The driver shutdown callback (which sends EDL_SOC_RESET to the device
over serdev) should not be invoked when HCI device is not open (e.g. if
hci_dev_open_sync() failed), because the serdev and its TTY are not open
either. Also skip this step if device is powered off
(qca_power_shutdown()).
The shutdown callback causes use-after-free during system reboot with
Qualcomm Atheros Bluetooth:
Unable to handle kernel paging request at virtual address
0072662f67726fd7
...
CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G W
6.1.0-rt5-00325-g8a5f56bcfcca #8
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
tty_driver_flush_buffer+0x4/0x30
serdev_device_write_flush+0x24/0x34
qca_serdev_shutdown+0x80/0x130 [hci_uart]
device_shutdown+0x15c/0x260
kernel_restart+0x48/0xac
KASAN report:
BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50
Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1
CPU: 7 PID: 1 Comm: systemd-shutdow Not tainted
6.1.0-next-20221220-00014-gb85aaf97fb01-dirty #28
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xdc/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x68/0x84
print_report+0x188/0x488
kasan_report+0xa4/0xf0
__asan_load8+0x80/0xac
tty_driver_flush_buffer+0x1c/0x50
ttyport_write_flush+0x34/0x44
serdev_device_write_flush+0x48/0x60
qca_serdev_shutdown+0x124/0x274
device_shutdown+0x1e8/0x350
kernel_restart+0x48/0xb0
__do_sys_reboot+0x244/0x2d0
__arm64_sys_reboot+0x54/0x70
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x44/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xbc/0x140
el0t_64_sync+0x190/0x194
Fixes: 7e7bbddd02 ("Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 43eb12d789 ("Bluetooth: Fix/implement Three-wire reliable packet sending")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 166d2f6a43 ("[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 803b58367f ("Bluetooth: btusb: Implement driver internal packet reassembly")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
skb allocated by __hci_cmd_sync would not be used whether in checking
for supported iBT hardware variants or after, we should free it in all
error branches, this patch makes the case read version failed or default
error case free skb before return.
Fixes: c86c7285bb ("Bluetooth: btintel: Fix the legacy bootloader returns tlv based version")
Fixes: 019a1caa7f ("Bluetooth: btintel: Refactoring setup routine for bootloader devices")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btintel.c:1041:38: warning: cast to restricted __le32
drivers/bluetooth/btintel.c:1786:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1795:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1796:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1797:25: warning: cast to restricted __le16
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btusb.c:3426:28: warning: cast to restricted __le32
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2245:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2249:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2253:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2257:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2261:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2267:18: warning: cast to restricted __le16
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
after probe() failure.
Fixes: ab80b2cec05f ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom BCM4377/4378/4387 are dual WiFi/Bluetooth boards found in Apple
machines. This driver adds support for the Bluetooth function which
exposes a shared memory IPC protocol over PCIe to tunnel HCI traffic.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress.
This chip is present e.g. on muRata 2AE module.
This chip has additional quirk where the HCI command 0xfc45, used on
older chips to switch UART clock from 24 MHz to 48 MHz, to support
baudrates over 3 Mbdps, is no longer recognized by this newer chip.
This newer chip can configure the 4 Mbdps baudrate without the need
to issue HCI command 0xfc45, so add flag to indicate this and do not
issue the command on this chip to avoid failure to set 4 Mbdps baud
rate.
It is not clear whether there is a way to determine which chip does
and which chip does not support the HCI command 0xfc45, other than
trial and error.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add IDs to usb_device_id table for WCN6855. IDs are extracted from Windows
driver of Lenovo Thinkpad T14 Gen 2(Driver version 1.0.0.1205 Windows 10)
Windows driver download address:
https://pcsupport.lenovo.com/us/en/products/laptops-and-netbooks/
thinkpad-t-series-laptops/thinkpad-t14-gen-2-type-20xk-20xl/downloads
/driver-list/
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
poll_sync has been proven to fix races of USB data and event endpoints
so this enables it by default.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
This adds CONFIG_BT_HCIBTUSB_POLL_SYNC which can be used to set the
default behavior of Bluetooth USB controller with respect to poll
synchronization of its endpoits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
The current version of the configuration structure has unaligned
16-bit fields, but according to the specification [1], access to
the configuration space must be aligned.
Add a second, aligned version of the configuration structure
and a new feature bit indicating that this version is being used.
[1] https://docs.oasis-open.org/virtio/virtio/v1.1/virtio-v1.1.pdf
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Only assign hdev->wakeup if the serial port supports wakeup. Otherwise
it will fall back to the hci_uart_wakeup or the behavior that can be
overridden before calling the hci_uart_register_device().
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For USB ALT 6 settings some Realtek chips need to transmit mSBC data
continuously without the zero length of USB packets.
In this commit, create BTUSB_ALT6_CONTINUOUS_TX to manage the behavior.
Therefore, create REALTEK_ALT6_CONTINUOUS_TX_CHIP to manage the specific
chip model for the behavior.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds a data structure for btrealtek object, and the
definition of vendor behavior flags. It also adds macros to set/test/get
the flags.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device removal is clearly out of virtio spec: it attempts to remove
unused buffers from a VQ before invoking device reset. To fix, make
open/close NOPs and do all cleanup/setup in probe/remove.
NB: This is a hacky way to handle this - virtbt_{open,close} as NOP is
not really what a driver is supposed to be doing. These are transport
enable/disable callbacks from the BT core towards the driver. It maps to
a device being enabled/disabled by something like bluetoothd for
example. So if disabled, users expect that no resources/queues are in
use. It does work with all other transports like USB, SDIO, UART etc.
There should be no buffer used if the device is powered off. We also
don’t have any USB URBs in-flight if the transport is not active.
The way to implement a proper fix would be using vq reset if supported,
or even using a full device reset.
The cost of the hack is a single skb wasted on an unused bt device.
NB2: with this fix in place driver still suffers from a race condition
if an interrupt triggers while device is being reset. To fix, in the
virtbt_close() callback we should deactivate all interrupts. To be
fixed.
squashed fixup: bluetooth: virtio_bt: fix an error code in probe()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220811080943.198245-1-mst@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
The USB interface between the host and the bluetooth adapter used for
SCO packets uses an USB isochronous endpoint with a fragmentation scheme
that does not tolerate errors. Except USB isochronous transfers do
not provide a reliable stream with guaranteed delivery. (There is no
retry on error, see USB spec v2.0 5.6 and 8.5.5.)
To fragment a packet, the bluetooth HCI simply splits it in parts and
transfer them as-is. The receiver is expected to reconstruct the packet
by assuming the first fragment contains the header and parsing its size
field. There is no error detection either.
If a fragment is lost, the end result is that the kernel is no longer
synchronized and will pass malformed data to the upper layers, since it
has no way to tell if the first fragment is an actual first fragment or
a continuation fragment. Resynchronization can only happen by luck and
requires an unbounded amount of time.
The typical symptom for a HSP/HFP bluetooth headset is that the
microphone stops working and dmesg contains piles of rate-limited
"Bluetooth: hci0: SCO packet for unknown connection handle XXXX"
errors for an indeterminate amount of time, until the kernel accidentally
resynchronize.
A workaround is to ask the upper layer to prevalidate the first fragment
header. This is not possible with user channels so this workaround is
disabled in this case.
This problem is the most severe when using an ath3k adapter on an i.MX 6
board, where packet loss occur regularly, possibly because it is an USB1
device connected on an USB2 hub and this is a special case requiring
split transactions.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On cmd_timeout with no reset_gpio, reset the USB port as a last
resort.
This patch changes the behavior of btusb_intel_cmd_timeout and
btusb_rtl_cmd_timeout.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In case of suspend/resume and HCI_RESET (BT On and Off),
ISOC endpoint set to alt setting 0 when no SCO connection exists.
This patch shall avoid resetting of ISOC endpoint to alt setting to 0.
Signed-off-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
- Core:
- The timer_shutdown[_sync]() infrastructure:
Tearing down timers can be tedious when there are circular
dependencies to other things which need to be torn down. A prime
example is timer and workqueue where the timer schedules work and the
work arms the timer.
What needs to prevented is that pending work which is drained via
destroy_workqueue() does not rearm the previously shutdown
timer. Nothing in that shutdown sequence relies on the timer being
functional.
The conclusion was that the semantics of timer_shutdown_sync() should
be:
- timer is not enqueued
- timer callback is not running
- timer cannot be rearmed
Preventing the rearming of shutdown timers is done by discarding rearm
attempts silently. A warning for the case that a rearm attempt of a
shutdown timer is detected would not be really helpful because it's
entirely unclear how it should be acted upon. The only way to address
such a case is to add 'if (in_shutdown)' conditionals all over the
place. This is error prone and in most cases of teardown not required
all.
- The real fix for the bluetooth HCI teardown based on
timer_shutdown_sync().
A larger scale conversion to timer_shutdown_sync() is work in
progress.
- Consolidation of VDSO time namespace helper functions
- Small fixes for timer and timerqueue
- Drivers:
- Prevent integer overflow on the XGene-1 TVAL register which causes
an never ending interrupt storm.
- The usual set of new device tree bindings
- Small fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=JlDe
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2022-12-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for timers, timekeeping and drivers:
Core:
- The timer_shutdown[_sync]() infrastructure:
Tearing down timers can be tedious when there are circular
dependencies to other things which need to be torn down. A prime
example is timer and workqueue where the timer schedules work and
the work arms the timer.
What needs to prevented is that pending work which is drained via
destroy_workqueue() does not rearm the previously shutdown timer.
Nothing in that shutdown sequence relies on the timer being
functional.
The conclusion was that the semantics of timer_shutdown_sync()
should be:
- timer is not enqueued
- timer callback is not running
- timer cannot be rearmed
Preventing the rearming of shutdown timers is done by discarding
rearm attempts silently.
A warning for the case that a rearm attempt of a shutdown timer is
detected would not be really helpful because it's entirely unclear
how it should be acted upon. The only way to address such a case is
to add 'if (in_shutdown)' conditionals all over the place. This is
error prone and in most cases of teardown not required all.
- The real fix for the bluetooth HCI teardown based on
timer_shutdown_sync().
A larger scale conversion to timer_shutdown_sync() is work in
progress.
- Consolidation of VDSO time namespace helper functions
- Small fixes for timer and timerqueue
Drivers:
- Prevent integer overflow on the XGene-1 TVAL register which causes
an never ending interrupt storm.
- The usual set of new device tree bindings
- Small fixes and improvements all over the place"
* tag 'timers-core-2022-12-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
dt-bindings: timer: renesas,cmt: Add r8a779g0 CMT support
dt-bindings: timer: renesas,tmu: Add r8a779g0 support
clocksource/drivers/arm_arch_timer: Use kstrtobool() instead of strtobool()
clocksource/drivers/timer-ti-dm: Fix missing clk_disable_unprepare in dmtimer_systimer_init_clock()
clocksource/drivers/timer-ti-dm: Clear settings on probe and free
clocksource/drivers/timer-ti-dm: Make timer_get_irq static
clocksource/drivers/timer-ti-dm: Fix warning for omap_timer_match
clocksource/drivers/arm_arch_timer: Fix XGene-1 TVAL register math error
clocksource/drivers/timer-npcm7xx: Enable timer 1 clock before use
dt-bindings: timer: nuvoton,npcm7xx-timer: Allow specifying all clocks
dt-bindings: timer: rockchip: Add rockchip,rk3128-timer
clockevents: Repair kernel-doc for clockevent_delta2ns()
clocksource/drivers/ingenic-ost: Define pm functions properly in platform_driver struct
clocksource/drivers/sh_cmt: Access registers according to spec
vdso/timens: Refactor copy-pasted find_timens_vvar_page() helper into one copy
Bluetooth: hci_qca: Fix the teardown problem for real
timers: Update the documentation to reflect on the new timer_shutdown() API
timers: Provide timer_shutdown[_sync]()
timers: Add shutdown mechanism to the internal functions
timers: Split [try_to_]del_timer[_sync]() to prepare for shutdown mode
...
The rationale of showing this is that it's potentially critical
information to diagnose and find more CSR compatibility bugs in the
future and it will save a lot of headaches.
Given that clones come from a wide array of vendors (some are actually
Barrot, some are something else) and these numbers are what let us find
differences between actual and fake ones, it will be immensely helpful
to scour the Internet looking for this pattern and building an actual
database to find correlations and improve the checks.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A patch series by a Qualcomm engineer essentially removed my
quirk/workaround because they thought it was unnecessary.
It wasn't, and it broke everything again:
https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=*
He argues that the quirk is not necessary because the code should check
if the dongle says if it's supported or not. The problem is that for
these Chinese CSR clones they say that it would work:
= New Index: 00:00:00:00:00:00 (Primary,USB,hci0)
= Open Index: 00:00:00:00:00:00
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
> [hci0] 11.276039
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810)
LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312)
Manufacturer: Cambridge Silicon Radio (10)
...
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 68
> [hci0] 11.668030
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 163 entries
...
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
...
...
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
= Close Index: 00:1A:7D:DA:71:XX
So bring it back wholesale.
Fixes: 63b1a7dd38 ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING")
Fixes: e168f69008 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR")
Fixes: 766ae2422b ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk")
Cc: stable@vger.kernel.org
Cc: Zijun Hu <quic_zijuhu@quicinc.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
While discussing solutions for the teardown problem which results from
circular dependencies between timers and workqueues, where timers schedule
work from their timer callback and workqueues arm the timers from work
items, it was discovered that the recent fix to the QCA code is incorrect.
That commit fixes the obvious problem of using del_timer() instead of
del_timer_sync() and reorders the teardown calls to
destroy_workqueue(wq);
del_timer_sync(t);
This makes it less likely to explode, but it's still broken:
destroy_workqueue(wq);
/* After this point @wq cannot be touched anymore */
---> timer expires
queue_work(wq) <---- Results in a NULL pointer dereference
deep in the work queue core code.
del_timer_sync(t);
Use the new timer_shutdown_sync() function to ensure that the timers are
disarmed, no timer callbacks are running and the timers cannot be armed
again. This restores the original teardown sequence:
timer_shutdown_sync(t);
destroy_workqueue(wq);
which is now correct because the timer core silently ignores potential
rearming attempts which can happen when destroy_workqueue() drains pending
work before mopping up the workqueue.
Fixes: 72ef98445a ("Bluetooth: hci_qca: Use del_timer_sync() before freeing")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Acked-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/all/87iljhsftt.ffs@tglx
Link: https://lore.kernel.org/r/20221123201625.435907114@linutronix.de
By using skb_put we ensure that skb->tail is set
correctly. Currently, skb->tail is always zero, which
leads to errors, such as the following page fault in
rfcomm_recv_frame:
BUG: unable to handle page fault for address: ffffed1021de29ff
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751)
Fixes: afd2daa26c ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
syzbot is reporting NULL pointer dereference at hci_uart_tty_close() [1],
for rcu_sync_enter() is called without rcu_sync_init() due to
hci_uart_tty_open() ignoring percpu_init_rwsem() failure.
While we are at it, fix that hci_uart_register_device() ignores
percpu_init_rwsem() failure and hci_uart_unregister_device() does not
call percpu_free_rwsem().
Link: https://syzkaller.appspot.com/bug?extid=576dfca25381fb6fbc5f [1]
Reported-by: syzbot <syzbot+576dfca25381fb6fbc5f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 67d2f8781b ("Bluetooth: hci_ldisc: Allow sleeping while proto locks are held.")
Fixes: d73e172816 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
HarrrisonPeak, CyclonePeak, SnowFieldPeak and SandyPeak controllers
are marked to support HCI_QUIRK_LE_STATES.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hardware variant for Magnetor core (CNVi) is added.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Based on photos available from the FCC, all currently supported RTL8761B
series USB dongles have the same chip: RTL8761BUV.
rtl8761bu is often used to refer to this chip.
rtl8761b sometimes refers to this chip, and other times to its
UART variant (RTL8761BTV).
+----------------+---------+---------+---------------+
| Dongle | USB VID | USB PID | FCC ID |
+----------------+---------+---------+---------------+
| ASUS USB-BT500 | 0x0b05 | 0x190e | MSQ-USBBTJB00 |
| TP-Link UB500 | 0x2357 | 0x0604 | 2AXJ4UB500 |
| EDUP EP-B3519 | | | 2AHRD-EPB3519 |
| EDUP EP-B3536 | | | 2AHRDEP-B3536 |
| UGREEN CM390 | | | 2AQI5-CM390 |
+----------------+---------+---------+---------------+
Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Fix up the packet type if ISO packets are sent over the bulk endpoint.
Note: This is a stopgap since the Bluetooth specification currently
doesn't define any endpoint to transport ISO packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Krzysztof Kozlowski
Steven Rostedt (Google)
Linus Torvalds
Yang Yingliang
Wang ShaoBo
Luiz Augusto von Dentz
Gongwei Li
Artem Lukyanov
Andy Chi
Raman Varabets
Sven Peter
Marek Vasut
Shengyu Qu
Igor Skalkin
Zhengping Jiang
Hilda Wu
Michael S. Tsirkin
Nicolas Cavallari
Archie Pusaka
Chethan Tumkur Narayan
Ismael Ferreras Morezuelas
Thomas Gleixner
Soenke Huster
Tetsuo Handa
Daniel Golle
Sean Wang
Kiran K
Chris Lu
Larry Finger
Szabolcs Sipos
Max Chou
Fae