Based on an original patch from Michael Schmitz:
Because mem_init() is now called before device init, devices that rely on
ST-RAM may find all ST-RAM already allocated to other users by the time
device init happens. In particular, a large initrd RAM disk may use up
enough of ST-RAM to cause atari_stram_alloc() to resort to
__get_dma_pages() allocation.
In the current state of Atari memory management, all of RAM is marked
DMA capable, so __get_dma_pages() may well return RAM that is not in actual
fact DMA capable. Using this for frame buffer or SCSI DMA buffer causes
subtle failure.
The ST-RAM allocator has been changed to allocate memory from a pool of
reserved ST-RAM of configurable size, set aside on ST-RAM init (i.e.
before mem_init()). As long as this pool is not exhausted, allocation of
real ST-RAM can be guaranteed.
Other changes:
- Replace the custom allocator in the ST-RAM pool by the existing allocator
in the resource subsystem,
- Remove mem_init_done and its hook, as memory init is now done before
device init,
- Remove /proc/stram, as ST-RAM usage now shows up under /proc/iomem, e.g.
005f2000-006f1fff : ST-RAM Pool
005f2000-0063dfff : atafb
0063e000-00641fff : ataflop
00642000-00642fff : SCSI
Signed-off-by: Michael Schmitz <schmitz@debian.org>
[Andreas Schwab <schwab@linux-m68k.org>: Use memparse()]
[Geert: Use the resource subsystem instead of a custom allocator]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:
linux/atomic.h
-> asm/atomic.h
-> asm-generic/atomic-long.h
where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype. This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.
Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).
Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harmonise these return values with other architectures. In some cases
this affects all compilers and in other cases non-gcc compilers only.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ulrich Drepper <drepper@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ poleg@redhat.com: no need to declare show_regs() in ptrace.h, sched.h does this ]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: Revive reporting of spurious interrupts
m68knommu: Move forward declaration of do_IRQ() from machdep.h to irq.h
m68k: fix some atomic operation asm address modes for ColdFire
m68k: use CPU_HAS_NO_BITFIELDS for signal functions
m68k: merge and clean up delay.h files
m68knommu: correctly use trap_init
m68knommu: merge ColdFire 5206 and 5206e platform code
m68k: merge mmu and non-mmu bitops.h
m68k: merge MMU and non MMU versions of system.h
m68k: merge MMU and non-MMU versions of asm/hardirq.h
m68k: merge the non-mmu and mmu versions of module.c
m68knommu: Fix printk() format in free_initrd_mem()
m68knommu: Make empty_zero_page "void *", like on m68k
The address limit is already set in flush_old_exec() so those calls to
set_fs(USER_DS) are redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not machine-specific, but common irq infrastructure.
Also add the missing asmlinkage, to match its definition.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire processors have a much more limited set of addressing modes
that can be used for most instructions. A number of the atomic operations
have already been fixed to limit the addressing modes used with add and
sub instructions when building for ColdFire. But we missed a few.
Fix the remaining atomic operations to be clean for ColdFire processors.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
When reworking bitops.h to be clean for all processor types we introduced
a CONFIG_CPU_HAS_NO_BITFIELDS define to signal whether this processor type
supported the bit field instructions. The ARCH_SIG_BITOPS functions for
m68k use these instruction types. We should base the use of these functions
(or the generic versions) on the CONFIG_CPU_HAS_NO_BITFIELDS define.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The real difference between the mmu and non-mmu varients of the delay.h
files has nothing to do with having an mmu or not. It is processor family
differences that means slightly different code. Merge the delay_mm.h and
delay_no.h files back into a single file.
The primarly difference we need to deal with is whether the processor
supports a 32bit * 32bit -> 64bit multiply. Without it we need to do some
shift scaling as well as use a 32bit * 32bit -> 32bit multiply. If building
for a multi-CPU type kernel then we must use the simpler mult/shift scaling.
This version of delay code allows the CPU32 family to use a 64bit mul,
since it supports this instruction, the old code did not.
The changes use macros where appropriate to try and optimize constant sized
udelay times. And it removes the use of a fixed lib function for the non-mmu
case. Code size on typical kernel configurations is similar, or only larger
by a few tens of bytes.
Also removed the unused muldiv() code from delay_mm.h.
Build and run tested on ColdFire and ARAnyM. Build tested only on 68328
and 68360 (CPU32).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently trap_init() is an empty function for m68knommu. Instead
the vectors are being setup as part of the IRQ initialization.
This is inconsistent with m68k and other architectures.
Change the local init_vectors() to be trap_init(), and init the
vectors at the correct time during startup. This will help merge of
m68k and m68knommu trap code in the furture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The following patch merges the mmu and non-mmu versions of the m68k
bitops.h files. Now there is a good deal of difference between the two
files, but none of it is actually an mmu specific difference. It is
all about the specific m68k/coldfire varient we are targeting. So it
makes an awful lot of sense to merge these into a single bitops.h.
There is a number of ways I can see to factor this code. The approach
I have taken here is to keep the various versions of each macro/function
type together. This means that there is some ifdefery with each to handle
each CPU type.
I have added some comments in a couple of appropriate places to try
and make it clear what the differences we are dealing with are.
Specifically the instruction and addressing mode differences we have
to deal with.
The merged form keeps the same underlying optimizations for each CPU
type for all the general bit clear/set/change and find bit operations.
It does switch to using the generic le operations though, instead of
any local varients.
Build tested on ColdFire, 68328, 68360 (which is cpu32) and 68020+.
Run tested on ColdFire and ARAnyM.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
The non-MMU m68k targets can use the same asm/system.h as the MMU
targets. So switch the current system_mm.h to be system.h and remove
system_no.h.
The assembly support code for the non-MMU resume functions needs to
be modified to match the now common switch_to() macro. Specifically
this means correctly saving and restoring the status flags in the case
of the ColdFire resume, and some reordering of the code to not use
registers before they are saved or after they are restored.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The contents of asm/hardirq.h are pretty strait forward for both the
MMU (hardirq_mm.h) and non-MMU (hardirq_no.h) include files. Merge the
two back into a single file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The non-mmu and mmu versions of the module loader module.c are
nearly identical. Merge them back to a single module.c. There is
a little bit of re-ordering of the struct and enum definitions in
module.h to keep the ifdefery to a minimum.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The implementation of find_next_bit_le() on m68knommu is identical with
the generic implementation of find_next_bit_le().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The style that we normally use in asm-generic is to test the macro itself
for existence, so in asm-generic, do:
#ifndef find_next_zero_bit_le
extern unsigned long find_next_zero_bit_le(const void *addr,
unsigned long size, unsigned long offset);
#endif
and in the architectures, write
static inline unsigned long find_next_zero_bit_le(const void *addr,
unsigned long size, unsigned long offset)
#define find_next_zero_bit_le find_next_zero_bit_le
This adds the #define for each of the optimized find bitops in the
architectures.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68knommu can't build ext4, udf, and ocfs2 due to the lack of
find_next_bit_le().
This implements find_next_bit_le() on m68knommu by duplicating the generic
find_next_bit_le() in lib/find_next_bit.c.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68knommu can use generic implementation of ext2 atomic bitops.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The implementation of iounmap() and __ioremap() for non-mmu m68k is
trivial. We can inline them in m68knommu headers and remove the trivial
implementations.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
The Atari keyboard driver calls atari_mouse_interrupt_hook if it's set, not
atari_input_mouse_interrupt_hook. Fix below.
[geert] Killed off atari_mouse_interrupt_hook completely, after fixing another
incorrect assignment in atarimouse.c.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
find_next bitops on m68k (find_next_zero_bit, find_next_bit, and
find_next_bit_le) may cause out of bounds memory access
when the bitmap size in bits % 32 != 0 and offset (the bitnumber
to start searching at) is very close to the bitmap size.
For example,
unsigned long bitmap[2] = { 0, 0 };
find_next_bit(bitmap, 63, 62);
1. find_next_bit() tries to find any set bits in bitmap[1],
but no bits set.
2. Then find_first_bit(bimap + 2, -1)
3. Unfortunately find_first_bit() takes unsigned int as the size argument.
4. find_first_bit will access bitmap[2~] until it find any set bits.
Add missing tests for stepping beyond the end of the bitmap to all
find_{first,next}_*() functions, and make sure they never return a value
larger than the bitmap size.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Hence use "offset" in find_next_{,zero_}bit(), like is already done for
find_next_{,zero_}bit_le()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The patch below changes a typo occcured to occurred in two comments.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no user now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a preparation for moving minix bit operations from asm/bitops.h to
architecture independent code in minix filesystem, this removes inline asm
from minix_find_first_zero_bit() for m68k.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations by renaming native ext2 bit
operations. The ext2 bit operations are kept as wrapper macros using
little-endian bit operations to maintain bisectability until the
conversions are finished.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations by renaming native ext2 bit
operations and changing find_*_bit_le() to take a "void *". The ext2 bit
operations are kept as wrapper macros using little-endian bit operations
to maintain bisectability until the conversions are finished.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/block: amiflop - Remove superfluous amiga_chip_alloc() cast
m68k/atari: ARAnyM - Add support for network access
m68k/atari: ARAnyM - Add support for console access
m68k/atari: ARAnyM - Add support for block access
m68k/atari: Initial ARAnyM support
m68k: Kconfig - Remove unneeded "default n"
m68k: Makefiles - Change to new flags variables
m68k/amiga: Reclaim Chip RAM for PPC exception handlers
m68k: Allow all kernel traps to be handled via exception fixups
m68k: Use base_trap_init() to initialize vectors
m68k: Add helper function handle_kernel_fault()
Add improved support for running under the ARAnyM emulator
(Atari Running on Any Machine - http://aranym.org/).
[michael, geert: Cleanups and updates]
Signed-off-by: Petr Stehlik <pstehlik@sophics.cz>
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add helper function handle_kernel_fault() in signal.c, so frame_extra_sizes
can become static, and to avoid future code duplication.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The EDGE Port module of some ColdFire parts using the intc-simr interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The EDGE Port module of some ColdFire parts using the intc-2 interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The reality is that you do not need the abiltity to configure the
clock divider for ColdFire CPUs. It is a fixed ratio on any given
ColdFire family member. It is not the same for all ColdFire parts,
but it is always the same in a model range. So hard define the divider
for each supported ColdFire CPU type and remove the Kconfig option.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Most ColdFire CPUs have an internal peripheral set that can be mapped at
a user selectable address. Different ColdFire parts either use an MBAR
register of an IPSBAR register to map the peripheral region. Most boards
use the Freescale default mappings - but not all.
Make the setting of the MBAR or IPSBAR register configurable. And only make
the selection available on the appropriate ColdFire CPU types.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Different ColdFire CPUs have different ways of defining where their
internal peripheral registers sit in their address space. Some use an
MBAR register, some use and IPSBAR register, some have a fixed mapping.
Now that most of the peripheral address definitions have been cleaned up
we can clean up the setting of the MBAR and IPSBAR defines to limit them
to just where they are needed (and where they actually exist).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In some of the RAM size autodetection code on ColdFire CPU startup
we reference DRAM registers relative to the MBAR register. Not all of
the supported ColdFire CPUs have an MBAR, and currently this works
because we fake an MBAR address on those registers. In an effort to
clean this up, and eventually remove the fake MBAR setting make the
DRAM register address definitions actually contain the MBAR (or IPSBAR
as appropriate) value as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Not all ColdFire CPUs that use the old style timer hardware module use
an MBAR set peripheral region. Move the TIMER base address defines to the
per-CPU header files where we can set it correctly based on how the
peripherals are mapped - instead of using a fake MBAR for some platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The base addresses of the ColdFire DMA unit registers belong with
all the other address definitions in the per-cpu headers. The current
definitions assume they are relative to an MBAR register. Not all
ColdFire CPUs have an MBAR register. A clean address define can only
be acheived in the per-cpu headers along with all the other chips
peripheral base addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 528x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 527x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 523x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5207 and 5208 CPUs have fixed peripheral addresses.
They do not use the setable peripheral address registers like the MBAR
and IPSBAR used on many other ColdFire parts. Don't use fake values
of MBAR and IPSBAR when using peripheral addresses for them, there
is no need to.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The PIT hardware timer module used in some ColdFire CPU's is not always
addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and
5208 have fixed peripheral addresses. So lets not define the register
addresses of the PIT relative to an IPSBAR definition. Move the base
address definitions into the per-part headers. This is a lot more consistent
since all the other peripheral base addresses are defined in the per-part
header files already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the bogus definition of the MBAR register for the ColdFire 532x
family. It doesn't have an MBAR register, its peripheral registers are
at fixed addresses and are not relative to a settable base.
All the code that relyed on this definition existing has been cleaned
up. The register address definitions now include the base as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 54xx family shares the same interrupt controller used
on the 523x, 527x and 528x ColdFire parts, but it isn't offset
relative to the IPSBAR register. The 54xx doesn't have an IPSBAR
register.
By including the base address of the peripheral registers in the register
definitions (MCFICM_INTC0 and MCFICM_INTC1 in this case) we can avoid
having to define a fake IPSBAR for the 54xx. And this makes the register
address definitions of these more consistent, the majority of the other
register address defines include the peripheral base address already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MBAR2 register is only used on the ColdFire 5249 part, so move its
definition out of the common coldfire.h and into the 5249 support header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).
This also goes part of the way to fixing a regression caused by commit
ea61bc461d ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.
This also goes part of the way to fixing a regression caused by commit
ea61bc461d ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
It's a way too generic name for a global #define and conflicts with a variable
with the same name, causing build errors like:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c: In function ‘_si_clkctl_cc’:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected identifier or ‘(’ before ‘volatile’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected ‘)’ before ‘(’ token
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1421: error: incompatible types in assignment
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1422: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1423: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1424: error: invalid operands to binary |
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: incompatible type for argument 4 of ‘bcmsdh_reg_write’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1428: error: invalid operands to binary &
| make[8]: *** [drivers/staging/brcm80211/brcmfmac/../util/siutils.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Some versions of gcc replace calls to strstr() with single-character
"needle" string parameters by calls to strchr() behind our back.
If strchr() is defined as an inline function, this causes linking errors
like
ERROR: "strchr" [drivers/target/target_core_mod.ko] undefined!
As m68k is the only architecture that has an inline strchr() and this
inline version is not an optimized asm version, uninline strchr() and use
the standard out-of-line C version in lib/string.c instead.
This also decreases the defconfig/allmodconfig kernel image sizes by a few
hundred bytes.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (25 commits)
m68knommu: fix broken setting of irq_chip and handler
m68knommu: switch to using -mcpu= flags for ColdFire targets
m68knommu: arch/m68knommu/Kconfig whitespace cleanup
m68knommu: create optimal separate instruction and data cache for ColdFire
m68knommu: support ColdFire caches that do copyback and write-through
m68knommu: support version 2 ColdFire split cache
m68knommu: make cache push code ColdFire generic
m68knommu: clean up ColdFire cache control code
m68knommu: move inclusion of ColdFire v4 cache registers
m68knommu: merge bit definitions for version 3 ColdFire cache controller
m68knommu: create bit definitions for the version 2 ColdFire cache controller
m68knommu: remove empty __iounmap() it is no used
m68knommu: remove kernel_map() code, it is not used
m68knommu: remove do_page_fault(), it is not used
m68knommu: use user stack pointer hardware on some ColdFire cores
m68knommu: remove command line printing DEBUG
m68knommu: remove fasthandler interrupt code
m68knommu: move UART addressing to part specific includes
m68knommu: fix clock rate value reported for ColdFire 54xx parts
m68knommu: move ColdFire CPU names into their headers
...
and saner do_signal() arguments, while we are at it
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Since commit 31c911329e ("mm: check the argument
of kunmap on architectures without highmem"), we get lots of warnings like
arch/m68k/kernel/sys_m68k.c:508: warning: passing argument 1 of ‘kunmap’ from incompatible pointer type
As m68k doesn't support highmem anyway, open code the calls to kmap() and
kunmap() (the latter is a no-op) to kill the warnings, like is done on most
other architectures without CONFIG_HIGHPTE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Creasey <sammy@sammy.net>
Create separate functions to deal with instruction and data cache flushing.
This way we can optimize them for the vairous cache types and arrangements
used across the ColdFire family.
For example the unified caches in the version 3 cores means we don't
need to flush the instruction cache. For the version 2 cores that do
not do data cacheing (or where we choose instruction cache only) we
don't need to do any data flushing.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The version 3 and version 4 ColdFire cache controllers support both
write-through and copy-back modes on the data cache. Allow for Kconfig
time configuration of this, and set the cache mode appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The newer version 2 ColdFire CPU cores support a configurable cache
arrangement. The cache memory can be used as all instruction cache, all
data cache, or split in half for both instruction and data caching.
Support this setup via a Kconfig time menu that allows a kernel builder
to choose the arrangement they want to use.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently the code to push cache lines is only available to version 4
cores. Version 3 cores may also need to use this if we support copy-
back caches on them. Move this code to make it more generic, and
useful for all version ColdFire cores.
With this in place we can now have a single cache_flush_all() code
path that does all the right things on all version cores.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The cache control code for the ColdFire CPU's is a big ugly mess
of "#ifdef"ery liberally coated with bit constants. Clean it up.
The cache controllers in the various ColdFire parts are actually quite
similar. Just differing in some bit flags and options supported. Using
the header defines now in place it is pretty easy to factor out the
small differences and use common setup and flush/invalidate code.
I have preserved the cache setups as they where in the old code
(except where obviously wrong - like in the case of the 5249). Following
from this it should be easy now to extend the possible setups used on
the CACHE controllers that support split cacheing or copy-back or
write through options.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Move the inclusion of the version 4 cache controller registers so that
it is with all the other register bit flag definitions. This makes it
consistent with the other version core inclusion points, and means we
don't need "#ifdef"ery in odd-ball places for these definitions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All version 3 based ColdFire CPU cores have a similar cache controller.
Merge all the exitsing definitions into a single file, and make them
similar in style and naming to the existing version 2 and version 4
cache controller definitions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The version 2 ColdFire CPU based cores all contain a similar cache
controller unit. Create a set of bit flag definitions for the supporting
registers.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The more modern ColdFire parts (even if based on older version cores)
have separate user and supervisor stack pointers (a7 register).
Modify the ColdFire CPU setup and exception code to enable and use
this on parts that have it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire UART base addresses varies between the different ColdFire
family members. Instead of keeping the base addresses with the UART
definitions keep them with the other addresses definitions for each
ColdFire part.
The motivation for this move is so that when we add new ColdFire
part definitions, they are all in a single file (and we shouldn't
normally need to modify the UART definitions in mcfuart.h at all).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The instruction timings of the ColdFire 54xx family parts are
different to other version 4 parts (or version 2 or 3 parts for
that matter too).
Move the instruction timing setting into the ColdFire part
specific headers, and set the 54xx value appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Move the ColdFire CPU names out of setup.c and into their repsective
headers. That way when we add new ones we won't need to modify
setup.c any more.
Add the missing 548x CPU name.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 547x family of processors is very similar to the ColdFire
548x series. Almost all of the support for them is the same. Make the
code supporting the 548x more gneric, so it will be capable of
supporting both families.
For the most part this is a renaming excerise to make the support
code more obviously apply to both families.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Now that we have meaningfull symbolic constants for bit definitions
of the cache registers of m5407 and m548x chips, use them to
improve readability, portability and efficiency of the cache operations.
This also fixes __flush_cache_all for m548x chips : implicit
DCACHE_SIZE was exact for m5407, but wrong for m548x.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
__flush_cache_all for m54xx is intrinsically related to the bit
definitions in m54xxacr.h. Move it there from cacheflush_no.h,
for easier maintenance.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MCF548x have the same cache control registers as the MCF5407.
Extract the bit definitions for the ACR and CACR registers from m5407sim.h
and move them to a new file m54xxacr.h. Those definitions are not used
anywhere yet, so no other file is involved. This is a preparation for
m54xx cache support cleanup.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Recent changes to header files made kernel compilation for m68k/m68knommu
fail with :
CC arch/m68knommu/kernel/asm-offsets.s
In file included from /archives/linux/git/arch/m68k/include/asm/system.h:2,
from include/linux/wait.h:25,
from include/linux/mmzone.h:9,
from include/linux/gfp.h:4,
from include/linux/irq.h:20,
from include/asm-generic/hardirq.h:12,
from /archives/linux/git/arch/m68k/include/asm/hardirq_no.h:17,
from /archives/linux/git/arch/m68k/include/asm/hardirq.h:2,
from include/linux/hardirq.h:10,
from /archives/linux/git/arch/m68k/include/asm/irqflags.h:5,
from include/linux/irqflags.h:15,
from include/linux/spinlock.h:53,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:56,
from arch/m68knommu/kernel/asm-offsets.c:12:
/archives/linux/git/arch/m68k/include/asm/system_no.h: In function ‘__xchg’:
/archives/linux/git/arch/m68k/include/asm/system_no.h:79: error: implicit
+declaration of function ‘local_irq_save’
/archives/linux/git/arch/m68k/include/asm/system_no.h:101: error: implicit
+declaration of function ‘local_irq_restore’
Fix that
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The cleanup and merge of machdep should not have removed the do_IRQ
declaration. It is needed by the 68328 based targets.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Long ago, PT_TRACESYS_OFF and friends were introduced as hard defines to
avoid straight constants in assembler parts of linux m68k. They are not
used anymore, and were not updated to follow changes in linux kernel.
Remove them. When similar constants are needed, they are now generated
using asm-offsets.c.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we no longer need to provide KM_type, the whole pte_*map_nested()
API is now redundant, remove it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68knommu: convert to using tracehook_report_syscall_*
m68knommu: some boards use fixed phy for FEC ethernet
m68knommu: support the external GPIO based interrupts of the 5272
m68knommu: mask of vector bits in exception word properly
m68knommu: change to new flag variables
m68knommu: Fix MCFUART_TXFIFOSIZE for m548x.
m68knommu: add basic mmu-less m548x support
m68knommu: .gitignore vmlinux.lds
m68knommu: stop using __do_IRQ
m68knommu: rename PT_OFF_VECTOR to PT_OFF_FORMATVEC.
m68knommu: add support for Coldfire 547x/548x interrupt controller
m68k{nommu}: Remove unused DEFINE's from asm-offsets.c
m68knommu: whitespace cleanup in 68328/entry.S
m68knommu: Document supported chips in intc-2.c and intc-simr.c.
m68knommu: fix strace support for 68328/68360
m68knommu: fix default starting date
arch/m68knommu: Removing dead 68328_SERIAL_UART2 config option
arch/m68knommu: Removing dead RAM_{16,32}_MB config option
arch/m68knommu: Removing dead M68KFPU_EMU config option
arch/m68knommu: Removing dead RELOCATE config option
...
On m68k, I/O macros like inb() outw() etc. are only defined to
something useful if CONFIG_ISA is set; dummies are in place if
not, but four macros were missing from the !CONFIG_ISA case.
Adding these makes some drivers, such as speakup, compile again.
Signed-off-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes this:
drivers/char/mem.c: In function 'mmap_kmem':
drivers/char/mem.c:342: warning: cast to pointer from integer of different size
by doing what other archtiectures do.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The MMU and non-MMU versions of traps.h are virtually identical,
merge them into a single file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The MMU and non-MMU versions of thread_info.h are quite similar.
Merge the two files.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The only difference between the MMU and non-MMU versions of atomic.h
is some extra support needed by ColdFire family processors. So merge
this into the MMU version of atomic.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is a lot of common defines in the MMU and non-MMU variants of
page.h. Factor out the common stuff into the master page.h. It still
includes the underlying page_mm.h or page_no.h, but they only contain
the real differences now.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
No need to have separate machdep.h files for each of the MMU and non-MMU
cases. Merge them all into a single file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The MMU and non-MMU string.h varients (string_no.h and string_mm.h)
and almost the same. Switch to using the string_mm.h one, merging
in the necessary ColdFire support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CONFIG_SMP doesn't exist in Kconfig (for this architecure), therefore
remove all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move the definition of THREAD_SIZE from page_mm.h to thread_info_mm.h
This logically associates it with the other thread definitions, and will
make it easier to merge the MMU and non-MMU versions of page.h and
thread_info.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch converts m68k to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- m68k defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCSRS485 and TIOCGRS485m which are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CONFIG_GG2 doesn't exist in Kconfig, therefore remove
all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Serial lines on the MCF548x have really big fifos : 512 bytes.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add a very basic mmu-less support for coldfire m548x family. This is perhaps
also valid for m547x family. The port comprises the serial, tick timer and
reboot support. The gpio part compiles but is empty. This gives a functional
albeit limited linux for the m548x coldfire family. This has been tested
on a Freescale M548xEVB Lite board with a M5484 processor and the default
dbug monitor.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
The arch/m68k/include/asm/ide.h produces errors when the IDE driver is compiled for my 523x uClinux system under kernel. The header makes some redefines of operators not defined in the arch/m68k/include/asm/io_no.h header. There are no separate mmio and iospace defines.
Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now each architecture has the own dma_get_cache_alignment implementation.
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.
This patch:
dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.
Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
This patch is against the 2.6.34 source.
Paraphrased from the 1989 BSD patch by David Borman @ cray.com:
These are the changes needed for the kernel to support
LINEMODE in the server.
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
New ioctl:
TIOCSIG Generate a signal to processes in the
current process group of the pty.
There is a new mode for packet driver, the TIOCPKT_IOCTL bit.
When packet mode is turned on in the pty, and the EXTPROC bit
is set, then whenever the state of the pty is changed, the
next read on the master side of the pty will have the TIOCPKT_IOCTL
bit set. This allows the process on the server side of the pty
to know when the state of the terminal has changed; it can then
issue the appropriate ioctl to retrieve the new state.
Since the original BSD patches accompanied the source code for telnet
I've left that reference here, but obviously the feature is useful for
any remote terminal protocol, including ssh.
The corresponding feature has existed in the BSD tty driver since 1989.
For historical reference, a good copy of the relevant files can be found
here:
http://anonsvn.mit.edu/viewvc/krb5/trunk/src/appl/telnet/?pathrev=17741
Signed-off-by: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removal of these started in 2.3.43pre3, ca. 10 years ago.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 64bit, local_t is of size long, and thus we make local64_t an alias.
On 32bit, we fall back to atomic64_t. (architecture can provide optimized
32-bit version)
(This new facility is to be used by perf events optimizations.)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-arch@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
arch/m68knommu/platform/68360/commproc.c: Checkpatch cleanup
arch/m68knommu/mm/fault.c: Checkpatch cleanup
m68knommu: improve short help of m68knommu/Kconfig/RAMSIZE for '0' case
m68knommu: remove un-used mcfsmc.h
m68knommu: add smc91x support for ColdFire NETtel boards
m68knommu: add smc91x support to ColdFire 5249 platform
m68knommu: remove size limit on non-MMU TASK_SIZE
m68knommu: fix broken use of BUAD_TABLE_SIZE in 68328serial driver
m68knommu: Coldfire QSPI platform support
Remove the un-used mcfsmc.h. All ColdFire platforms that use SMC ethernet
devices are platform enabled to use the smc91x driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The TASK_SIZE define is used in some places as a limit on the size of
the virtual address space of a process. On non-MMU systems those addresses
used in comparison will be physical addresses, and they could be anywhere
in the 32bit physical address space. So for !CONFIG_MMU systems set the
TASK_SIZE to the maximum physical address.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
linux-next:
fs/udf/balloc.c: In function 'udf_bitmap_new_block':
fs/udf/balloc.c:274: error: implicit declaration of function 'generic_find_next_le_bit'
Convert ext2_find_next_{zero_,}bit() into generic_find_next_{zero_,}le_bit(),
and wrap the ext2_find_next_{zero_,}bit() around the latter.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In preparation for removing volatile from the atomic_t definition, this
patch adds a volatile cast to all the atomic read functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware. This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix tcdrain on coldfire uarts.
Currently with coldfire uarts tcdrain returns without waiting for txempty,
because (tx)fifosize is 0. Fix that and call uart_update_timeout when
setting the baud rate, otherwise tcdrain will wait for an half our :)
Also constify mcf_uart_ops.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Recently, we started seeing this on allmodconfig builds:
CC mm/memcontrol.o
{standard input}: Assembler messages:
{standard input}:4076: Error: operands mismatch -- statement `subl 12(%fp),170(%a0)' ignored
Correct the asm constraint, like done for m68knommu.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
LibSegFault uses piggybacks sc_fpstate field of the `struct sigcontext'
and this patch avoids LibSegFault overflowing this field. Also this
removes an unnecessary divergence from classic m68k.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
While in theory user_enable_single_step/user_disable_single_step/
user_enable_blockstep could also be provided as an inline or macro there's
no good reason to do so, and having the prototype in one places keeps code
size and confusion down.
Roland said:
The original thought there was that user_enable_single_step() et al
might well be only an instruction or three on a sane machine (as if we
have any of those!), and since there is only one call site inlining
would be beneficial. But I agree that there is no strong reason to care
about inlining it.
As to the arch changes, there is only one thought I'd add to the
record. It was always my thinking that for an arch where
PTRACE_SINGLESTEP does text-modifying breakpoint insertion,
user_enable_single_step() should not be provided. That is,
arch_has_single_step()=>true means that there is an arch facility with
"pure" semantics that does not have any unexpected side effects.
Inserting a breakpoint might do very unexpected strange things in
multi-threaded situations. Aside from that, it is a peculiar side
effect that user_{enable,disable}_single_step() should cause COW
de-sharing of text pages and so forth. For PTRACE_SINGLESTEP, all these
peculiarities are the status quo ante for that arch, so having
arch_ptrace() itself do those is one thing. But for building other
things in the future, it is nicer to have a uniform "pure" semantics
that arch-independent code can expect.
OTOH, all such arch issues are really up to the arch maintainer. As
of today, there is nothing but ptrace using user_enable_single_step() et
al so it's a distinction without a practical difference. If/when there
are other facilities that use user_enable_single_step() and might care,
the affected arch's can revisit the question when someone cares about
the quality of the arch support for said new facility.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the ipc demultiplexer syscall. Except for
s390 and sparc64 all implementations of the sys_ipc are nearly identical.
There are slight differences in the types of the parameters, where mips
and powerpc as the only 64-bit architectures with sys_ipc use unsigned
long for the "third" argument as it gets casted to a pointer later, while
it traditionally is an "int" like most other paramters. frv goes even
further and uses unsigned long for all parameters execept for "ptr" which
is a pointer type everywhere. The change from int to unsigned long for
"third" and back to "int" for the others on frv should be fine due to the
in-register calling conventions for syscalls (we already had a similar
issue with the generic sys_ptrace), but I'd prefer to have the arch
maintainers looks over this in details.
Except for that h8300, m68k and m68knommu lack an impplementation of the
semtimedop sub call which this patch adds, and various architectures have
gets used - at least on i386 it seems superflous as the compat code on
x86-64 and ia64 doesn't even bother to implement it.
[akpm@linux-foundation.org: add sys_ipc to sys_ni.c]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the old mmap() syscall, which expects its
argument in a memory block and switch all architectures over to use it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the old select() syscall, which expects
its argument in a memory block and switch all architectures over to use
it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Acked-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch defines sigcontext ABI of ColdFire. Due to ISA
restrictions ColdFire needs different rt_sigreturn trampoline.
And due to ColdFire FP registers being 8-bytes instead of 12-bytes on
m68k, sigcontext and fpregset structures should be updated.
Regarding the sc_fpstate[16+6*8] field, it would've been enough 16
bytes to store ColdFire's FP state. To accomodate GLIBC's libSegFault
it would'be been enough 6*8 bytes (room for the 6 non-call-clobbered
FP registers). I set it to 16+6*8 to provide some extra space for any
future changes in the ColdFire FPU.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Port syscalls for NPTL support to m68knommu.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch adds several syscalls, that provide necessary
functionality to support NPTL on m68k/ColdFire.
The syscalls are get_thread_area, set_thread_area, atomic_cmpxchg_32 and
atomic_barrier.
The cmpxchg syscall is required for ColdFire as it doesn't support 'cas'
instruction.
Also a ptrace call PTRACE_GET_THREAD_AREA is added to allow debugger to
inspect the TLS storage.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch switches m68k to generic siginfo layout. The custom layout
of m68k's `struct siginfo' had several issues due to not considering
aliasing of members in the union, e.g., _uid32 was at different offsets
in ._kill, ._rt and ._sigchld.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove the old 68k Mac serial port code and a lot of related cruft. Add
new SCC platform devices to mac 68k platform.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
On VIVT ARM, when we have multiple shared mappings of the same file
in the same MM, we need to ensure that we have coherency across all
copies. We do this via make_coherent() by making the pages
uncacheable.
This used to work fine, until we allowed highmem with highpte - we
now have a page table which is mapped as required, and is not available
for modification via update_mmu_cache().
Ralf Beache suggested getting rid of the PTE value passed to
update_mmu_cache():
On MIPS update_mmu_cache() calls __update_tlb() which walks pagetables
to construct a pointer to the pte again. Passing a pte_t * is much
more elegant. Maybe we might even replace the pte argument with the
pte_t?
Ben Herrenschmidt would also like the pte pointer for PowerPC:
Passing the ptep in there is exactly what I want. I want that
-instead- of the PTE value, because I have issue on some ppc cases,
for I$/D$ coherency, where set_pte_at() may decide to mask out the
_PAGE_EXEC.
So, pass in the mapped page table pointer into update_mmu_cache(), and
remove the PTE value, updating all implementations and call sites to
suit.
Includes a fix from Stephen Rothwell:
sparc: fix fallout from update_mmu_cache API change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix compilation breakage of all m68knommu targets:
CC arch/m68knommu/kernel/asm-offsets.s
In file included from include/linux/sched.h:77,
from arch/m68knommu/kernel/asm-offsets.c:12:
include/linux/percpu.h: In function 'per_cpu_ptr_to_phys':
include/linux/percpu.h:161: error: implicit declaration of function 'virt_to_phy
This is broken in linux-2.6.33-rc3.
Change the definitions of __pa() and __va() to not use virt_to_phys()
and phys_to_virt(). Trivial 1:1 conversion required for the non-MMU case.
A side effect if this is that the m68knommu can now use asm/virtconvert.h
for the definition of virt_to_phys() and phys_to_virt().
Also cleaned up the definition of page_to_phys() when moving into
virtconvert.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
Currently all architectures but microblaze unconditionally define
USE_ELF_CORE_DUMP. The microblaze omission seems like an error to me, so
let's kill this ifdef and make sure we are the same everywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Simek <michal.simek@petalogix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
The simplest method was to add an extra asm-offsets.h
file in arch/$ARCH/include/asm that references the generated file.
We can now migrate the architectures one-by-one to reference
the generated file direct - and when done we can delete the
temporary arch/$ARCH/include/asm/asm-offsets.h file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: export clk_* symbols in clk.c
m68knommu: Split the .init section into INIT_TEXT_SECTION and INIT_DATA_SECTION.
m68knommu: Move __init_end out of the .init section.
m68knommu: Move __init_begin out of the .init section.
m68knommu: Use more macros inside the .init section.
m68knommu: Use INIT_TASK_DATA and CACHELINE_ALIGNED_DATA.
m68knommu: Make THREAD_SIZE available to assembly files.
m68knommu: Don't hardcode the value of PAGE_SIZE in the linker script.
m68knommu: rename BSS define in linker script
m68knommu: add a task_pt_regs() macro
m68knommu: define arch_has_single_step() and friends
m68knommu: add uboot commandline argument passing support
m68knommu: Coldfire GPIO corrections
m68knommu: move mcf_remove to .devexit.text
Fixed up (?) conflict in arch/m68k/include/asm/ptrace.h
On SUN3, m68k defines macro VMALLOC_END as unsigned long variable
vmalloc_end which is adjusted from mmu_emu_init(). This becomes
problematic if a local variables vmalloc_end is defined in some
function (not very unlikely) and VMALLOC_END is used in the function -
the function thinks its referencing the global VMALLOC_END value but
would be referencing its own local vmalloc_end variable.
Rename the global variable to m68k_vmlloc_end which is much less
likely to be used as local variable name.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: parport_mfc3 - Not makes it a bool before the comparison.
m68k: don't export static inline functions
fbdev: atafb - add palette register check
m68k: Remove the BKL from sys_execve
m68k: Cleanup linker scripts using new linker script macros.
m68k: Make thread_info.h usable from assembly.
m68knommu: define arch_has_single_step() and friends
m68k: ptrace fixes
m68k: use generic code for ptrace requests
rtc: Add an RTC driver for the Ricoh RP5C01
rtc: Add an RTC driver for the Oki MSM6242
[Geert] <asm/thread_info_mm.h> pulls in <asm/current.h>, which contains C only.
So the include must be moved inside #ifndef __ASSEMBLY__.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Towards adding CONFIG_UTRACE support for non-mmu m68k add
arch_has_single_step, and its support functions user_enable_single_step()
and user_disable_single_step().
[Geert] m68k conflict resolution from linux-next
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove all but PTRACE_{PEEK,POKE}USR and PTRACE_{GET,SET}{REGS,FPREGS}
from arch_ptrace and let the rest be handled by generic code. Define
PTRACE_SINGLEBLOCK to enable singleblock tracing.
[Geert] Not yet applicable for m68knommu
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Towards adding CONFIG_UTRACE support for non-mmu m68k add
arch_has_single_step, and its support functions user_enable_single_step()
and user_disable_single_step().
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Mtdblock driver doesn't call flush_dcache_page for pages in request. So,
this causes problems on architectures where the icache doesn't fill from
the dcache or with dcache aliases. The patch fixes this.
The ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE symbol was introduced to avoid
pointless empty cache-thrashing loops on architectures for which
flush_dcache_page() is a no-op. Every architecture was provided with this
flush pages on architectires where ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE is
equal 1 or do nothing otherwise.
See "fix mtd_blkdevs problem with caches on some architectures" discussion
on LKML for more information.
Signed-off-by: Ilya Loginov <isloginov@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Peter Horton <phorton@bitbox.co.uk>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Create a new socket level option to report number of queue overflows
Recently I augmented the AF_PACKET protocol to report the number of frames lost
on the socket receive queue between any two enqueued frames. This value was
exported via a SOL_PACKET level cmsg. AFter I completed that work it was
requested that this feature be generalized so that any datagram oriented socket
could make use of this option. As such I've created this patch, It creates a
new SOL_SOCKET level option called SO_RXQ_OVFL, which when enabled exports a
SOL_SOCKET level cmsg that reports the nubmer of times the sk_receive_queue
overflowed between any two given frames. It also augments the AF_PACKET
protocol to take advantage of this new feature (as it previously did not touch
sk->sk_drops, which this patch uses to record the overflow count). Tested
successfully by me.
Notes:
1) Unlike my previous patch, this patch simply records the sk_drops value, which
is not a number of drops between packets, but rather a total number of drops.
Deltas must be computed in user space.
2) While this patch currently works with datagram oriented protocols, it will
also be accepted by non-datagram oriented protocols. I'm not sure if thats
agreeable to everyone, but my argument in favor of doing so is that, for those
protocols which aren't applicable to this option, sk_drops will always be zero,
and reporting no drops on a receive queue that isn't used for those
non-participating protocols seems reasonable to me. This also saves us having
to code in a per-protocol opt in mechanism.
3) This applies cleanly to net-next assuming that commit
977750076d (my af packet cmsg patch) is reverted
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert 45d80eea87 ("m68k: convert to
asm-generic/hardirq.h") - it fails to compile due to an inclusion tangle:
In file included from include/linux/irq.h:12,
from include/asm-generic/hardirq.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq_mm.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq.h:4,
from include/linux/hardirq.h:10,
from /usr/src/devel/arch/m68k/include/asm/system_mm.h:69,
from /usr/src/devel/arch/m68k/include/asm/system.h:4,
from include/linux/list.h:7,
from include/linux/preempt.h:11,
from include/linux/spinlock.h:50,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:56,
from arch/m68k/kernel/asm-offsets.c:14:
include/linux/smp.h:17: error: field 'list' has incomplete type
Cc: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A number of architectures have identical asm/mman.h files so they can all
be merged by using the new generic file.
The remaining asm/mman.h files are substantially different from each
other.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a flag for mmap that will be used to request a huge page region that
will look like anonymous memory to user space. This is accomplished by
using a file on the internal vfsmount. MAP_HUGETLB is a modifier of
MAP_ANONYMOUS and so must be specified with it. The region will behave
the same as a MAP_ANONYMOUS region using small pages.
The patch also adds the MAP_STACK flag, which was previously defined only
on some architectures but not on others. Since MAP_STACK is meant to be a
hint only, architectures can define it without assigning a specific
meaning to it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric B Munson <ebmunson@us.ibm.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: David Rientjes <rientjes@google.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (53 commits)
m68knommu: Make PAGE_SIZE available to assembly files.
m68knommu: fix ColdFire definition of CLOCK_TICK_RATE
m68knommu: set multi-function pins for ethernet when enabled
m68knommu: remove special interrupt handling code for ne2k support
m68knommu: relax IO_SPACE_LIMIT setting
m68knommu: remove ColdFire direct interrupt register access
m68knommu: create a speciailized ColdFire 5272 interrupt controller
m68knommu: add support for second interrupt controller of ColdFire 5249
m68knommu: clean up old ColdFire timer irq setup
m68knommu: map ColdFire interrupts to correct masking bits
m68knommu: clean up ColdFire 532x CPU timer setup
m68knommu: simplify ColdFire "timers" clock initialization
m68knommu: support code to mask external interrupts on old ColdFire CPU's
m68knommu: merge old ColdFire interrupt controller masking macros
m68knommu: remove duplicate ColdFire mcf_autovector() code
m68knommu: move ColdFire INTC definitions to new include file
m68knommu: mask off all interrupts in ColdFire intc-simr controller
m68knommu: remove timer device interrupt setup for ColdFire 532x
m68knommu: remove interrupt masking from ColdFire pit timer
m68knommu: remove unecessary interrupt level setting in ColdFire 520x setup
...
The good definition of CLOCK_TICK_RATE for coldfires has been lost in the
merge of m68k and m68knommu include files. Restore it. Culprit :
commit ebafc17468
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The improved interrupt support for ColdFire CPU cores means we no
longer need all the interrupt setup and ack hacks to support the NE2000
driver on ColdFire platforms. Remove all that code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
There is really no limit to the addresses which can be used by the
in*() and out*() family of IO space calls in m68k non-MMU environments.
So don't impose an artificial address limit, allow the full 32bit range.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5272 CPU has a very different interrupt controller than
any of the other ColdFire parts. It needs its own controller code to
correctly setup and ack interrupts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5249 CPU has a second (compleletly different) interrupt
controller. It is the only ColdFire CPU that has this type. It controlls
GPIO interrupts amongst a number of interrupts from other internal
peripherals. Add support code for it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The older simple ColdFire interrupt controller has no one-to-one mapping
of interrupt numbers to bits in the interrupt mask register. Create a
mapping array that each ColdFire CPU type can populate with its available
interrupts and the bits that each use in the interrupt mask register.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The newer ColdFire 532x family of CPU's uses the old timer, but has a
newer interrupt controller. It doesn't need the special timer setup
that was required when using the older interrupt controller. Remove the
dead timer irq and level setting code, and define the hard coded vector.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire "timers" clock setup can be simplified. There is really no
need for the flexible per-platform setup code. The clock interrupt can be
hard defined per CPU platform (in CPU include files). This makes the
actual timer code simpler.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently the code that supports setting the old style ColdFire interrupt
controller mask registers is macros in the include files of each of the
CPU types. Merge all these into a set of real masking functions in the
old Coldfire interrupt controller code proper. All the macros are basically
the same (excepting a register size difference on really early parts).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Create an mcfintc.h include file with the definitions for the old style
ColdFire interrupt controller. They are only needed on CPU's that use
this old controller - so isolate them on their own.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire intc-simr interrupt controller should mask off all
interrupt sources at init time. Doing it here instead of separately
in each platform setup.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
With proper interrupt controller code in place there is no need for
devices like the timers to have custom interrupt masking code.
Remove it (and the defines that go along with it).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 532x family of parts uses 2 of the same INTC interrupt
controlers used in the ColdFire 520x family. So modify the code to
support both parts. The extra code for the second INTC controler in
the case of the 520x is easily optimized away to nothing.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Create general interrupt controller code for the ColdFire 520x family,
that does proper masking and unmasking of interrupts. With this in
place some of the driver hacks in place to support ColdFire interrupts
can finally go away.
Within the ColdFire family there is a variety of different interrupt
controllers in use. Some are used on multiple parts, some on only one.
There is quite some differences in some varients, so much so that
common code for all ColdFire parts would be impossible.
This commit introduces code to support one of the newer interrupt
controllers in the ColdFire 5208 and 5207 parts. It has very simple
mask and unmask operations, so is one of the easiest to support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The non-mmu version of dma.h contains a lot of ColdFire specific DMA
support, but also all of the base m68k support. So use the non-mmu
version of dma.h for all.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is reasonably strait forward to merge the mmu and non-mmu versions
of irq.h. Most of the defines and structs are not needed on non-mmu.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The mmu and non-mmu versions of processor.h have a lot of common code.
This is a strait forward merge. start_thread() could be improved, but
that is not quite as strait forward, leaving for a follow on change.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
The definition of MCFSIM_PADDR and MCFSIM_PADAT now has MCF_BAR already added in.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This adds the basic infrastructure used by all of the different Coldfire CPUs.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In order to be able to use asm-offsets.h in C files the
existing namespace conflicts must be solved first. In
asm-offsets.h there are defines for signal constants, so they
can be used in assembler files.
Unfortunately the existing defines use a 1:1 mapping for the
macro names which results in name space conflicts if the header
file would also be used in C files. So rename the created
defines and add an "L" prefix to each one since that has
already been done for the SIGTRAP define in entry_mm.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Horst Hartmann <horsth@linux.vnet.ibm.com>
Cc: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <20090831124416.998821502@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
m68k has the thread_info structure embedded in its task struct.
Therefore its not possible to implement current_thread_info()
by looking at the stack pointer and do some simple calculations
like most other architectures do it.
To return the thread_info pointer for a task two defines are
used. This works until the spinlock function bodies get moved
into an own header file and CONFIG_SPINLOCK_DEBUG is turned on.
That results into this compile error:
In file included from include/linux/spinlock.h:378,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:54,
from arch/m68k/kernel/asm-offsets.c:12:
include/linux/spinlock_api_smp.h: In function '__spin_unlock_irq':
include/linux/spinlock_api_smp.h:371: error: 'current' undeclared (first use in this function)
include/linux/spinlock_api_smp.h:371: error: (Each undeclared identifier is reported only once
include/linux/spinlock_api_smp.h:371: error: for each function it appears in.)
Including asm/current.h to asm-offsets.c wouldn't help since
the definition of struct task is needed. So we end up with ugly
header file include dependencies.
To solve this calculate the offset of the thread_info structure
into the task struct in asm-offsets.h and use the offset in
task_thread_info(). This works just like it does for IA64 as
well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Horst Hartmann <horsth@linux.vnet.ibm.com>
Cc: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <20090831124417.329662275@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to be able to use asm-offsets.h in C files the
existing namespace conflicts must be solved first. In
asm-offsets.h e.g. PT_D0 gets defined which is the offset of
the d0 member of the pt_regs structure. However a same define
(with a different meaning) exists in asm/ptregs.h.
So rename the defines created with the asm-offset mechanism to
PT_OFF_D0 etc. There also already exist a few defines with
these names that have the same meaning. So remove the existing
defines and use the asm-offset generated ones.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Horst Hartmann <horsth@linux.vnet.ibm.com>
Cc: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <20090831124416.666403991@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/m68k/include/asm/pgtable_mm.h:148:1: warning: "pgprot_noncached" redefined
In file included from arch/m68k/include/asm/pgtable_mm.h:138,
from arch/m68k/include/asm/pgtable.h:4,
from include/linux/mm.h:40,
from include/linux/pagemap.h:7,
from include/linux/blkdev.h:12,
from arch/m68k/emu/nfblock.c:17:
include/asm-generic/pgtable.h:133:1: warning: this is the location of the previous definition
pgprot_noncached() should be defined _before_ including asm-generic/pgtable.h
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
arch/m68k/include/asm/motorola_pgalloc.h: In function 'pte_alloc_one':
arch/m68k/include/asm/motorola_pgalloc.h:44: warning: passing argument 1 of 'kunmap' from incompatible pointer type
Also, remove unneeded test for kmap() failure.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This sockopt goes in line with SO_TYPE and SO_PROTOCOL. It makes it
possible for userspace programs to pass around file descriptors — I
am referring to arguments-to-functions, but it may even work for the
fd passing over UNIX sockets — without needing to also pass the
auxiliary information (PF_INET6/IPPROTO_TCP).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to SO_TYPE returning the socket type, SO_PROTOCOL allows to
retrieve the protocol used with a given socket.
I am not quite sure why we have that-many copies of socket.h, and why
the values are not the same on all arches either, but for where hex
numbers dominate, I use 0x1029 for SO_PROTOCOL as that seems to be
the next free unused number across a bunch of operating systems, or
so Google results make me want to believe. SO_PROTOCOL for others
just uses the next free Linux number, 38.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert most arches to use asm-generic/kmap_types.h.
Move the KM_FENCE_ macro additions into asm-generic/kmap_types.h,
controlled by __WITH_KM_FENCE from each arch's kmap_types.h file.
Would be nice to be able to add custom KM_types per arch, but I don't yet
see a nice, clean way to do that.
Built on x86_64, i386, mips, sparc, alpha(tonyb), powerpc(tonyb), and
68k(tonyb).
Note: avr32 should be able to remove KM_PTE2 (since it's not used) and
then just use the generic kmap_types.h file. Get avr32 maintainer
approval.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused asm/suspend.h files for
the following architectures:
alpha, arm, ia64, m68k, mips, s390, um
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current asm-generic/page.h only contains the get_order
function, and asm-generic/uaccess.h only implements
unaligned accesses. This renames the file to getorder.h
and uaccess-unaligned.h to make room for new page.h
and uaccess.h file that will be usable by all simple
(e.g. nommu) architectures.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic/atomic.h only defines the
atomic_long type. This renames it to atomic-long.h
so we have a place to add a truly generic atomic.h
that can be used on all non-SMP systems.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
This provides a reliable way for asm-generic/types.h and other
files to find out if it is running on a 32 or 64 bit platform.
We cannot use CONFIG_64BIT for this in headers that are included
from user space because CONFIG symbols are not available there.
We also cannot do it inside of asm/types.h because some headers
need the word size but cannot include types.h.
The solution is to introduce a new header <asm/bitsperlong.h>
that defines both __BITS_PER_LONG for user space and
BITS_PER_LONG for usage in the kernel. The asm-generic
version falls back to 32 bit unless the architecture overrides
it, which I did for all 64 bit platforms.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic versions are incomplete and included
by some architectures. New architectures should be able
to use a generic version, so rename the existing files and
change all users, which lets us add the new files.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use proper field value setting init INIT_THREAD macro.
Fixes this:
arch/m68knommu/kernel/init_task.c:27: warning: excess elements in array initializer
arch/m68knommu/kernel/init_task.c:27: warning: (near initialization for ‘init_task.thread.fpstate’)
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
fix the following 'make headers_check' warnings:
usr/include/asm-m68k/swab.h:4: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-m68k/swab.h:10: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All ColdFire and non-MMU 68k code has custom reset routines.
Remove the obsolete and now un-used reset macros.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The sofwtare reset control code for the 523x ColdFire family uses the
same Reset unit hardware as the 527x and 528x ColdFire parts. So they
should all use the same code. Merge them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The sofwtare reset control for the 527x ColdFire family is based on
the same Reset Control Unit as the 528x ColdFire family. So use the
same reset code for both.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The flat loader uses an architecture's flat_stack_align() to align the
stack but assumes word-alignment is enough for the data sections.
However, on the Xtensa S6000 we have registers up to 128bit width
which can be used from userspace and therefor need userspace stack and
data-section alignment of at least this size.
This patch drops flat_stack_align() and uses the same alignment that
is required for slab caches, ARCH_SLAB_MINALIGN, or wordsize if it's
not defined by the architecture.
It also fixes m32r which was obviously kaput, aligning an
uninitialized stack entry instead of the stack pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (41 commits)
m68knommu: improve compile arch switch settings
m68knommu: fix 5407 ColdFire UART vector setup
m68knommu: fix 5307 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART vector setup
m68knommu: fix 5249 ColdFire UART setup
m68knommu: fix end of uart table marker
m68knommu: switch to using generic_handle_irq()
m68k: merge the mmu and non-mmu versions of tlbflush.h
m68knommu: introduce basic clk infrastructure
m68k: merge the mmu and non-mmu versions of module.h
m68knommu: add missing interrupt line definition for UART 2
m68k: merge the mmu and non-mmu versions of mmu_context.h
m68k: merge the mmu and non-mmu versions of current.h
m68k: merge the mmu and non-mmu versions of div64.h
m68k: merge the mmu and non-mmu versions of bugs.h
m68k: merge the mmu and non-mmu versions of bug.h
m68k: use the mmu version of cache.h for m68knommu as well
m68k: use the mmu version of bootinfo.h for m68knommu as well
m68k: merge the mmu and non-mmu versions of fb.h
m68k: merge the mmu and non-mmu versions of segment.h
...
m68k has been a long time user of the generic RTC abstraction, so hook up
rtc-generic:
- Create the "rtc-generic" platform device if mach_hwclk is set,
- Add checks for mach_hwclk, in anticipation of RTC chip drivers being moved
to drivers/rtc/.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
* Remove superfluous <asm/macints.h> include.
* No need to re-define in/out*() macros as they are no longer used
by m68k host drivers.
* readl() and writel() are not used by core IDE code.
* Use raw_*_swapw() directly in {falcon,q40}ide.c and remove
{in,out}sw_swapw() macros.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->{get,release}_lock methods to struct ide_port_info
and struct ide_host.
* Convert core IDE code, m68k IDE code and falconide support to use
->{get,release}_lock methods instead of ide_{get,release}_lock().
* Remove IDE_ARCH_LOCK.
v2:
* Build fix from Geert updating ide_{get,release}_lock() callers in
falconide.c.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Michael Schmitz
Arun Sharma
Andrew Morton
Mike Frysinger
Linus Torvalds
Mathias Krause
Geert Uytterhoeven
Greg Ungerer
Eric W. Biederman
Akinobu Mita
Michael Schmitz
Jiri Kosina
Justin P. Mattock
Lucas De Marchi
FUJITA Tomonori
Petr Stehlik
Roman Zippel
Philippe De Muyter
Al Viro
Peter Zijlstra
Thorsten Glaser
Greg Ungerer
Christian Dietrich
Jeff Mahoney
David Howells
Jate Sujjavanich
hyc@symas.com
Robert P. J. Day
Anton Blanchard
Steven King
Andreas Dilger
Maxim Kuvyrkov
Christoph Hellwig
Finn Thain
Russell King
Daniel Mack
Sam Ravnborg
Tejun Heo
Tim Abbott
Andreas Schwab
André Goddard Rosa
Ilya Loginov
Neil Horman
Arnd Bergmann
Ingo Molnar
Heiko Carstens
Alexey Dobriyan
David S. Miller
Jan Engelhardt
Benjamin Herrenschmidt
Randy Dunlap
Magnus Damm
Jaswinder Singh Rajput
Oskar Schirmer
Geert Uytterhoeven
Bartlomiej Zolnierkiewicz