The md code stores the exact time of the last error in the
last_read_error variable using a timespec structure. It only
ever uses the seconds portion of that though, so we can
use a scalar for it.
There won't be an overflow in 2038 here, because it already
used monotonic time and 32-bit is enough for that, but I've
decided to use time64_t for consistency in the conversion.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Every time a device is removed with ->hot_remove_disk() a synchronize_rcu() call is made
which can delay several milliseconds in some case.
If lots of devices fail at once - as could happen with a large RAID10 where one set
of devices are removed all at once - these delays can add up to be very inconcenient.
As failure is not reversible we can check for that first, setting a
separate flag if it is found, and then all synchronize_rcu() once for
all the flagged devices. Then ->hot_remove_disk() function can skip the
synchronize_rcu() step if the flag is set.
fix build error(Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have md
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add a disk to an array which is performing recovery
is a little complicated, we need to do both reap the
sync thread and perform add disk for the case, then
it caused deadlock as follows.
linux44:~ # ps aux|grep md|grep D
root 1822 0.0 0.0 0 0 ? D 16:50 0:00 [md127_resync]
root 1848 0.0 0.0 19860 952 pts/0 D+ 16:50 0:00 mdadm --manage /dev/md127 --re-add /dev/vdb
linux44:~ # cat /proc/1848/stack
[<ffffffff8107afde>] kthread_stop+0x6e/0x120
[<ffffffffa051ddb0>] md_unregister_thread+0x40/0x80 [md_mod]
[<ffffffffa0526e45>] md_reap_sync_thread+0x15/0x150 [md_mod]
[<ffffffffa05271e0>] action_store+0x260/0x270 [md_mod]
[<ffffffffa05206b4>] md_attr_store+0xb4/0x100 [md_mod]
[<ffffffff81214a7e>] sysfs_write_file+0xbe/0x140
[<ffffffff811a6b98>] vfs_write+0xb8/0x1e0
[<ffffffff811a75b8>] SyS_write+0x48/0xa0
[<ffffffff8152a5c9>] system_call_fastpath+0x16/0x1b
[<00007f068ea1ed30>] 0x7f068ea1ed30
linux44:~ # cat /proc/1822/stack
[<ffffffffa05251a6>] md_do_sync+0x846/0xf40 [md_mod]
[<ffffffffa052402d>] md_thread+0x16d/0x180 [md_mod]
[<ffffffff8107ad94>] kthread+0xb4/0xc0
[<ffffffff8152a518>] ret_from_fork+0x58/0x90
Task1848 Task1822
md_attr_store (held reconfig_mutex by call mddev_lock())
action_store
md_reap_sync_thread
md_unregister_thread
kthread_stop md_wakeup_thread(mddev->thread);
wait_event(mddev->sb_wait, !test_bit(MD_CHANGE_PENDING))
md_check_recovery is triggered by wakeup mddev->thread,
but it can't clear MD_CHANGE_PENDING flag since it can't
get lock which was held by md_attr_store already.
To solve the deadlock problem, we move "->resync_finish()"
from md_do_sync to md_reap_sync_thread (after md_update_sb),
also MD_HELD_RESYNC_LOCK is introduced since it is possible
that node can't get resync lock in md_do_sync.
Then we do not need to wait for MD_CHANGE_PENDING is cleared
or not since metadata should be updated after md_update_sb,
so just call resync_finish if MD_HELD_RESYNC_LOCK is set.
We also unified the code after skip label, since set PENDING
for non-clustered case should be harmless.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Mostly clustered-raid1 and raid5 journal updates.
one Y2038 fix and other minor stuff.
One patch removes me from the MAINTAINERS file and adds a record of
my md maintainership to Credits.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gl+r
-----END PGP SIGNATURE-----
Merge tag 'md/4.5' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"Mostly clustered-raid1 and raid5 journal updates. one Y2038 fix and
other minor stuff.
One patch removes me from the MAINTAINERS file and adds a record of my
md maintainership to Credits"
Many thanks to Neil, who has been around for a _looong_ time.
* tag 'md/4.5' of git://neil.brown.name/md: (26 commits)
md/raid: only permit hot-add of compatible integrity profiles
Remove myself as MD Maintainer, and add to Credits.
raid5-cache: handle journal hotadd in quiesce
MD: add journal with array suspended
md: set MD_HAS_JOURNAL in correct places
md: Remove 'ready' field from mddev.
md: remove unnecesary md_new_event_inintr
raid5: allow r5l_io_unit allocations to fail
raid5-cache: use a mempool for the metadata block
raid5-cache: use a bio_set
raid5-cache: add journal hot add/remove support
drivers: md: use ktime_get_real_seconds()
md: avoid warning for 32-bit sector_t
raid5-cache: free meta_page earlier
raid5-cache: simplify r5l_move_io_unit_list
md: update comment for md_allow_write
md-cluster: update comments for MD_CLUSTER_SEND_LOCKED_ALREADY
md-cluster: Protect communication with mutexes
md-cluster: Defer MD reloading to mddev->thread
md-cluster: update the documentation
...
1/ Media error handling: The 'badblocks' implementation that originated
in md-raid is up-levelled to a generic capability of a block device.
This initial implementation is limited to being consulted in the pmem
block-i/o path. Later, 'badblocks' will be consulted when creating
dax mappings.
2/ Raw block device dax: For virtualization and other cases that want
large contiguous mappings of persistent memory, add the capability to
dax-mmap a block device directly.
3/ Increased /dev/mem restrictions: Add an option to treat all io-memory
as IORESOURCE_EXCLUSIVE, i.e. disable /dev/mem access while a driver is
actively using an address range. This behavior is controlled via the
new CONFIG_IO_STRICT_DEVMEM option and can be overridden by the
existing "iomem=relaxed" kernel command line option.
4/ Miscellaneous fixes include a 'pfn'-device huge page alignment fix,
block device shutdown crash fix, and other small libnvdimm fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7V5r
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has appeared in -next and independently received a
build success notification from the kbuild robot. The 'for-4.5/block-
dax' topic branch was rebased over the weekend to drop the "block
device end-of-life" rework that Al would like to see re-implemented
with a notifier, and to address bug reports against the badblocks
integration.
There is pending feedback against "libnvdimm: Add a poison list and
export badblocks" received last week. Linda identified some localized
fixups that we will handle incrementally.
Summary:
- Media error handling: The 'badblocks' implementation that
originated in md-raid is up-levelled to a generic capability of a
block device. This initial implementation is limited to being
consulted in the pmem block-i/o path. Later, 'badblocks' will be
consulted when creating dax mappings.
- Raw block device dax: For virtualization and other cases that want
large contiguous mappings of persistent memory, add the capability
to dax-mmap a block device directly.
- Increased /dev/mem restrictions: Add an option to treat all
io-memory as IORESOURCE_EXCLUSIVE, i.e. disable /dev/mem access
while a driver is actively using an address range. This behavior
is controlled via the new CONFIG_IO_STRICT_DEVMEM option and can be
overridden by the existing "iomem=relaxed" kernel command line
option.
- Miscellaneous fixes include a 'pfn'-device huge page alignment fix,
block device shutdown crash fix, and other small libnvdimm fixes"
* tag 'libnvdimm-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (32 commits)
block: kill disk_{check|set|clear|alloc}_badblocks
libnvdimm, pmem: nvdimm_read_bytes() badblocks support
pmem, dax: disable dax in the presence of bad blocks
pmem: fail io-requests to known bad blocks
libnvdimm: convert to statically allocated badblocks
libnvdimm: don't fail init for full badblocks list
block, badblocks: introduce devm_init_badblocks
block: clarify badblocks lifetime
badblocks: rename badblocks_free to badblocks_exit
libnvdimm, pmem: move definition of nvdimm_namespace_add_poison to nd.h
libnvdimm: Add a poison list and export badblocks
nfit_test: Enable DSMs for all test NFITs
md: convert to use the generic badblocks code
block: Add badblock management for gendisks
badblocks: Add core badblock management code
block: fix del_gendisk() vs blkdev_ioctl crash
block: enable dax for raw block devices
block: introduce bdev_file_inode()
restrict /dev/mem to idle io memory ranges
arch: consolidate CONFIG_STRICT_DEVM in lib/Kconfig.debug
...
It is not safe for an integrity profile to be changed while i/o is
in-flight in the queue. Prevent adding new disks or otherwise online
spares to an array if the device has an incompatible integrity profile.
The original change to the blk_integrity_unregister implementation in
md, commmit c7bfced9a6 "md: suspend i/o during runtime
blk_integrity_unregister" introduced an immediate hang regression.
This policy of disallowing changes the integrity profile once one has
been established is shared with DM.
Here is an abbreviated log from a test run that:
1/ Creates a degraded raid1 with an integrity-enabled device (pmem0s) [ 59.076127]
2/ Tries to add an integrity-disabled device (pmem1m) [ 90.489209]
3/ Retries with an integrity-enabled device (pmem1s) [ 205.671277]
[ 59.076127] md/raid1:md0: active with 1 out of 2 mirrors
[ 59.078302] md: data integrity enabled on md0
[..]
[ 90.489209] md0: incompatible integrity profile for pmem1m
[..]
[ 205.671277] md: super_written gets error=-5
[ 205.677386] md/raid1:md0: Disk failure on pmem1m, disabling device.
[ 205.677386] md/raid1:md0: Operation continuing on 1 devices.
[ 205.683037] RAID1 conf printout:
[ 205.684699] --- wd:1 rd:2
[ 205.685972] disk 0, wo:0, o:1, dev:pmem0s
[ 205.687562] disk 1, wo:1, o:1, dev:pmem1s
[ 205.691717] md: recovery of RAID array md0
Fixes: c7bfced9a6 ("md: suspend i/o during runtime blk_integrity_unregister")
Cc: <stable@vger.kernel.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Reported-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Retain badblocks as part of rdev, but use the accessor functions from
include/linux/badblocks for all manipulation.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This field is always set in tandem with ->pers, and when it is tested
->pers is also tested. So ->ready is not needed.
It was needed once, but code rearrangement and locking changes have
removed that needed.
Signed-off-by: NeilBrown <neilb@suse.com>
get_seconds() API is not y2038 safe on 32 bit systems and the API
is deprecated. Replace it with calls to ktime_get_real_seconds()
API instead. Change mddev structure types to time64_t accordingly.
32 bit signed timestamps will overflow in the year 2038.
Change the user interface mdu_array_info_s structure timestamps:
ctime and utime values used in ioctls GET_ARRAY_INFO and
SET_ARRAY_INFO to unsigned int. This will extend the field to last
until the year 2106.
The long term plan is to get rid of ctime and utime values in
this structure as this information can be read from the on-disk
meta data directly.
Clamp the tim64_t timestamps to positive values with a max of U32_MAX
when returning from GET_ARRAY_INFO ioctl to accommodate above changes
in the data type of timestamps to unsigned int.
v0.90 on disk meta data uses u32 for maintaining time stamps.
So this will also last until year 2106.
Assumption is that the usage of v0.90 will be deprecated by
year 2106.
Timestamp fields in the on disk meta data for v1.0 version already
use 64 bit data types. Remove the truncation of the bits while
writing to or reading from these from the disk.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NeilBrown <neilb@suse.com>
Reloading of superblock must be performed under reconfig_mutex. However,
this cannot be done with md_reload_sb because it would deadlock with
the message DLM lock. So, we defer it in md_check_recovery() which is
executed by mddev->thread.
This introduces a new flag, MD_RELOAD_SB, which if set, will reload the
superblock. And good_device_nr is also added to 'struct mddev' which is
used to get the num of the good device within cluster raid.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
For cluster raid, if one disk couldn't be reach in one node, then
other nodes would receive the REMOVE message for the disk.
In receiving node, we can't call md_kick_rdev_from_array to remove
the disk from array synchronously since the disk might still be busy
in this node. So let's set a ClusterRemove flag on the disk, then
let the thread to do the removal job eventually.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Neil pointed out setting journal disk role to raid_disks will confuse
reshape if we support reshape eventually. Switching the role to 0 (we
should be fine as long as the value >=0) and skip sysfs file creation to
avoid error.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
If a raid array has journal feature bit set, add a new bit to indicate
this. If the array is started without journal disk existing, we know
there is something wrong.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
If a raid array has journal, the journal can guarantee the consistency,
we can skip resync after a unclean shutdown. The exception is raid
creation or user initiated resync, which we still do a raid resync.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Journal device stores data in a log structure. We need record the log
start. Here we override md superblock recovery_offset for this purpose.
This field of a journal device is meaningless otherwise.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Next patches will use a disk as raid5/6 journaling. We need a new disk
role to present the journal device and add MD_FEATURE_JOURNAL to
feature_map for backward compability.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
md_reload_sb is too simplistic and it explicitly needs to determine
the changes made by the writing node. However, there are multiple areas
where a simple reload could fail.
Instead, read the superblock of one of the "good" rdevs and update
the necessary information:
- read the superblock into a newly allocated page, by temporarily
swapping out rdev->sb_page and calling ->load_super.
- if that fails return
- if it succeeds, call check_sb_changes
1. iterates over list of active devices and checks the matching
dev_roles[] value.
If that is 'faulty', the device must be marked as faulty
- call md_error to mark the device as faulty. Make sure
not to set CHANGE_DEVS and wakeup mddev->thread or else
it would initiate a resync process, which is the responsibility
of the "primary" node.
- clear the Blocked bit
- Call remove_and_add_spares() to hot remove the device.
If the device is 'spare':
- call remove_and_add_spares() to get the number of spares
added in this operation.
- Reduce mddev->degraded to mark the array as not degraded.
2. reset recovery_cp
- read the rest of the rdevs to update recovery_offset. If recovery_offset
is equal to MaxSector, call spare_active() to set it In_sync
This required that recovery_offset be initialized to MaxSector, as
opposed to zero so as to communicate the end of sync for a rdev.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
With the planned cgroup writeback support, backing-dev related
declarations will be more widely used across block and cgroup;
unfortunately, including backing-dev.h from include/linux/blkdev.h
makes cyclic include dependency quite likely.
This patch separates out backing-dev-defs.h which only has the
essential definitions and updates blkdev.h to include it. c files
which need access to more backing-dev details now include
backing-dev.h directly. This takes backing-dev.h off the common
include dependency chain making it a lot easier to use it across block
and cgroup.
v2: fs/fat build failure fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
This option is not well justified and testing suggests that
it hardly ever makes any difference.
The comment suggests there might be a need to wait for non-resync
activity indicated by ->nr_waiting, however raise_barrier()
already waits for all of that.
So just remove it to simplify reasoning about speed limiting.
This allows us to remove a 'FIXME' comment from raid5.c as that
never used the flag.
Signed-off-by: NeilBrown <neilb@suse.de>
This is required by the clustering module (patches to follow) to
find the device to remove or re-add.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This export is required for clustering module in order to
co-ordinate remove/readd a rdev from all nodes.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Algorithm:
1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues
ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD)
2. Node 1 sends NEWDISK with uuid and slot number
3. Other nodes issue kobject_uevent_env with uuid and slot number
(Steps 4,5 could be a udev rule)
4. In userspace, the node searches for the disk, perhaps
using blkid -t SUB_UUID=""
5. Other nodes issue either of the following depending on whether the disk
was found:
ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and
disc.number set to slot number)
ioctl(CLUSTERED_DISK_NACK)
6. Other nodes drop lock on no-new-devs (CR) if device is found
7. Node 1 attempts EX lock on no-new-devs
8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk
as SpareLocal
9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED
10. Other nodes understand if the device is added or not by reading the superblock again after receiving the METADATA_UPDATED message.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Re-reads the devices by invalidating the cache.
Since we don't write to faulty devices, this is detected using
events recorded in the devices. If it is old as compared to the mddev
mark it is faulty.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
DLM offers callbacks when a node fails and the lock remastery
is performed:
1. recover_prep: called when DLM discovers a node is down
2. recover_slot: called when DLM identifies the node and recovery
can start
3. recover_done: called when all nodes have completed recover_slot
recover_slot() and recover_done() are also called when the node joins
initially in order to inform the node with its slot number. These slot
numbers start from one, so we deduct one to make it start with zero
which the cluster-md code uses.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
md_cluster_info stores the cluster information in the MD device.
The join() is called when mddev detects it is a clustered device.
The main responsibilities are:
1. Setup a DLM lockspace
2. Setup all initial locks such as super block locks and bitmap lock (will come later)
The leave() clears up the lockspace and all the locks held.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
After each call to rdev_dec_pending() we should wakeup the
md thread if the device is found to be faulty.
Otherwise we'll incur heavy delays on failing devices.
Signed-off-by: Neil Brown <nfbrown@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
The one which is not inline (mddev_unlock) gets EXPORTed.
This makes the locking available to personality modules so that it
doesn't have to be imposed upon them.
Signed-off-by: NeilBrown <neilb@suse.de>
There are interdependencies between these two sysfs attributes
and whether a resync is currently running.
Rather than depending on reconfig_mutex to ensure no races when
testing these interdependencies are met, use the spinlock.
This will allow the mutex to be remove from protecting this
code in a subsequent patch.
Signed-off-by: NeilBrown <neilb@suse.de>
It makes more sense to report bitmap_info->file, rather than
bitmap->file (the later is only available once the array is
active).
With that change, use mddev->lock to protect bitmap_info being
set to NULL, and we can call get_bitmap_file() without taking
the mutex.
Signed-off-by: NeilBrown <neilb@suse.de>
->pers is already protected by ->reconfig_mutex, and
cannot possibly change when there are threads running or
outstanding IO.
However there are some places where we access ->pers
not in a thread or IO context, and where ->reconfig_mutex
is unnecessarily heavy-weight: level_show and md_seq_show().
So protect all changes, and those accesses, with ->lock.
This is a step toward taking those accesses out from under
reconfig_mutex.
[Fixed missing "mddev->pers" -> "pers" conversion, thanks to
Dan Carpenter <dan.carpenter@oracle.com>]
Signed-off-by: NeilBrown <neilb@suse.de>
Now that the ->stop function only frees the private data,
rename is accordingly.
Also pass in the private pointer as an arg rather than using
mddev->private. This flexibility will be useful in level_store().
Finally, don't clear ->private. It doesn't make sense to clear
it seeing that isn't what we free, and it is no longer necessary
to clear ->private (it was some time ago before ->to_remove was
introduced).
Setting ->to_remove in ->free() is a bit of a wart, but not a
big problem at the moment.
Signed-off-by: NeilBrown <neilb@suse.de>
There is no locking around calls to merge_bvec_fn(), so
it is possible that calls which coincide with a level (or personality)
change could go wrong.
So create a central dispatch point for these functions and use
rcu_read_lock().
If the array is suspended, reject any merge that can be rejected.
If not, we know it is safe to call the function.
Signed-off-by: NeilBrown <neilb@suse.de>
There is currently no locking around calls to the 'congested'
bdi function. If called at an awkward time while an array is
being converted from one level (or personality) to another, there
is a tiny chance of running code in an unreferenced module etc.
So add a 'congested' function to the md_personality operations
structure, and call it with appropriate locking from a central
'mddev_congested'.
When the array personality is changing the array will be 'suspended'
so no IO is processed.
If mddev_congested detects this, it simply reports that the
array is congested, which is a safe guess.
As mddev_suspend calls synchronize_rcu(), mddev_congested can
avoid races by included the whole call inside an rcu_read_lock()
region.
This require that the congested functions for all subordinate devices
can be run under rcu_lock. Fortunately this is the case.
Signed-off-by: NeilBrown <neilb@suse.de>
This lock is used for (slightly) more than helping with writing
superblocks, and it will soon be extended further. So the
name is inappropriate.
Also, the _irq variant hasn't been needed since 2.6.37 as it is
never taking from interrupt or bh context.
So:
-rename write_lock to lock
-document what it protects
-remove _irq ... except in md_flush_request() as there
is no wait_event_lock() (with no _irq). This can be
cleaned up after appropriate changes to wait.h.
Signed-off-by: NeilBrown <neilb@suse.de>
md bitmap code currently tries to use i_writecount to stop any other
process from writing to out bitmap file. But that is really an abuse
and has bit-rotted so locking is all wrong.
So discard that - root should be allowed to shoot self in foot.
Still use it in a much less intrusive way to stop the same file being
used as bitmap on two different array, and apply other checks to
ensure the file is at least vaguely usable for bitmap storage
(is regular, is open for write. Support for ->bmap is already checked
elsewhere).
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NeilBrown <neilb@suse.de>
Here's the big driver core and sysfs patch set for 3.14-rc1.
There's a lot of work here moving sysfs logic out into a "kernfs" to
allow other subsystems to also have a virtual filesystem with the same
attributes of sysfs (handle device disconnect, dynamic creation /
removal as needed / unneeded, etc. This is primarily being done for
the cgroups filesystem, but the goal is to also move debugfs to it when
it is ready, solving all of the known issues in that filesystem as well.
The code isn't completed yet, but all should be stable now (there is a
big section that was reverted due to problems found when testing.)
There's also some other smaller fixes, and a driver core addition that
allows for a "collection" of objects, that the DRM people will be using
soon (it's in this tree to make merges after -rc1 easier.)
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdh0cACgkQMUfUDdst+ylv4QCfeDKDgLo4LsaBIIrFSxLoH/c7
UUsAoMPRwA0h8wy+BQcJAg4H4J4maKj3
=0pc0
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core and sysfs patch set for 3.14-rc1.
There's a lot of work here moving sysfs logic out into a "kernfs" to
allow other subsystems to also have a virtual filesystem with the same
attributes of sysfs (handle device disconnect, dynamic creation /
removal as needed / unneeded, etc)
This is primarily being done for the cgroups filesystem, but the goal
is to also move debugfs to it when it is ready, solving all of the
known issues in that filesystem as well. The code isn't completed
yet, but all should be stable now (there is a big section that was
reverted due to problems found when testing)
There's also some other smaller fixes, and a driver core addition that
allows for a "collection" of objects, that the DRM people will be
using soon (it's in this tree to make merges after -rc1 easier)
All of this has been in linux-next with no reported issues"
* tag 'driver-core-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (113 commits)
kernfs: associate a new kernfs_node with its parent on creation
kernfs: add struct dentry declaration in kernfs.h
kernfs: fix get_active failure handling in kernfs_seq_*()
Revert "kernfs: fix get_active failure handling in kernfs_seq_*()"
Revert "kernfs: replace kernfs_node->u.completion with kernfs_root->deactivate_waitq"
Revert "kernfs: remove KERNFS_ACTIVE_REF and add kernfs_lockdep()"
Revert "kernfs: remove KERNFS_REMOVED"
Revert "kernfs: restructure removal path to fix possible premature return"
Revert "kernfs: invoke kernfs_unmap_bin_file() directly from __kernfs_remove()"
Revert "kernfs: remove kernfs_addrm_cxt"
Revert "kernfs: make kernfs_get_active() block if the node is deactivated but not removed"
Revert "kernfs: implement kernfs_{de|re}activate[_self]()"
Revert "kernfs, sysfs, driver-core: implement kernfs_remove_self() and its wrappers"
Revert "pci: use device_remove_file_self() instead of device_schedule_callback()"
Revert "scsi: use device_remove_file_self() instead of device_schedule_callback()"
Revert "s390: use device_remove_file_self() instead of device_schedule_callback()"
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
Revert "kernfs: remove unnecessary NULL check in __kernfs_remove()"
kernfs: remove unnecessary NULL check in __kernfs_remove()
drivers/base: provide an infrastructure for componentised subsystems
...
If an array is started degraded, and then the missing device
is found it can be re-added and a minimal bitmap-based recovery
will bring it fully up-to-date.
If the array is read-only a recovery would not be allowed.
But also if the array is read-only and the missing device was
present very recently, then there could be no need for any
recovery at all, so we simply include the device in the read-only
array without any recovery.
However... if the missing device was removed a little longer ago
it could be missing some updates, but if a bitmap is present it will
be conditionally accepted pending a bitmap-based update. We don't
currently detect this case properly and will include that old
device into the read-only array with no recovery even though it really
needs a recovery.
This patch keeps track of whether a bitmap-based-recovery is really
needed or not in the new Bitmap_sync rdev flag. If that is set,
then the device will not be added to a read-only array.
Cc: Andrei Warkentin <andreiw@vmware.com>
Fixes: d70ed2e4fa
Cc: stable@vger.kernel.org (3.2+)
Signed-off-by: NeilBrown <neilb@suse.de>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/sysfs_elem_dir/kernfs_elem_dir/
* s/sysfs_elem_symlink/kernfs_elem_symlink/
* s/sysfs_elem_attr/kernfs_elem_file/
* s/sysfs_dirent/kernfs_node/
* s/sd/kn/ in kernfs proper
* s/parent_sd/parent/
* s/target_sd/target/
* s/dir_sd/parent/
* s/to_sysfs_dirent()/rb_to_kn()/
* misc renames of local vars when they conflict with the above
Because md, mic and gpio dig into sysfs details, this patch ends up
modifying them. All are sysfs_dirent renames and trivial. While we
can avoid these by introducing a dummy wrapping struct sysfs_dirent
around kernfs_node, given the limited usage outside kernfs and sysfs
proper, I don't think such workaround is called for.
This patch is strictly rename only and doesn't introduce any
functional difference.
- mic / gpio renames were missing. Spotted by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull block IO core updates from Jens Axboe:
"This is the pull request for the core changes in the block layer for
3.13. It contains:
- The new blk-mq request interface.
This is a new and more scalable queueing model that marries the
best part of the request based interface we currently have (which
is fully featured, but scales poorly) and the bio based "interface"
which the new drivers for high IOPS devices end up using because
it's much faster than the request based one.
The bio interface has no block layer support, since it taps into
the stack much earlier. This means that drivers end up having to
implement a lot of functionality on their own, like tagging,
timeout handling, requeue, etc. The blk-mq interface provides all
these. Some drivers even provide a switch to select bio or rq and
has code to handle both, since things like merging only works in
the rq model and hence is faster for some workloads. This is a
huge mess. Conversion of these drivers nets us a substantial code
reduction. Initial results on converting SCSI to this model even
shows an 8x improvement on single queue devices. So while the
model was intended to work on the newer multiqueue devices, it has
substantial improvements for "classic" hardware as well. This code
has gone through extensive testing and development, it's now ready
to go. A pull request is coming to convert virtio-blk to this
model will be will be coming as well, with more drivers scheduled
for 3.14 conversion.
- Two blktrace fixes from Jan and Chen Gang.
- A plug merge fix from Alireza Haghdoost.
- Conversion of __get_cpu_var() from Christoph Lameter.
- Fix for sector_div() with 64-bit divider from Geert Uytterhoeven.
- A fix for a race between request completion and the timeout
handling from Jeff Moyer. This is what caused the merge conflict
with blk-mq/core, in case you are looking at that.
- A dm stacking fix from Mike Snitzer.
- A code consolidation fix and duplicated code removal from Kent
Overstreet.
- A handful of block bug fixes from Mikulas Patocka, fixing a loop
crash and memory corruption on blk cg.
- Elevator switch bug fix from Tomoki Sekiyama.
A heads-up that I had to rebase this branch. Initially the immutable
bio_vecs had been queued up for inclusion, but a week later, it became
clear that it wasn't fully cooked yet. So the decision was made to
pull this out and postpone it until 3.14. It was a straight forward
rebase, just pruning out the immutable series and the later fixes of
problems with it. The rest of the patches applied directly and no
further changes were made"
* 'for-3.13/core' of git://git.kernel.dk/linux-block: (31 commits)
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: Do not call sector_div() with a 64-bit divisor
kernel: trace: blktrace: remove redundent memcpy() in compat_blk_trace_setup()
block: Consolidate duplicated bio_trim() implementations
block: Use rw_copy_check_uvector()
block: Enable sysfs nomerge control for I/O requests in the plug list
block: properly stack underlying max_segment_size to DM device
elevator: acquire q->sysfs_lock in elevator_change()
elevator: Fix a race in elevator switching and md device initialization
block: Replace __get_cpu_var uses
bdi: test bdi_init failure
block: fix a probe argument to blk_register_region
loop: fix crash if blk_alloc_queue fails
blk-core: Fix memory corruption if blkcg_init_queue fails
block: fix race between request completion and timeout handling
blktrace: Send BLK_TN_PROCESS events to all running traces
blk-mq: don't disallow request merges for req->special being set
blk-mq: mq plug list breakage
blk-mq: fix for flush deadlock
...
Someone cut and pasted md's md_trim_bio() into xen-blkfront.c. Come on,
we should know better than this.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The pre-existing sysfs interfaces which take explicit namespace
argument are weird in that they place the optional @ns in front of
@name which is contrary to the established convention. For example,
we end up forcing vast majority of sysfs_get_dirent() users to do
sysfs_get_dirent(parent, NULL, name), which is silly and error-prone
especially as @ns and @name may be interchanged without causing
compilation warning.
This renames sysfs_get_dirent() to sysfs_get_dirent_ns() and swap the
positions of @name and @ns, and sysfs_get_dirent() is now a wrapper
around sysfs_get_dirent_ns(). This makes confusions a lot less
likely.
There are other interfaces which take @ns before @name. They'll be
updated by following patches.
This patch doesn't introduce any functional changes.
v2: EXPORT_SYMBOL_GPL() wasn't updated leading to undefined symbol
error on module builds. Reported by build test robot. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the last process closes /dev/mdX sync_blockdev will be called so
that all buffers get flushed.
So if it is then opened for the STOP_ARRAY ioctl to be sent there will
be nothing to flush.
However if we open /dev/mdX in order to send the STOP_ARRAY ioctl just
moments before some other process which was writing closes their file
descriptor, then there won't be a 'last close' and the buffers might
not get flushed.
So do_md_stop() calls sync_blockdev(). However at this point it is
holding ->reconfig_mutex. So if the array is currently 'clean' then
the writes from sync_blockdev() will not complete until the array
can be marked dirty and that won't happen until some other thread
can get ->reconfig_mutex. So we deadlock.
We need to move the sync_blockdev() call to before we take
->reconfig_mutex.
However then some other thread could open /dev/mdX and write to it
after we call sync_blockdev() and before we actually stop the array.
This can leave dirty data in the page cache which is awkward.
So introduce new flag MD_STILL_CLOSED. Set it before calling
sync_blockdev(), clear it if anyone does open the file, and abort the
STOP_ARRAY attempt if it gets set before we lock against further
opens.
It is still possible to get problems if you open /dev/mdX, write to
it, then issue the STOP_ARRAY ioctl. Just don't do that.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->flags is mostly used to record if an update of the
metadata is needed. Sometimes the whole field is tested
instead of just the important bits. This makes it difficult
to introduce more state bits.
So replace all bare tests of mddev->flags with tests for the bits
that actually need testing.
Signed-off-by: NeilBrown <neilb@suse.de>
Shaohua Li
Arnd Bergmann
NeilBrown
Mike Christie
Guoqing Jiang
Linus Torvalds
Dan Williams
Vishal Verma
Deepa Dinamani
Song Liu
Goldwyn Rodrigues
Kent Overstreet
Tejun Heo
NeilBrown
Goldwyn Rodrigues
Hannes Reinecke
Kent Overstreet