
tracer: exiting
When called with argument, tracee is seized from stopped state,
continued, interrupted and then detached back to stopped state.
# ./test-interrupt 1
tracee: alive pid=4548
tracee: alive pid=4548
tracee: alive pid=4548
tracer: INTERRUPT and DETACH
tracer: exiting
Before PTRACE_INTERRUPT, once the tracee was running, there was no way
to trap tracee and do PTRACE_DETACH without causing side effect.
-v2: Updated to use task_set_jobctl_pending() so that it doesn't end
up scheduling TRAP_STOP if child is dying which may make the
child unkillable. Spotted by Oleg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
PTRACE_ATTACH implicitly issues SIGSTOP on attach which has side
effects on tracee signal and job control states. This patch
implements a new ptrace request PTRACE_SEIZE which attaches a tracee
without trapping it or affecting its signal and job control states.
The usage is the same with PTRACE_ATTACH but it takes PTRACE_SEIZE_*
flags in @data. Currently, the only defined flag is
PTRACE_SEIZE_DEVEL which is a temporary flag to enable PTRACE_SEIZE.
PTRACE_SEIZE will change ptrace behaviors outside of attach itself.
The changes will be implemented gradually and the DEVEL flag is to
prevent programs which expect full SEIZE behavior from using it before
all the behavior modifications are complete while allowing unit
testing. The flag will be removed once SEIZE behaviors are completely
implemented.
* PTRACE_SEIZE, unlike ATTACH, doesn't force tracee to trap. After
attaching tracee continues to run unless a trap condition occurs.
* PTRACE_SEIZE doesn't affect signal or group stop state.
* If PTRACE_SEIZE'd, group stop uses PTRACE_EVENT_STOP trap which uses
exit_code of (signr | PTRACE_EVENT_STOP << 8) where signr is one of
the stopping signals if group stop is in effect or SIGTRAP
otherwise, and returns usual trap siginfo on PTRACE_GETSIGINFO
instead of NULL.
Seizing sets PT_SEIZED in ->ptrace of the tracee. This flag will be
used to determine whether new SEIZE behaviors should be enabled.
Test program follows.
#define PTRACE_SEIZE 0x4206
#define PTRACE_SEIZE_DEVEL 0x80000000
static const struct timespec ts100ms = { .tv_nsec = 100000000 };
static const struct timespec ts1s = { .tv_sec = 1 };
static const struct timespec ts3s = { .tv_sec = 3 };
int main(int argc, char **argv)
{
pid_t tracee;
tracee = fork();
if (tracee == 0) {
nanosleep(&ts100ms, NULL);
while (1) {
printf("tracee: alive\n");
nanosleep(&ts1s, NULL);
}
}
if (argc > 1)
kill(tracee, SIGSTOP);
nanosleep(&ts100ms, NULL);
ptrace(PTRACE_SEIZE, tracee, NULL,
(void *)(unsigned long)PTRACE_SEIZE_DEVEL);
if (argc > 1) {
waitid(P_PID, tracee, NULL, WSTOPPED);
ptrace(PTRACE_CONT, tracee, NULL, NULL);
}
nanosleep(&ts3s, NULL);
printf("tracer: exiting\n");
return 0;
}
When the above program is called w/o argument, tracee is seized while
running and remains running. When tracer exits, tracee continues to
run and print out messages.
# ./test-seize-simple
tracee: alive
tracee: alive
tracee: alive
tracer: exiting
tracee: alive
tracee: alive
When called with an argument, tracee is seized from stopped state and
continued, and returns to stopped state when tracer exits.
# ./test-seize
tracee: alive
tracee: alive
tracee: alive
tracer: exiting
# ps -el|grep test-seize
1 T 0 4720 1 0 80 0 - 941 signal ttyS0 00:00:00 test-seize
-v2: SEIZE doesn't schedule TRAP_STOP and leaves tracee running as Jan
suggested.
-v3: PTRACE_EVENT_STOP traps now report group stop state by signr. If
group stop is in effect the stop signal number is returned as
part of exit_code; otherwise, SIGTRAP. This was suggested by
Denys and Oleg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
PTRACE_INTERRUPT is going to be added which should also skip
task_is_traced() check in ptrace_check_attach(). Rename @kill to
@ignore_state and make it bool. Add function comment while at it.
This patch doesn't introduce any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
When a task is traced and is in a stopped state, the tracer
may execute a ptrace request to examine the tracee state and
get its task struct. Right after, the tracee can be killed
and thus its breakpoints released.
This can happen concurrently when the tracer is in the middle
of reading or modifying these breakpoints, leading to dereferencing
a freed pointer.
Hence, to prepare the fix, create a generic breakpoint reference
holding API. When a reference on the breakpoints of a task is
held, the breakpoints won't be released until the last reference
is dropped. After that, no more ptrace request on the task's
breakpoints can be serviced for the tracer.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: v2.6.33.. <stable@kernel.org>
Link: http://lkml.kernel.org/r/1302284067-7860-2-git-send-email-fweisbec@gmail.com
They are only used inside kernel/ptrace.c, and have been for a long
time. We don't want to go back to the bad-old-days when architectures
did things on their own, so make them static and private.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since userspace API of ptrace syscall defines @addr and @data as void
pointers, it would be more appropriate to define them as unsigned long in
kernel. Therefore related functions are changed also.
'unsigned long' is typically used in other places in kernel as an opaque
data type and that using this helps cleaning up a lot of warnings from
sparse.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support for the PMU's BTS features has been upstreamed in
v2.6.32, but we still have the old and disabled ptrace-BTS,
as Linus noticed it not so long ago.
It's buggy: TIF_DEBUGCTLMSR is trampling all over that MSR without
regard for other uses (perf) and doesn't provide the flexibility
needed for perf either.
Its users are ptrace-block-step and ptrace-bts, since ptrace-bts
was never used and ptrace-block-step can be implemented using a
much simpler approach.
So axe all 3000 lines of it. That includes the *locked_memory*()
APIs in mm/mlock.c as well.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Markus Metzger <markus.t.metzger@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <20100325135413.938004390@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While in theory user_enable_single_step/user_disable_single_step/
user_enable_blockstep could also be provided as an inline or macro there's
no good reason to do so, and having the prototype in one places keeps code
size and confusion down.
Roland said:
The original thought there was that user_enable_single_step() et al
might well be only an instruction or three on a sane machine (as if we
have any of those!), and since there is only one call site inlining
would be beneficial. But I agree that there is no strong reason to care
about inlining it.
As to the arch changes, there is only one thought I'd add to the
record. It was always my thinking that for an arch where
PTRACE_SINGLESTEP does text-modifying breakpoint insertion,
user_enable_single_step() should not be provided. That is,
arch_has_single_step()=>true means that there is an arch facility with
"pure" semantics that does not have any unexpected side effects.
Inserting a breakpoint might do very unexpected strange things in
multi-threaded situations. Aside from that, it is a peculiar side
effect that user_{enable,disable}_single_step() should cause COW
de-sharing of text pages and so forth. For PTRACE_SINGLESTEP, all these
peculiarities are the status quo ante for that arch, so having
arch_ptrace() itself do those is one thing. But for building other
things in the future, it is nicer to have a uniform "pure" semantics
that arch-independent code can expect.
OTOH, all such arch issues are really up to the arch maintainer. As
of today, there is nothing but ptrace using user_enable_single_step() et
al so it's a distinction without a practical difference. If/when there
are other facilities that use user_enable_single_step() and might care,
the affected arch's can revisit the question when someone cares about
the quality of the arch support for said new facility.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return -EINVAL for the bad size and for unrecognized NT_* type in
ptrace_regset() instead of -EIO.
Also update the comments for this ptrace interface with more clarifications.
Requested-by: Roland McGrath <roland@redhat.com>
Requested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100222225240.397523600@sbs-t61.sc.intel.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Generic support for PTRACE_GETREGSET/PTRACE_SETREGSET commands which
export the regsets supported by each architecture using the correponding
NT_* types. These NT_* types are already part of the userland ABI, used
in representing the architecture specific register sets as different NOTES
in an ELF core file.
'addr' parameter for the ptrace system call encode the REGSET type (using
the corresppnding NT_* type) and the 'data' parameter points to the
struct iovec having the user buffer and the length of that buffer.
struct iovec iov = { buf, len};
ret = ptrace(PTRACE_GETREGSET/PTRACE_SETREGSET, pid, NT_XXX_TYPE, &iov);
On successful completion, iov.len will be updated by the kernel specifying
how much the kernel has written/read to/from the user's iov.buf.
x86 extended state registers are primarily exported using this interface.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100211195614.886724710@sbs-t61.sc.intel.com>
Acked-by: Hongjiu Lu <hjl.tools@gmail.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Suggested by Roland.
Currently there is no way to synthesize a single-stepping trap in the
arch-independent manner. This patch adds the default helper which fills
siginfo_t, arch/ can can override it.
Architetures which implement user_enable_single_step() should add
user_single_step_siginfo() also.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes.
ptrace_init_task() looks confusing, as if we always auto-attach when "bool
ptrace" argument is true, while in fact we attach only if current is
traced.
Make the code more explicit and kill now unused ptrace_link().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use rcu_read_lock() instead of tasklist_lock to find/get the task
in ptrace_get_task_struct().
- Make it static, it has no callers outside of ptrace.c.
- The comment doesn't match the reality, this helper does not do
any checks. Beacuse it is really trivial and static I removed the
whole comment.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the ptrace bts context field to task_struct unconditionally.
Initialize the field directly in copy_process().
Remove all the unneeded functionality used to initialize that field.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144603.292754000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
By discussion with Roland.
- Rename ptrace_exit() to exit_ptrace(), and change it to do all the
necessary work with ->ptraced list by its own.
- Move this code from exit.c to ptrace.c
- Update the comment in ptrace_detach() to explain the rechecking of
the child->ptrace.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Metzger, Markus T" <markus.t.metzger@intel.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When ptrace_detach() takes tasklist, the tracee can be SIGKILL'ed. If it
has already passed exit_notify() we can leak a zombie, because a) ptracing
disables the auto-reaping logic, and b) ->real_parent was not notified
about the child's death.
ptrace_detach() should follow the ptrace_exit's logic, change the code
accordingly.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Tested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: introduce new ptrace facility
Add arch_ptrace_untrace() function that is called when the tracer
detaches (either voluntarily or when the tracing task dies);
ptrace_disable() is only called on a voluntary detach.
Add ptrace_fork() and arch_ptrace_fork(). They are called when a
traced task is forked.
Clear DS and BTS related fields on fork.
Release DS resources and reclaim memory in ptrace_untrace(). This
releases resources already when the tracing task dies. We used to do
that when the traced task dies.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ptrace_untrace() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the change in commit 09a05394fe, I
overlooked two nits in the logic and this broke using CLONE_PTRACE
when PTRACE_O_TRACE* are not being used.
A parent that is itself traced at all but not using PTRACE_O_TRACE*,
using CLONE_PTRACE would have its new child fail to be traced.
A parent that is not itself traced at all that uses CLONE_PTRACE
(which should be a no-op in this case) would confuse the bookkeeping
and lead to a crash at exit time.
This restores the missing checks and fixes both failure modes.
Reported-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Roland McGrath <roland@redhat.com>
This adds the new function task_current_syscall() on machines where the
asm/syscall.h interface is supported (CONFIG_HAVE_ARCH_TRACEHOOK). It's
exported for modules to use in the future. This function safely samples
the state of a blocked thread to collect what system call it is blocked
in, and the six system call argument registers.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the ptrace-related logic from release_task into tracehook.h and
ptrace.h inlines. It provides clean hooks both before and after locking
tasklist_lock, for future tracing logic to do more cleanup without the
lock.
This also changes release_task() itself in the rare "zap_leader" case to
set the leader to EXIT_DEAD before iterating. This maintains the
invariant that release_task() only ever handles a task in EXIT_DEAD. This
is a common-sense invariant that is already always true except in this one
arcane case of zombie leader whose parent ignores SIGCHLD.
This change is harmless and only costs one store in this one rare case.
It keeps the expected state more consisently sane, which is nicer when
debugging weirdness in release_task(). It also lets some future code in
the tracehook entry points rely on this invariant for bookkeeping.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves all the ptrace initialization and tracing logic for task
creation into tracehook.h and ptrace.h inlines. It reorganizes the code
slightly, but should not change any behavior.
There are four tracehook entry points, at each important stage of task
creation. This keeps the interface from the core fork.c code fairly
clean, while supporting the complex setup required for ptrace or something
like it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series introduces the "tracehook" interface layer of inlines in
<linux/tracehook.h>. There are more details in the log entry for patch
01/23 and in the header file comments inside that patch. Most of these
changes move code around with little or no change, and they should not
break anything or change any behavior.
This sets a new standard for uniform arch support to enable clean
arch-independent implementations of new debugging and tracing stuff,
denoted by CONFIG_HAVE_ARCH_TRACEHOOK. Patch 20/23 adds that symbol to
arch/Kconfig, with comments listing everything an arch has to do before
setting "select HAVE_ARCH_TRACEHOOK". These are elaborted a bit at:
http://sourceware.org/systemtap/wiki/utrace/arch/HowTo
The new inlines that arch code must define or call have detailed kerneldoc
comments in the generic header files that say what is required.
No arch is obligated to do any work, and no arch's build should be broken
by these changes. There are several steps that each arch should take so
it can set HAVE_ARCH_TRACEHOOK. Most of these are simple. Providing this
support will let new things people add for doing debugging and tracing of
user-level threads "just work" for your arch in the future. For an arch
that does not provide HAVE_ARCH_TRACEHOOK, some new options for such
features will not be available for config.
I have done some arch work and will submit this to the arch maintainers
after the generic tracehook series settles in. For now, that work is
available in my GIT repositories, and in patch and mbox-of-patches form at
http://people.redhat.com/roland/utrace/2.6-current/
This paves the way for my "utrace" work, to be submitted later. But it is
not innately tied to that. I hope that the tracehook series can go in
soon regardless of what eventually does or doesn't go on top of it. For
anyone implementing any kind of new tracing/debugging plan, or just
understanding all the context of the existing ptrace implementation,
having tracehook.h makes things much easier to find and understand.
This patch:
This adds the new kernel-internal header file <linux/tracehook.h>. This
is not yet used at all. The comments in the header introduce what the
following series of patches is about.
The aim is to formalize and consolidate all the places that the core
kernel code and the arch code now ties into the ptrace implementation.
These patches mostly don't cause any functional change. They just move
the details of ptrace logic out of core code into tracehook.h inlines,
where they are mostly compiled away to the same as before. All that
changes is that everything is thoroughly documented and any future
reworking of ptrace, or addition of something new, would not have to touch
core code all over, just change the tracehook.h inlines.
The new linux/ptrace.h inlines are used by the following patches in the
new tracehook_*() inlines. Using these helpers for the ptrace event stops
makes it simple to change or disable the old ptrace implementation of
these stops conditionally later.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable security modules to distinguish reading of process state via
proc from full ptrace access by renaming ptrace_may_attach to
ptrace_may_access and adding a mode argument indicating whether only
read access or full attach access is requested. This allows security
modules to permit access to reading process state without granting
full ptrace access. The base DAC/capability checking remains unchanged.
Read access to /proc/pid/mem continues to apply a full ptrace attach
check since check_mem_permission() already requires the current task
to already be ptracing the target. The other ptrace checks within
proc for elements like environ, maps, and fds are changed to pass the
read mode instead of attach.
In the SELinux case, we model such reading of process state as a
reading of a proc file labeled with the target process' label. This
enables SELinux policy to permit such reading of process state without
permitting control or manipulation of the target process, as there are
a number of cases where programs probe for such information via proc
but do not need to be able to control the target (e.g. procps,
lsof, PolicyKit, ConsoleKit). At present we have to choose between
allowing full ptrace in policy (more permissive than required/desired)
or breaking functionality (or in some cases just silencing the denials
via dontaudit rules but this can hide genuine attacks).
This version of the patch incorporates comments from Casey Schaufler
(change/replace existing ptrace_may_attach interface, pass access
mode), and Chris Wright (provide greater consistency in the checking).
Note that like their predecessors __ptrace_may_attach and
ptrace_may_attach, the __ptrace_may_access and ptrace_may_access
interfaces use different return value conventions from each other (0
or -errno vs. 1 or 0). I retained this difference to avoid any
changes to the caller logic but made the difference clearer by
changing the latter interface to return a bool rather than an int and
by adding a comment about it to ptrace.h for any future callers.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
Add another trivial helper for the sake of grep. It also auto-documents the
fact that ->parent != real_parent implies ->ptrace.
No functional changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the patch
"Fix ptrace_attach()/ptrace_traceme()/de_thread() race"
commit f5b40e363a
we set PT_ATTACHED and change child->parent "atomically" wrt task_list lock.
This means we can remove the checks like "PT_ATTACHED && ->parent != ptracer"
which were needed to catch the "ptrace attach is in progress" case. We can
also remove the flag itself since nobody else uses it.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support to allow asm/ptrace.h to define two new macros,
arch_ptrace_stop_needed and arch_ptrace_stop. These control special
machine-specific actions to be done before a ptrace stop. The new code
compiles away to nothing when the new macros are not defined. This is the
case on all machines to begin with.
On ia64, these macros will be defined to solve the long-standing issue of
ptrace vs register backing store.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes ptrace_request handle PTRACE_SINGLEBLOCK along with
PTRACE_CONT et al. The new generic code makes use of the
arch_has_block_step macro and generic entry points on machines
that define them.
[ mingo@elte.hu: bugfix ]
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This defines the new macro arch_has_block_step() in linux/ptrace.h, a
default for when asm/ptrace.h does not define it. This is the analog
of arch_has_single_step() for step-until-branch on machines that have
it. It declares the new user_enable_block_step function, which goes
with the existing user_enable_single_step and user_disable_single_step.
This is not used yet, but paves the way to harmonize on this interface
for the arch-specific calls on all machines.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This defines the new macro arch_has_single_step() in linux/ptrace.h, a
default for when asm/ptrace.h does not define it. It declares the new
user_enable_single_step and user_disable_single_step functions.
This is not used yet, but paves the way to harmonize on this interface
for the arch-specific calls on all machines.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Will Drewry
Linus Torvalds
Denys Vlasenko
Oleg Nesterov
Paul Gortmaker
Eric Paris
Tejun Heo
Frederic Weisbecker
Namhyung Kim
Peter Zijlstra
Christoph Hellwig
Suresh Siddha
Markus Metzger
Adrian Bunk
Roland McGrath
Stephen Smalley
Oleg Nesterov