Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
This is for consistency with ipv4. Using "-1" makes
no sense.
It was made this way a long time ago merely to be consistent
with how the ipv6 socket hoplimit "default" is stored.
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c1f19b51d1 (net: support time stamping in phy devices.),
kernel might crash if CONFIG_NETWORK_PHY_TIMESTAMPING=y and
skb_defer_rx_timestamp() handles a packet without an ethernet header.
Fixes kernel bugzilla #24102
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=24102
Reported-and-tested-by: Andrew Watts <akwatts@ymail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_pre_routing functions in bridging have collected two
distinct ways of returning NF_DROP over the years, inline and
via goto. There is no reason for preferring either one.
So this patch arbitrarily picks the inline variant and converts
the all the gotos.
Also removes a redundant comment.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
While an interface is down, many implementations of
ethtool_ops::get_link, including the default, ethtool_op_get_link(),
will report the last link state seen while the interface was up. In
general the current physical link state is not available if the
interface is down.
Define ETHTOOL_GLINK to reflect whether the interface *and* any
physical port have a working link, and consistently return 0 when the
interface is down.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relationships
exposed by sysfs and udev. Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We know for sure pktgen is going to write skb->data right after
*_alloc_skb, causing unnecessary cache misses.
Idea is to add a prefetchw() call to prefetch the first cache line
indicated by skb->data. On systems with Adjacent Cache Line Prefetch,
it's probably two cache lines are prefetched.
With this patch, pktgen on Intel SR1625 server with two E5530
quad-core processors and a single ixgbe-based NIC went from 8.63Mpps
to 9.03Mpps, with 4.6% improvement.
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP_SET_PEER_PRIMARY_ADDR does not accpet v4mapped address, using
v4mapped address in SCTP_SET_PEER_PRIMARY_ADDR socket option will
get -EADDRNOTAVAIL error if v4map is enabled. This patch try to
fix it by mapping v4mapped address to v4 address if allowed.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TFC padding to all packets smaller than the boundary configured
on the xfrm state. If the boundary is larger than the PMTU, limit
padding to the PMTU.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TFC padding to all packets smaller than the boundary configured
on the xfrm state. If the boundary is larger than the PMTU, limit
padding to the PMTU.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XFRMA_TFCPAD attribute for XFRM state installation configures
Traffic Flow Confidentiality by padding ESP packets to a specified
length.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb1 should be passed as parameter to sk_rcvqueues_full() here.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If br_multicast_new_group returns NULL, we would return 0 (no error) to
the caller of br_multicast_add_group, which is not what we want. Instead
br_multicast_new_group should return ERR_PTR(-ENOMEM) in this case.
Also propagate the error number returned by br_mdb_rehash properly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
New idev are advertised with NL group RTNLGRP_IPV6_IFADDR, but
should use RTNLGRP_IPV6_IFINFO.
Bug was introduced by commit 8d7a76c9.
Signed-off-by: Wang Xuefu <xuefu.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove macros which have been unused since the initial implementation
(commit 7c657876b6, [DCCP]: Initial
implementation from Tue Aug 9 20:14:34 2005 -0700).
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
__load_pointer() checks data we fetch from skb is included in head
portion, but assumes we fetch one byte, instead of up to four.
This wont crash because we have extra bytes (struct skb_shared_info)
after head, but this can read uninitialized bytes.
Fix this using size of the data (1, 2, 4 bytes) in the test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_state_migrate calls kfree instead of xfrm_state_put to free
a failed state. According to git commit 553f9118 this can cause
memory leaks.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commit b178bb3dfc (net: reorder struct sock fields)
Optimize INET input path a bit further, by :
1) moving sk_refcnt close to sk_lock.
This reduces number of dirtied cache lines by one on 64bit arches (and
64 bytes cache line size).
2) moving inet_daddr & inet_rcv_saddr at the beginning of sk
(same cache line than hash / family / bound_dev_if / nulls_node)
This reduces number of accessed cache lines in lookups by one, and dont
increase size of inet and timewait socks.
inet and tw sockets now share same place-holder for these fields.
Before patch :
offsetof(struct sock, sk_refcnt) = 0x10
offsetof(struct sock, sk_lock) = 0x40
offsetof(struct sock, sk_receive_queue) = 0x60
offsetof(struct inet_sock, inet_daddr) = 0x270
offsetof(struct inet_sock, inet_rcv_saddr) = 0x274
After patch :
offsetof(struct sock, sk_refcnt) = 0x44
offsetof(struct sock, sk_lock) = 0x48
offsetof(struct sock, sk_receive_queue) = 0x68
offsetof(struct inet_sock, inet_daddr) = 0x0
offsetof(struct inet_sock, inet_rcv_saddr) = 0x4
compute_score() (udp or tcp) now use a single cache line per ignored
item, instead of two.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to hide all direct accesses, especially writes,
to dst_entry metrics values.
This will allow us to:
1) More easily change how the metrics are stored.
2) Implement COW for metrics.
In particular this will help us put metrics into the inetpeer
cache if that is what we end up doing. We can make the _metrics
member a pointer instead of an array, initially have it point
at the read-only metrics in the FIB, and then on the first set
grab an inetpeer entry and point the _metrics member there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Unconditional use of skb->dev won't work here,
try to fetch the econet device via skb_dst()->dev
instead.
Suggested by Eric Dumazet.
Reported-by: Nelson Elhage <nelhage@ksplice.com>
Tested-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure sysctl_tcp_cookie_size is read once in
tcp_cookie_size_check(), or we might return an illegal value to caller
if sysctl_tcp_cookie_size is changed by another cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: William Allen Simpson <william.allen.simpson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_tcp_tso_win_divisor might be set to zero while one cpu runs in
tcp_tso_should_defer(). Make sure we dont allow a divide by zero by
reading sysctl_tcp_tso_win_divisor exactly once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than printing the message to the log, use a mib counter to keep
track of the count of occurences of time wait bucket overflow. Reduces
spam in logs.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x25 does not decrement the network device reference counts on module unload.
Thus unregistering any pre-existing interface after unloading the x25 module
hangs and results in
unregister_netdevice: waiting for tap0 to become free. Usage count = 1
This patch decrements the reference counts of all interfaces in x25_link_free,
the way it is already done in x25_link_device_down for NETDEV_DOWN events.
Signed-off-by: Apollon Oikonomopoulos <apollon@noc.grnet.gr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the SOCK_DGRAM enum results in
"net-pf-2-proto-SOCK_DGRAM-type-115", so use the numeric value like it
is done in net/dccp.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to drop the mutex and do a dev_put, so set an error code and break like
the other paths, instead of returning directly.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is introduced in:
commit 0e3125c755
Author: Neil Horman <nhorman@tuxdriver.com>
Date: Tue Nov 16 10:26:47 2010 -0800
packet: Enhance AF_PACKET implementation to not require high order contiguous memory allocation (v4)
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some arches don't need flush_dcache_page(), and don't implement it, so
we can eliminate pgv_to_page() calls on those arches.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid some atomic ops on dst refcount, calling dev_queue_xmit_nit()
after skb_dst_drop() in dev_hard_start_xmit().
When queueing a packet into af_packet socket, we drop dst anyway.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_run_filter() doesnt write on skb, change its prototype to reflect
this.
Fix two af_packet comments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le dimanche 05 décembre 2010 à 09:19 +0100, Eric Dumazet a écrit :
> Hmm..
>
> If somebody can explain why RTNL is held in arp_ioctl() (and therefore
> in arp_req_delete()), we might first remove RTNL use in arp_ioctl() so
> that your patch can be applied.
>
> Right now it is not good, because RTNL wont be necessarly held when you
> are going to call arp_invalidate() ?
While doing this analysis, I found a refcount bug in llc, I'll send a
patch for net-2.6
Meanwhile, here is the patch for net-next-2.6
Your patch then can be applied after mine.
Thanks
[PATCH] net: RCU conversion of dev_getbyhwaddr() and arp_ioctl()
dev_getbyhwaddr() was called under RTNL.
Rename it to dev_getbyhwaddr_rcu() and change all its caller to now use
RCU locking instead of RTNL.
Change arp_ioctl() to use RCU instead of RTNL locking.
Note: this fix a dev refcount bug in llc
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le dimanche 05 décembre 2010 à 12:23 +0100, Eric Dumazet a écrit :
> Le dimanche 05 décembre 2010 à 09:19 +0100, Eric Dumazet a écrit :
>
> > Hmm..
> >
> > If somebody can explain why RTNL is held in arp_ioctl() (and therefore
> > in arp_req_delete()), we might first remove RTNL use in arp_ioctl() so
> > that your patch can be applied.
> >
> > Right now it is not good, because RTNL wont be necessarly held when you
> > are going to call arp_invalidate() ?
>
> While doing this analysis, I found a refcount bug in llc, I'll send a
> patch for net-2.6
Oh well, of course I must first fix the bug in net-2.6, and wait David
pull the fix in net-next-2.6 before sending this rcu conversion.
Note: this patch should be sent to stable teams (2.6.34 and up)
[PATCH net-2.6] llc: fix a device refcount imbalance
commit abf9d537fe (llc: add support for SO_BINDTODEVICE) added one
refcount imbalance in llc_ui_bind(), because dev_getbyhwaddr() doesnt
take a reference on device, while dev_get_by_index() does.
Fix this using RCU locking. And since an RCU conversion will be done for
2.6.38 for dev_getbyhwaddr(), put the rcu_read_lock/unlock exactly at
their final place.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org
Cc: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros already provided by kernel.h file.
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev field of ingress queue is forgot to initialized, then NULL
pointer dereference happens in qdisc_alloc().
Move inits of tx queues to netif_alloc_netdev_queues().
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug has to do with boundary checks on the initial receive window.
If the initial receive window falls between init_cwnd and the
receive window specified by the user, the initial window is incorrectly
brought down to init_cwnd. The correct behavior is to allow it to
remain unchanged.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an xprt is created, it has a refcount of 1, and XPT_BUSY is set.
The refcount is *not* owned by the thread that created the xprt
(as is clear from the fact that creators never put the reference).
Rather, it is owned by the absence of XPT_DEAD. Once XPT_DEAD is set,
(And XPT_BUSY is clear) that initial reference is dropped and the xprt
can be freed.
So when a creator clears XPT_BUSY it is dropping its only reference and
so must not touch the xprt again.
However svc_recv, after calling ->xpo_accept (and so getting an XPT_BUSY
reference on a new xprt), calls svc_xprt_recieved. This clears
XPT_BUSY and then svc_xprt_enqueue - this last without owning a reference.
This is dangerous and has been seen to leave svc_xprt_enqueue working
with an xprt containing garbage.
So we need to hold an extra counted reference over that call to
svc_xprt_received.
For safety, any time we clear XPT_BUSY and then use the xprt again, we
first get a reference, and the put it again afterwards.
Note that svc_close_all does not need this extra protection as there are
no threads running, and the final free can only be called asynchronously
from such a thread.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In order to send data to management control sockets the function should:
- skip checks intended for raw HCI data and stack internal events
- make sure RAW HCI data or stack internal events don't go to
management control sockets
In order to accomplish this the patch adds a new member to the bluetooth
skb private data to flag skb's that are destined for management control
sockets.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Wrap mesh sections inside CONFIG_MAC80211_MESH to fix compilation
problems reported by Stephen Rothwell, Larry Finger and Bruno Randolf.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/mlme.c: In function 'ieee80211_sta_work':
net/mac80211/mlme.c:1981: warning: too many arguments for format
Introduced by commit 04ac3c0ee2
("mac80211: speed up AP probing using nullfunc frames").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses pm_qos (/dev/network_latency) in order to determine the
dynamic ps timeout (or disable the dynamic-ps at all in some cases).
commit ff616381 added a comparison for the current network_latency
against one high value (1900ms), and against the default value
(2000sec, rather than the commented 2sec).
however, the representation of 1900ms was incorrect:
1900ms = 1900000us ( != 1900000000 )
fix it by using USEC_TO_MSEC/SEC consts.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that cmsg->cmsg_type value is valid for qpolicy
that is currently in use.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch adds a generic infrastructure for policy-based dequeueing of
TX packets and provides two policies:
* a simple FIFO policy (which is the default) and
* a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options).
The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Hi,
This patch fixes a typo in net/core/datagram.c and in net/sctp/socket.c
Regards,
David Shwartz
Signed-off-by: David Shwartz <dshwatrz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm going to need this in a new place later.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logically, the filter adjusting belongs with
starting/stopping mesh, not interface up/down,
so move it there.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We added some security checks in commit 57fe93b374
(filter: make sure filters dont read uninitialized memory) to close a
potential leak of kernel information to user.
This added a potential extra cost at run time, while we can perform a
check of the filter itself, to make sure a malicious user doesnt try to
abuse us.
This patch adds a check_loads() function, whole unique purpose is to
make this check, allocating a temporary array of mask. We scan the
filter and propagate a bitmask information, telling us if a load M(K) is
allowed because a previous store M(K) is guaranteed. (So that
sk_run_filter() can possibly not read unitialized memory)
Note: this can uncover application bug, denying a filter attach,
previously allowed.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: Changli Gao <xiaosuo@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only when dont_send is 0, arp_filter() is consulted, so we can simply
assign the return value of arp_filter() to dont_send instead.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we can check if an address is vmalloc address with is_vmalloc_addr(),
we remove pgv.flags. Then we may get more pg_vecs.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit causes the pgv->buffer may point to the memory
returned by vmalloc(). And we can't use virt_to_page() for the vmalloc
address.
This patch introduces a new inline function pgv_to_page(), which calls
vmalloc_to_page() for the vmalloc address, and virt_to_page() for the
__get_free_pages address.
We used to increase page pointer to get the next page at the next page
address, after Neil's patch, it is wrong, as the physical address may
be not continuous. This patch also fixes this issue.
commit 0e3125c755
Author: Neil Horman <nhorman@tuxdriver.com>
Date: Tue Nov 16 10:26:47 2010 -0800
packet: Enhance AF_PACKET implementation to not require high order contiguous memory allocation (v4)
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commits 9f0f7272 (ipv4: AF_INET link address family) and cf7afbfeb8
(rtnl: make link af-specific updates atomic) used incorrect
__in_dev_get_rcu() in RTNL protected contexts, triggering PROVE_RCU
warnings.
Switch to __in_dev_get_rtnl(), wich is more appropriate, since we hold
RTNL.
Based on a report and initial patch from Amerigo Wang.
Reported-by: Amerigo Wang <amwang@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Thomas Graf <tgraf@infradead.org>
Reviewed-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SKF_AD_RXHASH and SKF_AD_CPU to filter ancillary mechanism,
to be able to build advanced filters.
This can help spreading packets on several sockets with a fast
selection, after RPS dispatch to N cpus for example, or to catch a
percentage of flows in one queue.
tcpdump -s 500 "cpu = 1" :
[0] ld CPU
[1] jeq #1 jt 2 jf 3
[2] ret #500
[3] ret #0
# take 12.5 % of flows (average)
tcpdump -s 1000 "rxhash & 7 = 2" :
[0] ld RXHASH
[1] and #7
[2] jeq #2 jt 3 jf 4
[3] ret #1000
[4] ret #0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Rui <wirelesser@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_CSUM is a superset of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM, but
some drivers miss the difference. Fix this and also fix UFO dependency
on checksumming offload as it makes the same mistake in assumptions.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the nullfunc frame used to probe the AP was not acked, there is no point
in waiting for the probe timeout, so advance to the next try (or disconnect)
immediately.
If we do reach the probe timeout without having received a tx status, the
connection is probably really bad and worth disconnecting.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_is_nullfunc() implies ieee80211_is_data()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last_tx_rate field was also updated for non-data frames that are
often sent with a lower rate (for example management frames at 1 Mbps).
This is confusing when the data rate is actually much higher.
Hence, only update the last_tx_rate field with tx rate information
gathered from last data frames.
If the rate control algorithm filled in txrc.reported_rate we don't need
to verify this information.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to commit 63ce0900 connections initiated through TTYs created with
"rfcomm bind ..." would have security level BT_SECURITY_SDP instead of
BT_SECURITY_LOW. This would cause instant connection failure between any
two SSP capable devices due to the L2CAP connect request to RFCOMM being
sent before authentication has been performed. This patch fixes the
regression by always initializing the DLC security level to
BT_SECURITY_LOW.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If such event happens we shall reply with a Command Reject, because we are
not expecting any configure request.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pavel Emelyanov tried to fix a race between sk_filter_(de|at)tach and
sk_clone() in commit 47e958eac2
Problem is we can have several clones sharing a common sk_filter, and
these clones might want to sk_filter_attach() their own filters at the
same time, and can overwrite old_filter->rcu, corrupting RCU queues.
We can not use filter->rcu without being sure no other thread could do
the same thing.
Switch code to a more conventional ref-counting technique : Do the
atomic decrement immediately and queue one rcu call back when last
reference is released.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb head being allocated by kmalloc(), it might be larger than what
actually requested because of discrete kmem caches sizes. Before
reallocating a new skb head, check if the current one has the needed
extra size.
Do this check only if skb head is not shared.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not useful to build LED triggers when there's no LEDs that can be
triggered by them. Therefore, fix up the dependencies so that this
cannot happen, and fix a few users that select triggers to depend on
LEDS_CLASS as well (there is also one user that also selects LEDS_CLASS,
which is OK).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Arnd Hannemann <arnd@arndnet.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Moves the content of the native API routine tipc_ownidentity() into the
sole routine that calls it, since it can no longer be called in isolation.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the content of each native API message forwarding routine
into the sole routine that calls it, since the forwarding routines
no longer be called in isolation. Also removes code in each routine
that altered the outgoing message's importance level since this is
now no longer possible.
The previous function mapping (parent function, and child API) was
as follows:
tipc_send2name
\--tipc_forward2name
tipc_send2port
\--tipc_forward2port
tipc_send_buf2port
\--tipc_forward_buf2port
After this commit, the children don't exist and their functionality
is completely in the respective parent.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes a symbol that is not referenced anywhere by TIPC's link code.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes initialization of a local variable that is always assigned
a different value before it is referenced.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminates an unused argument from tipc_multicast(), now that this
routine can no longer be called by kernel-based applications.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminates support for the callback routine invoked when TIPC
changes its mode of operation from inactive to standalone or from
standalone to networked. This callback was part of TIPC's obsolete
native API and is not used by TIPC internally.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes several function declarations that aren't used anywhere,
either because they reference routines that no longer exist or
because all users of the function reference it after it has already
been defined.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifies bearer_disable() to return void since it always indicates
success anyway.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes a structure definition that is no longer used by TIPC's
configuration service.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gets rid of #include statements that are no longer required as a
result of the merging of obsolete native API header file content
into other TIPC include files.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the removal of TIPC's native API support it is no longer
necessary for TIPC to export symbols for routines that can be called
by kernel-based applications, nor for it to have header files that
kernel-based applications can include to access the declarations for
those routines. This commit eliminates the exporting of symbols by
TIPC and migrates the contents of each obsolete native API include
file into its corresponding non-native API equivalent.
The code which was migrated in this commit was migrated intact, in
that there are no technical changes combined with the relocation.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ND_REACHABLE_TIME and ND_RETRANS_TIMER have defined
since v2.6.12-rc2, but never been used.
So use them instead of magic number.
This patch also changes original code style to read comfortably .
Thank YOSHIFUJI Hideaki for pointing it out.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_BASE_MSS is defined, but not used.
commit 5d424d5a introduce this macro, so use
it to initial sysctl_tcp_base_mss.
commit 5d424d5a67
Author: John Heffner <jheffner@psc.edu>
Date: Mon Mar 20 17:53:41 2006 -0800
[TCP]: MTU probing
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will also improve handling of ipv6 tcp socket request
backlog when syncookies are not enabled. When backlog
becomes very deep, last quarter of backlog is limited to
validated destinations. Previously only ipv4 implemented
this logic, but now ipv6 does too.
Now we are only one step away from enabling timewait
recycling for ipv6, and that step is simply filling in
the implementation of tcp_v6_get_peer() and
tcp_v6_tw_get_peer().
Signed-off-by: David S. Miller <davem@davemloft.net>
The only thing AF-specific about remembering the timestamp
for a time-wait TCP socket is getting the peer.
Abstract that behind a new timewait_sock_ops vector.
Support for real IPV6 sockets is not filled in yet, but
curiously this makes timewait recycling start to work
for v4-mapped ipv6 sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use assignment in IF condition, remove extra spaces,
fixing typos, simplify code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Do not initialize static vars to zero, macros with complex values
shall be enclosed with (), remove unneeded braces.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Remove extra spaces, assignments in if statement, zeroing static
variables, extra braces. Fix includes.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Do not use assignments in IF condition, remove extra spaces
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
create_singlethread_workqueue() may fail with errors such as -ENOMEM. If
this happens, the return value is not set to a negative value and the
module load will succeed. It will then crash on module unload because of
a destroy_workqueue() call on a NULL pointer.
Additionally, the _busy_wq workqueue is not being destroyed if any
errors happen on l2cap_init().
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
rfcomm_get_sock_by_channel() was the only user of this function, so I merged
both into rfcomm_get_sock_by_channel(). The socket lock now should be hold
outside of rfcomm_get_sock_by_channel() once we hold and release it inside the
same function now.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap_get_sock_by_psm() was the only user of this function, so I merged
both into l2cap_get_sock_by_psm(). The socket lock now should be hold
outside of l2cap_get_sock_by_psm() once we hold and release it inside the
same function now.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix checkpatch errors like:
"ERROR: do not use assignment in if condition"
Simplify code and fix one long line.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In timer context we might delete l2cap channel used by krfcommd.
The check makes sure that sk is not owned. If sk is owned we
restart timer for HZ/5.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Check that socket sk is not locked in user process before removing
l2cap connection handler.
lock_sock and release_sock do not hold a normal spinlock directly but
instead hold the owner field. This means bh_lock_sock can still execute
even if the socket is "locked". More info can be found here:
http://www.linuxfoundation.org/collaborate/workgroups/networking/socketlocks
krfcommd kernel thread may be preempted with l2cap tasklet which remove
l2cap_conn structure. If krfcommd is in process of sending of RFCOMM reply
(like "RFCOMM UA" reply to "RFCOMM DISC") then kernel crash happens.
...
[ 694.175933] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 694.184936] pgd = c0004000
[ 694.187683] [00000000] *pgd=00000000
[ 694.191711] Internal error: Oops: 5 [#1] PREEMPT
[ 694.196350] last sysfs file: /sys/devices/platform/hci_h4p/firmware/hci_h4p/loading
[ 694.260375] CPU: 0 Not tainted (2.6.32.10 #1)
[ 694.265106] PC is at l2cap_sock_sendmsg+0x43c/0x73c [l2cap]
[ 694.270721] LR is at 0xd7017303
...
[ 694.525085] Backtrace:
[ 694.527587] [<bf266be0>] (l2cap_sock_sendmsg+0x0/0x73c [l2cap]) from [<c02f2cc8>] (sock_sendmsg+0xb8/0xd8)
[ 694.537292] [<c02f2c10>] (sock_sendmsg+0x0/0xd8) from [<c02f3044>] (kernel_sendmsg+0x48/0x80)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Structure hidp_conninfo is copied to userland with version, product,
vendor and name fields unitialized if both session->input and session->hid
are NULL. It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Structure cmtp_conninfo is copied to userland with some padding fields
unitialized. It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Structure bnep_conninfo is copied to userland with the field "device"
that has the last elements unitialized. It leads to leaking of
contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In Bluetooth there are no automatic updates of remote device names when
they get changed on the remote side. Instead, it is a good idea to do a
manual name request when a new connection gets created (for whatever
reason) since at this point it is very cheap (no costly baseband
connection creation needed just for the sake of the name request).
So far userspace has been responsible for this extra name request but
tighter control is needed in order not to flood Bluetooth controllers
with two many commands during connection creation. It has been shown
that some controllers simply fail to function correctly if they get too
many (almost) simultaneous commands during connection creation. The
simplest way to acheive better control of these commands is to move
their sending completely to the kernel side.
This patch inserts name requests into the sequence of events that the
kernel performs during connection creation. It does this after the
remote features have been successfully requested and before any pending
authentication requests are performed. The code will work sub-optimally
with userspace versions that still do the name requesting themselves (it
shouldn't break anything though) so it is recommended to combine this
with a userspace software version that doesn't have automated name
requests.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a single function that's responsible for requesting
authentication for outgoing connections. This is preparation for the
next patch which will add automated name requests and thereby move the
authentication requests to a different location.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The current remote and remote extended features event callbacks logic
can be made simpler by using a label and goto statements instead of the
current multiple levels of nested if statements.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
I found a problem using an IPv6 over IPv4 tunnel. When CONFIG_IPV6_SIT
was enabled, the packets would be rejected as net/ipv6/sit.c was catching
all IPPROTO_IPV6 packets and returning an ICMP port unreachable error.
I think this patch fixes the problem cleanly. I believe the code in
net/ipv4/tunnel4.c:tunnel4_rcv takes care of it properly if none of the
handlers claim the skb.
Signed-off-by: David McCullough <david_mccullough@mcafee.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ipip is built as a module the 'ip tunnel add' command would fail because
the ipip module was not being autoloaded. Adding an alias for
the tunl0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If gre is built as a module the 'ip tunnel add' command would fail because
the ip_gre module was not being autoloaded. Adding an alias for
the gre0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strcpy() rather the sprintf() for the case where name is getting
generated. Fix indentation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate qdisc memory according to NUMA properties of cpus included in
xps map.
To be effective, qdisc should be (re)setup after changes
of /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
I added a numa_node field in struct netdev_queue, containing NUMA node
if all cpus included in xps_cpus share same node, else -1.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_tunnel always assumes it consumes 40 bytes (ip6 hdr) of the mtu of the
underlaying device. So for a normal ethernet bearer, the mtu of the ip6_tunnel is
1460.
However, when creating a tunnel the encap limit option is enabled by default, and it
consumes 8 bytes more, so the true mtu shall be 1452.
I dont really know if this breaks some statement in some RFC, so this is a request for
comments.
Signed-off-by: Anders Franzen <anders.franzen@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then we can make a completely generic tcp_remember_stamp()
that uses ->get_peer() as a helper, minimizing the AF specific
code and minimizing the eventual code duplication when we implement
the ipv6 side of TW recycling.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of directly accessing "peer", change to code to
operate using a "struct inet_peer_base *" pointer.
This will facilitate the addition of a seperate tree for
ipv6 peer entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a superfluous ieee80211_is_data check as that was checked a few
lines before already and we wont't get here for non-data frames at all.
Second, the frame was already converted to 802.3 header format and
reading the fc and addr1 fields was only possible because the 802.3
header is short enough and didn't overwrite the relevant parts of the
802.11 header. Make the code more obvious by checking the ethernet
header's h_dest field.
Furthermore reorder the conditions to reduce the number of checks
when dynamic powersave is not needed (AP mode for example).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Th commit titled "mac80211: clean up rx handling wrt. found_sta"
removed found_sta variable which caused a MIC failure event
to be reported twice for a single failure to supplicant resulted
in STA disconnect.
This should fix WPA specific countermeasures WiFi test case (5.2.17)
issues with mac80211 based drivers which report MIC failure events in
rx status.
Cc: Stable <stable@kernel.org> (2.6.37)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an curious issue due to insufficient
rx frame filtering.
Saqeb Akhter reported frequent disconnects while streaming
videos over samba: <http://marc.info/?m=128600031109136>
> [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [...]
The reason is that the device generates frames with slightly
bogus SA/TA addresses.
e.g.:
[ 2314.402316] Ignore 9f:1f:31:f8:64:ff
[ 2314.402321] Ignore 9f:1f:31:f8:64:ff
[ 2352.453804] Ignore 0d:1f:31:f8:64:ff
[ 2352.453808] Ignore 0d:1f:31:f8:64:ff
^^ the group-address flag is set!
(the correct SA/TA would be: 00:1f:31:f8:64:ff)
Since the AP does not know from where the frames come, it
generates a DEAUTH response for the (invalid) mcast address.
This mcast deauth frame then passes through all filters and
tricks the stack into thinking that the AP brutally kicked
us!
This patch fixes the problem by simply ignoring
non-broadcast, group-addressed deauth/disassoc frames.
Cc: Jouni Malinen <j@w1.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Saqeb Akhter <saqeb.akhter@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX aggregation locking documentation was
wrong, which led Christian to also code the
timer timeout handling for it somewhat wrongly.
Fix the documentation, the two places that
need to hold the reorder lock across accesses
to the structure, and the debugfs code that
should just use RCU.
Also, remove acquiring the sta->lock across
reorder timeouts since it isn't necessary, and
change a few places to GFP_KERNEL because the
code path here doesn't need atomic allocations
as I noticed when reviewing all this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the new off-channel TX API
in mac80211 with a new work item type. The
operation doesn't add a new work item when
we're on the right channel and there's no
wait time so that for example p2p probe
responses will be transmitted without delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for frame injection to work properly for some use cases
(e.g., finding the station entry and keys for encryption), mac80211
needs to find the correct sdata entry. This works when the main vif
is in AP mode, but commit a2c1e3dad5
broke this particular use case for station main vif. While this type of
injection is quite unusual operation, it has some uses and we should fix
it. Do this by changing the monitor vif sdata selection to allow station
vif to be selected instead of limiting it to just AP vifs. We still need
to skip some iftypes to avoid selecting unsuitable vif for injection.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its easy to eat all kernel memory and trigger NMI watchdog, using an
exploit program that queues unix sockets on top of others.
lkml ref : http://lkml.org/lkml/2010/11/25/8
This mechanism is used in applications, one choice we have is to have a
recursion limit.
Other limits might be needed as well (if we queue other types of files),
since the passfd mechanism is currently limited by socket receive queue
sizes only.
Add a recursion_level to unix socket, allowing up to 4 levels.
Each time we send an unix socket through sendfd mechanism, we copy its
recursion level (plus one) to receiver. This recursion level is cleared
when socket receive queue is emptied.
Reported-by: Марк Коренберг <socketpair@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid sparse warnings : add __rcu annotations and use
rcu_dereference_protected() where necessary.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
store_xps_map() allocates maps that are used by single cpu, it makes
sense to use NUMA allocations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds XPS_CONFIG option to enable and disable XPS. This is
done in the same manner as RPS_CONFIG. This is also fixes build
failure in XPS code when SMP is not enabled.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet sockets corresponding to passive connections are added to the bind hash
using ___inet_inherit_port(). These sockets are later removed from the bind
hash using __inet_put_port(). These two functions are not exactly symmetrical.
__inet_put_port() decrements hashinfo->bsockets and tb->num_owners, whereas
___inet_inherit_port() does not increment them. This results in both of these
going to -ve values.
This patch fixes this by calling inet_bind_hash() from ___inet_inherit_port(),
which does the right thing.
'bsockets' and 'num_owners' were introduced by commit a9d8f9110d
(inet: Allowing more than 64k connections and heavily optimize bind(0))
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single uninitialized padding byte is leaked to userspace.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug in updating the Greatest Acknowledgment number Received (GAR):
the current implementation does not track the greatest received value -
lower values in the range AWL..AWH (RFC 4340, 7.5.1) erase higher ones.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
jhash is widely used in the kernel and because the functions
are inlined, the cost in size is significant. Also, the new jhash
functions are slightly larger than the previous ones so better un-inline.
As a preparation step, the calls to the internal macros are replaced
with the plain jhash function calls.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the vlan device is lockless and single queue do not
transfer the real num queues. This is causing a BUG_ON to occur.
kernel BUG at net/8021q/vlan.c:345!
Call Trace:
[<ffffffff813fd6e8>] ? fib_rules_event+0x28/0x1b0
[<ffffffff814ad2b5>] notifier_call_chain+0x55/0x80
[<ffffffff81089156>] raw_notifier_call_chain+0x16/0x20
[<ffffffff813e5af7>] call_netdevice_notifiers+0x37/0x70
[<ffffffff813e6756>] netdev_features_change+0x16/0x20
[<ffffffffa02995be>] ixgbe_fcoe_enable+0xae/0x100 [ixgbe]
[<ffffffffa01da06a>] vlan_dev_fcoe_enable+0x2a/0x30 [8021q]
[<ffffffffa02d08c3>] fcoe_create+0x163/0x630 [fcoe]
[<ffffffff811244d5>] ? mmap_region+0x255/0x5a0
[<ffffffff81080ef0>] param_attr_store+0x50/0x80
[<ffffffff810809b6>] module_attr_store+0x26/0x30
[<ffffffff811b9db2>] sysfs_write_file+0xf2/0x180
[<ffffffff8114fc88>] vfs_write+0xc8/0x190
[<ffffffff81150621>] sys_write+0x51/0x90
[<ffffffff8100c0b2>] system_call_fastpath+0x16/0x1b
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing struct netdev_queue state against FROZEN bit, we also test
XOFF bit. We can test both bits at once and save some cycles.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. IPV6_TLV_TEL_DST_SIZE
This has not been using for several years since created.
2. RT6_INFO_LEN
commit 33120b30 kill all RT6_INFO_LEN's references, but only this definition remained.
commit 33120b30cc
Author: Alexey Dobriyan <adobriyan@sw.ru>
Date: Tue Nov 6 05:27:11 2007 -0800
[IPV6]: Convert /proc/net/ipv6_route to seq_file interface
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_win_from_space() does the following:
if (sysctl_tcp_adv_win_scale <= 0)
return space >> (-sysctl_tcp_adv_win_scale);
else
return space - (space >> sysctl_tcp_adv_win_scale);
"space" is int.
As per C99 6.5.7 (3) shifting int for 32 or more bits is
undefined behaviour.
Indeed, if sysctl_tcp_adv_win_scale is exactly 32,
space >> 32 equals space and function returns 0.
Which means we busyloop in tcp_fixup_rcvbuf().
Restrict net.ipv4.tcp_adv_win_scale to [-31, 31].
Fix https://bugzilla.kernel.org/show_bug.cgi?id=20312
Steps to reproduce:
echo 32 >/proc/sys/net/ipv4/tcp_adv_win_scale
wget www.kernel.org
[softlockup]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The /proc/net/tcp leaks openreq sockets from other namespaces.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.
This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the if and else conditional because the code is in mainline and there
is no need in it being there.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Ensure we return the dirent->d_type when it is known
NFS: Correct the array bound calculation in nfs_readdir_add_to_array
NFS: Don't ignore errors from nfs_do_filldir()
NFS: Fix the error handling in "uncached_readdir()"
NFS: Fix a page leak in uncached_readdir()
NFS: Fix a page leak in nfs_do_filldir()
NFS: Assume eof if the server returns no readdir records
NFS: Buffer overflow in ->decode_dirent() should not be fatal
Pure nfs client performance using odirect.
SUNRPC: Fix an infinite loop in call_refresh/call_refreshresult
For drivers that have accurate TX status reporting
we can report the number of consecutive lost packets
to userspace using the new cfg80211 CQM event. The
threshold is fixed right now, this may need to be
improved in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help with latency issues which can happen when
using aggregation.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since nullfunc frames are transmitted as unicast frames, they're more
reliable than the broadcast probe requests, so we need fewer retries
to figure out whether the AP is really gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nullfunc frames are better for connection monitoring, because probe requests
are answered even if the AP has already dropped the connection, whereas
nullfunc frames from an unassociated station will trigger a disassoc/deauth
frame from the AP (WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA), which allows
the station to reconnect immediately instead of waiting until it attempts to
transmit the next unicast frame.
This only works on hardware with reliable tx ACK reporting, any other hardware
needs to fall back to the probe request method.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the connection by probing the AP (either using nullfunc or a
probe request). If nullfunc probing is supported and the assoc is no
longer valid, the AP will send a disassoc/deauth immediately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a fixed 2 second timeout, calculate beacon loss interval
from the advertised beacon interval and a frame count. With this beacon
loss happens after N (default 7) consecutive frames are missed which
for a typical setup (100TU beacon interval) is ~700ms (or ~1/3 previous).
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No change in output for pr_<level> prefixes.
netdev_<level> output is different, arguably improved.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't declare variable sized array of iovecs on the stack since this
could cause stack overflow if msg->msgiovlen is large. Instead, coalesce
the user-supplied data into a new buffer and use a single iovec for it.
Signed-off-by: Phil Blundell <philb@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing check for capable(CAP_NET_ADMIN) in SIOCSIFADDR operation.
Signed-off-by: Phil Blundell <philb@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later parts of econet_sendmsg() rely on saddr != NULL, so return early
with EINVAL if NULL was passed otherwise an oops may occur.
Signed-off-by: Phil Blundell <philb@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements transmit packet steering (XPS) for multiqueue
devices. XPS selects a transmit queue during packet transmission based
on configuration. This is done by mapping the CPU transmitting the
packet to a queue. This is the transmit side analogue to RPS-- where
RPS is selecting a CPU based on receive queue, XPS selects a queue
based on the CPU (previously there was an XPS patch from Eric
Dumazet, but that might more appropriately be called transmit completion
steering).
Each transmit queue can be associated with a number of CPUs which will
use the queue to send packets. This is configured as a CPU mask on a
per queue basis in:
/sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
The mappings are stored per device in an inverted data structure that
maps CPUs to queues. In the netdevice structure this is an array of
num_possible_cpu structures where each structure holds and array of
queue_indexes for queues which that CPU can use.
The benefits of XPS are improved locality in the per queue data
structures. Also, transmit completions are more likely to be done
nearer to the sending thread, so this should promote locality back
to the socket on free (e.g. UDP). The benefits of XPS are dependent on
cache hierarchy, application load, and other factors. XPS would
nominally be configured so that a queue would only be shared by CPUs
which are sharing a cache, the degenerative configuration woud be that
each CPU has it's own queue.
Below are some benchmark results which show the potential benfit of
this patch. The netperf test has 500 instances of netperf TCP_RR test
with 1 byte req. and resp.
bnx2x on 16 core AMD
XPS (16 queues, 1 TX queue per CPU) 1234K at 100% CPU
No XPS (16 queues) 996K at 100% CPU
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_pick_tx, don't do work in calculating queue
index or setting
the index in the sock unless the device has more than one queue. This
allows the sock to be set only with a queue index of a multi-queue
device which is desirable if device are stacked like in a tunnel.
We also allow the mapping of a socket to queue to be changed. To
maintain in order packet transmission a flag (ooo_okay) has been
added to the sk_buff structure. If a transport layer sets this flag
on a packet, the transmit queue can be changed for the socket.
Presumably, the transport would set this if there was no possbility
of creating OOO packets (for instance, there are no packets in flight
for the socket). This patch includes the modification in TCP output
for setting this flag.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lower SCM_MAX_FD from 255 to 253 so that allocations for scm_fp_list are
halved. (commit f8d570a4 added two pointers in this structure)
scm_fp_dup() should not copy whole structure (and trigger kmemcheck
warnings), but only the used part. While we are at it, only allocate
needed size.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_sk_mc_lock rwlock becomes a spinlock.
readers (inet6_mc_check()) now takes rcu_read_lock() instead of read
lock. Writers dont need to disable BH anymore.
struct ipv6_mc_socklist objects are reclaimed after one RCU grace
period.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum found a unix socket OOM was possible, posting an exploit
program.
My analysis is we can eat all LOWMEM memory before unix_gc() being
called from unix_release_sock(). Moreover, the thread blocked in
unix_gc() can consume huge amount of time to perform cleanup because of
huge working set.
One way to handle this is to have a sensible limit on unix_tot_inflight,
tested from wait_for_unix_gc() and to force a call to unix_gc() if this
limit is hit.
This solves the OOM and also reduce overall latencies, and should not
slowdown normal workloads.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
of/phylib: Use device tree properties to initialize Marvell PHYs.
phylib: Add support for Marvell 88E1149R devices.
phylib: Use common page register definition for Marvell PHYs.
qlge: Fix incorrect usage of module parameters and netdev msg level
ipv6: fix missing in6_ifa_put in addrconf
SuperH IrDA: correct Baud rate error correction
atl1c: Fix hardware type check for enabling OTP CLK
net: allow GFP_HIGHMEM in __vmalloc()
bonding: change list contact to netdev@vger.kernel.org
e1000: fix screaming IRQ
When using AP VLAN interfaces, each VLAN interface should be in its own
broadcast domain. Hostapd achieves this by assigning different GTKs to
different AP VLAN interfaces.
However, mac80211 drivers are not aware of AP VLAN interfaces and as
such mac80211 sends the GTK to the driver in the context of the base AP
mode interface. This causes problems when multiple AP VLAN interfaces
are used since the driver will use the same key slot for the different
GTKs (there's no way for the driver to distinguish the different GTKs
from different AP VLAN interfaces). Thus, only the clients associated
to one AP VLAN interface (the one that was created last) can actually
use broadcast traffic.
Fix this by not programming any GTKs for AP VLAN interfaces into the hw
but fall back to using software crypto. The GTK for the underlying AP
interface is still sent to the driver.
That means, broadcast traffic to stations associated to an AP VLAN
interface is encrypted in software whereas broadcast traffic to
stations associated to the non-VLAN AP interface is encrypted in
hardware.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.
We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.
This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.
Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.
This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:
#!/bin/bash
echo $COUNTRY >> /tmp/log
sleep 2
/sbin/crda.orig
And these regulatory tests:
modprobe mac80211_hwsim regtest=2
modprobe mac80211_hwsim regtest=3
Reported-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be required in the next patch and it makes the
next patch easier to review.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used earlier in the next few patches.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will simplify the synchronization for pending requests.
Without this we have a race between the core and when we
restore regulatory settings, although this is unlikely
its best to just avoid that race altogether.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the rpcauth_refreshcred() call returns an error other than
EACCES, ENOMEM or ETIMEDOUT, we currently end up looping forever
between call_refresh and call_refreshresult.
The correct thing to do here is to exit on all errors except
EAGAIN and ETIMEDOUT, for which case we retry 3 times, then
return EACCES.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Also, use the ccflags-$ flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched.
Last but not least, took out if-conditionals.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Also, use the ccflags-$ flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched.
Last but not least, took out if-conditionals.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ref count bug introduced by
commit 2de7957072
Author: Lorenzo Colitti <lorenzo@google.com>
Date: Wed Oct 27 18:16:49 2010 +0000
ipv6: addrconf: don't remove address state on ifdown if the address
is being kept
Fix logic so that addrconf_ifdown() decrements the inet6_ifaddr
refcnt correctly with in6_ifa_put().
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unloading pktgen module needs ~6 seconds on a 64 cpus machine, to stop
64 kthreads.
Add a pktgen_exiting variable to let kernel threads die faster, so that
kthread_stop() doesnt have to wait too long for them. This variable is
not tested in fast path.
Note : Before exiting from pktgen_thread_worker(), we must make sure
kthread_stop() is waiting for this thread to be stopped, like its done
in kernel/softirq.c
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to use __GFP_HIGHMEM in several __vmalloc() calls.
In ceph, add the missing flag.
In fib_trie.c, xfrm_hash.c and request_sock.c, using vzalloc() is
cleaner and allows using HIGHMEM pages as well.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_one_pg_vec_page() is supposed to return zeroed memory, so use
vzalloc() instead of vmalloc()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix readdir EOVERFLOW on 32-bit archs
ceph: fix frag offset for non-leftmost frags
ceph: fix dangling pointer
ceph: explicitly specify page alignment in network messages
ceph: make page alignment explicit in osd interface
ceph: fix comment, remove extraneous args
ceph: fix update of ctime from MDS
ceph: fix version check on racing inode updates
ceph: fix uid/gid on resent mds requests
ceph: fix rdcache_gen usage and invalidate
ceph: re-request max_size if cap auth changes
ceph: only let auth caps update max_size
ceph: fix open for write on clustered mds
ceph: fix bad pointer dereference in ceph_fill_trace
ceph: fix small seq message skipping
Revert "ceph: update issue_seq on cap grant"
Routing doesn't use the socket data and is protected by x25_route_list_lock
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push down the bkl in the ioctls so they can be removed one at a time.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At compile time, we can replace the DIV_K instruction (divide by a
constant value) by a reciprocal divide.
At exec time, the expensive divide is replaced by a multiply, a less
expensive operation on most processors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting the translated instruction to 1 instead of 0 allows us to
remove one descrement at check time and makes codes[] array init
cleaner.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove pc variable to avoid arithmetic to compute fentry at each filter
instruction. Jumps directly manipulate fentry pointer.
As the last instruction of filter[] is guaranteed to be a RETURN, and
all jumps are before the last instruction, we dont need to check filter
bounds (number of instructions in filter array) at each iteration, so we
remove it from sk_run_filter() params.
On x86_32 remove f_k var introduced in commit 57fe93b374
(filter: make sure filters dont read uninitialized memory)
Note : We could use a CONFIG_ARCH_HAS_{FEW|MANY}_REGISTERS in order to
avoid too many ifdefs in this code.
This helps compiler to use cpu registers to hold fentry and A
accumulator.
On x86_32, this saves 401 bytes, and more important, sk_run_filter()
runs much faster because less register pressure (One less conditional
branch per BPF instruction)
# size net/core/filter.o net/core/filter_pre.o
text data bss dec hex filename
2948 0 0 2948 b84 net/core/filter.o
3349 0 0 3349 d15 net/core/filter_pre.o
on x86_64 :
# size net/core/filter.o net/core/filter_pre.o
text data bss dec hex filename
5173 0 0 5173 1435 net/core/filter.o
5224 0 0 5224 1468 net/core/filter_pre.o
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning for sk_filter_rcu_release():
Warning(net/core/filter.c:586): missing initial short description on line:
* sk_filter_rcu_release: Release a socket filter by rcu_head
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When NF_CONNTRACK is enabled, IP_VS uses conntrack symbols.
Therefore IP_VS can't be linked statically when conntrack
is built modular.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
irttp_data_request() returns meaningful errorcodes, while irttp_udata_request()
just returns -1 in similar situations. Sync the two and the loglevels of the
accompanying output.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose reachable and retrans timer values in msecs instead of jiffies.
Both timer values are already exposed as msecs in the neighbour table
netlink interface.
The creation timestamp format with increased precision is kept but
cleaned up.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IFLA_PROTINFO exposes timer related per device settings in jiffies.
Change it to expose these values in msecs like the sysctl interface
does.
I did not find any users of IFLA_PROTINFO which rely on any of these
values and even if there are, they are likely already broken because
there is no way for them to reliably convert such a value to another
time format.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IGMP allocates MTU sized skbs. This may fail for large MTU (order-2
allocations), so add a fallback to try lower sizes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF_S_* are used internally, should not be exposed to the others.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since repeating u16 value to u8 value conversion using switch() clause's
case statement is wasteful, this patch introduces u16 to u8 mapping table
and removes most of case statements. As a result, the size of net/core/filter.o
is reduced by about 29% on x86.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to set skb priority to pktgen. Useful for testing
QOS features. Also by running pktgen on the vlan device the
qdisc on the real device can be tested.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_set_real_num_rx_queues() can decrement and increment
the number of rx queues. For example ixgbe does this as
features and offloads are toggled. Presumably this could
also happen across down/up on most devices if the available
resources changed (cpu offlined).
The kobject needs to be zero'd in this case so that the
state is not preserved across kobject_put()/kobject_init_and_add().
This resolves the following error report.
ixgbe 0000:03:00.0: eth2: NIC Link is Up 10 Gbps, Flow Control: RX/TX
kobject (ffff880324b83210): tried to init an initialized object, something is seriously wrong.
Pid: 1972, comm: lldpad Not tainted 2.6.37-rc18021qaz+ #169
Call Trace:
[<ffffffff8121c940>] kobject_init+0x3a/0x83
[<ffffffff8121cf77>] kobject_init_and_add+0x23/0x57
[<ffffffff8107b800>] ? mark_lock+0x21/0x267
[<ffffffff813c6d11>] net_rx_queue_update_kobjects+0x63/0xc6
[<ffffffff813b5e0e>] netif_set_real_num_rx_queues+0x5f/0x78
[<ffffffffa0261d49>] ixgbe_set_num_queues+0x1c6/0x1ca [ixgbe]
[<ffffffffa0262509>] ixgbe_init_interrupt_scheme+0x1e/0x79c [ixgbe]
[<ffffffffa0274596>] ixgbe_dcbnl_set_state+0x167/0x189 [ixgbe]
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes whitespace noise introduced in commit "dccp ccid-2: Algorithm to
update buffer state", 5753fdfe8b, 14 Nov 2010.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of iterating in_dev->mc_list from bonding driver, its better
to call a helper function provided by igmp.c
Details of implementation (locking) are private to igmp code.
ip_mc_rejoin_group(struct ip_mc_list *im) becomes
ip_mc_rejoin_groups(struct in_device *in_dev);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This follows wireless-testing 9236d838c9
("cfg80211: fix extension channel checks to initiate communication") and
fixes accidental case fall-through. Without this fix, HT40 is entirely
blocked.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code to handle powersaving stations has a race:
when the powersave flag is lifted from a station,
we could transmit a packet that is being processed
for TX at the same time right away, even if there
are other frames queued for it. This would cause
frame reordering. To fix this, lift the flag only
under the appropriate lock that blocks TX.
Additionally, the code to allow drivers to block a
station while frames for it are on the HW queue is
never re-enabled the station, so traffic would get
stuck indefinitely. Fix this by clearing the flag
for this appropriately.
Finally, as an optimisation, don't do anything if
the driver unblocks an already unblocked station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In many places we've just hardcoded the
AC numbers -- which is a relic from the
original mac80211 (d80211). Add constants
for them so we know what we're talking
about.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
snprintf() returns number of bytes that were copied if there is no overflow.
This code uses return value as number of copied bytes. Theoretically format
string '%lu.%09lu %pI4:%u %pI4:%u %d %#x %#x %u %u %u %u\n' may be expanded
up to 163 bytes. In reality tv.tv_sec is just few bytes instead of 20, 2 ports
are just 5 bytes each instead of 10, length is 5 bytes instead of 10. The rest
is an unstrusted input. Theoretically if tv_sec is big then copy_to_user() would
overflow tbuf.
tbuf was increased to fit in 163 bytes. snprintf() is used to follow return
value semantic.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_set_real_num_rx_queues() can decrement and increment
the number of rx queues. For example ixgbe does this as
features and offloads are toggled. Presumably this could
also happen across down/up on most devices if the available
resources changed (cpu offlined).
The kobject needs to be zero'd in this case so that the
state is not preserved across kobject_put()/kobject_init_and_add().
This resolves the following error report.
ixgbe 0000:03:00.0: eth2: NIC Link is Up 10 Gbps, Flow Control: RX/TX
kobject (ffff880324b83210): tried to init an initialized object, something is seriously wrong.
Pid: 1972, comm: lldpad Not tainted 2.6.37-rc18021qaz+ #169
Call Trace:
[<ffffffff8121c940>] kobject_init+0x3a/0x83
[<ffffffff8121cf77>] kobject_init_and_add+0x23/0x57
[<ffffffff8107b800>] ? mark_lock+0x21/0x267
[<ffffffff813c6d11>] net_rx_queue_update_kobjects+0x63/0xc6
[<ffffffff813b5e0e>] netif_set_real_num_rx_queues+0x5f/0x78
[<ffffffffa0261d49>] ixgbe_set_num_queues+0x1c6/0x1ca [ixgbe]
[<ffffffffa0262509>] ixgbe_init_interrupt_scheme+0x1e/0x79c [ixgbe]
[<ffffffffa0274596>] ixgbe_dcbnl_set_state+0x167/0x189 [ixgbe]
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_cmsg_rdma_args(), the user-provided args->nr_local value is
restricted to less than UINT_MAX. This seems to need a tighter upper
bound, since the calculation of total iov_size can overflow, resulting
in a small sock_kmalloc() allocation. This would probably just result
in walking off the heap and crashing when calling rds_rdma_pages() with
a high count value. If it somehow doesn't crash here, then memory
corruption could occur soon after.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 already exposes some address family data via netlink in the
IFLA_PROTINFO attribute if RTM_GETLINK request is sent with the
address family set to AF_INET6. We take over this format and
reuse all the code.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the AF_INET link address family exposing the per
device configuration settings via netlink using the attribute
IFLA_INET_CONF.
The format of IFLA_INET_CONF differs depending on the direction
the attribute is sent. The attribute sent by the kernel consists
of a u32 array, basically a 1:1 copy of in_device->cnf.data[].
The attribute expected by the kernel must consist of a sequence
of nested u32 attributes, each representing a change request,
e.g.
[IFLA_INET_CONF] = {
[IPV4_DEVCONF_FORWARDING] = 1,
[IPV4_DEVCONF_NOXFRM] = 0,
}
libnl userspace API documentation and example available from:
http://www.infradead.org/~tgr/libnl/doc-git/group__link__inet.html
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each net_device contains address family specific data such as
per device settings and statistics. We already expose this data
via procfs/sysfs and partially netlink.
The netlink method requires the requester to send one RTM_GETLINK
request for each address family it wishes to receive data of
and then merge this data itself.
This patch implements a new API which combines all address family
specific link data in a new netlink attribute IFLA_AF_SPEC.
IFLA_AF_SPEC contains a sequence of nested attributes, one for each
address family which in turn defines the structure of its own
attribute. Example:
[IFLA_AF_SPEC] = {
[AF_INET] = {
[IFLA_INET_CONF] = ...,
},
[AF_INET6] = {
[IFLA_INET6_FLAGS] = ...,
[IFLA_INET6_CONF] = ...,
}
}
The API also allows for address families to implement a function
which parses the IFLA_AF_SPEC attribute sent by userspace to
implement address family specific link options.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Eric Dumazet
Herbert Xu
Changli Gao
Ben Hutchings
Dan Williams
Junchang Wang
Wei Yongjun
Tobias Klauser
Martin Willi
Jiri Pirko
Nicolas Dichtel
Martin Lucina
Shan Wei
Thomas Egerer
John W. Linville
Ben Greear
Helmut Schaa
Tom Herbert
Apollon Oikonomopoulos
Michal Marek
Nelson Elhage
Thiago Farina
Nandita Dukkipati
NeilBrown
Johan Hedberg
Javier Cardona
Felix Fietkau
Eliad Peller
Bruno Randolf
Tracey Dent
Tomasz Grobelny
David Shwatrz
Johannes Berg
Michał Mirosław
Gustavo F. Padovan
Allan Stephens
Andrei Emeltchenko
Anderson Lizardo
Vasiliy Kulikov
David McCullough
stephen hemminger
Anders Franzen
Senthil Balasubramanian
Christian Lamparter
Linus Torvalds
Jouni Malinen
Nagendra Tomar
Dan Rosenberg
Gerrit Renker
Jozsef Kadlecsik
andrew hendry
John Fastabend
Uwe Kleine-König
Alexey Dobriyan
Pavel Emelyanov
Thomas Graf
Luis R. Rodriguez
Joe Perches
Phil Blundell
Trond Myklebust
Randy Dunlap
Patrick McHardy
Wolfram Sang
Tetsuo Handa
Mark Mentovai
Vasiliy Kulikov