Move the common code for reading and writing phy registers into the
shared mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions could in future be used by other drivers. Move them
into the shared area.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell switches are all reset in nearly the same way. The only
difference is if the PPU should be enabled or not. Move this
code into the shared mv88x6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the switch id and save it away in the private mv88x6xxx structure
in a centralised piece of code, rather than each driver doing it itself.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No vlan support at this time.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge support is similar for all chips supported by the mv88e6xxx code,
so add the code there.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split mv88e6xxx_reg_read and mv88e6xxx_reg_write into two functions each,
one to acquire smi_mutex and one to get struct mii_bus *bus from
struct dsa_switch *ds and to call the actual read/write function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datasheet says that the Message Port bit should not be set for the CPU port.
Having it set causes DSA tagged packets to be sent to the CPU port roughly
every 30 seconds. Those packets are the same as real packets forwarded between
switch ports if the switch is configured for switching between multiple ports.
The packets are then bridged by the software bridge, resulting in duplicated
packets on the network.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide mv88e6xxx_setup_port_common() for common port initialization.
Currently only write Port 1 Control and VLAN configuration since
this will be needed for hardware bridging. More can be added later
if desired/needed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code used and needed in mv886xxx.c should be initialized there as well,
so factor it out from the individual initialization files.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE configuration is similar for the various MV88E6xxx chips.
Add generic support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds debug messages for the generic mv88e6xxx read and write
routines. The output is similar to this:
mdio-gpio mdio-gpio.0: <- addr: 0x1b reg: 0x05 val: 0x4000
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x07 val: 0x3113
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x08 val: 0x0330
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x09 val: 0x0000
This is convenient to dynamically debug operations through debugfs with:
echo file mv88e6xxx.c +p > <debugfs>/dynamic_debug/control
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method to read the temperature used in the mve6123_61_65 driver
can also be used for other chips. Move the code into the shared code
base of mv88e6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display sw_in_discards, sw_in_filtered, and sw_out_filtered for chips
supported by mv88e6123_61_65 and mv88e6352 drivers.
The variables are provided in port registers, not the normal status registers.
Mark by adding 0x100 to the register offset and add special handling code
to mv88e6xxx_get_ethtool_stats.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6123_61_65 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD 406783067 PUD 406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<ffffffff81781de3>] mutex_lock+0x23/0x37
[<ffffffff81533244>] mdiobus_read+0x34/0x60
[<ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0
Fixes: b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Marvell driver with some cleanups by Claudio Leite
and myself.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Claudio Leite <leitec@staticky.com>
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the helper function to retrieve the driver private context instead of
using (void *)(ds + 1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix DSA whitespace issues reported by checkpatch.pl
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DSA printk calls to netdev_info calls as recommended by
checkpatch.pl.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DSA msleep calls to timeout/usleep_range calls
as reported by checkpatch.pl.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DSA driver comments to network-style comments as reported by
checkpatch.pl. Fix spelling error.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An implicit instance of module.h leaked back into existence
and was masking the fact that these drivers weren't calling
out the include for itself. Fix the drivers before we remove
the implicit include path via net/netprio_cgroup.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for specific hardware belongs under drivers/net/ not net/.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn
Guenter Roeck
Vivien Didelot
Alexander Duyck
Florian Fainelli
Barry Grussling
Paul Gortmaker
Ben Hutchings