This is a respin of my earlier patch that migrates the ATA support code
into a separate file. For now, the controversial linking bits have
been removed per James Bottomley's request for a patch that contains
only the migration diffs, which means that libsas continues to require
libata. I intend to address that problem in a separate patch.
This patch is against the aic94xx-sas-2.6 git tree, and it has been
sanity tested on my x206m with Seagate SATA and SAS disks without
uncovering any new problems.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We actually had two problems: the one with the tag (which is fixed by
zeroing the tag before sending the taskfile to the sequencer) but the
other with the fact that we sent our first NCQ command to the device
before the sequencer had been informed of the NCQ tagging
capabilities. I fixed the latter by moving the rphy_add() to the
correct point in the code after the NCQ capabilities are set up.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This replaces a few BUG_ON() statements with the correct failure error
handling. There are still many more to do.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It turns out this is fairly easy to plumb in by recognising the three
command types and copying the CDB. The protocol response path needs to
be amended to cope with SAS_PROTO_RESPONSE.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds SATAII NCQ support to libsas. Both the use_ncq and the
dma_xfer flags in ata_task must be set for NCQ to work correctly on the
Adaptec SAS controller. The rest of the patch adds ATA_FLAG_NCQ to
sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't
crash. Please note that this patch is against the aic94xx-sas git tree,
not scsi-misc. Thanks also to James Bottomley for providing an earlier
version of this patch from which to work.
I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged
into the Adaptec SAS controller. The drive came up with a queue depth
of 31, and I successfully ran an I/O flood test to coerce libata into
sending multiple commands simultaneously. A kernel probe recorded the
maximum tag number that had been seen before and after the flood test;
before the test it was 2 and after it was 30, as I expected.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The prototype of this has changed for the link speed setting patch.
Need to update the SATA use of this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for SATA over SAS expanders to the previous two
SATA support in libsas patches.
There were a couple of nasty non trivial things to sort out before this
one could be made to work.
Firstly, I'd like to thank Doug Gilbert for diagnosing a problem with
the LSI expanders where the REPORT_SATA_PHY command was returning the
D2H FIS in the wrong order (Although, here, I think I have to blame the
SAS standards which specifies the FIS "shall be returned in little
endian format" and later on "which means resp[24] shall be FIS type"
The latter, of course, implying big endian format). Just to make sure,
I put a check for the D2H FIS type being in the wrong position and
reverse the FIS data if it is.
The second is a problem outlined in Annex G of the SAS standard (again,
a technical point with D2H FIS ... necessitating a phy reset on certain
conditions).
With the patch, I can now see my SATA-1 disk in a cascaded expander
configuration.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hook the scsi_host_template functions in libsas to delegate
functionality to libata when appropriate.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Misc code changes and merge fixes and update for libata->drivers/ata
move
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After discussion with andmike and dougg, it seems that the purpose of
eh_device_reset_handler is to issue LU resets, and that
eh_bus_reset_handler would be a more appropriate place for a phy reset.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsas: Don't BUG when connecting two expanders via wide port
When a device is connected to an expander, the discovery process goes through
sas_ex_discover_dev to figure out what's attached to the phy. If it is the
case that the phy being discovered happens to be the second phy of a wide link
to an expander, that discover_dev function will incorrectly call
sas_ex_discover_expander, which creates another sas_port and tries to attach the
other sas_phys to the new port, thus triggering a BUG. The correct thing to do is
to check the other ex_phys of the expander to see if there's a sas_port for this
sas_phy, and attach the sas_phy to the existing sas_port.
This is easily triggered if one enables the phys of a wide port between
expanders one by one.
This second version of the patch fixes a small regression in the case where
all the phys show up at once and we accidentally try to attach to a port
that hasn't been created yet.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set allow_restart=1 for all SAS disks so that they are spun up when needed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch moves the code that handles SAS failures out of the main EH
function and into a separate function. It also detects commands that have
no sas_task (i.e. they completed, but with error data) and sends them into
scsi_error for processing. This allows us to handle SCSI errors (and
enables auto-spinup as a side effect) instead of dropping them on the
floor and falling into an infinite loop. It also requires the
implementation of a device reset function, which the SAS failure code has
been modified to employ for REQ_DEVICE_RESET.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_rphy_delete does two things: it removes the sas_rphy from the transport
layer and frees the sas_rphy. This can be broken down into two functions,
sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to
sas_discover_root_expander because it calls functions that require
sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander).
In that case, sas_discover_root_expander needs to be able to undo the effects
of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of
sas_discover_root_expander.
This patch also removes some unnecessary code from sas_discover_end_dev
to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS
devices, thus eliminating a sas_rphy_remove call (and fixing a race condition
where a SCSI target scan can come in between the gone and found call).
It also moves the sas_rphy_free calls into sas_discover_domain and
sas_ex_discover_end_dev to complement the sas_rphy_allocation via
sas_get_port_device.
This patch does not change the semantics of sas_rphy_delete.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, sas_form_port checks the given asd_sas_phy's sas_phy to see if
there's already a port attached. If so, the SAS addresses of the port and
the phy are compared to determine if we need to detach from the port
because the addresses don't match or if we can stop; the SAS address stored
in the sas_port reflects whatever device _was_ attached to the port/phy, and
the SAS address stored in the sas_port reflects whatever device we just
discovered. As written, the code detaches from the port if the addresses
_do_ match, and prints an error if they do _not_ match. I believe this to
be incorrect, as it seems more logical to keep the port if the addresses
match (i.e. the phy was reset but the device didn't change), and detach it
they do not (i.e. the device changed).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The EH should fall into I_T recovery (and potentially stronger
remedies) if ABORT TASK fails.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Track sas_ha_struct state so that we ignore events that come in while
we're shutting things down.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the phy port locks to use irq spinlocks.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_task_abort() should simply abort the upper-level SCSI command and wait
until the error handler to send the actual ABORT TASK command. By
deferring things to the EH we simplify the concurrency coordination and
eliminate some race conditions. Note that sas_task_abort has a few hooks
to handle libsas internal commands properly too.
Also rename do_sas_task_abort to __sas_task_abort just in case we really
want to abort the task *right now* and we don't have a scsi_cmnd attached
to the command. This is a hook for libata internal commands to abort.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a SAS LLDD needs to request a device port reset, it needs to have all
commands aborted before it can reset the port. Since commands are put on
the EH's list in the order that they were queued, the LLDD can set a "need
reset" flag in the last task to be aborted so that the EH can reset the
port after all commands are aborted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This flag is no longer necessary because we push tasks to be aborted into
the EH as soon as we possibly can, and let the SCSI EH code take care of
the coordination for which this flag was used.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we use task collector mode, we can end up destroying the task collector
thread before we release the ports, which is bad if a port release causes
a disk I/O (such as cache flushing).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Every so often, a scsi_cmnd will time out, and the libsas timeout handler
will discover that the scsi_cmnd does not have a sas_task attached to it.
This can happen in two cases: (1) the scsi_cmnd actually made it through
libsas to the HBA and is now going through scsi_done, or (2) the
scsi_cmnd has been held up (host lock, slab alloc, etc) and libsas has
not yet attached a sas_task. In both cases, it is safe to ask SCSI for
more time to process the command via EH_RESET_TIMER; we cannot blindly
return EH_HANDLED because if (2) happens, we could end up calling
scsi_done while another CPU is heading towards sas_queuecommand, which
causes slab corruption when sas_task_done updates the freed scsi_cmnd.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch lets a user arbitrarily enable or disable a phy via sysfs.
Potential applications include shutting down a phy to replace one
lane of wide port, and (more importantly) providing a method for the
libata SATL to control the phy.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On a system with many SAS targets, it appears possible that a scsi_cmnd
can time out without ever making it to the SAS LLDD or at the same time
that a completion is occurring. In both of these cases, telling the
LLDD to abort the sas_task makes no sense because the LLDD won't know
about the sas_task; what we really want to do is to increase the timer.
Note that this involves creating another sas_task bit to indicate
whether or not the task has been sent to the LLDD; I could have
implemented this by slightly redefining SAS_TASK_STATE_PENDING, but
this way seems cleaner.
This second version amends the aic94xx portion to set the
TASK_AT_INITIATOR flag for all sas_tasks that were passed to
lldd_execute_task.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
This patch fixes up sas_expander.c separately because jejb has some
cleanup patches of his own that are a prerequisite.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/pcmcia/ds.c
Fix up merge failures with Linus's head and fix new compile failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
With async scanning, we're now tripping the BUG_ON in
sas_ex_discover_end_dev(), so make the error handling here correct.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch implements a REQ_DEVICE_RESET handler for the aic94xx
driver. Like the earlier REQ_TASK_ABORT patch, this patch defers the
device reset to the Scsi_Host's workqueue, which has the added benefit
of ensuring that the device reset does not happen at the same time
that the abort tmfs are being processed. After the phy reset, the
busted drive should go away and be re-detected later, which is indeed
what I've seen on both a x260 and a x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds an external function, sas_abort_task, to enable LLDDs
to abort sas_tasks. It also adds a work_struct so that the actual
work of aborting a task can be shifted from tasklet context (in the
LLDD) onto the scsi_host's workqueue.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds an EH done queue to sas_ha, converts the error handling
strategy function and the sas_scsi_task_done functions in libsas to use
the scsi_eh_* commands for error'd commands, and adds checks for the
INITIATOR_ABORTED flag so that we do the right thing if a sas_task has
been aborted by the initiator.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updating DDB0 inside aic94xx driver itself caused SMP command timeout. I
hit this SMP timeout problem twice but I am not able to reproduce it since
then. Here is a fix that retries an SMP command.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ->flags in struct request was split into two variables, in a recent
changeset. The merge of this change forgot to update SCSI's libsas,
probably because libsas was a very recent merge.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements the ability to set the minimum and maximum
linkrates for both libsas (for expanders) and aic94xx (for the host
phys). It also tidies up the setting of the hardware min and max to
make sure they're updated when the expander emits a change broadcast.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
At the moment we have two separate linkspeed enumerations covering
roughly the same values. This patch consolidates on a single one enum
sas_linkspeed in scsi_transport_sas.h and uses it everywhere in the
aic94xx driver. Eventually I'll get around to removing the duplicated
fields in asd_sas_phy and sas_phy ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong
James Bottomley
James Bottomley
James Bottomley
Rafael J. Wysocki
Linus Torvalds
Zhang Rui
Tejun Heo
FUJITA Tomonori
Christoph Hellwig
Jean Delvare
Christoph Lameter
David Howells
malahal@us.ibm.com
Jeff Garzik
Al Viro