* Tell the block layer that we are not done handling requests by using
blk_plug_device() in ide_do_request() (request handling function)
and ide_timer_expiry() (timeout handler) if the queue is not empty.
* Remove optimization which directly calls ide_do_request() for the next
queued command from the ide_intr() (IRQ handler) and ide_timer_expiry().
* Remove no longer needed IRQ masking from ide_do_request() - in case of
IDE ports needing serialization disable_irq_nosync()/enable_irq() was
used for the (possibly shared) IRQ of the other IDE port.
* Put the misplaced comment in the right place in ide_do_request().
* Drop no longer needed 'int masked_irq' argument from ide_do_request().
* Merge ide_do_request() into do_ide_request().
* Remove no longer needed IDE_NO_IRQ define.
While at it:
* Don't use HWGROUP() macro in do_ide_request().
* Use __func__ in ide_intr().
This patch reduces IRQ hadling latency for IDE and improves the system-wide
handling of shared IRQs (which should result in more timeout resistant and
stable IDE systems). It also makes it possible to do some further changes
later (i.e. replace some busy-waiting delays with sleeping equivalents).
v2:
Changes per review from Elias Oltmanns:
- fix wrong goto statement in 'if (startstop == ide_stopped)' block
- use spin_unlock_irq()
- don't use obsolete HWIF() macro
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set nIEN for previous port/device in ide_do_request()
also if port uses a non-shared IRQ.
* Remove no longer needed ide_hwif_t.sharing_irq.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix nIEN quirk check to also omit quirky devices using pdc202xx_{new,old}
host drivers for which ->quirk_list == 2.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Both choose_drive() and PM handling code make sure that the queue
is unplugged so no need to check it again.
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that (almost) all host drivers have been fixed not to abuse ide_lock
and core code usage of ide_lock has been sanitized we may safely replace
ide_lock by per-hwgroup locks.
This patch is partially based on earlier patch from Ravikiran G Thirumalai.
While at it:
- don't use deprecated HWIF() and HWGROUP() macros
- update locking documentation in ide.h
v2:
Add missing spin_lock_init(&hwgroup->lock). (Noticed by Elias Oltmanns)
Cc: Vaibhav V. Nivargi <vaibhav.nivargi@gmail.com>
Cc: Alok N. Kataria <alokk@calsoftinc.com>
Cc: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is just a preparation for future changes and there should be no
functional changes caused by this patch since ide_lock is currently
also used as queue lock.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use blk_end_request() instead of ide_lock + __blk_end_request()
in cdrom_end_request(), cdrom_newpc_intr(), __ide_end_request(),
ide_complete_pm_request() and ide_end_drive_cmd().
[ ide_lock is currently also used as queue lock ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just a preparation for future changes.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This reverts commit e9eb838830 since
it could break resume (thanks to Paul Collins for the report).
I'll look into sorting this out properly for 2.6.29
but for 2.6.28 it is the best to just revert my patch.
Reported-by: Paul Collins <paul@burly.ondioline.org>
Cc: rjw@sisk.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also while at it:
* Drop unused arguments from ide_complete_power_step().
* Move DEBUG_PM printk() from ide_end_drive_cmd() to
ide_complete_power_step().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop expected
to hit the floor). Port resets are deferred whenever a device on that
port is in the parked state.
v3:
Elias Oltmanns <eo@nebensachen.de> wrote:
[...]
> >> 1. Make sure that no negative value is being passed to
> >> jiffies_to_msecs() in ide_park_show().
> >> 2. Drop the superfluous variable hwif in ide_special_rq().
> >> 3. Skip initialisation of task and tf in ide_special_rq() if we are not
> >> handling a (un)park request.
> >
> > Well, #3 should have been done differently because we donn't want to
> > check for REQ_(UN)?PARK_HEADS more often than is necessary.
>
> While preparing the backport to 2.6.27, it has just occurred to me that
> we need to clear the IDE_DFLAG_PARKED flag in ide_disk_pre_reset()
> because this flag must not be set after *any* sort of access to the
> device.
v4:
Fix a memory leak due to a missing blk_put_request() in
issue_park_cmd(). Additionally, we should plug the queue when enqueueing
the unpark request because there is no guarantee that the park timeout
has not expired by then. Even though the chance for that to happen is
very slim, the request might end up hanging in the queue until the next
I/O operation is queued up. While at it, clean up the code a little:
- make issue_park_cmd() a function of type void since nobody cares for
the return value anyway;
- use blk_start_queueing() instead of __blk_run_queue() since we don't
have to worry about recursion;
- remove a superfluous pointer deference in task_no_data_intr().
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: Jeff Garzik <jeff@garzik.org>,
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In function ide_devset_execute() we should use __GFP_WAIT rather than
GFP_KERNEL. Also, the allocation cannot possibly fail at that point.
More importantly, there is a potential memory leak in the device probing
code. The infrastructure seems rather complex and I hope I haven't messed
anything up by trying to fix this.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
[bart: remove superfluous ide_lock taking]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ->ide_dma_clear_irq method to ->clear_irq
and move it from ide_hwif_t to struct ide_port_ops.
* Move ->waiting_for_dma check inside ->clear_irq method.
* Move ->dma_base check inside ->clear_irq method.
piix.c:
* Add ich_port_ops and remove init_hwif_ich() wrapper.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'drive->dn & 1' in ide_init_disk().
* remove [ata_]select_t.
While at it:
* Use ATA_DEVICE_OBS define in ide_port_init_devices_data().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide*_pm_* enums from ide-io.c to <linux/ide.h>.
* idedisk_pm_* -> ide_pm_*
* ide_pm_state_* -> ide_pm_*
* No need to set ide_pm_* enums to the fixed values.
* Uppercase ide_pm_* enums.
* Fix/update comments.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_LBA device flag and use it instead of ->select.b.lba.
Since ->tf_load uses ->select.all for ATA Device/Head register this
fixes HDIO_DRIVE_TASK[FILE] ioctls for CHS commands on LBA devices.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_DMA_PIO_RETRY and use it instead of
ide_drive_t.state + DMA_PIO_RETRY.
There should be no functional changes cause by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'unsigned long dev_flags' to ide_drive_t and convert bitfields
to IDE_DFLAG_* flags.
While at it:
- IDE_DFLAG_ADDRESSING -> IDE_DFLAG_LBA48
- fixup some comments
- remove needless g->flags zeroing from ide*_probe()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use a special request for serialisation purposes and get rid of the
awkward ide_spin_wait_hwgroup(). This also involves converting the
ide_devset structure so it can be shared by the /proc and the ioctl code.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
[bart: use rq->cmd[] directly]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_flush_ext_enabled() inline helper to <linux/ata.h>.
* ide_id_has_flush_cache_ext() -> ata_id_flush_ext_enabled()
The latter one also checks if the command is marked as
supported in word 83 and validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_flush_enabled() inline helper to <linux/ata.h>.
* ide_id_has_flush_cache() -> ata_id_flush_enabled()
The latter one also checks if the command is marked as
supported in word 83 and validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Include <linux/ata.h> directly in <linux/ide.h>
instead of through <linux/hdreg.h>.
* Include <linux/hdreg.h> only when needed.
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ATA_CMD_* defines instead of WIN_* ones.
While at it:
* EXABYTE_ENABLE_NEXT -> ATA_EXABYTE_ENABLE_NEST
* SETFEATURES_{EN,DIS}_WCACHE -> SETFEATURES_WC_{ON,OFF}
* SETFEATURES_{EN,DIS}_AAM -> SETFEATURES_AAM_{ON,OFF}
* SMART_* -> ATA_SMART_*
* Remove stale comment from ide-proc.c.
Partially based on earlier work by Chris Wedgwood.
Acked-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This condition is checked by both ide_disk_init_mult_count()
and set_multcount() so no need to do it again in ide_disk_special().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_tp_ops for transport methods.
* Add 'const struct ide_tp_ops *tp_ops' to struct ide_port_info
and ide_hwif_t.
* Set the default hwif->tp_ops in ide_init_port_data().
* Set host driver specific hwif->tp_ops in ide_init_port().
* Export ide_exec_command(), ide_read_status(), ide_read_altstatus(),
ide_read_sff_dma_status(), ide_set_irq(), ide_tf_{load,read}()
and ata_{in,out}put_data().
* Convert host drivers and core code to use struct ide_tp_ops.
* Remove no longer needed default_hwif_transport().
* Cleanup ide_hwif_t from methods that are now in struct ide_tp_ops.
While at it:
* Use struct ide_port_info in falconide.c and q40ide.c.
* Rename ata_{in,out}put_data() to ide_{in,out}put_data().
v2:
* Fix missing convertion in ns87415.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().
While at it:
* Use ->set_irq in init_irq() and do_reset1().
* Don't use HWIF() macro in ide_check_pm_state().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_read_status() inline helper.
* Add ->read_status method for reading ATA Status register
and use it instead of ->INB.
While at it:
* Don't use HWGROUP() macro.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove some code which has been made obsolete and hasn't worked properly
before anyway. Part of the infrastructure may be reintroduced in a
follow up patch to implement a working command aborting facility.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently, the code path executing an HDIO_DRIVE_RESET ioctl is broken
in various ways. Most importantly, it is treated as an out of band
request in an illegal way which may very likely lead to system lock ups.
Use the drive's request queue to avoid this problem (and fix a locking
issue for free along the way).
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_do_drive_cmd is called only with ide_preempt action argument. So
we can remove the action argument in ide_do_drive_cmd and ide_action_t
typedef.
This patch also includes two minor cleanups: 1) ide_do_drive_cmd
always succeeds so we don't need the return value; 2) the callers use
blk_rq_init before ide_do_drive_cmd so there is no need to initialize
rq->errors.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move IRQ unmasking out from ->tf_load method to its users.
There should be no functional changes caused by this patch
(SELECT_MASK() is NOP except for hpt366, icside and sgiioc4).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just use the new & shiny ide_pad_transfer() helper instead.
Also remove the superfluous check for 'drive->media == ide_disk'
while at it (ide_ata_error() is used only for ide_disk devices).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_init_drive_cmd just calls blk_rq_init. This converts the users of
ide_init_drive_cmd to use blk_rq_init directly and removes
ide_init_drive_cmd.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now all the users of ide_do_drive_cmd using ide_wait/head_wait are
converted to use blk_execute_rq this removes the ide_wait/head_wait
path in ide_do_drive_cmd.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Call __elv_add_request() with 'plug' == 1 (so the device will be
plugged) and then use __generic_unplug_device() instead of calling
ide_do_request() directly.
v2:
* For blk_pm_resume_request() requests the queue is stopped so we
need to call ->request_fn explicitly.
Thanks to:
- Rafael for reporting/bisecting the bug
- Borislav/Rafael for testing the fix
This is a preparation for converting IDE to use blk_execute_rq().
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set REQ_PREEMPT request flag in ide_do_drive_cmd() users
for ide_preempt and ide_head_wait action types.
* Remove setting REQ_PREEMPT from ide_do_drive_cmd().
While at it:
* Set 'where' variable outside ide_lock.
This is a preparation for converting IDE to use blk_execute_rq().
There should be no functional changes caused by this patch.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This converts ide to use blk_rq_init to initialize the request.
This is a preparation for large command support, which needs to
initialize the request in a proper way (that is, just doing a memset()
will not work).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
internally so the transfer is also padded to drive+host requirements)
and use it instead of ide_atapi_{write_zeros,discard_data}().
* Remove no longer needed ide_atapi_{write_zeros,discard_data}().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
methods in default_hwif_transport().
* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.
* Make ide_tf_{load,read}() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out debugging code from ide_tf_load() to ide_tf_dump() helper
and update ide_tf_load() users accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always use ->OUTBSYNC method for executing commands so the posting is done
if needed (this affects only pmac and scc_pata host drivers at the moment).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
into new ->{in,out}put_data methods which take number of bytes to
transfer as an argument and always do padding.
While at it:
* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.
There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods to
falconide and q40ide host drivers (->ata_* methods are implemented on
top of ->atapi_* methods so they also do byte-swapping now).
* Cleanup atapi_{in,out}put_bytes().
v2:
* Add 'struct request *rq' argument to ->ata_{in,out}put_data methods
and don't byte-swap disk fs requests (we shouldn't un-swap fs requests
because fs itself is stored byte-swapped on the disk) - this is how
things were done before the patch (ideally device mapper should be
used instead but it would break existing setups and would have some
performance impact).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_io_ports and use it instead of `unsigned long io_ports[]`
in ide_hwif_t.
* Rename io_ports[] in hw_regs_t to io_ports_array[].
* Use un-named union for 'unsigned long io_ports_array[]' and 'struct
ide_io_ports io_ports' in hw_regs_t.
* Remove IDE_*_OFFSET defines.
v2:
* scc_pata.c build fix from Stephen Rothwell.
v3:
* Fix ctl_adrr typo in Sparc-specific part of ns87415.c.
(Noticed by Andrew Morton)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add struct ide_dma_ops and convert core code + drivers to use it.
While at it:
* Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods.
* Drop "ide_" "infixes" from DMA methods.
* au1xxx-ide.c:
- use auide_dma_{test_irq,end}() directly in auide_dma_timeout()
* pdc202xx_old.c:
- drop "old_" "infixes" from DMA methods
* siimage.c:
- add siimage_dma_test_irq() helper
- print SATA warning in siimage_init_one()
* Remove no longer needed ->init_hwif implementations.
v2:
* Changes based on review from Sergei:
- s/siimage_ide_dma_test_irq/siimage_dma_test_irq/
- s/drive->hwif/hwif/ in idefloppy_pc_intr().
- fix patch description w.r.t. au1xxx-ide changes
- fix au1xxx-ide build
- fix naming for cmd64*_dma_ops
- drop "ide_" and "old_" infixes
- s/hpt3xxx_dma_ops/hpt37x_dma_ops/
- s/hpt370x_dma_ops/hpt370_dma_ops/
- use correct DMA ops for HPT302/N, HPT371/N and HPT374
- s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/
v3:
* Two bugs slipped in v2 (noticed by Sergei):
- use correct DMA ops for HPT374 (for real this time)
- handle HPT370/HPT370A properly
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move hooks for port/host specific methods from ide_hwif_t to
'struct ide_port_ops'.
* Add 'const struct ide_port_ops *port_ops' to 'struct ide_port_info'
and ide_hwif_t.
* Update host drivers and core code accordingly.
While at it:
* Rename ata66_*() cable detect functions to *_cable_detect() to match
the standard naming. (Suggested by Sergei Shtylyov)
v2:
* Fix build for bast-ide. (Noticed by Andrew Morton)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check for IDE_HFLAG_NO_SET_MODE host flag in ide_set_pio(),
ide_set_[pio,dma]_mode(), ide_set_xfer_rate() and set_pio_mode().
* Remove no longer needed IDE_HFLAG_NO_SET_MODE host flag checking
from ide_tune_dma().
* Remove superfluous ->set_pio_mode checking from do_special().
This is a part of preparations for adding 'struct ide_port_ops'.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_{ALTSTATUS,IREASON,BCOUNTL,BCOUNTH}_OFFSET defines.
* Remove IDE_*_REG macros - this results in more readable
and slightly smaller code.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 813a0eb233
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Fri Jan 25 22:17:10 2008 +0100
ide: switch idedisk_prepare_flush() to use REQ_TYPE_ATA_TASKFILE requests
...
broke flush requests.
Allocating IDE command structure on the stack for flush requests is not
a very brilliant idea:
- idedisk_prepare_flush() only prepares the request and it doesn't wait
for it to be completed
- there are can be multiple flush requests queued in the queue
Fix the problem (per hints from James Bottomley) by:
- dynamically allocating ide_task_t instance using kmalloc(..., GFP_ATOMIC)
- adding new taskfile flag (IDE_TFLAG_DYN)
- calling kfree() in ide_end_drive_command() if IDE_TFLAG_DYN is set
(while at it rename 'args' to 'task' and fix whitespace damage)
[ This will be fixed properly before 2.6.25 but this bug is rather
critical and the proper solution requires some more work + testing. ]
Thanks to Sebastian Siewior and Christoph Hellwig for reporting the
problem and testing patches (extra thanks to Sebastian for bisecting
it to the guilty commmit).
Tested-by: Sebastian Siewior <ide-bug@ml.breakpoint.cc>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I have reviewed all blk-end-request patches again to confirm whether
there are any similar problems with the last week's ide-cd panic:
http://lkml.org/lkml/2008/1/29/140
And I found a possible similar bug in ide-io change:
ide_end_drive_cmd() could be called for blk_pc_request() which could
have bios. To complete such requests correctly, we need to pass
the actual size of the request.
Otherwise, __blk_end_request() returns 1 because the request still has
bios, and the system will BUG() unnecessarily.
The following patch fixes the bug and should be applied on top of
Linus' git.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch converts "normal" parts of ide to use blk_end_request
interfaces. Related 'uptodate' arguments are converted to 'error'.
The conversion of 'uptodate' to 'error' is done only for the internal
function, __ide_end_request().
ide_end_request() was not changed since it's exported and used
by many ide drivers.
With this patch, blkdev_dequeue_request() in __ide_end_request() is
moved to blk_end_request, since blk_end_request takes care of
dequeueing request like below:
if (!list_empty(&rq->queuelist))
blkdev_dequeue_request(rq);
In the case of ide,
o 'dequeue' variable of __ide_end_request() is 1 only when the request
is still linked to the queue (i.e. rq->queuelist is not empty)
o 'dequeue' variable of __ide_end_request() is 0 only when the request
has already been removed from the queue (i.e. rq->queuelist is empty)
So blk_end_request can handle it correctly although ide always run
thought the code above.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't check for READY_STAT bit being set for PIO-in protocol (makes the
final status check in drive_cmd_intr() match the one in task_in_intr()).
Also fix function name reported by ide_error() call while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't enable local IRQs for PIO-in protocol in driver_cmd_intr().
While at it:
* Remove redundant rq->cmd_type check.
* Read status register after enabling local IRQs for no-data protocol.
v2:
* Re-add DRQ=1 check lost in v1 (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use wait_drive_not_busy() in drive_cmd_intr().
v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.
* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.
* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dump_status() may set HOB bit before ide_end_drive_cmd() is called.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->dma_off_quietly is always called before ide_set_dma()
so the call can be moved inside ide_set_dma().
* ide_dma_check() doesn't touch hardware so ->dma_off_quietly
call for 'rc == -1' case is redundant, remove it.
* '0' and '-1' are the only values returned by ide_dma_check()
so remove dead code for other cases.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out code reading taskfile registers from ide_end_drive_cmd()
to the new ide_tf_read() helper.
* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
particular IDE taskfile register in ide_tf_read().
* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.
* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.
* Factor out code getting sector address from ide_dump_ata_status()
to the new ide_dump_sector() function.
* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().
* Remove no longer needed ide_read_24().
The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_CUSTOM_HANDLER taskfile flag and use it for internal requests
which require custom handlers. Check the flag in do_rw_taskfile() and set
handler accordingly.
* Cleanup ide_init_{specify,restore,setmult}_cmd() and rename it to
ide_tf_set_{specify,restore,setmult}_cmd().
* Make {set_geometry,recal,set_multmode}_intr() static.
* Remove no longer needed 'handler' field from ide_task_t.
v2:
* 'handler' in do_rw_taskfile() must be set to NULL initially.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->data_phase to set ->handler in do_rw_taskfile() instead of
setting ->handler in callers of ide_raw_taskfile()/do_rw_taskfile().
* Unexport task_no_data_intr() and make it static.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
task->data_phase == TASKFILE_MULTI_{IN,OUT} vs drive->mult_count == 0
check is needed also for ide_taskfile_ioctl() requests that don't have
IDE_TFLAG_FLAGGED taskfile flag set.
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_IN_DATA taskfile flag to indicate the need of reading
IDE_DATA_REG in ide_end_drive_cmd().
Set the new flag in ide_taskfile_ioctl() if ->in_flags.b.data is set.
* Add IDE_TFLAG_FLAGGED_SET_IN_FLAGS taskfile flag to indicate the
need of modifying ->in_flags in ide_taskfile_ioctl().
Set the new flag in flagged_taskfile() and move the code modifying
->tf_in_flags to ide_taskfile_ioctl().
While at it remove the bogus comment: ->tf_in_flags (except .b.data)
have no effect on selection of registers to read.
* Remove no longer needed 'tf_in_flags' field from ide_task_t.
As the result we finally have the internals of HDIO_DRIVE_TASKFILE ioctl
separated from the core IDE code.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'data_buf' and 'nsect' variables in ide_taskfile_ioctl()
to cache data buffer pointer and number of sectors to transfer
(this allows us to have only one ide_diag_taskfile() call).
* Add IDE_TFLAG_WRITE taskfile flag and use it to check whether
the REQ_RW request flag should be set.
* Move ->command_type handling from ide_diag_taskfile() to
ide_taskfile_ioctl() and use ->req_cmd instead of ->command_type.
* Add 'nsect' parameter to ide_raw_taskfile().
* Merge ide_diag_taskfile() into ide_raw_taskfile().
* Initialize ->data_phase explicitly in idedisk_prepare_flush(),
ide_start_power_step() and ide_disk_special().
* Remove no longer needed 'command_type' field from ide_task_t.
* Add #ifndef/#endif __KERNEL__ to <linux/hdreg.h> around no
longer used by kernel IDE_DRIVE_TASK_* and TASKFILE_* defines.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Given that:
* hpt366.c::hpt3xx_intrproc() is the only user of hwif->intrproc
* hpt366.c::hpt3xx_quirkproc() sets drive->quirk_list to 1 for quirky drives
which is a value unique to hpt366 host driver
we can remove hwif->intproc and just check for drive->quirk_list == 1
in ide_do_request().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_pktcmd_tf_load() helper and convert ATAPI device drivers to use it.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Extend timeout for REQ_TYPE_ATA_{CMD,TASK} requests from WAIT_CMD (10sec)
to WAIT_WORSTCASE (30sec, already used for REQ_TYPE_ATA_TASKFILE).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set taskfile flags for REQ_TYPE_ATA_TASKFILE requests before
adding the request to the queue.
* Cleanup execute_drive_cmd().
* Remove unnecessary writes to HOB taskfile registers when using
LBA48 disk for the following cases:
- Power Management requests
(WIN_FLUSH_CACHE[_EXT], WIN_STANDBYNOW1, WIN_IDLEIMMEDIATE commands)
- special commands (WIN_SPECIFY, WIN_RESTORE, WIN_SETMULT)
- Host Protected Area support (WIN_READ_NATIVE_MAX, WIN_SET_MAX)
- /proc/ide/ SMART support (WIN_SMART with SMART_ENABLE,
SMART_READ_VALUES and SMART_READ_THRESHOLDS subcommands)
- write cache enabling/disabling in ide-disk
(WIN_SETFEATURES with SETFEATURES_{EN,DIS}_WCACHE)
- write cache flushing in ide-disk (WIN_FLUSH_CACHE[_EXT])
- acoustic management in ide-disk
(WIN_SETFEATURES with SETFEATURES_{EN,DIS}_AAM)
- door (un)locking in ide-disk (WIN_DOORLOCK, WIN_DOORUNLOCK)
- /proc/ide/hd?/identify support (WIN_IDENTIFY)
- ACPI _GTF taskfiles
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use IDE_TFLAG_LBA48 for REQ_TYPE_ATA_TASKFILE requests in ide_end_drive_cmd()
to decide whether we need to read HOB taskfile registers.
* Update execute_drive_cmd() accordingly.
This is a preparation for the next patch which removes unnecessary writes to
HOB taskfile registers for some ATA commands.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_OUT_DEVICE taskfile flag to indicate the need of writing
the Device register and handle it in ide_tf_load().
Update ide_tf_load() and {do_rw,flagged}_taskfile() users accordingly.
* Use struct ide_taskfile and ide_tf_load() in execute_drive_cmd().
* Make the debugging code dump all taskfile registers for both
REQ_ATA_TYPE_{CMD,TASK} requests and move it to ide_tf_load()
so it also covers REQ_ATA_TYPE_TASKFILE requests.
There should be no functionality changes caused by this patch
(unless DEBUG is defined).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename 'args' variable in 'if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE)'
block to 'task'.
* execute_drive_cmd() is used only for REQ_TYPE_ATA_{CMD,TASK,TASKFILE} so
we can move the common code out from 'if (rq->cmd_type == REQ_TYPE_ATA_CMD)'
and 'if (rq->cmd_type == REQ_TYPE_ATA_TASK)' blocks.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move loading of IDE_NSECTOR_REG from ide_cmd() to execute_drive_cmd()
(load the IDE_NSECTOR_REG just after IDE_FEATURE_REG).
This also allows us to drop 'nsect' argument from ide_cmd() and simplify
execute_drive_cmd() code for REQ_TYPE_ATA_CMD case a bit.
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix registers loading order for REQ_TYPE_ATA_CMD request with WIN_SMART
command in execute_drive_cmd() (load IDE_FEATURE_REG and IDE_SECTOR_REG
before loading IDE_LCYL_REG and IDE_HCYL_REG).
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove stale ide.h "configuration options":
* INITIAL_MULT_COUNT - always defined to 0
* SUPPORT_SLOW_DATA_PORTS - unused
* OK_TO_RESET_CONTROLLER - always defined to 1
* DISABLE_IRQ_NOSYNC - always defined to 0
Leave SUPPORT_VLB_SYNC (defined to 0 for CRIS and FRV, otherwise to 1)
for now but disallow overriding it by <asm/ide.h>.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
* Move setting IDE_TFLAG_LBA48 taskfile flag from do_rw_taskfile()
function to the callers.
* Add IDE_TFLAG_FLAGGED taskfile flag for flagged taskfiles coming
from ide_taskfile_ioctl(). Check it instead of ->tf_out_flags.all.
* Add IDE_TFLAG_OUT_DATA taskfile flag to indicate the need to load
IDE data register in ide_tf_load().
* Add IDE_TFLAG_OUT_* taskfile flags to indicate the need to load
particular IDE taskfile registers in ide_tf_load().
* Update do_rw_taskfile() and ide_tf_load() users to set respective
IDE_TFLAG_OUT_* taksfile flags.
* Add task_dma_ok() helper.
* Use IDE_TFLAG_FLAGGED taskfile flag to select HIHI mask in ide_tf_load().
* Use do_rw_taskfile() in flagged_taskfile().
* Remove no longer needed 'tf_out_flags' field from ide_task_t.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't set write-only ide_task_t.hobRegister[6] and ide_task_t.hobRegister[7]
in idedisk_set_max_address_ext().
* Add struct ide_taskfile and use it in ide_task_t instead of tfRegister[]
and hobRegister[].
* Remove no longer needed IDE_CONTROL_OFFSET_HOB define.
* Add #ifndef/#endif __KERNEL__ around definitions of {task,hob}_struct_t.
While at it:
* Use ATA_LBA define for LBA bit (0x40) as suggested by Tejun Heo.
v2:
* Add missing newlines. (Noticed by Sergei)
* Use ~ATA_LBA instead of 0xBF. (Noticed by Sergei)
* Use unnamed unions for error/feature and status/command.
(Suggested by Sergei).
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently it's possible to ide-cd to set an incorrect blocksize by
reading garbage if the drive is dead:
ide_cd_probe()
-> cdrom_read_toc()
-> cdrom_read_capacity()
-> cdrom_queue_packet_command()
-> ide_do_drive_cmd()
-> ide_do_request()
-> start_request()
on start_request():
/* bail early if we've exceeded max_failures */
if (drive->max_failures && (drive->failures > drive->max_failures)) {
goto kill_rq;
}
(...)
kill_rq:
ide_kill_rq(drive, rq);
return ide_stopped;
ide_kill_rq() and the next calls won't set REQ_FAILED on rq->cmd_flags and thus
cdrom_queue_packet_command() won't return an error. then:
stat = cdrom_queue_packet_command(drive, &req);
if (stat == 0) {
*capacity = 1 + be32_to_cpu(capbuf.lba);
*sectors_per_frame =
be32_to_cpu(capbuf.blocklen) >> SECTOR_BITS;
}
cdrom_read_capacity() ends believing capbuf is valid but in fact it's just
uninitialized data. back to cdrom_read_toc():
/* Try to get the total cdrom capacity and sector size. */
stat = cdrom_read_capacity(drive, &toc->capacity, §ors_per_frame,
sense);
if (stat)
toc->capacity = 0x1fffff;
set_capacity(info->disk, toc->capacity * sectors_per_frame);
/* Save a private copy of te TOC capacity for error handling */
drive->probed_capacity = toc->capacity * sectors_per_frame;
blk_queue_hardsect_size(drive->queue,
sectors_per_frame << SECTOR_BITS);
that will set drive->queue->hardsect_size to be the random value.
hardsect_size is used to calculate inode->i_blkbits. later on, on a read
path:
void create_empty_buffers(struct page *page,
unsigned long blocksize, unsigned long b_state)
{
struct buffer_head *bh, *head, *tail;
head = alloc_page_buffers(page, blocksize, 1);
bh = head;
do {
bh->b_state |= b_state;
tail = bh;
bh = bh->b_this_page;
} while (bh);
tail->b_this_page = head;
alloc_page_buffers() will return NULL if blocksize > 4096. blocksize is
calculed based on inode->i_blkbits. that will trigger a null
dereference on create_empty_buffers().
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add missing checks for control register existence (some legacy m68k specific
IDE controllers don't have it). Also use drive->ctl while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use drive->select.all for REQ_TYPE_ATA_TASK requests in execute_drive_cmd()
(the obsolete bits 7 and 5 of the Device register need to be set).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drive_cmd_intr() is used by both REQ_TYPE_ATA_CMD and REQ_TYPE_ATA_TASK
but commands using PIO-in protocol are valid only for REQ_TYPE_ATA_CMD
(&args[4] in case of REQ_TYPE_ATA_TASK points to a value for IDE_LCYL_REG
register instead of the data buffer). This fix allows REQ_TYPE_ATA_TASK
commands to use non-zero values for IDE_SECTOR_REG (args[3]).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove dead code for handling IDE TCQ from ide_end_dequeued_request().
* Add 'dequeue' parameter to __ide_end_request().
* Use __ide_end_request() in ide_end_dequeued_request().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Take ide_lock for prefetch disable/enable in do_special(),
then cleanup cmd640 and ht6560b host drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead
of hwif->err_stops_fifo. As a side-effect this change fixes
hwif->err_stops_fifo not being restored by ide_hwif_restore().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also ide-iops.c::__ide_wait_stat() could be static again.
Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:
* if PIO mode is set then ->dma_off_queitly is called to disable DMA
* if setting transfer mode fails ide_dump_status() is called to dump status
v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
depends on this fact, and calls "hdparm -p" without calling "hdparm -d".
Therefore to compensate for DMA being disabled by ide_config_drive_speed()
for PIO modes:
- add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver
- add handling of the new flag to ide-io.c::do_special()
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Do the same thing as probe_hwif() and always disable DMA so chipset DMA
enabled bit gets cleared (if the drive doesn't support DMA ide_set_dma()
won't try to tune it anyway).
* Add TODO comment about respecting ->using_dma setting.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-disk calls
ide_end_request(drive, 0, 0);
to finish an unknown request, but this doesn't work so well for non-fs
requests, since ide_end_request() internally looks at ->hard_cur_sectors
to see how much data to end. Only file system requests store a transfer
value in there, pc requests fill out ->data_len as a byte based transfer
value instead.
Since we ask to end 0 bytes of that request, it will never be terminated
and ide-disk gets stuck in a loop "handling" that same request over and
over.
Switch __ide_end_request() to take a byte based transfer count, and
adjust ide_end_request() to look at the right field to determine how
much IO to end when it's being passed in 0.
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-By: Giacomo Catenazzi <cate@debian.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:
- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;
- in au1xxx-ide.c, get rid of commented out printk();
- in sl82c105.c, get rid of unnecessary variables.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:
- in aec62xx.c, rename the method in accordance with other drivers, and get rid
of unnecessary variables there;
- in pdc202xx_old.c, define/use 'hwif' variable;
- in sgiioc4.c, rearrange the code to call the resetproc() method directly.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted). Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
hwif->ide_dma_clear_irq for Intel ICHx controllers.
Revised per Alan, Sergei and Bart's advice.
Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Add a step to the IDE PM state machine that reprograms disk PIO timings
as the first step on resume. This prevents ide deadlock on
resume-from-ram on my nforce3-based laptop.
An earlier implementation was written entirely within the amd74xx ide
driver, but Alan helpfully pointed out that this is the correct thing to
do globally. Still, I'm only calling hwif->tuneproc() for disks, based
on two things:
- The existing state machine is already passed over for non-disk drives
- Previous testing on my laptop shows that the hangs are related only
to the disk - suspend/resume from a livecd showed that there's no
need for this on the cdrom.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brad Campbell <brad@wasp.net.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.15.1 I encountered some IDE crashes when unplugging IDE cables to
emulate disk errors. Below is a patch against 2.6.16 which I think still
applies.
1. The first BUG_ON could trigger when a PREFLUSH IO fails (it would
fail the original barrier request which hasn't been marked REQ_STARTED
yet).
2. the rq could have been dequeued already (same as 1).
3. HWGROUP(drive)->rq could be NULL because of the ide_error() several
lines earlier.
Signed-off-by: Hua Zhong <hzhong@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After Christophs SCSI change, the only usage left is RQ_ACTIVE
and RQ_INACTIVE. The block layer sets RQ_INACTIVE right before freeing
the request, so any check for RQ_INACTIVE in a driver is a bug and
indicates use-after-free.
So kill/clean the remaining users, straight forward.
Signed-off-by: Jens Axboe <axboe@suse.de>
As the comments indicates in blkdev.h, we can fold it into ->end_io_data
usage as that is really what ->waiting is. Fixup the users of
blk_end_sync_rq().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
lockdep needs to have the waitqueue lock initialized for on-stack waitqueues
implicitly initialized by DECLARE_COMPLETION(). Annotate on-stack completions
accordingly.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make use of local_irq_enable_in_hardirq() API to annotate places that enable
hardirqs in hardirq context.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the controller FIFO cleared automatically on error we must not try
and drain it as this will hang some chips.
Based in concept on a broken patch from -mm some while back
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
During an STR resume cycle, the ide master disk times-out when there is
also a slave present (especially CD). Increasing the timeout in ide-io
from 10,000 to 100,000 fixes this problem.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch from Alan that fixes a real ide-cd.c regression causing
bogus "Media Check" failures for perfectly valid Fedora install ISOs, on
certain CD-ROM drives.
This is a forward port to 2.6.16 (from RHEL) of the minimal changes for the
end of media problem. It may not be sufficient for some controllers
(promise notably) and it does not touch the locking so the error path
locking is as horked as in mainstream.
From: Ingo Molnar <mingo@elte.hu>
I have ported the patch to 2.6.17-rc4 and tested it by provoking
end-of-media IO errors with an unaligned ISO image. Unlike the vanilla
kernel, the patched kernel interpreted the error condition correctly with
512 byte granularity:
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 04 fb 78 00 00 06 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 1306080
Buffer I/O error on device hdc, logical block 163260
Buffer I/O error on device hdc, logical block 163261
Buffer I/O error on device hdc, logical block 163262
the unpatched kernel produces an incorrect error dump:
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306080
Buffer I/O error on device hdc, logical block 163260
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306088
Buffer I/O error on device hdc, logical block 163261
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306096
Buffer I/O error on device hdc, logical block 163262
I do not have the right type of CD-ROM drive to reproduce the end-of-media
data corruption bug myself, but this same patch in RHEL solved it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Jens Axboe <axboe@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since there's no longer any external user, we can make __ide_end_request()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a problem with the REQ_BLOCK_PC handling as well (bad ->data_len
handling) where it could actually complete a request ahead of time. I
suggest we just back this out for now, I will resubmit it later when I'm
fully confident in it.
This reverts commit 8672d57138
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To preserve the ->errors values for requests that failed, use the normal
completion path for that.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes IDE use the new blk_complete_request() interface.
There's still room for improvement, as __ide_end_request() really
could drop the lock after getting HWGROUP->rq (why does it need to
hold it in the first place? If ->rq access isn't serialized, we are
screwed anyways).
Signed-off-by: Jens Axboe <axboe@suse.de>
Update IDE to use new blk_ordered. This change makes the
following behavior changes.
* Partial completion of the barrier request is handled as
failure of the whole ordered sequence. No more partial
completion for barrier requests.
* Any failure of pre or post flush request results in failure
of the whole ordered sequence.
So, successfully completed ordered sequence guarantees that
all requests prior to the barrier made to physical medium and,
then, the while barrier request made to the physical medium.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
add @uptodate argument to end_that_request_last() and @error
to rq_end_io_fn(). there's no generic way to pass error code
to request completion function, making generic error handling
of non-fs request difficult (rq->errors is driver-specific and
each driver uses it differently). this patch adds @uptodate
to end_that_request_last() and @error to rq_end_io_fn().
for fs requests, this doesn't really matter, so just using the
same uptodate argument used in the last call to
end_that_request_first() should suffice. imho, this can also
help the generic command-carrying request jens is working on.
Signed-off-by: tejun heo <htejun@gmail.com>
Signed-Off-By: Jens Axboe <axboe@suse.de>
The logic in ide_do_request() doesn't guarantee that both drives will be
serviced after a call. It may "forget" to service one in some
circumstances, including when one of the drive is suspended (it will
eventually fail to service the slave when the master is suspended for
example). This prevents the wakeup requests that gets queued on wakeup
from sleep from beeing serviced in some cases when 2 drives are sharing
an IDE bus.
The problem is deep enough in the way this code works (and there are
probably a few other problematic but rare corner cases) and fixing it
would require some major rethinking of the way IDE decides which channel
to service. This is not 2.6.14 material. However, in the meantime,
Bart has accepted this simple workaround that will fix the crash on
wakeup from sleep since this specific corner case is actually hitting
users to get into 2.6.14.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the most trivial from Rusty's trivial patches:
- spelling fixes
- remove duplicate includes
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bartlomiej Zolnierkiewicz
Michael Schmitz
Jens Axboe
Elias Oltmanns
FUJITA Tomonori
Kiyoshi Ueda
Aristeu Rozanski
Jiri Slaby
Adrian Bunk
Sergei Shtylyov
Suleiman Souhlal
Albert Lee
David Howells
Jason Lunz
Hua Zhong
Jens Axboe
Jens Axboe
Ingo Molnar
Jörn Engel
Alan Cox
Linus Torvalds
Al Boldi
Andreas Mohr
Adrian Bunk
Tejun Heo
Benjamin Herrenschmidt