For a sake of code simplification, remove the init and the exit
entries that do nothing.
Notes for readers: actually it's OK to remove *both* init and exit,
but not OK to remove the exit entry. By removing only the exit while
keeping init, the module becomes permanently loaded; i.e. you cannot
unload it any longer!
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the code like the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many drivers bind the sequencer stuff in off-load by another driver
module, so that it's loaded only on demand. In the current code, this
mechanism doesn't work when the driver is built-in while the sequencer
is module. We check with IS_REACHABLE() and enable only when the
sequencer is in the same level of build.
However, this is basically a overshoot. The binder code
(snd-seq-device) is an individual module from the sequencer core
(snd-seq), and we just have to make the former a built-in while
keeping the latter a module for allowing the scenario like the above.
This patch achieves that by rewriting Kconfig slightly. Now, a driver
that provides the manual sequencer device binding should select
CONFIG_SND_SEQ_DEVICE in a way as
select SND_SEQ_DEVICE if SND_SEQUENCER != n
Note that the "!=n" is needed here to avoid the influence of the
sequencer core is module while the driver is built-in.
Also, since rawmidi.o may be linked with snd_seq_device.o when
built-in, we have to shuffle the code to make the linker happy.
(the kernel linker isn't smart enough yet to handle such a case.)
That is, snd_seq_device.c is moved to sound/core from sound/core/seq,
as well as Makefile.
Last but not least, the patch replaces the code using IS_REACHABLE()
with IS_ENABLED(), since now the condition meets always when enabled.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rewrite the complex ifdef condition with IS_REACHABLE().
The ifdef in opl4_local.h was without defined(MODLE) check, but this
is likely the oversight. Use IS_REACHABLE() here as well.
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some are replaced with the new ifdef CONFIG_SND_PROC_FS. Some are
removed by building opl4_proc.o conditionally.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Takashi Iwai
Joe Perches
Paul Gortmaker
Tejun Heo
Ingo Molnar
Linus Torvalds