Граф коммитов

29 Коммитов

Автор SHA1 Сообщение Дата
Markus Stockhausen a582564b24 md/raid6 algorithms: xor_syndrome() for SSE2
The second and (last) optimized XOR syndrome calculation. This version
supports right and left side optimization. All CPUs with architecture
older than Haswell will benefit from it.

It should be noted that SSE2 movntdq kills performance for memory areas
that are read and written simultaneously in chunks smaller than cache
line size. So use movdqa instead for P/Q writes in sse21 and sse22 XOR
functions.

Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2015-04-22 08:00:42 +10:00
Markus Stockhausen 9a5ce91d05 md/raid6 algorithms: xor_syndrome() for generic int
Start the algorithms with the very basic one. It is left and right
optimized. That means we can avoid all calculations for unneeded pages
above the right stop offset. For pages below the left start offset we
still need the syndrome multiplication but without reading data pages.

Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2015-04-22 08:00:42 +10:00
Markus Stockhausen 7e92e1d762 md/raid6 algorithms: improve test program
It is always helpful to have a test tool in place if we implement
new data critical algorithms. So add some test routines to the raid6
checker that can prove if the new xor_syndrome() works as expected.

Run through all permutations of start/stop pages per algorithm and
simulate a xor_syndrome() assisted rmw run. After each rmw check if
the recovery algorithm still confirms that the stripe is fine.

Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2015-04-22 08:00:42 +10:00
Markus Stockhausen fe5cbc6e06 md/raid6 algorithms: delta syndrome functions
v3: s-o-b comment, explanation of performance and descision for
the start/stop implementation

Implementing rmw functionality for RAID6 requires optimized syndrome
calculation. Up to now we can only generate a complete syndrome. The
target P/Q pages are always overwritten. With this patch we provide
a framework for inplace P/Q modification. In the first place simply
fill those functions with NULL values.

xor_syndrome() has two additional parameters: start & stop. These
will indicate the first and last page that are changing during a
rmw run. That makes it possible to avoid several unneccessary loops
and speed up calculation. The caller needs to implement the following
logic to make the functions work.

1) xor_syndrome(disks, start, stop, ...): "Remove" all data of source
blocks inside P/Q between (and including) start and end.

2) modify any block with start <= block <= stop

3) xor_syndrome(disks, start, stop, ...): "Reinsert" all data of
source blocks into P/Q between (and including) start and end.

Pages between start and stop that won't be changed should be filled
with a pointer to the kernel zero page. The reasons for not taking NULL
pages are:

1) Algorithms cross the whole source data line by line. Thus avoid
additional branches.

2) Having a NULL page avoids calculating the XOR P parity but still
need calulation steps for the Q parity. Depending on the algorithm
unrolling that might be only a difference of 2 instructions per loop.

The benchmark numbers of the gen_syndrome() functions are displayed in
the kernel log. Do the same for the xor_syndrome() functions. This
will help to analyze performance problems and give an rough estimate
how well the algorithm works. The choice of the fastest algorithm will
still depend on the gen_syndrome() performance.

With the start/stop page implementation the speed can vary a lot in real
life. E.g. a change of page 0 & page 15 on a stripe will be harder to
compute than the case where page 0 & page 1 are XOR candidates. To be not
to enthusiatic about the expected speeds we will run a worse case test
that simulates a change on the upper half of the stripe. So we do:

1) calculation of P/Q for the upper pages

2) continuation of Q for the lower (empty) pages

Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2015-04-22 08:00:41 +10:00
Jan Beulich 75aaf4c3e6 x86/raid6: correctly check for assembler capabilities
Just like for AVX2 (which simply needs an #if -> #ifdef conversion),
SSSE3 assembler support should be checked for before using it.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2015-02-04 08:35:51 +11:00
Anton Blanchard b395f75eab lib/raid6: Add log level to printks
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2014-10-14 13:08:29 +11:00
Linus Torvalds 4d7696f1b0 md update for v3.12
Headline item is multithreading for RAID5 so that more
 IO/sec can be supported on fast (SSD) devices.
 Also TILE-Gx SIMD suppor for RAID6 calculations and an
 assortment of bug fixes.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIVAwUAUi6dRTnsnt1WYoG5AQIqMBAAm/XUEqfyBNUiTPHmIU/OyReOlfsp8A2o
 xtcmSzaCtIUz4btPszUrw3PShqnk+lXXX2AB0rp3PzfOgyNYXBRKbzOf3eGr2VEp
 L/Cm0iSWHqQ7V7MoV5ZrqtvuyJV1a7FK3a3VaoKaUk424o4sZ7P67t/YZAnTCP/i
 9wQoPeIOJ8YjZsaAQjzI3q7yRMRE8ytyBnF4NdgeMyr2p17w2e9pnmNfCTo4wnWs
 Nu2wPr2QCPQXr/FoIhdIVEy3kVatqH8qXG8Fw+5n07HJYxGCvQZLDuoOVDYyFeoW
 gnNq2MMgLZm/7Nzqd1bN+QQZuBCd5JL4VJ2G4vLfYrn3ZSdSysrVKQXFKYG3Gkua
 1KP4Pv0hndAl4DtGbUk8CiZp6b+c5qeWvq+sO2NuhUGmumFMK2q4DJhITNexjmrs
 Eg4opnR8JMLDkYD6o52Ziu5KQR/q1PKRLj80eoVuqB2QQM5+NPb4s3k2WN+53lQD
 L9fH2alUxxSK+5R8ykk923QQ/XErMUwXaka+O/gGFAlYvaaW/GKTxFnKn/GIXAkc
 tKW88zB+zA5EZEFec+K43z1UjtGxMWsryvDN55ON2iV+LIZBISm7krroBeR55cyO
 +3tHlPsga0pO+9DdSm7hvZeWRrq5ZJTiZmL/e2FYygrC5tFAY0p+z49fK3e9Th13
 C85G7fg3yDY=
 =zLxh
 -----END PGP SIGNATURE-----

Merge tag 'md/3.12' of git://neil.brown.name/md

Pull md update from Neil Brown:
 "Headline item is multithreading for RAID5 so that more IO/sec can be
  supported on fast (SSD) devices.  Also TILE-Gx SIMD suppor for RAID6
  calculations and an assortment of bug fixes"

* tag 'md/3.12' of git://neil.brown.name/md:
  raid5: only wakeup necessary threads
  md/raid5: flush out all pending requests before proceeding with reshape.
  md/raid5: use seqcount to protect access to shape in make_request.
  raid5: sysfs entry to control worker thread number
  raid5: offload stripe handle to workqueue
  raid5: fix stripe release order
  raid5: make release_stripe lockless
  md: avoid deadlock when dirty buffers during md_stop.
  md: Don't test all of mddev->flags at once.
  md: Fix apparent cut-and-paste error in super_90_validate
  raid6/test: replace echo -e with printf
  RAID: add tilegx SIMD implementation of raid6
  md: fix safe_mode buglet.
  md: don't call md_allow_write in get_bitmap_file.
2013-09-10 13:03:41 -07:00
Max Filippov c28399b594 raid6/test: replace echo -e with printf
-e is a non-standard echo option, echo output is
implementation-dependent when it is used. Replace echo -e with printf as
suggested by POSIX echo manual.

Cc: NeilBrown <neilb@suse.de>
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-27 16:06:06 +10:00
Ken Steele ae77cbc1e7 RAID: add tilegx SIMD implementation of raid6
This change adds TILE-Gx SIMD instructions to the software raid
(md), modeling the Altivec implementation. This is only for Syndrome
generation; there is more that could be done to improve recovery,
as in the recent Intel SSE3 recovery implementation.

The code unrolls 8 times; this turns out to be the best on tilegx
hardware among the set 1, 2, 4, 8 or 16.  The code reads one
cache-line of data from each disk, stores P and Q then goes to the
next cache-line.

The test code in sys/linux/lib/raid6/test reports 2008 MB/s data
read rate for syndrome generation using 18 disks (16 data and 2
parity). It was 1512 MB/s before this SIMD optimizations. This is
running on 1 core with all the data in cache.

This is based on the paper The Mathematics of RAID-6.
(http://kernel.org/pub/linux/kernel/people/hpa/raid6.pdf).

Signed-off-by: Ken Steele <ken@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-27 16:05:50 +10:00
Ard Biesheuvel 7d11965ddb lib/raid6: add ARM-NEON accelerated syndrome calculation
Rebased/reworked a patch contributed by Rob Herring that uses
NEON intrinsics to perform the RAID-6 syndrome calculations.
It uses the existing unroll.awk code to generate several
unrolled versions of which the best performing one is selected
at boot time.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: hpa@linux.intel.com
2013-07-08 22:09:18 +01:00
Yuanhan Liu 4f8c55c5ad lib/raid6: build proper files on corresponding arch
sse and avx2 stuff only exist on x86 arch, and we don't need to build
altivec on x86. And we can do that at lib/raid6/Makefile.

Proposed-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-12-13 19:51:04 +11:00
Yuanhan Liu 2c935842bd lib/raid6: Add AVX2 optimized gen_syndrome functions
Add AVX2 optimized gen_syndrom functions, which is simply based on
sse2.c written by hpa.

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-12-13 19:51:03 +11:00
Jim Kukunas 7056741fd9 lib/raid6: Add AVX2 optimized recovery functions
Optimize RAID6 recovery functions to take advantage of
the 256-bit YMM integer instructions introduced in AVX2.

The patch was tested and benchmarked before submission.
However hardware is not yet released so benchmark numbers
cannot be reported.

Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-12-13 16:42:01 +11:00
Jim Kukunas 2aa4ee2a88 lib/raid6: fix sparse warnings in recovery functions
Make the recovery functions static to fix the following sparse warnings:

lib/raid6/recov.c:25:6: warning: symbol 'raid6_2data_recov_intx1' was
not declared. Should it be static?
lib/raid6/recov.c:69:6: warning: symbol 'raid6_datap_recov_intx1' was
not declared. Should it be static?
lib/raid6/recov_ssse3.c:22:6: warning: symbol 'raid6_2data_recov_ssse3'
was not declared. Should it be static?
lib/raid6/recov_ssse3.c:197:6: warning: symbol 'raid6_datap_recov_ssse3'
was not declared. Should it be static?

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-05-28 14:10:22 +10:00
Jim Kukunas 96e67703e7 lib/raid6: cleanup gen_syndrome function selection
Reorders functions in raid6_algos as well as the preference check
to reduce the number of functions tested on initialization.

Also, creates symmetry between choosing the gen_syndrome functions
and choosing the recovery functions.

Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-05-22 13:54:24 +10:00
Jim Kukunas 2dbf708448 lib/raid6: update test program for recovery functions
Test each combination of recovery and syndrome generation
functions.

Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-05-22 13:54:23 +10:00
Jim Kukunas 048a8b8c89 lib/raid6: Add SSSE3 optimized recovery functions
Add SSSE3 optimized recovery functions, as well as a system
for selecting the most appropriate recovery functions to use.

Originally-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-05-22 13:54:18 +10:00
Jim Kukunas f674ef7b43 lib/raid6: fix test program build
<linux/module.h> drags in headers which are not visible to userspace,
thus breaking the build for the test program.

Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2012-05-22 13:54:16 +10:00
David Howells 9ffc93f203 Remove all #inclusions of asm/system.h
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`

Signed-off-by: David Howells <dhowells@redhat.com>
2012-03-28 18:30:03 +01:00
David Howells ae3a197e3d Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PowerPC.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: linuxppc-dev@lists.ozlabs.org
2012-03-28 18:30:02 +01:00
Paul Gortmaker daaa5f7cbe md: Add in export.h for files using EXPORT_SYMBOL
These files were getting the defines for EXPORT_SYMBOL because
device.h was including module.h.  But we are going to put an
end to that.  So add the proper export.h include now.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:19 -04:00
Paul Gortmaker 056075c764 md: Add module.h to all files using it implicitly
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore.  Make sure the modular drivers in md dir
are actually calling out for <module.h> explicitly in advance.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:18 -04:00
Dan McGee bd860c53d4 lib/raid6: Fix filename emitted in generated code
The files were renamed in commit cc4589ebf; fix the name in the file
itself.

Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2011-10-20 11:27:50 +11:00
NeilBrown 7c44ece988 Move .gitignore from drivers/md to lib/raid6
Another missing bit of the raid6 -> /lib move.

Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-08-30 17:35:52 +10:00
NeilBrown a8e026c785 Further tidyup of raid6 naming in lib/raid6
Rename raid6/raid6x86.h to raid6/x86.h
and modify some comments.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-08-12 06:44:54 +10:00
NeilBrown d5302fe41f Make lib/raid6/test build correctly.
Some bit-rot needs to be cleaned out.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-08-12 06:38:24 +10:00
David Woodhouse cc4589ebfa Rename raid6 files now they're in a 'raid6' directory.
Linus asks 'why "raid6" twice?'. No reason.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-11 00:19:05 +01:00
David Woodhouse 2144381da4 Merge branch 'async' of macbook:git/btrfs-unstable
Conflicts:
	drivers/md/Makefile
	lib/raid6/unroll.pl
2010-08-09 10:36:44 +01:00
David Woodhouse f5e70d0fe3 md: Factor out RAID6 algorithms into lib/
We'll want to use these in btrfs too.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-10-29 14:38:47 +00:00