-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cec_allocate_adapter never returns NULL, so just use IS_ERR instead of
PTR_ERR_OR_ZERO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The kAPI cec-pin.h header also defined data structures that did
not belong here but were private to the CEC core code.
Split that part off into a cec-pin-priv.h header.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----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=VOJs
-----END PGP SIGNATURE-----
Merge tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Core fixes:
- cec: Respond to unregistered initiators, when applicable
- dvb_frontend: only use kref after initialized
Driver-specific fixes:
- qcom, camss: Make function vfe_set_selection static
- qcom: VIDEO_QCOM_CAMSS should depend on HAS_DMA
- s5p-cec: add NACK detection support
- media: staging/imx: Fix uninitialized variable warning
- dib3000mc: i2c transfers over usb cannot be done from stack
- venus: init registered list on streamoff"
* tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dvb_frontend: only use kref after initialized
media: platform: VIDEO_QCOM_CAMSS should depend on HAS_DMA
media: cec: Respond to unregistered initiators, when applicable
media: s5p-cec: add NACK detection support
media: staging/imx: Fix uninitialized variable warning
media: qcom: camss: Make function vfe_set_selection static
media: venus: init registered list on streamoff
media: dvb: i2c transfers over usb cannot be done from stack
rc scancode drivers without change_protocol should have all
protocols enabled at all time. This was only true for cec and
ir-kbd-i2c.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH.
This is specifically meant for use with the upcoming cec-gpio driver
and makes it possible to trace when the HPD pin changes. Some HDMI
sinks do strange things with the HPD and this makes it easy to debug
this.
Note that this also moves the initialization of a devnode mutex and
list to the allocate_adapter function: if the HPD is high, then as
soon as the HPD interrupt is created an interrupt occurs and
cec_queue_pin_hpd_event() is called which requires that the devnode
mutex and list are initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use ktime_to_ns/ns_to_ktime. This makes it possible to work with older kernels
and the media_build compatibility system.
For the mainline kernel these functions are NOPs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Running CEC 1.4 compliance test we get the following error on test
11.1.6.2: "ERROR: The DUT did not broadcast a
<Report Physical Address> message to the unregistered device."
Fix this by letting GIVE_PHYSICAL_ADDR message respond to unregistered
device. Also, GIVE_DEVICE_VENDOR_ID and GIVE_FEATURES fall in the
same category so, respond also to these messages.
With this fix we pass CEC 1.4 official compliance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc-4.4.4 has issues with initialization of anonymous unions:
drivers/media/cec/cec-adap.c: In function 'cec_queue_msg_fh':
drivers/media/cec/cec-adap.c:184: error: unknown field 'lost_msgs' specified in initializer
work around this.
Fixes: 6b2bbb0874 ("media: cec: rework the cec event handling")
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current CEC pin value (0 or 1) was part of the cec_pin struct,
but that assumes that CEC pin monitoring can only be used with
a driver that uses the low-level CEC pin framework.
But hardware that has both a high-level API and can monitor the
CEC pin at low-level at the same time does not need to depend on
the cec pin framework.
To support such devices remove the cur_value field from struct cec_pin
and add a cec_pin_is_high field to cec_adapter. This also makes it
possible to drop the '#ifdef CONFIG_CEC_PIN' in cec-api.c.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the adapter is removed the cec_delete_adapter() call attempts
to set the physical address to INVALID by calling __cec_s_phys_addr()
and so disabling the adapter.
However, __cec_s_phys_addr checks if the device node was unregistered
and just returns in that case.
This means that the adap_enable callback is never called with 'false'
to disable the CEC adapter. Most drivers don't care, but some need
to do cleanup here.
Change the test so the adapter is correctly disabled, even when the
device node is unregistered.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 'Press and Hold' operation was not correctly implemented, in
particular the requirement that the repeat doesn't start until
the second identical keypress arrives. The REP_DELAY value also
had to be adjusted (see the comment in the code) to achieve the
desired behavior.
The 'enabled_protocols' field was also never set, fix that too. Since
CEC is a fixed protocol the driver has to set this field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The free_irq() function could be called from interrupt context,
which is invalid. Move this to the thread.
In the interrupt handler we just request that the thread disables
the irq. This is done through an atomic so we don't need to add
any spinlocks.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_EVENT_PIN_LOW/HIGH defines and the cec_queue_pin_event() function
did not specify that these were about CEC pin events.
Since in the future there will also be HPD pin events it is wise to rename
the event defines and function to CEC_EVENT_PIN_CEC_LOW/HIGH and
cec_queue_pin_cec_event() now before these become part of the ABI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If cec_debug >= 1 then log why the requested mode returned -EINVAL.
It can be hard to debug this since -EINVAL can be returned for many
reasons. So this should help.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow calling cec_notifier_set_phys_addr and
cec_notifier_set_phys_addr_from_edid with a NULL notifier, in which
case these functions do nothing.
Add a cec_notifier_phys_addr_invalidate helper function (the notifier
equivalent of cec_phys_addr_invalidate).
These changes simplify drm CEC driver support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The switch in cec_transmit_attempt_done() should ignore the
CEC_TX_STATUS_MAX_RETRIES status bit.
Calling this function with e.g. CEC_TX_STATUS_NACK | CEC_TX_STATUS_MAX_RETRIES
is perfectly legal and should not trigger the WARN(1).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Especially the '0.10' version number is confusing since CEC_ADAP_G_CAPS
returns a completely different version number.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some hardware does more than one attempt. So when it calls
cec_transmit_done when an error occurred it will e.g. use an error count
of 2 instead of 1.
The framework always assumed a single attempt, but now it is smarter
and will sum the counters to detect how many attempts were made.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC hardware that relies on low-level pin polling or
GPIO interrupts.
One example is the Allwinner SoC. But any GPIO-based CEC implementation can
use this as well.
A GPIO implementation is very suitable as well for debugging: it can use
interrupts to detect state changes and report it. Userspace can then verify
if the bus traffic is correct. This also makes error injection possible.
The disadvantage is that it is hard to get the timings right since linux
isn't a hard realtime system.
In general on an idle system it works quite well, but under load the timer
will miss its mark every so often.
The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics
with respect to the timer overruns.
When the adapter is unconfigured and the low-level driver supports
interrupts, then the interrupt will be used to detect changes. This should
be quite accurate. But when the adapter is configured a hrtimer has to be
used.
The hrtimer implements a state machine where for each state the code will
read the bus or drive the bus and go on to the next state. It will re-arm
the timer with a delay based on the next state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the new MONITOR_PIN mode.
Add the cec_pin_event function that the CEC pin code will call to queue pin
change events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Event handling was always fairly simplistic since there were only
two events. With the addition of pin events this needed to be redesigned.
The state_change and lost_msgs events are now core events with the
guarantee that the last state is always available. The new pin events
are a queue of events (up to 64 for each event) and the oldest event
will be dropped if the application cannot keep up. Lost events are
marked with a new event flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is needed for CEC adapters that allocate resources that have
to be freed before the cec_adapter is deleted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently the transmit_(attempt_)done and received_msg functions set
the timestamp themselves. For the upcoming low-level pin API we need
to pass this as an argument instead. So make _ts variants that allow
the caller to specify the timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel logging messes up the upcoming low-level CEC monitoring support
which is very time-sensitive. So change the debug level of this message
but keep a counter that is shown in the debugfs status log.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The transmit code would increase the sequence number first thing, even though
CEC_TRANSMIT would return an error due to a malformatted cec_msg struct later
on.
While valid behavior, this had the disadvantage of producing holes in the
sequence list that made debugging harder.
Only increase the sequence number when the whole message is validated.
When debugging (i.e. with cec-ctl -M) the sequence numbering is now nicely
increasing by 1 per message.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC version, vendor ID and OSD name were not cleared when clearing the
current set of logical addresses. This was unexpected and somewhat confusing,
so reset all these fields to their default values. Also document this since
the documentation wasn't quite clear either.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEbBAABAgAGBQJZR92EAAoJEHm+PkMAQRiGT1oH+KW2FLrRaYxtut+KyGA6l7tc
R/hFx1n9BibkjXeqD+y6/4SjRTe6/pT8Zkihv3/19eZ5algUWeQa0Hm+/455sl58
IdIXx/pzuCO3kqR3//fP9ZFD657GNDsuQ0fYnZESItFwiWQtO1TNfZD6KQjkqBdI
L3MVhDUVBZA2ZtPwC4ERei5/sToV9woykKoJ/A3+OkWjgX6w4SBimqgkSEFk4uE8
xS0pycyDZci93rJlECi1UueewdODTKSmhwdC80qvGEiYXzsC6UFtaF0Fj66XO1AL
UMjxqI/gkm5ZuCIjRsmPmJjgL5q1RT6UX/qtw9yn71XTmcgMiPW2/DF/v/OaTg==
=XbW2
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc6' into patchwork
Linux 4.12-rc6
* tag 'v4.12-rc6': (813 commits)
Linux 4.12-rc6
mm: larger stack guard gap, between vmas
virtio_balloon: disable VIOMMU support
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
perf unwind: Report module before querying isactivation in dwfl unwind
fs: pass on flags in compat_writev
objtool: Add fortify_panic as __noreturn function
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
i2c: ismt: fix wrong device address when unmap the data buffer
i2c: rcar: use correct length when unmapping DMA
powerpc/xive: Fix offset for store EOI MMIOs
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a new capability CEC_CAP_NEEDS_HPD. If this capability is set
then the hardware can only use CEC if the HDMI Hotplug Detect pin
is high. Such hardware cannot handle the corner case in the CEC specification
where it is possible to transmit messages even if no hotplug signal is
present (needed for some displays that turn off the HPD when in standby,
but still have CEC enabled).
Typically hardware that needs this capability have the HPD wired to the CEC
block, often to a 'power' or 'active' pin.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A simpler variant of cec_transmit_done to be used where the HW does
just a single attempt at a transmit. So if the status indicates an
error, then the corresponding error count will always be 1 and this
function figures that out based on the status argument.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function simplifies the integration of CEC in DRM drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When calling CEC_RECEIVE do not check if the adapter is configured.
Typically CEC_RECEIVE is called after a select() and if that indicates
that there are messages in the receive queue, then you should always be
able to dequeue a message.
The race condition here is that a message has been received and is
queued, so select() tells userspace that a message is available. But
before the application calls CEC_RECEIVE the adapter is unconfigured
(e.g. the HDMI cable is removed). Now select will always report that
there is a message, but calling CEC_RECEIVE will always return -ENONET
because the adapter is no longer configured and so will never actually
dequeue the message.
There is really no need for this check, and in fact the ENONET error
code was never documented for CEC_RECEIVE. This may have been a left-over
of old code that was never updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- use __func__ instead of writing the full function name
- drop debug message in cec_config_log_addr since the same information
will be reported later
- use debug level 1 for errors and infrequent events, use level 2 for
debugging CEC message traffic
- log when a transmit is retried, very useful to know when debugging
- debug messages now all start with lower case
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=+jBV
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-2' into patchwork
media fixes for v4.12-rc4
* tag 'media/v4.12-2': (598 commits)
[media] rc-core: race condition during ir_raw_event_register()
[media] cec: drop MEDIA_CEC_DEBUG
[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER
[media] cec: select CEC_CORE instead of depend on it
[media] rainshadow-cec: ensure exit_loop is intialized
[media] atomisp: don't treat warnings as errors
Linux 4.12-rc3
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
PCI/msi: fix the pci_alloc_irq_vectors_affinity stub
blk-mq: Only register debugfs attributes for blk-mq queues
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Changing the IS_REACHABLE() into a plain #ifdef broke the case of
CONFIG_MEDIA_RC=m && CONFIG_MEDIA_CEC=y:
drivers/media/cec/cec-core.o: In function `cec_unregister_adapter':
cec-core.c:(.text.cec_unregister_adapter+0x18): undefined reference to `rc_unregister_device'
drivers/media/cec/cec-core.o: In function `cec_delete_adapter':
cec-core.c:(.text.cec_delete_adapter+0x54): undefined reference to `rc_free_device'
drivers/media/cec/cec-core.o: In function `cec_register_adapter':
cec-core.c:(.text.cec_register_adapter+0x94): undefined reference to `rc_register_device'
cec-core.c:(.text.cec_register_adapter+0xa4): undefined reference to `rc_free_device'
cec-core.c:(.text.cec_register_adapter+0x110): undefined reference to `rc_unregister_device'
drivers/media/cec/cec-core.o: In function `cec_allocate_adapter':
cec-core.c:(.text.cec_allocate_adapter+0x234): undefined reference to `rc_allocate_device'
drivers/media/cec/cec-adap.o: In function `cec_received_msg':
cec-adap.c:(.text.cec_received_msg+0x734): undefined reference to `rc_keydown'
cec-adap.c:(.text.cec_received_msg+0x768): undefined reference to `rc_keyup'
This adds an additional dependency to explicitly forbid this combination.
Fixes: 5f2c467c54 ("[media] cec: add MEDIA_CEC_RC config option")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Just depend on DEBUG_FS, no need to invent a new kernel config.
Especially since CEC can be enabled by drm without enabling
MEDIA_SUPPORT.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This config option is strictly speaking independent of the
media subsystem since it can be used by drm as well.
Besides, it looks odd when drivers select CEC_CORE and
MEDIA_CEC_NOTIFIER, that's inconsistent naming.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC framework is used by both drm and media. That makes it tricky
to get the dependencies right.
This patch moves the CEC_CORE and MEDIA_CEC_NOTIFIER config options
out of the media menu and instead drivers that want to use CEC should
select CEC_CORE and MEDIA_CEC_NOTIFIER (if needed).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Changing the IS_REACHABLE() into a plain #ifdef broke the case of
CONFIG_MEDIA_RC=m && CONFIG_MEDIA_CEC=y:
drivers/media/cec/cec-core.o: In function `cec_unregister_adapter':
cec-core.c:(.text.cec_unregister_adapter+0x18): undefined reference to `rc_unregister_device'
drivers/media/cec/cec-core.o: In function `cec_delete_adapter':
cec-core.c:(.text.cec_delete_adapter+0x54): undefined reference to `rc_free_device'
drivers/media/cec/cec-core.o: In function `cec_register_adapter':
cec-core.c:(.text.cec_register_adapter+0x94): undefined reference to `rc_register_device'
cec-core.c:(.text.cec_register_adapter+0xa4): undefined reference to `rc_free_device'
cec-core.c:(.text.cec_register_adapter+0x110): undefined reference to `rc_unregister_device'
drivers/media/cec/cec-core.o: In function `cec_allocate_adapter':
cec-core.c:(.text.cec_allocate_adapter+0x234): undefined reference to `rc_allocate_device'
drivers/media/cec/cec-adap.o: In function `cec_received_msg':
cec-adap.c:(.text.cec_received_msg+0x734): undefined reference to `rc_keydown'
cec-adap.c:(.text.cec_received_msg+0x768): undefined reference to `rc_keyup'
This adds an additional dependency to explicitly forbid this combination.
Fixes: 5f2c467c54 ("[media] cec: add MEDIA_CEC_RC config option")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=Snzj
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates for v4.12-rc1:
- new driver to support mediatek jpeg in hardware codec
- rc-lirc, s5p-cec and st-cec staging drivers got promoted
- hardware histogram support for vsp1 driver
- added Virtual Media Controller driver, to make easier to test the
media controller
- added a new CEC driver (rainshadow-cec)
- removed two staging LIRC drivers for obscure hardware that are too
obsolete
- added support for Intel SR300 Depth camera
- some improvements at CEC and RC core
- lots of driver cleanups, improvements all over the tree
With this series, we're finally getting rid of the LIRC staging
driver. There's just one left (lirc_zilog), with require more care,
as part of its functionality (IR RX) is already provided by another
driver. Work in progress to convert it on the proper way"
* tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (304 commits)
[media] ov2640: print error if devm_*_optional*() fails
[media] atmel-isc: Fix the static checker warning
[media] ov2640: add support for MEDIA_BUS_FMT_YVYU8_2X8 and MEDIA_BUS_FMT_VYUY8_2X8
[media] ov2640: fix vflip control
[media] ov2640: fix duplicate width+height returning from ov2640_select_win()
[media] ov2640: add missing write to size change preamble
[media] ov2640: add information about DSP register 0xc7
[media] ov2640: improve banding filter register definitions/documentation
[media] ov2640: fix init sequence alignment
[media] ov2640: make GPIOLIB an optional dependency
[media] xc5000: fix spelling mistake: "calibration"
[media] vidioc-queryctrl.rst: fix menu/int menu references
[media] media-entity: only call dev_dbg_obj if mdev is not NULL
[media] pixfmt-meta-vsp1-hgo.rst: remove spurious '-'
[media] mtk-vcodec: avoid warnings because of empty macros
[media] coda: bump maximum number of internal framebuffers to 17
[media] media: mtk-vcodec: remove informative log
[media] subdev-formats.rst: remove spurious '-'
[media] dw2102: limit messages to buffer size
[media] ttusb2: limit messages to buffer size
...
Add an explicit config option to select whether the CEC remote control
messages are to be passed on to the RC subsystem or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the separate cec-edid.h header and merge it into cec.h.
There was really no need to have a separate header for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Kconfig options for the CEC subsystem were a bit messy. In
addition there were two cec sources (cec-edid.c and cec-notifier.c)
that were outside of the media/cec directory, which was weird.
Move those sources to media/cec as well.
The cec-edid and cec-notifier functionality is now part of the cec
module and these are no longer separate modules.
Also remove the MEDIA_CEC_EDID config option and include it with the
main CEC config option (which defined CEC_EDID anyway).
Added static inlines to cec-edid.h for dummy functions when CEC_CORE
isn't defined.
CEC drivers should now depend on CEC_CORE.
CEC drivers that need the cec-notifier functionality must explicitly
select CEC_NOTIFIER.
The s5p-cec and stih-cec drivers depended on VIDEO_DEV instead of
CEC_CORE, fix that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is a bit confusing how CEC_CAP_RC and IS_REACHABLE(CONFIG_RC_CORE)
interact. By stripping CEC_CAP_RC at the beginning rather than after #else
it should be a bit clearer what is going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently when the RC Core is enabled (reachable) core code located
in cec_register_adapter() attempts to populate the RC structure with
a pointer to the 'parent' passed in by the caller.
Unfortunately if the caller did not specify RC capability when calling
cec_allocate_adapter(), then there will be no RC structure to populate.
This causes a "NULL pointer dereference" error.
Fixes: f51e80804f ("[media] cec: pass parent device in register(), not allocate()")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Linus Torvalds
Greg Kroah-Hartman
Hans Verkuil
Hans Verkuil
Sean Young
Mauro Carvalho Chehab
Hans Verkuil
Jose Abreu
Andrew Morton
Arnd Bergmann
Lee Jones