then a bunch of driver updates and a handful of new drivers. In terms of
diffstat the Qualcomm and Amlogic drivers are high up there because of all the
clk data introcued by new drivers. The Nvidia Tegra driver had a lot of work
done this cycle too to support suspend/resume and memory controllers. And the
OMAP clk driver got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data, mark things
static, correct incorrect data in drivers, etc. All the little things that
improve drivers and maintain code health. I will point out that there's a patch
in here for the GPIO clk driver, that almost nobody uses, which changes
behavior and causes clk_set_rate() to try to change the GPIO gate clk's parent.
Other than that things are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8 SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system suspend/resume cycle
on exynos542x SoCs
-----BEGIN PGP SIGNATURE-----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=qJNg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
The buffer allocated in ti_adpll_clk_get_name doesn't account for the
terminating null. This patch switches to devm_kasprintf to avoid
overflowing.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20191019140634.15596-1-steve@sk2.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
merged this merge window. The Amlogic driver was missing some flags
causing rates to be rounded improperly or clk_set_rate() to fail. The
Samsung driver wasn't freeing everything on error paths and improperly
saving/restoring PLL state across suspend/resume. The at91 driver was
calling msleep() too early when scheduling hadn't started, so we put in
place a quick solution until we can handle this sort of problem in the
core framework. There were also problems with the Allwinner driver and
operator precedence being incorrect causing subtle bugs. Finally, the TI
driver was duplicating aliases and not delaying long enough leading to
some unexpected timeouts.
-----BEGIN PGP SIGNATURE-----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=0xes
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Fixes for various clk driver issues that happened because of code we
merged this merge window.
The Amlogic driver was missing some flags causing rates to be rounded
improperly or clk_set_rate() to fail. The Samsung driver wasn't
freeing everything on error paths and improperly saving/restoring PLL
state across suspend/resume. The at91 driver was calling msleep() too
early when scheduling hadn't started, so we put in place a quick
solution until we can handle this sort of problem in the core
framework.
There were also problems with the Allwinner driver and operator
precedence being incorrect causing subtle bugs. Finally, the TI driver
was duplicating aliases and not delaying long enough leading to some
unexpected timeouts"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: clkctrl: Fix failed to enable error with double udelay timeout
clk: ti: dra7-atl-clock: Remove ti_clk_add_alias call
clk: sunxi-ng: a80: fix the zero'ing of bits 16 and 18
clk: sunxi: Fix operator precedence in sunxi_divs_clk_setup
clk: ast2600: Fix enabling of clocks
clk: at91: avoid sleeping early
clk: imx8m: Use SYS_PLL1_800M as intermediate parent of CLK_ARM
clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume
clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU
clk: samsung: exynos5433: Fix error paths
clk: at91: sam9x60: fix programmable clock
clk: meson: g12a: set CLK_MUX_ROUND_CLOSEST on the cpu clock muxes
clk: meson: g12a: fix cpu clock rate setting
clk: meson: gxbb: let sar_adc_clk_div set the parent clock rate
Commit 3d8598fb9c ("clk: ti: clkctrl: use fallback udelay approach if
timekeeping is suspended") added handling for cases when timekeeping is
suspended. But looks like we can still get occasional "failed to enable"
errors on the PM runtime resume path with udelay() returning faster than
expected.
With ti-sysc interconnect target module driver this leads into device
failure with PM runtime failing with "failed to enable" clkctrl error.
Let's fix the issue with a delay of two times the desired delay as in
often done for udelay() to account for the inaccuracy.
Fixes: 3d8598fb9c ("clk: ti: clkctrl: use fallback udelay approach if timekeeping is suspended")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20190930154001.46581-1-tony@atomide.com
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The existing width field used to check divider validity does not provide
enough protection against bad values. For example, if max divider value
is 4, the smallest all-1 bitmask that can hold this value is 7, which
allows values higher than 4 to be used. This typically causes
unpredictable results with hardware. So far this issue hasn't been
noticed as most of the dividers actually have maximum values which fit
the whole bitfield, but there are certain clocks for which this is a
problem, like dpll4_m4 divider on omap3 devices.
Thus, convert the whole validity logic to use min,max and mask values
for determining if a specific divider is valid or not. This prevents
the odd cases where bad value would otherwise be written to a divider
config register.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Cleanup the ti_clk_parse_divider_data to pass the divider data struct
directly instead of individual values of it. This makes it easier
to modify the implementation later on.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Cleanup couple of TI divider clock internal APIs. These currently pass
huge amount of parameters, which makes it difficult to track what is
going on. Abstract most of these under struct clk_omap_div which gets
passed over the APIs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Due to the way ti sysc and hardreset line control is now implemented,
it is not possible to poll the clock status for gfx clock independent
of hardreset line control. Thus, add a flag to prevent handling this
status bit from clock driver. Correct sequencing of events is guaranteed
by ti-sysc bus driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Due to the way ti sysc and hardreset line control is now implemented,
it is not possible to poll the clock status for gfx clock independent
of hardreset line control. Thus, add a flag to prevent handling this
status bit from clock driver. Correct sequencing of events is guaranteed
by ti-sysc bus driver.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The PRUSS module on AM33xx SoCs has a hardreset line and is controlled
by a PRCM reset line. Any clkctrl enable/disable operations cannot be
checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for the PRUSS clocks. These details should be handled
by the driver integration code itself.
Add the CLKF_NO_IDLEST flag to the PRUSS clkctrl clock so that these
module status checks are skipped.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The PRUSS modules on AM43xx SoCs have a hardreset line and are controlled
by a PRCM reset line. Any clkctrl enable/disable operations cannot be
checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for the PRUSS clocks. These details should be handled
by the driver integration code itself.
Add the CLKF_NO_IDLEST flag to the PRUSS clkctrl clock so that these
module status checks are skipped.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The IPU and DSP remote processor cores and their corresponding MMUs on
OMAP5 SoCs have hardreset lines associated with them and are controlled
by a PRCM reset line each. Any clkctrl enable/disable operations cannot
be checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for these clocks. These details should be handled by
the driver integration code itself.
Add the CLKF_NO_IDLEST flag to both the IPU and DSP clkctrl clocks so
that these module status checks are skipped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The IPU and DSP remote processor cores and their corresponding MMUs on
OMAP4 SoCs have hardreset lines associated with them and are controlled
by a PRCM reset line each. Any clkctrl enable/disable operations cannot
be checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for these clocks. These details should be handled by
the driver integration code itself.
Add the CLKF_NO_IDLEST flag to both the IPU and DSP clkctrl clocks so
that these module status checks are skipped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The IPU and DSP remote processor cores and their corresponding MMUs on
DRA7 SoCs have hardreset lines associated with them and are controlled
by a PRCM reset line each. Any clkctrl enable/disable operations cannot
be checked for module enabled/disabled status independent of the reset
operation, and this causes some unwanted timeouts in the kernel and
unbalanced states for these clocks. These details should be handled by
the driver integration code itself.
Add the CLKF_NO_IDLEST flag to both the IPU and DSP clkctrl clocks so
that these module status checks are skipped.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Standby status is provided for certain clkctrl clocks to see if the
given module has entered standby or not. This is mostly needed by
remoteproc code to see if the remoteproc has entered standby and the clock
can be turned off safely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Apply the proper register function for clkctrl clocks, so they get
registered under the clk_hw_omap list also. This allows checking their
type runtime.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
-----BEGIN PGP SIGNATURE-----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=SkMF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
* tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a typo for dra7 mcasp clkctrl bit, it should be 22 like the other
macasp instances, and not 24. And in dra7xx_clks[] we have the bits wrong
way around.
Fixes: dffa9051d5 ("clk: ti: dra7: add new clkctrl data")
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is some material that we picked up into our tree late or
that had complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the most
interesting new additions:
The new Aspeed AST2600 baseboard management controller is added, this
is a Cortex-A7 based follow-up to the ARM11 based AST2500 and had some
dependencies on other device drivers.
After many years, support for the MMP2 based OLPC XO-1.75 finally makes
it into the kernel.
The Armada 3720 based Turris Mox open source router platform is a late
addition and it follows some preparatory work across multiple branches.
The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of the
now-unused platform data.
The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Qtkp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lkml.kernel.org/r/20190703162700.32091-1-huangfq.daxian@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Looks like we have sgx clock missing currently so let's add it.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190815221249.53235-1-sboyd@kernel.org
In function dm814x_adpll_early_init, variable np takes the value
returned by of_find_node_by_name, which gets a node but does not put it.
If np is not put before return, it may cause a memory leak. Hence put np
before return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lkml.kernel.org/r/20190804163328.6693-1-nishkadg.linux@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
- Do a DT/firmware lookup in clk_core_get() even when the DT index is a
nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio
-----BEGIN PGP SIGNATURE-----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=3QYB
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes and one core framework fix
- Do a DT/firmware lookup in clk_core_get() even when the DT index is
a nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: socfpga: stratix10: fix divider entry for the emac clocks
clk: Do a DT parent lookup even when index < 0
clk: tegra210: Fix default rates for HDA clocks
clk: ti: clkctrl: Fix returning uninitialized data
clk: meson: meson8b: fix a typo in the VPU parent names array variable
clk: meson: fix MPLL 50M binding id typo
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are not used any more since
commit 7558562a70 ("clk: ti: Drop legacy clk-3xxx-legacy code")
Reported-by: Hulk Robot <hulkci@huawei.com>
Suggested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If we do a clk_get() for a clock that does not exists, we have
_ti_omap4_clkctrl_xlate() return uninitialized data if no match
is found. This can be seen in some cases with SLAB_DEBUG enabled:
Unable to handle kernel paging request at virtual address 5a5a5a5a
...
clk_hw_create_clk.part.33
sysc_notifier_call
notifier_call_chain
blocking_notifier_call_chain
device_add
Let's fix this by setting a found flag only when we find a match.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes: 88a172526c ("clk: ti: add support for clkctrl clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Don't expose the SiFive clk driver on non-RISCV architectures
- Fix some bits describing clks in the imx8mm driver
- Always call clk domain code in the TI driver so non-legacy platforms
work
-----BEGIN PGP SIGNATURE-----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=gbSJ
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
- Don't expose the SiFive clk driver on non-RISCV architectures
- Fix some bits describing clks in the imx8mm driver
- Always call clk domain code in the TI driver so non-legacy platforms
work
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: clkctrl: Fix clkdm_clk handling
clk: imx: imx8mm: fix int pll clk gate
clk: sifive: restrict Kconfig scope for the FU540 PRCI driver
We need to always call clkdm_clk_enable() and clkdm_clk_disable() even
the clkctrl clock(s) enabled for the domain do not have any gate register
bits. Otherwise clockdomains may never get enabled except when devices get
probed with the legacy "ti,hwmods" devicetree property.
Fixes: 88a172526c ("clk: ti: add support for clkctrl clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RNG and TIMER12 are reserved for secure side usage only on HS devices,
so disable their clkctrl clocks on HS SoCs also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Certain clkctrl clocks (like the USB_OTG_SS4) do not exist on some
variants of the dra7x SoC. Append a flag for these clocks and skip
the registration in cases where the clocks do not exist.
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is one instance outside the TI clock driver that needs the info
whether a clock is an OMAP HW clock or not. Thus, move the function
declaration into the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional() API
to get clks that may not always be populated and a way to devm manage clkdev
lookups registered by provider drivers. We also do some refactoring to simplify
the interface between clkdev and the common clk framework so we can reuse the DT
parsing and clk_get() path in provider drivers in the future. This work will
continue in the next few cycles while we convert how providers specify clk
parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk driver
that got support for the G12A SoC. It dominates with almost half the overall
diff, while the second largest part of the diff is in the i.MX clk driver
that gained support for imx8mm SoCs. After that, we have the Actions Semiconductor
and Qualcomm drivers rounding out the big part of the dirstat because they both
got new hardware support for SoCs. The rest is just various updates and non-critical
fixes for existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support
-----BEGIN PGP SIGNATURE-----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=D4Bv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a72d785021 ("clk: ti: Prepare for remove of OF node name")
changed the code to use kasprintf() for provider->clkdm_name but also
changed the offset used later on by three. We don't need to change the
offset as we already have the extra three characters in the format for
kasprintf with "%pOFnxxx".
This caused the clocks with TI_CLK_CLKCTRL_COMPAT to have NULL
clk->clkdm_name for omap4 and 5. And null clkdm_name can cause module
reset, enable, and idle to fail.
The issue can also be seen also when enabling DEBUG for clkctrl.c
and then we start seeing "clock: could not associate" messages for
omap4 and 5 as the generated name is something like "l4_wkclkdm" instead
of "l4_wkup_clkdm" that's needed.
Let's fix the issue with a partial revert of commit a72d785021 ("clk:
ti: Prepare for remove of OF node name").
ALso note that in general code should not depend on the dts node names.
And the node names should be generic types like clock-domain in this case.
This could be fixed later by using separate compatible properties for the
clockdomains, or by adding soc_device_match() table with reg offsets
to the driver. But let's fix the regression first.
Fixes: a72d785021 ("clk: ti: Prepare for remove of OF node name")
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Split LCDC into two clks on the Marvell MMP2 SoC
* clk-imx:
clk: imx8mq: add GPIO clocks to clock tree
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: imx: imx8mm: Mark init function __init
clk: imx8mq: Add the missing ARM clock
dt-bindings: imx8mq-clock: Add the missing ARM clock
clk: imx: imx8mq: Fix the rate propagation for arm pll
clk: imx8mq: Add support for the CLKO1 clock
clk: imx8mq: Fix the CLKO2 source select list
clk: imx8mq: Add missing M4 clocks
clk: imx: Add clock driver support for imx8mm
dt-bindings: imx: Add clock binding doc for imx8mm
clk: imx: Add PLLs driver for imx8mm soc
clk: imx5: add imx5_SCC2_IPG_GATE
clk: imx: scu: add set parent support
clk: imx: scu: add fallback compatible string support
clk: imx8mq: Make parent names arrays const pointers
clk: imx: Make parents const pointer in mux wrappers
clk: imx: Make parent_names const pointer in composite-8m
* clk-samsung:
clk: samsung: s3c2443: Mark expected switch fall-through
clk: samsung: exynos5: Fix kfree() of const memory on setting driver_override
clk: samsung: exynos5: Fix possible NULL pointer exception on platform_device_alloc() failure
clk: samsung: exynos5433: Add selected IMEM clocks
clk: samsung: dt-bindings: Document Exynos5433 IMEM CMU
clk: samsung: exynos5433: Fix name typo in sssx
clk: samsung: exynos5433: Fix definition of CLK_ACLK_IMEM_{200, 266} clocks
clk: samsung: dt-bindings: Add Exynos5433 IMEM CMU clock IDs
* clk-ti:
clk: clk-twl6040: Fix imprecise external abort for pdmclk
ARM: OMAP2+: hwmod: disable ick autoidling when a hwmod requires that
clk: ti: check clock type before doing autoidle ops
clk: ti: add a usecount for autoidle
clk: ti: generalize the init sequence of clk_hw_omap clocks
clk: ti: remove usage of CLK_IS_BASIC
clk: ti: add new API for checking if a provided clock is an OMAP clock
clk: ti: move clk_hw_omap list handling under generic part of the driver
* clk-uniphier-gear:
clk: uniphier: Fix update register for CPU-gear
* clk-mmp2-lcdc:
clk: mmp2: separate LCDC peripheral clk form the display clock
dt-bindings: marvell,mmp2: Add clock id for the LCDC clock
Code might use autoidle api with clocks not being omap2 clocks,
so check if clock type is really omap2.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Multiple users might deny autoidle on a clock. So we should have some
counting here, also according to the comment in _setup_iclk_autoidle().
Also setting autoidle regs is not atomic, so there is another reason
for locking.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add a generic API for initializing clocks of clk_hw_omap type clocks,
and convert the whole TI clock driver suite to use this for registering
the clocks. Also, get rid of the now redundant API for adding the clocks
to the OMAP HW clocks list; instead this is used directly from the
register API.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Remove the usage of CLK_IS_BASIC flag completely from TI clock driver.
In most cases, the use is completely redundant, but in some cases
we need to use the new API to check if the clock is an OMAP clock or not.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Linus Torvalds
Stephen Kitt
Tony Lindgren
Peter Ujfalusi
Tero Kristo
Suman Anna
Olof Johansson
Stephen Boyd
Fuqian Huang
Nishka Dasgupta
Thomas Gleixner
YueHaibing
Mike Rapoport
Andreas Kemnade