Граф коммитов

64 Коммитов

Автор SHA1 Сообщение Дата
Dan Carpenter 63e144c9d6 ti-st: clean up data types (fix harmless memory corruption)
The big issue here is:

	of_property_read_u32(np, "flow_cntrl", (u32 *)&dt_pdata->flow_cntrl);

"->flow_cntrl" is a char so when we write a 32 bit number to it then it
corrupts past the end of the char.  It's probably hard to notice because
the struct has padding so the code works on little endian systems. But
on a big endian system the code would fail and on a 64 bit, big endian
systems then "nshutdown_gpio" and "baud_rate" would be buggy as well.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-03 15:48:51 -08:00
Nicholas Mc Guire 3f46d81ae1 misc: ti-st: add handling of the signal case
if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.

Only the timeout case was being handled, the signal case
(-ERESTARTSYS) was treated just like the case of successful
completion, which is most likely not reasonable.

read_local_version() is called from download_firmware() where
it checks for !=0 return, so the error handling logic should be
preserved correctly.

download_firmware() is called from st_kim_start() which is
checking for !=0 return, so the error handling logic should be
preserved correctly

Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-25 09:18:00 -08:00
Gigi Joseph 0ec0cf1920 drivers:misc:ti-st: protect against bad packets
We encounter situations where we got bad packet type from the
UART (probably due to platform problem or UART driver issues)
which caused us out of boundary array access,
which eventually led to kernel panic.

Signed-off-by: Amir Ayun <amira@ti.com>
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Leonid Iziumtsev <x0153368@ti.com>
Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-12 05:04:11 -08:00
Gigi Joseph 868eba8e13 drivers: misc: ti-st: fix null pointer exception in st_kim_ref()
st_kim_ref() does not take care of the fact that platform_get_drvdata() might return NULL. On AM437x EVM, this causes the platform to stop booting as soon as the module is inserted.

This patch fixes the issue by checking for NULL return value. Oops log follows.

I have not tested BT functionality after this patch. But at least the platform boots now.

[   12.675697] Unable to handle kernel NULL pointer dereference at virtual address 0000005c
[   12.684310] pgd = c0004000
[   12.687157] [0000005c] *pgd=00000000
[   12.690927] Internal error: Oops: 17 [#1] SMP ARM
[   12.695873] Modules linked in: btwilink bluetooth ti_vpfe dwc3(+) ov2659 videobuf2_core v4l2_common videodev ti_am335x_adc 6lowpan_iphc matrix_keypad panel_dpi kfifo_buf pixcir_i2c_ts media industrialio videobuf2_dma_contig c_can_platform videobuf2_memops dwc3_omap c_can can_dev
[   12.721969] CPU: 0 PID: 1235 Comm: kworker/u3:0 Not tainted 3.14.25-02445-g9036ac6daed6 #128
[   12.730937] Workqueue: hci0 hci_power_on [bluetooth]
[   12.736165] task: ebd93b40 ti: ecd7c000 task.ti: ecd7c000
[   12.741856] PC is at st_kim_ref+0x30/0x40
[   12.746071] LR is at st_kim_ref+0x30/0x40
[   12.750289] pc : [<c03caf58>]    lr : [<c03caf58>]    psr: a0000013
[   12.750289] sp : ecd7de08  ip : ecd7de08  fp : ecd7de1c
[   12.762365] r10: bf1e710c  r9 : bf1e70ec  r8 : bf1e7964
[   12.767858] r7 : ebd2fd50  r6 : bf1e7964  r5 : 00000000  r4 : ecd7de24
[   12.774723] r3 : c0957208  r2 : 00000000  r1 : c0957208  r0 : 00000000
[   12.781589] Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[   12.789274] Control: 10c5387d  Table: abde4059  DAC: 00000015
[   12.795315] Process kworker/u3:0 (pid: 1235, stack limit = 0xecd7c248)

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-12 05:04:11 -08:00
Gigi Joseph c6ec0fb400 drivers: misc: ti-st: fix debugfs creation error handling
In case the debugfs creation fails the whole init process was failing.
There is no need to do this as the shared transport can work without it.
Fix it so it just reports the failure and continue.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-12 05:04:11 -08:00
Gigi Joseph 4b4aa3ab98 st_kim: allow suspend if callback is not registered
Suspend/resume was failing if callbacks were not registered.
As it is ok not to do anything when suspending fix this
so it soen't return an error and allow the system to suspend.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-12 05:04:10 -08:00
Gigi Joseph 46d0d33350 ti-st: add device tree support
When using device tree, driver configuration data need to be read from
device node.
Add support for getting the platform data information from the device
tree information stored in the .dtb file in case it exists.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: bvijay <bvijay@ti.com>
Diff rendering mode:inlineside by side

Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-12 05:04:10 -08:00
Wolfram Sang 17149e4c86 misc: ti-st: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:20:56 +02:00
Lee Jones e4ebe5fe2d misc: st_core: Protect unsigned value against becoming negative
Coverity reported:
  This less-than-zero comparison of an unsigned value is never true.

In answer to that, we only ever decrement if protos_registered is
positive.  We can subsequently remove the paranoid checking during
unregister.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-23 23:14:28 -07:00
Enric Balletbo i Serra 4dcc2ab3f8 drivers/misc/ti-st: Load firmware from ti-connectivity directory.
Looks like the default location for TI firmware is inside the ti-connectivity
directory, to be coherent with other firmware request used by TI drivers, load
the TIInit firmware from this directory instead of /lib/firmware directly.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-23 17:02:49 -07:00
Robin van der Gracht 3768528af3 ti-st: st-kim: Dont let probe fail when debugfs is disabled
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09 17:33:25 -07:00
Paul Gortmaker e2527ec369 drivers/misc: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-07 15:10:19 -08:00
Peter Hurley 94459a975b drivers/misc/ti-st: Prefer tty_driver_flush_buffer
The tty core provides an interface for flushing the driver's
write buffer: tty_driver_flush_buffer(); prefer the provided
interface over open-coded. Open-coding can lead to errors
such as the duplicated call in the st_kim driver.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04 20:23:51 -08:00
Wolfram Sang 16735d022f tree-wide: use reinit_completion instead of INIT_COMPLETION
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.

[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-11-15 09:32:21 +09:00
Oleksandr Kozaruk 3a2d3d213d drivers: misc: ti-st: fix potential race if st_kim_start fails
If st_kim_start() fails registered protocols should be removed. This is
done by calling st_reg_complete(), which as comment states is called
with spin lock held. But in st_register() when st_kim_start fails it
is called without holding spin lock, creating possibility of concurrent
access to st_gdata data members.
Hold spin lock while calling st_reg_complete if st_kim_start() fails.

Signed-off-by: Oleksandr Kozaruk <oleksandr.kozaruk@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-30 12:08:04 -07:00
Jingoo Han 9093ca8891 misc: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-30 21:46:15 +09:00
Linus Torvalds 7ed214ac20 Char/Misc driver patches for 3.9-rc1
Here's the big char/misc driver patches for 3.9-rc1.
 
 Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
 extcon, vmci, etc.).
 
 All of these have been in the linux-next tree for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
 x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
 =i5HH
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver patches from Greg Kroah-Hartman:
 "Here's the big char/misc driver patches for 3.9-rc1.

  Nothing major here, just lots of different driver updates (mei,
  hyperv, ipack, extcon, vmci, etc.).

  All of these have been in the linux-next tree for a while."

* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
  w1: w1_therm: Add force-pullup option for "broken" sensors
  w1: ds2482: Added 1-Wire pull-up support to the driver
  vme: add missing put_device() after device_register() fails
  extcon: max8997: Use workqueue to check cable state after completing boot of platform
  extcon: max8997: Set default UART/USB path on probe
  extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
  extcon: max8997: Set default of ADC debounce time during initialization
  extcon: max8997: Remove duplicate code related to set H/W line path
  extcon: max8997: Move defined constant to header file
  extcon: max77693: Make max77693_extcon_cable static
  extcon: max8997: Remove unreachable code
  extcon: max8997: Make max8997_extcon_cable static
  extcon: max77693: Remove unnecessary goto statement to improve readability
  extcon: max77693: Convert to devm_input_allocate_device()
  extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
  CREDITS: update email and address of Harald Hoyer
  extcon: arizona: Use MICDET for final microphone identification
  extcon: arizona: Always take the first HPDET reading as the final one
  extcon: arizona: Clear _trig_sts bits after jack detection
  extcon: arizona: Don't HPDET magic when headphones are enabled
  ...
2013-02-21 13:57:13 -08:00
Greg Kroah-Hartman 9f9cba810f Merge 3.8-rc5 into tty-next
This resolves a number of tty driver merge issues found in linux-next

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-25 13:27:36 -08:00
Luciano Coelho a7e2ca1703 Revert "drivers/misc/ti-st: remove gpio handling"
This reverts commit eccf2979b2.

The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.

Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.

Cc: stable <stable@vger.kernel.org> [3.7]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-22 17:22:47 -08:00
Luciano Coelho 55cd0e36f6 Revert "drivers/misc/ti-st: remove gpio handling"
This reverts commit eccf2979b2.

The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.

Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.

Cc: stable <stable@vger.kernel.org> [3.7]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-21 14:29:03 -08:00
Joe Millenbach 4f73bc4dd3 tty: Added a CONFIG_TTY option to allow removal of TTY
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48

Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-18 16:15:27 -08:00
channing 25c22d5bea misc: st_core: Error triggered by convert "char" to "int"
When st driver decodes protocol index received from raw data,
it does a value convert from "char" to "int". Because it's sign
extension from bit8 to bit32, the "int" value maybe minus, in
another word, the protocol index might be minus, but driver doesn't
filter such case and may continue access memory pointed by this
minus index.

This patch is to change the variable type of index from "int"
to "unsigned char", so that it avoids do such kind of type
conversion.

cc: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-17 10:19:42 -08:00
Matthias Kaehlcke b2997387c2 misc/st_kim: Free resources in the error path of probe()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-26 16:16:35 -08:00
Wei Yongjun 35299f884a drivers:misc: ti-st: fix potential NULL pointer dereference in st_register()
Remove the pointless NULL dereference above the NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-24 15:52:29 -07:00
Matthias Kaehlcke 877cdf3949 drivers/misc/ti-st: check chip_awake NULL check
Before calling on any of the platform hooks, shared transport driver checks
for the validity of the platform hooks as to whether it is provided or not.
A wrong function was being checked for, before the chip_awake hook was called
by the HCI-LL sleep logic handler. This patch corrects the check.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy 8565adbc82 drivers/misc/ti-st: fix read fw version cmd
If the read firmware version response from the chip is split into multiple
frames of UART buffer being received by the host, the TI-ST driver as of today
is unable to put the pieces of response together unlike other responses.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy 537023580d drivers/misc/ti-st: use cpu friendly completions
Be nice to CPU and don't hog the resources, use a nice wait_for_interruptible
timeout for completions instead of wait_for_timeout which is
non-interruptible.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy b64365a526 drivers/misc/ti-st: chip_disable on timeout
If the communication with the WiLink breaks down for whatever reasons & the
ti-st driver is unable to un-install the line-discipline during clean-up in
st_kim_stop, the GPIO should be held low (BT_EN=0) & the platform's chip
disable hook shall also be called.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy 27712b3928 drivers/misc/ti-st: remove sparse warnings
remove sparse warnings by assigning right storage specifiers to functions and
also clean-up the declarations in the include/linux/ti_wilink_st.h

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy eccf2979b2 drivers/misc/ti-st: remove gpio handling
A platform hook to enable/disable the chip was introduced to perform specific
activities to power-up and power-down the WL chip.
Moving the power-up/down sequence also there makes more sense, since different
platforms have begun to have their own ways to power-up/down the chip.
This patch removes all of the gpio handling done by the driver in
st_kim_start/st_kim_stop & any of the gpio request done in the probe function.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Alan Cox 5353cf089b drivers/misc/ti-st/st_core.c: missing NULL check
Addresses https://bugzilla.kernel.org/show_bug.cgi?44431

Reported-by: <rucsoftsec@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-07-30 17:25:13 -07:00
Axel Lin b00e126ffe MISC: convert drivers/misc/* to use module_platform_driver()
This patch converts the drivers in drivers/misc/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Acked-By: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-24 16:31:48 -08:00
Pavan Savoy 933aae54be drivers:misc: ti-st: DEBUG uart, baud rate mods
To debug different UARTs at different baud-rates connected to the WiLink
connectivity combo-chipset, this patch enables the debugging code so that upon
boot different UARTs at different baud-rates can be tried out to verify the
interface with WiLink.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-04 15:21:04 -08:00
Pavan Savoy 18ccecf99a drivers:misc: ti-st: flush UART upon fw failure
Upon failure to read firmware version from chip or upon failure in responses
to firmware download the UART needs to be flushed of its existing buffers so
that the UIM can restart UART properly.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-04 15:21:04 -08:00
Pavan Savoy bfb88d6c91 drivers:misc: ti-st: protect registrations
Concurrent access to UART2/combo-interface by multiple protocol drivers such
as BT, FM and GPS caused issues during firmware download failure cases or
cases when the firmware download took longer than usual.

This was because of un-safe access to protos_registered & st_states.
Protecting this will also make the registration complete callback un-safe for
sleep.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-04 15:21:03 -08:00
Paul Gortmaker eb12a679b2 drivers/misc: Add module.h to files who are really modular.
These files really need the full module.h header file present, but
were just getting it implicitly before.  Fix it up in advance so we
avoid build failures once the cleanup commit is present.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:53 -04:00
Pavan Savoy 651d62a8b0 drivers:misc: ti-st: fix unexpected UART close
If suppose the UIM were to die and hence UART were to close when the
Bluetooth/FM or GPS is turned on, prep the ST for a state where-in if
the UIM comes back up, Bluetooth/FM/GPS can be turned on.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:35 -07:00
Pavan Savoy 76ff0e64d4 drivers:misc: ti-st: free skb on firmware download
If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:34 -07:00
Pavan Savoy d0344ef670 drivers:misc: ti-st: wait for completion at fail
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:34 -07:00
Pavan Savoy 2f81a02ce0 drivers:misc: ti-st: reinit completion before send
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.

So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:33 -07:00
Vijay Badawadagi 78bb9697e2 drivers:misc: ti-st: fail-safe on wrong pkt type
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.

In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:33 -07:00
Pavan Savoy 74a4fcf19e drivers:misc: ti-st: reinit completion on ver read
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:32 -07:00
Pavan Savoy 0d7c5f2572 drivers:misc:ti-st: platform hooks for chip states
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.

Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:32 -07:00
Pavan Savoy 5926cef26c drivers:misc: ti-st: avoid a misleading dbg msg
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:31 -07:00
Shahar Lev 9d031d94da drivers:misc: ti-st: fix skipping of change remote baud
Before the incrementing of ptr in skip_change_remote_baud,
it points to cur_action, but the increment is done by
the size of nxt_action instead. This could cause ptr
to not point to a bts_action structure, which is
harmful for the increment of ptr done in download_firmware.
Therefore, the skipping is first done for cur_action.

Signed-off-by: Shahar Lev <shahar@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-07 10:01:18 -07:00
Steven Rostedt 7316a9f2a9 st_kim: Handle case of no device found for ID 0
Running ktest.pl, I hit this bug:

[   19.780654] BUG: unable to handle kernel NULL pointer dereference at 0000000c
[   19.780660] IP: [<c112efcd>] dev_get_drvdata+0xc/0x46
[   19.780669] *pdpt = 0000000031daf001 *pde = 0000000000000000
[   19.780673] Oops: 0000 [#1] SMP
[   19.780680] Dumping ftrace buffer:^M
[   19.780685]    (ftrace buffer empty)
[   19.780687] Modules linked in: ide_pci_generic firewire_ohci firewire_core evbug crc_itu_t e1000 ide_core i2c_i801 iTCO_wdt
[   19.780697]
[   19.780700] Pid: 346, comm: v4l_id Not tainted 2.6.39-test-02740-gcaebc16-dirty #4                  /DG965MQ
[   19.780706] EIP: 0060:[<c112efcd>] EFLAGS: 00010202 CPU: 0
[   19.780709] EIP is at dev_get_drvdata+0xc/0x46
[   19.780712] EAX: 00000008 EBX: f1e37da4 ECX: 00000000 EDX: 00000000
[   19.780715] ESI: f1c3f200 EDI: c33ec95c EBP: f1e37d80 ESP: f1e37d80
[   19.780718]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[   19.780721] Process v4l_id (pid: 346, ti=f1e36000 task=f2bc2a60 task.ti=f1e36000)
[   19.780723] Stack:
[   19.780725]  f1e37d8c c117d395 c33ec93c f1e37db4 c117a0f9 00000002 00000000 c1725e54
[   19.780732]  00000001 00000007 f2918c90 f1c3f200 c33ec95c f1e37dd4 c1789d3d 22222222
[   19.780740]  22222222 22222222 f2918c90 f1c3f200 f29194f4 f1e37de8 c178d5c4 c1725e54
[   19.780747] Call Trace:
[   19.780752]  [<c117d395>] st_kim_ref+0x28/0x41
[   19.780756]  [<c117a0f9>] st_register+0x29/0x562
[   19.780761]  [<c1725e54>] ? v4l2_open+0x111/0x1e3
[   19.780766]  [<c1789d3d>] fmc_prepare+0x97/0x424
[   19.780770]  [<c178d5c4>] fm_v4l2_fops_open+0x70/0x106
[   19.780773]  [<c1725e54>] ? v4l2_open+0x111/0x1e3
[   19.780777]  [<c1725e9b>] v4l2_open+0x158/0x1e3
[   19.780782]  [<c065173b>] chrdev_open+0x22c/0x276
[   19.780787]  [<c0647c4e>] __dentry_open+0x35c/0x581
[   19.780792]  [<c06498f9>] nameidata_to_filp+0x7c/0x96
[   19.780795]  [<c065150f>] ? cdev_put+0x57/0x57
[   19.780800]  [<c0660cad>] do_last+0x743/0x9d4
[   19.780804]  [<c065d5fc>] ? path_init+0x1ee/0x596
[   19.780808]  [<c0661481>] path_openat+0x10c/0x597
[   19.780813]  [<c05204a1>] ? trace_hardirqs_off+0x27/0x37
[   19.780817]  [<c0509651>] ? local_clock+0x78/0xc7
[   19.780821]  [<c0661945>] do_filp_open+0x39/0xc2
[   19.780827]  [<c1cabc76>] ? _raw_spin_unlock+0x4c/0x5d^M
[   19.780831]  [<c0674ccd>] ? alloc_fd+0x19e/0x1b7
[   19.780836]  [<c06499ca>] do_sys_open+0xb7/0x1bd
[   19.780840]  [<c0608eea>] ? sys_munmap+0x78/0x8d
[   19.780844]  [<c0649b06>] sys_open+0x36/0x58
[   19.780849]  [<c1cb809f>] sysenter_do_call+0x12/0x38
[   19.780852] Code: d8 2f 20 c3 01 83 15 dc 2f 20 c3 00 f0 ff 00 83 05 e0 2f 20 c3 01 83 15 e4 2f 20 c3 00 5d c3 55 89 e5 3e 8d 74 26 00 85 c0 74 28 <8b> 40 04 83 05 e8 2f 20 c3 01 83 15 ec 2f 20 c3 00 85 c0 74 13 ^M
[   19.780889] EIP: [<c112efcd>] dev_get_drvdata+0xc/0x46 SS:ESP 0068:f1e37d80
[   19.780894] CR2: 000000000000000c
[   19.780898] ---[ end trace e7d1d0f6a2d1d390 ]---

The id of 0 passed to st_kim_ref() found no device, keeping pdev null,
and causing pdev->dev cause a NULL pointer dereference. After having
st_kim_ref() check for NULL, the st_unregister() function needed to be
updated to handle the case that st_gdata was not set by the
st_kim_ref().

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-07 10:01:16 -07:00
Linus Torvalds 55db4c64ed Revert "tty: make receive_buf() return the amout of bytes received"
This reverts commit b1c43f82c5.

It was broken in so many ways, and results in random odd pty issues.

It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").

It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.

And it didn't actually work at all.  BenH bisected down odd tty behavior
to it:
  "It looks like the patch is causing some major malfunctions of the X
   server for me, possibly related to PTYs.  For example, cat'ing a
   large file in a gnome terminal hangs the kernel for -minutes- in a
   loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
   data in the quoted bits further down).

   ...

   Some more data: It -looks- like what happens is that the
   flush_to_ldisc work queue entry constantly re-queues itself (because
   the PTY is full ?) and the workqueue thread will basically loop
   forver calling it without ever scheduling, thus starving the consumer
   process that could have emptied the PTY."

which is pretty much exactly the problem we fixed in a5660b41af.

Milton Miller pointed out the 'unsigned int' issue.

Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-06-04 06:33:24 +09:00
Linus Torvalds 99dff58562 Merge branch 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
  serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
  tty/serial: Fix break handling for PORT_TEGRA
  tty/serial: Add explicit PORT_TEGRA type
  n_tracerouter and n_tracesink ldisc additions.
  Intel PTI implementaiton of MIPI 1149.7.
  Kernel documentation for the PTI feature.
  export kernel call get_task_comm().
  tty: Remove to support serial for S5P6442
  pch_phub: Support new device ML7223
  8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
  ASoC: Update cx20442 for TTY API change
  pch_uart: Support new device ML7223 IOH
  parport: Use request_muxed_region for IT87 probe and lock
  tty/serial: add support for Xilinx PS UART
  n_gsm: Use print_hex_dump_bytes
  drivers/tty/moxa.c: Put correct tty value
  TTY: tty_io, annotate locking functions
  TTY: serial_core, remove superfluous set_task_state
  TTY: serial_core, remove invalid test
  Char: moxa, fix locking in moxa_write
  ...

Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.

I did the hci_ldisc thing as an evil merge, cleaning things up.
2011-05-23 12:23:20 -07:00
Randy Dunlap 773d67903a misc: fix ti-st build issues
st_drv uses skb*() interfaces, so it should depend on NET.
It also uses GPIO interfaces, so it should depend on GPIOLIB.

st_kim.c uses syss_*() calls, so it should #include
<linux/sysfs.h>.

Fixes these observed build errors:
ERROR: "skb_queue_purge" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_pull" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_queue_tail" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "__alloc_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "kfree_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_dequeue" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_put" [drivers/misc/ti-st/st_drv.ko] undefined!

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-29 14:11:03 -07:00
Felipe Balbi b1c43f82c5 tty: make receive_buf() return the amout of bytes received
it makes it simpler to keep track of the amount of
bytes received and simplifies how flush_to_ldisc counts
the remaining bytes. It also fixes a bug of lost bytes
on n_tty when flushing too many bytes via the USB
serial gadget driver.

Tested-by: Stefan Bigler <stefan.bigler@keymile.com>
Tested-by: Toby Gray <toby.gray@realvnc.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-22 17:31:53 -07:00