SCTP incorrectly doubles rto ever time a Hearbeat chunk
is generated. However RFC 4960 states:
On an idle destination address that is allowed to heartbeat, it is
recommended that a HEARTBEAT chunk is sent once per RTO of that
destination address plus the protocol parameter 'HB.interval', with
jittering of +/- 50% of the RTO value, and exponential backoff of the
RTO if the previous HEARTBEAT is unanswered.
Essentially, of if the heartbean is unacknowledged, do we double the RTO.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sctp crc32c checksum is always generated in little endian.
So, we clean up the code to treat it as little endian and remove
all the __force casts.
Suggested by Herbert Xu.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new version of my patch, now using a module parameter instead
of a sysctl, so that the option is harder to find. Please note that,
once the module is loaded, it is still possible to change the value of
the parameter in /sys/module/sctp/parameters/, which is useful if you
want to do performance comparisons without rebooting.
Computation of SCTP checksums significantly affects the performance of
SCTP. For example, using two dual-Opteron 246 connected using a Gbe
network, it was not possible to achieve more than ~730 Mbps, compared to
941 Mbps after disabling SCTP checksums.
Unfortunately, SCTP checksum offloading in NICs is not commonly
available (yet).
By default, checksums are still enabled, of course.
Signed-off-by: Lucas Nussbaum <lucas.nussbaum@ens-lyon.fr>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between sctp_rcv() and sctp_accept() where we
have moved the association from the listening socket to the
accepted socket, but sctp_rcv() processing cached the old
socket and continues to use it.
The easy solution is to check for the socket mismatch once we've
grabed the socket lock. If we hit a mis-match, that means
that were are currently holding the lock on the listening socket,
but the association is refrencing a newly accepted socket. We need
to drop the lock on the old socket and grab the lock on the new one.
A more proper solution might be to create accepted sockets when
the new association is established, similar to TCP. That would
eliminate the race for 1-to-1 style sockets, but it would still
existing for 1-to-many sockets where a user wished to peeloff an
association. For now, we'll live with this easy solution as
it addresses the problem.
Reported-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to the retransmit code exposed a long standing
bug where it was possible for a chunk to be time stamped
after the retransmit timer was reset. This caused a rare
situation where the retrnamist timer has expired, but
nothing was marked for retrnasmission because all of
timesamps on data were less then 1 rto ago. As result,
the timer was never restarted since nothing was retransmitted,
and this resulted in a hung association that did couldn't
complete the data transfer. The solution is to timestamp
the chunk when it's added to the packet for transmission
purposes. After the packet is trsnmitted the rtx timer
is restarted. This guarantees that when the timer expires,
there will be data to retransmit.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62aeaff5cc
(sctp: Start T3-RTX timer when fast retransmitting lowest TSN)
introduced a regression where it was possible to forcibly
restart the sctp retransmit timer at the transmission of any
new chunk. This resulted in much longer timeout times and
sometimes hung sctp connections.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The latest ietf socket extensions API draft said:
8.1.21. Set or Get the SCTP Partial Delivery Point
Note also that the call will fail if the user attempts to set
this value larger than the socket receive buffer size.
This patch add this validity check for SCTP_PARTIAL_DELIVERY_POINT
socket option.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If FWD-TSN chunk is received with bad stream ID, the sctp will not do the
validity check, this may cause memory overflow when overwrite the TSN of
the stream ID.
The FORWARD-TSN chunk is like this:
FORWARD-TSN chunk
Type = 192
Flags = 0
Length = 172
NewTSN = 99
Stream = 10000
StreamSequence = 0xFFFF
This patch fix this problem by discard the chunk if stream ID is not
less than MIS.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement socket option SCTP_GET_ASSOC_NUMBER of the latest ietf socket
extensions API draft.
8.2.5. Get the Current Number of Associations (SCTP_GET_ASSOC_NUMBER)
This option gets the current number of associations that are attached
to a one-to-many style socket. The option value is an uint32_t.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just fix a typo in socket.c.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brings maxseg socket option set/get into line with the latest ietf socket
extensions API draft, while maintaining backwards compatibility.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing label when CONFIG_PROC_FS=n:
net/sctp/protocol.c: In function 'sctp_proc_init':
net/sctp/protocol.c:106: error: label 'out_nomem' used but not defined
make[3]: *** [net/sctp/protocol.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using one atomic_t per protocol, use a percpu_counter
for "sockets_allocated", to reduce cache line contention on
heavy duty network servers.
Note : We revert commit (248969ae31
net: af_unix can make unix_nr_socks visbile in /proc),
since it is not anymore used after sock_prot_inuse_add() addition
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prot->destroy is not called with BH disabled. So we must add
explicit BH disable around call to sock_prot_inuse_add()
in sctp_destroy_sock()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rule of calling sock_prot_inuse_add() is that BHs must
be disabled. Some new calls were added where this was not
true and this tiggers warnings as reported by Ilpo.
Fix this by adding explicit BH disabling around those call sites.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a preparation to namespace conversion of /proc/net/protocols
In order to have relevant information for SCTP protocols, we should use
sock_prot_inuse_add() to update a (percpu and pernamespace) counter of
inuse sockets.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once an endpoint has reached the SHUTDOWN-RECEIVED state,
it MUST NOT send a SHUTDOWN in response to a ULP request.
The Cumulative TSN Ack of the received SHUTDOWN chunk
MUST be processed.
This patch fix to process Cumulative TSN Ack of the received
SHUTDOWN chunk in SHUTDOWN_RECEIVED state.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SHUTDOWN is received in SHUTDOWN-PENDING state, enpoint should enter
the SHUTDOWN-RECEIVED state and check the Cumulative TSN Ack field of
the SHUTDOWN chunk (RFC 4960 Section 9.2). If the SHUTDOWN chunk can
acknowledge all of the send DATA chunks, SHUTDOWN-ACK should be sent.
But now endpoint just silently discarded the SHUTDOWN chunk.
SHUTDOWN received in SHUTDOWN-PENDING state can happend when the last
SACK is lost by network, or the SHUTDOWN chunk can acknowledge all of
the received DATA chunks. The packet sequence(SACK lost) is like this:
Endpoint A Endpoint B ULP
(ESTABLISHED) (ESTABLISHED)
<----------- DATA
<--- shutdown
Enter SHUTDOWN-PENDING state
SACK ----lost---->
SHUTDOWN(*1) ------------>
<----------- SHUTDOWN-ACK
(*1) silently discarded now.
This patch fix to handle SHUTDOWN in SHUTDOWN-PENDING state as the same
as ESTABLISHED state.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SHUTDOWN chunk is received Cumulative TSN Ack beyond the max tsn currently
send, SHUTDOWN chunk be accepted and the association will be broken. New data
is send, but after received SACK it will be drop because TSN in SACK is less
than the Cumulative TSN, data will be retrans again and again even if correct
SACK is received.
The packet sequence is like this:
Endpoint A Endpoint B ULP
(ESTABLISHED) (ESTABLISHED)
<----------- DATA (TSN=x-1)
<----------- DATA (TSN=x)
SHUTDOWN -----------> (Now Cumulative TSN=x+1000)
(TSN=x+1000)
<----------- DATA (TSN=x+1)
SACK -----------> drop the SACK
(TSN=x+1)
<----------- DATA (TSN=x+1)(retrans)
This patch fix this problem by terminating the association and respond to
the sender with an ABORT.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ICMP packet too big message is received with MTU larger than current
PMTU, SCTP will still accept this ICMP message and sync the PMTU of assoc
with the wrong MTU.
Endpoing A Endpoint B
(ESTABLISHED) (ESTABLISHED)
ICMP --------->
(packet too big, MTU too larger)
sync PMTU
This patch fixed the problem by drop that ICMP message.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The T5 timer is the timer for the over-all shutdown procedure. If
this timer expires, then shutdown procedure has not completed and we
ABORT the association. We should update SCTP_MIB_ABORTED and
SCTP_MIB_CURRESTAB when aborting.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ABORT chunks require authentication and a protocol violation
is triggered, we do not tear down the association. Subsequently,
we should not increment SCTP_MIB_ABORTED.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3873 defined SCTP_MIB_CURRESTAB:
sctpCurrEstab OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of associations for which the current state is
either ESTABLISHED, SHUTDOWN-RECEIVED or SHUTDOWN-PENDING."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
If the T4 RTO timer expires many times(timeout), the association will enter
CLOSED state, so we should dec the number of SCTP_MIB_CURRESTAB, not inc the
number of SCTP_MIB_CURRESTAB.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gabs array in the sctp_tsnmap structure is only used
in one place, sctp_make_sack(). As such, carrying the
array around in the sctp_tsnmap and thus directly in
the sctp_association is rather pointless since most
of the time it's just taking up space. Now, let
sctp_make_sack create and populate it and then throw
it away when it's done.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tsn map currently use is 4K large and is stuck inside
the sctp_association structure making memory references REALLY
expensive. What we really need is at most 4K worth of bits
so the biggest map we would have is 512 bytes. Also, the
map is only really usefull when we have gaps to store and
report. As such, starting with minimal map of say 32 TSNs (bits)
should be enough for normal low-loss operations. We can grow
the map by some multiple of 32 along with some extra room any
time we receive the TSN which would put us outside of the map
boundry. As we close gaps, we can shift the map to rebase
it on the latest TSN we've seen. This saves 4088 bytes per
association just in the map alone along savings from the now
unnecessary structure members.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT perameter carries the adapatation value in network-byte
order. We need to store it in host byte order as expected
by data types and the user API.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch enables cookie-echo retransmission transport switch
feature. If COOKIE-ECHO retransmission happens, it will be sent
to the address other than the one last sent to.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
RFC3873 defined SCTP_MIB_OUTOFBLUES:
sctpOutOfBlues OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of out of the blue packets received by the host.
An out of the blue packet is an SCTP packet correctly formed,
including the proper checksum, but for which the receiver was
unable to identify an appropriate association."
REFERENCE
"Section 8.4 in RFC2960 deals with the Out-Of-The-Blue
(OOTB) packet definition and procedures."
But OOTB packet INIT, INIT-ACK and SHUTDOWN-ACK(COOKIE-WAIT or
COOKIE-ECHOED state) are not counted by SCTP_MIB_OUTOFBLUES.
Case 1(INIT):
Endpoint A Endpoint B
(CLOSED) (CLOSED)
INIT ---------->
<---------- ABORT
Case 2(INIT-ACK):
Endpoint A Endpoint B
(CLOSED) (CLOSED)
INIT-ACK ---------->
<---------- ABORT
Case 3(SHUTDOWN-ACK):
Endpoint A Endpoint B
(CLOSED) (CLOSED)
<---------- INIT
SHUTDOWN-ACK ---------->
<---------- SHUTDOWN-COMPLETE
Case 4(SHUTDOWN-ACK):
Endpoint A Endpoint B
(CLOSED) (COOKIE-ECHOED)
SHUTDOWN-ACK ---------->
<---------- SHUTDOWN-COMPLETE
This patch fixed the problem.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
RFC 4960: Section 9.2
The sender of the SHUTDOWN MAY also start an overall guard timer
'T5-shutdown-guard' to bound the overall time for the shutdown
sequence. At the expiration of this timer, the sender SHOULD abort
the association by sending an ABORT chunk. If the 'T5-shutdown-
guard' timer is used, it SHOULD be set to the recommended value of 5
times 'RTO.Max'.
The timer 'T5-shutdown-guard' is used to counter the overall time
for shutdown sequence, and it's start by the sender of the SHUTDOWN.
So timer 'T5-shutdown-guard' should be start when we send the first
SHUTDOWN chunk and enter the SHUTDOWN-SENT state, not start when we
receipt of the SHUTDOWN primitive and enter SHUTDOWN-PENDING state.
If 'T5-shutdown-guard' timer is start at SHUTDOWN-PENDING state, the
association may be ABORT while data is still transmitting.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
sctp_is_any() function that is used to check for wildcard addresses
only looks at the address itself to determine the address family.
This function is used in the API to check the address passed in from
the user. If the user simply zerroes out the sockaddr_storage and
pass that in, we'll end up failing. So, let's try harder to determine
the address family by also checking the socket if it's possible.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
sctp_chunks should be put on a diet. This is some of the low hanging
fruit that we can strip out. Changes all the __s8/__u8 flags to
bitfields. Saves 12 bytes per chunk.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Chunks placed on the retransmit list are marked as inelegible
for fast retrasnmission. Since missing indications determine
when fast reransmission is done, there is not point in calling
sctp_mark_missing() on the retransmit list since those chunks
will not be marked.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
There is a possibility of walking the transport list twice during
SACK processing when doing SFR-CACC algorithm. We can restructure
the code to only do this once.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Frist small step in optimizing SACK processing. Do not call
sctp_mark_missing() when there are no gaps reported and thus
not missing chunks.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Since call to function sctp_sf_abort_violation() need paramter 'arg' with
'struct sctp_chunk' type, it will read the chunk type and chunk length from
the chunk_hdr member of chunk. But call to sctp_sf_violation_paramlen()
always with 'struct sctp_paramhdr' type's parameter, it will be passed to
sctp_sf_abort_violation(). This may cause kernel panic.
sctp_sf_violation_paramlen()
|-- sctp_sf_abort_violation()
|-- sctp_make_abort_violation()
This patch fixed this problem. This patch also fix two place which called
sctp_sf_violation_paramlen() with wrong paramter type.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This minor cleanup simplifies later changes which will convert
struct sk_buff and friends over to using struct list_head.
Signed-off-by: David S. Miller <davem@davemloft.net>
If INIT-ACK is received with SupportedExtensions parameter which
indicates that the peer does not support AUTH, the packet will be
silently ignore, and sctp_process_init() do cleanup all of the
transports in the association.
When T1-Init timer is expires, OOPS happen while we try to choose
a different init transport.
The solution is to only clean up the non-active transports, i.e
the ones that the peer added. However, that introduces a problem
with sctp_connectx(), because we don't mark the proper state for
the transports provided by the user. So, we'll simply mark
user-provided transports as ACTIVE. That will allow INIT
retransmissions to work properly in the sctp_connectx() context
and prevent the crash.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not enable peer features like addip and auth, if they
are administratively disabled localy. If the peer resports
that he supports something that we don't, neither end can
use it so enabling it is pointless. This solves a problem
when talking to a peer that has auth and addip enabled while
we do not. Found by Andrei Pelinescu-Onciul <andrei@iptel.org>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback used to clobber the ip_summed filed which sctp then used
to figure out if it needed to do checksumming or not. Now that
loopback doesn't do that any more, sctp needs to set the ip_summed
field correctly.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich
Lucas Nussbaum
Harvey Harrison
David S. Miller
Joe Perches
Coly Li
Frederik Schwarzer
Wei Yongjun
Randy Dunlap
Eric Dumazet
Alexey Dobriyan
Denis V. Lunev
Neil Horman