Fixes for the DMA transfer mode of the driver to try and improve the state
of the code:
- Ensure that dma_complete is set during the end of the command phase
so that transfers do not stall awaiting the completion
- Update the DMA debugging to provide a bit more useful information
such as how many DMA descriptors where not processed and print the
DMA addresses in hexadecimal.
- Fix the DMA channel request code to actually request DMA for the
S3CMCI block instead of whatever '0' signified.
- Add fallback to PIO if we cannot get the DMA channel, as many of the
devices with this block only have a limited number of DMA channels.
- Only try and claim and free the DMA channel if we are trying to use it.
This improves the driver DMA code to the point where it can now identify a
card and read the partition table. However the DMA can still stall when
trying to move data between the host and memory.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The controller supports SDIO IRQ detection so add support for hardware
assisted SDIO interrupt detection for the SDIO core. This improves the
response time for SDIO interrupts and thus the transfer rate from devices
such as the Marvel 8686.
As a note, it does seem that the controller will miss an IRQ than is held
asserted, so there are some manual checks to see if the SDIO interrupt is
active after a transfer.
Major testing on the S3C2440.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export driver state and hardware register state via debugfs entries
created under a directory formed from dev_name() on the probed device when
CONFIG_DEBUG_FS is set.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To be able to do SDIO the s3cmci driver has to support non-word-sized
transfers. Change pio_words into pio_bytes and fix up all the places
where it is used.
This variant of the patch will not overrun the buffer when reading an
odd number of bytes. When writing, this variant will still read past
the end of the buffer, but since the driver can't support non-word-
aligned transfers anyway, this should not be a problem, since a
word-aligned transfer will never cross a page boundary.
This has been tested with a CSR SDIO Bluetooth Type A device on a
Samsung S3C24A0 processor.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds platform data support to the s3mci driver. This allows
flexible board-specific configuration of set_power, card detect and read only
pins.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This is the latest S3C MMC/SD driver by Thomas Kleffel
with cleanups as suggested by AKPM done by Ben Dooks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ben Dooks
Christer Weinigel
ben@fluff.org.uk
Ben Dooks
Thomas Kleffel