Enable McSPI driver to be built for K3 platforms, to support McSPI on
AM654 SoC of K3 family.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel contains QSPI driver strongly tied to MTD and nor-flash memory.
New spi-mem interface allows usage also other memory types, especially
much larger NAND with SPI interface. This driver works as SPI controller
and is not related to MTD, however can work with NAND-flash or other
peripherals using spi-mem interface.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Piotr Bugalski <bugalski.piotr@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a driver for Macronix SPI controller IP.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Re-arrange existing APIs in probe function to
avoid using goto and remove redundant variables.
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
fixed the nitpicks.
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SoC share one irq number between DSPI controllers.
For example, on the LX2160 board, DSPI0 and DSPI1 share one irq number.
In this case, only one DSPI controller can register successfully,
and others will fail.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS private register restoring in spi-pxa2xx.c: pxa2xx_spi_resume()
was added before there was no any other code restoring them. This was
changed after following commits for previous and current LPSS platforms:
c78b083066 ("ACPI / LPSS: custom power domain for LPSS")
41a3da2b8e ("mfd: intel-lpss: Save register context on suspend")
However there is one caveat: There is no LPSS private register context
save/restore for the Intel Lynxpoint in the Linux kernel code.
I did some debugging on one Lynxpoint based device I have and on it the
LPSS register context is not lost over suspend/resume cycle (s2idle).
Which happens for instance on Intel Braswell. I'm speculating but I guess
either firmware does it or the LPSS is kept always on Lynxpoint.
Given that we haven't needed to implement Lynxpoint LPSS I2C or UART
private register context save/restore over four years time I think we are
safe to remove this LPSS private register restoring during resume here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing support for lsb-first mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware supports 4, 8 and 16bit spi words,
so add the missing support for 4bit words.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register an interrupt handler to fill/empty the
tx and rx fifos rather than busy-looping.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we no longer potentially change spi clock
at runtime we can precompute the rx sample delay
at probe time rather than for each transfer.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver previously checked each transfer if the
requested speed was higher than possible with the
current spi clock rate and raised the clock rate
accordingly.
However, there is no check to see if the spi clock
was actually set that high and no way to dynamically
lower the spi clock rate again.
So it seems any potiential users of this functionality
are better off just setting the spi clock rate at init
using the assigned-clock-rates devicetree property.
Removing this dynamic spi clock rate raising allows
us let the spi framework handle min/max speeds
for us.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to know if we're using dma when setting
up the transfer, so just use a local variable for
that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In almost all cases we already have a pointer to the
spi master structure where we have the driver data.
The only exceptions are the dma callbacks which are
easily fixed by passing them the master and using
spi_master_get_devdata to retrieve the driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi master (aka spi controller) structure already
has two fields for storing the rx and tx dma channels.
Just use them rather than duplicating them in driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just read transfer info directly from the spi device
and transfer structures rather than storing it in
driver data first.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Successful transfers leave the spi disabled, so if
we just make sure to disable the spi on error
there should be no need to disable the spi from
master->unprepare_message.
This also flushes the tx and rx fifos,
so no need to do that manually.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The state field is currently only used to make sure
only the last of the tx and rx dma callbacks issue
an spi_finalize_current_transfer.
Rather than using a spinlock we can get away
with just turning the state field into an atomic_t.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware supports 3 different variants of SPI
and there were some code around it, but nothing
to actually set it to anything but "Motorola SPI".
Just drop that code and always use that mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use C99 designated initializers for dma slave config
structures. This also makes sure uninitialized fields
are zeroed so we don't need an explicit memset.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_enable_chip function takes a boolean
argument. Change the type to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
when xfer_len is greater than 64 bytes and use fifo mode
to transfer, the actual length from the third time is mata->xfer_len
but not len in mtk_spi_interrupt().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ARM-based 63xx DSL platforms have the spi-bcm63xx-hsspi controller
present, allow using this driver there as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to use McSPI controller as SPI slave. In slave mode, DMA TX
completion does not mean entire data has been shifted out as data might
still be stuck in FIFO waiting for master to clock the bus. Therefore,
add an IRQ handler for slave mode to know when entire data in FIFO has
been shifted out.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
McSPI has 32 byte FIFO in Transmit-Receive mode. Current code tries to
configuration FIFO watermark level for DMA trigger to be GCD of transfer
length and max FIFO size which would mean trigger level may be set to 32
for transmit-receive mode if length is aligned. This does not work in
case of SPI slave mode where FIFO always needs to have data ready
whenever master starts the clock. With DMA trigger size of 32 there will
be a small window during slave TX where DMA is still putting data into
FIFO but master would have started clock for next byte, resulting in
shifting out of stale data. Similarly, on Slave RX side there may be RX
FIFO overflow
Fix this by setting FIFO watermark for DMA trigger to word
length. This means DMA is triggered as soon as FIFO has space for word
length bytes and DMA would make sure FIFO is almost always full
therefore improving FIFO occupancy in both master and slave mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use standard readl_poll_timeout() macro for polling on status bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The qspi controller is a specialized communication interface
targeting single, dual or quad SPI Flash memories (NOR/NAND).
It can operate in any of the following modes:
-indirect mode: all the operations are performed using the quadspi
registers
-read memory-mapped mode: the external Flash memory is mapped to the
microcontroller address space and is seen by the system as if it was
an internal memory
tested on:
-NOR: mx66l51235l
-NAND: MT29F2G01ABAGD
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA API does its own zone decisions based on the coherent_dma_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
platform_get_irq() can return -EPROBE_DEFER. However, the driver overrides
an error returned by that function with -ENOENT which breaks the deferred
probing. Propagate upstream an error code returned by platform_get_irq()
and remove the bogus "platform" from the error message, while at it...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use PIO mode instead if size is smaller than fifo size, since
dma may be less efficient.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct wml as the last rx sg length instead of the whole transfer
length. Otherwise, mtd_stresstest will be failed as below:
insmod mtd_stresstest.ko dev=0
=================================================
mtd_stresstest: MTD device: 0
mtd_stresstest: not NAND flash, assume page size is 512 bytes.
mtd_stresstest: MTD device size 4194304, eraseblock size 65536, page size 512, count of eraseblocks 64, pa0
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_test: mtd_read from 1ff532, size 880
mtd_test: mtd_read from 20c267, size 64998
spi_master spi0: I/O Error in DMA RX
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
mtd_test: error: read failed at 0x20c267
mtd_stresstest: error -110 occurred
=================================================
insmod: ERROR: could not insert module mtd_stresstest.ko: Connection timed out
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI configuration state includes an SPI_NO_CS flag that disables
all CS line manipulation, for applications that want to manage their
own chip selects. However, this flag is ignored by the GPIO CS code
in the SPI framework.
Correct this omission with a trivial patch.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports GENI based SPI Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including SPI. This driver supports SPI
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.
The later change resulted in occasional BSPI timeouts causing a
regression.
For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.
Switching back to 256 B reads fixes that problem and regression.
Fixes: 345309fa7c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.
Fixes: 5f195ee7d8 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e38 ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7a ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this commit the DSPI driver on the BK4 board can be used for SPI
transmission managed from user space (via /dev/spidev0.0).
Example usage/testing:
insmod ./spi-fsl-dspi.ko
./spidev_test -D /dev/spidev0.0 -s 3000000 -v -H -b 8 -p "\xCC\x11\x22\x74"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rewrite switch code block to directly do the expected number
of shifts in each case and have break statements.
Addresses-Coverity-ID: 1056539 ("Missing break in switch")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently, this code does not actually fall through to the next case
because the machine restarts before it has a chance. However, for the
sake of maintenance and readability, we better add the missing break
statement.
Addresses-Coverity-ID: 1437892 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added spi-mem
code. The Tegra fix is relatively large but fairly straightforward and
mechanical, it runs on probe so it's been reasonably well covered in
-next testing.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuOnETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AhkB/9ahKdmxdxu0uuzzvS5qmdGD+98dTaV
M+7+Bq6CJfBz0YTc9dxTiynbJot15vo5mKDZkDaJrgOoLCWWDGWa/DjRif2qS2o9
QxjWlBPzfOhKb81/HMJ+MaIHYDtAxvCu4iZExUZPxZzypX8Q9U3+9a/u0+JnRug2
guQ/4vYdxTGbR/taFsKLzf28DRqQb74KuDRAHaN44UYBxA1begy5gFOc7cEQTRu0
WACGM8jNL2eWWLXDNnQQTfb2t1v7LbbMorazyCn2e5ujamE4+DSaYWJF5axZiaQN
ZcRVATw0SPiQlsQW/G014SSFJT0waybxWLOynWS9MSgjx84/GRYWvxRv
=3ATM
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added
spi-mem code. The Tegra fix is relatively large but fairly
straightforward and mechanical, it runs on probe so it's been
reasonably well covered in -next testing."
* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
spi: spi-mem: Add missing description for data.nbytes field
spi: rspi: Fix interrupted DMA transfers
spi: rspi: Fix invalid SPI use during system suspend
spi: sh-msiof: Fix handling of write value for SISTR register
spi: sh-msiof: Fix invalid SPI use during system suspend
spi: gpio: Fix copy-and-paste error
spi: tegra20-slink: explicitly enable/disable clock
The of_find_spi_device_by_node() helper function is useful for other
modules too. Export the funciton as GPL like all other spi helper
functions and make it available if CONFIG_OF is enabled, because it isn't
related to the CONFIG_OF_DYNAMIC context. Finally add a stub if
CONFIG_OF isn't enabled, so others must not care about it.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On r8a7791/koelsch:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -22
Apparently the logic in spi_mem_check_op() is wrong, rejecting the
spi-mem operation if any buswidth is valid, instead of invalid.
Fixes: 380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The __exit section is left out for built-in drivers, so a
'remove' callback must not be marked as such to avoid breaking when
we unbind a device at runtime. This was pointed out by kbuild:
`sprd_spi_remove' referenced in section `.data' of drivers/spi/spi-sprd.o: defined in discarded section `.exit.text' of drivers/spi/spi-sprd.o
Fixes: e7d973a31c ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is converted implicitly to another:
drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_TO_DEVICE,
^~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/159
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some combinations are simply not valid and should be rejected before
the op is passed to the SPI controller driver.
Add an spi_mem_check_op() helper and use it in spi_mem_exec_op() and
spi_mem_supports_op() to make sure the spi-mem operation is valid.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This remove the check and subsequent return of error for the case when
a SPI device requires SPI_CS_WORD and is also configured to use a GPIO
for the CS line.
Commit a134cc414e86 ("spi: always use software fallback for SPI_CS_WORD
when using cs_gio") handles this case now, so this check is no longer
necessary.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This modifies the condition for using the software fallback
implementation for SPI_CS_WORD when the SPI controller is using a GPIO
for the CS line. When using a GPIO for CS, the hardware implementation
won't work, so we just enable the software fallback globally in this
case.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673
Signed-off-by: Mark Brown <broonie@kernel.org>
If the pll clock needs to be enabled to get its rate, it will also need
to be enabled to provide it. So ensure it is kept enabled through the
lifetime of the device.
Fixes: 0d7412ed1f ("spi/bcm63xx-hspi: Enable the clock before calling clk_get_rate().")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It makes no sense to remove the device on shutdown. And it break things
when the hardware crucial for shutdown (such as the embedded controller)
is attached to the SPI bus.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the SPI_CS_WORD flag to the TI DaVinci SPI
driver. This mode can be used as long as we are using the hardware
chip select and not a GPIO chip select.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGWgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OAqB/99Zk/yjUqw3q8mQ9TcDyurMrllpNYm
n9KshwKOc1wyfHsbPMke+ytCJHmMpNDKbv80Dk5aTNBvbeNN9OZdcqonGfVfulEB
hhZy6X4wN6QwX6HpIeWl52o4V4zLd0skeZOqMod/4RQKQvG7kCVVetKFfzMBxYpP
4B+jVLg/L/lVsbNqXe53A59C0myg/lkCBFL9uWmiUaAScS/eeWmHX/Z+Guf3DTjo
eR0ZoB55HeovL8AsTV0xAwjae+YM6LMElptXLF/+AlaFmW4WmuRGuU2tCXh+SaHU
/VzwLgekzd1hplHc8tX1Nhdr4qJhI6tcpQOu+IelTqZ/Z/JlpIruaJVB
=sMBd
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGesTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LpbB/9eeBHjpAthphCZ1Q87oUtqn0dbhV9j
+djnjM3BgJX+3T3vl6fnOtyD2MPg/sGX8pMePEcVqUSRp+StY5tCO++zbR7maMxs
Czw5GslnJJ9CG6T7xx1ZE1vWAIeWywH7Pw98daFJpQkj17BEhGrrqSbpctJaRdSy
3e5nZvc3mWQ5k4ttmK+C9MTa6XV3ReaHDfJaagXWM7bykV6mDwVh6dyx4QJ7kwht
Ti+MQ+SYZndySXTFoborSss+5zgYIJ5nKr07PvOsNrjlk2p3hoU+y7MuU+RB9zzs
XP9dgZKSoLWbFdCspaC6DtcT1P2HLQRi5kBfdc8xlUCupa6Y2Jt3Hms1
=TFpo
-----END PGP SIGNATURE-----
Merge tag 'spi-cs-word' into spi-4.20
spi: Provide SPI_CS_WORD
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
This adds a default software implementation for the SPI_CS_WORD flag for
controllers that don't have such a feature.
The SPI_CS_WORD flag indicates that the CS line should be toggled
between each word sent, not just between each transfer. The
implementation works by using existing functions to split transfers into
one-word-sized transfers and sets the cs_change bit for each of the
new transfers.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluf2foTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DooB/4/c+c9nX31WeKh5EUFS3WJUQ4quHC+
ZPS0rqliJm0KQxdSCU6ig2+xbobZWAs9T4ZXPlE7PNk6DmqdtATS5jlzbwmoLvdA
PvxsBwz3dRdIGR/BNbDYEZCb0WGtMHO6BR5c//lBCy+ea5oNENi0w0mFnY+AVeUt
ivM55i/nNmV4DReT3rl5mRz/TQgfI9zc11DPpqDnlQML3emYHmJ+hZa8/1g68d8C
lQHLIQMo6hGyOd3p6uPODGt98cDKIuYl9+fcYVzYFScNshwuMsxTDUXpkhv85Frb
QV6LGlikaEQBh9X9BHjzTHMBqbTFVLX/I+jRC/vK2G21862rfOt3R6vh
=rRj7
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise."
* tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-fsl-dspi: fix broken DSPI_EOQ_MODE
spi: Fix double IDR allocation with DT aliases
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_sqi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_setup':
drivers/spi/spi-davinci.c:422:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DaVinci SPI can use either:
- Internal chip selects (inside the SPI host)
- External chip selects (using GPIO)
- External chip selects passed in pdata
The last way of passing external chip selects through
platform data is not used in the kernel. Delete it to make
the code simpler when refactoring GPIO.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Michele Dionisio <michele.dionisio@gmail.com>
Cc: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need that to adjust the len of the 2nd transfer (called data in
spi-mem) if it's too long to fit in a SPI message or SPI transfer.
Fixes: c36ff266dc ("spi: Extend the core to ease integration of SPI memory controllers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for at91-usart in spi mode. The USART IP can be configured
to work in many modes and one of them is SPI.
The driver was tested on sama5d3-xplained and sama5d4-xplained boards with
enc28j60 ethernet controller as slave.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviwed-by: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a logical problem in spi-gpio with host just
assigning a MOSI line and no MISO: this is interpreted
as the host cannot do RX and the host is flagged with
SPI_MASTER_NO_RX.
This is wrong: since GPIO lines can switch direction,
in 3WIRE operation the host will simply reverse the
direction of the GPIO line and start reading from it,
there is even code for doing this in the driver, but
it went unnoticed because it was tested by using a
master with 4 wires but a device using just 3 wires.
Remove the offending flag.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_spi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-pl022.c: In function 'do_polling_transfer':
drivers/spi/spi-pl022.c:1493:20: warning:
variable 'chip' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-dw driver currently only supports 8 or 16 bits per word.
Since the hardware supports 4-16 bits per word, adapt the driver
to also support this.
Tested on socfpga cyclone5 with a 9-bit SPI display.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-gpio.c: In function 'spi_gpio_remove':
drivers/spi/spi-gpio.c:450:33: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:
m25p80 spi0.0: SPI transfer failed: -512
spi_master spi0: failed to transfer one message from queue
However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:
spi_master spi0: receive timeout
qspi_transfer_out_in() returned -110
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.
This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch changes writing to the SISTR register according to the H/W
user's manual.
The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spi_controller_{suspend,resume}() already prints an error message on
failure, so there is no need to repeat this in individual drivers.
Note: spi_master_{suspend,resume}() is an alias for
spi_controller_{suspend,resume}().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes an embarrassing copy-and-paste error in the
errorpath of spi_gpio_request(): we were checking the wrong
struct member for error code right after retrieveing the
sck GPIO.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change increases the source code readability.
Instead of using `spi->child[cs].direct_access.XXX` use `dir_acc->XXX`.
Instead of using `orion_spi->child[cs].direct_access.vaddr` use `vaddr`.
Signed-off-by: Kosta Zertsekel <zertsekel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Define a mask for the IF_SI_OWNER field.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_chipselect':
drivers/spi/spi-davinci.c:211:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unfortunately, the Jaguar2 CPU_SYSTEM_CTRL register set has a different
layout than the Ocelot one. Handle that while keeping most of the code
common.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the SPI controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the dspi_eoq_write function used by the
ColdFire mcf5441x family. The 16 bit cmd part must be re-set at
each data transfer.
Also, now that fifo_size variables are used for eoq_read/write,
a proper fifo size must be set (16 slots for the ColdFire dspi
module version).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI bus number is provided by a DT alias, idr_alloc() is called
twice, leading to:
WARNING: CPU: 1 PID: 1 at drivers/spi/spi.c:2179 spi_register_controller+0x11c/0x5d8
couldn't get idr
Fix this by moving the handling of fixed SPI bus numbers up, before the
DT handling code fills in ctlr->bus_num.
Fixes: 1a4327fbf4 ("spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
This introduces devres helpers and an API to request a lock by name,
then migrates the sprd SPI driver to use these.
-----BEGIN PGP SIGNATURE-----
iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAlt3P8obHGJqb3JuLmFu
ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3FlMYQAMn/GJ6HrmuvamXFVNRc
33iExGw0c2a1WL0LN1Fe/rNkOOApb8+smaf053aqFOfcjhsxOeeFvKOuMrkLzpmL
o7Ls9EFhLUwwRAfPaSOM+AQtaxm0ZhKrE6hY5W03cfVcA7JOd6q6qatx1Nx/G7bB
KKxDmWvZ0fO+DQhaVKc1maaAiwpJFmIWU8HSaRzoupf/+ETz+Blro5dy7QQuiDx8
xe8uKAEoIjeuscZZx0huuHVO5jw0dMH70mU2l+N27B7MhzU+v/X95G4GjeTsiu3u
6ZDQWgMPWhD8FBuUSgeNJ3O6zeKRuUfZ+qhn67lqdRzhvEeGhoB2JEFR3elaNiJB
W8BWb6N34Ysq8Z+fY4CzQRzEA9bonp3IDBGoh9wPPm8+10NZH2OHEeyeO5ftYuW6
uiLCGnf3Rm2Z0jN5iEJncJwHDNRcIFqwobOBEv8t6Ja8w3KlaaVPDrJ24tbn+GoW
Oz5Y9j/mic0VESpZJd96eS/GfVg7MfNY8oufOnm4irUAFXPhcBYGkL6xUwnQzSiy
356HKSI4iIUUEZul/9QBDCNHcGKfAcgRkcJJY6zoagnHoB5DVbTQuS/se+eSqhFe
nCkcbW/+bGiXoT9RiOhWrOcooS77R3CCrbFHAUv3VTyv0tvw01YFelorP6o7mCsK
rb6nj7/eCzXz0MyA2BdTfVQ5
=zanh
-----END PGP SIGNATURE-----
Merge tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc
Pull hwspinlock updates from Bjorn Andersson:
"This introduces devres helpers and an API to request a lock by name,
then migrates the sprd SPI driver to use these"
* tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc:
hwspinlock: Fix incorrect return pointers
spi: sprd: Change to use devm_hwspin_lock_request_specific()
spi: sprd: Replace of_hwspin_lock_get_id() with of_hwspin_lock_get_id_byname()
hwspinlock: Fix one comment mistake
hwspinlock: Remove redundant config
hwspinlock: Add devm_xxx() APIs to register/unregister one hwlock controller
hwspinlock: Add devm_xxx() APIs to request/free hwlock
hwspinlock: Add one new API to support getting a specific hwlock by the name
On systems where some controllers get a dynamic ID assigned and some have
a fixed number (e.g. from ACPI tables), the current implementation might
run into an IDR collision: in case of a fixed bus number is gotten by a
driver (but not marked busy in IDR tree) and a driver with dynamic bus
number gets the same ID and predictably fails.
Fix this by means of checking-in fixed IDsin IDR as far as dynamic ones
at the moment of the controller registration.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On non-OF systems spi->controlled_data may be NULL. This causes a NULL
pointer derefence on dm365-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When porting (Q)SPI controller drivers from the MTD layer to the SPI
layer, the naming scheme for the memory devices changes. To be able
to keep compatibility with the old drivers naming scheme, a name
field is added to struct spi_mem and a hook is added to let controller
drivers set a custom name for the memory device.
Example for the FSL QSPI driver:
Name with the old driver: 21e0000.qspi,
or with multiple devices: 21e0000.qspi-0, 21e0000.qspi-1, ...
Name with the new driver without spi_mem_get_name: spi4.0
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit removed include headers of linux/of.h and linux/of_platform.h,
because they are not used.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPI_3WIRE support to spi-gpio controller introducing
set_line_direction function pointer in spi_bitbang data structure.
Spi-gpio controller has been tested using hts221 temp/rh iio sensor
running in 3wire mode and lsm6dsm running in 4wire mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the capability to specify the flag parameter used in
bitbang_txrx_be_cpha{0,1} through the txrx_word function pointers of
spi_bitbang data structure. That feature will be used to add spi-3wire
support to the spi-gpio controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPI controller driver implemented in Socionext UniPhier SoCs.
UniPhier SoCs have two types SPI controllers; SCSSI supports a
single channel, and MCSSI supports multiple channels.
This driver supports SCSSI only.
This controller has 32bit TX/RX FIFO with depth of eight entry,
and supports the SPI master mode only.
This commit is implemented in PIO transfer mode, not DMA transfer.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if the chip select line is not controlled by the SPFI
hardware, the device select bits need to be set to specify
the chip select line in use for the hardware to know what
parameters to use for the current transfer.
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable count, l, mcspi and spi_cntrl are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'count' set but not used [-Wunused-but-set-variable]
warning: variable 'l' set but not used [-Wunused-but-set-variable]
warning: variable 'mcspi' set but not used [-Wunused-but-set-variable]
warning: variable 'spi_cntrl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the SPI controller deasserts the chip select when the TX fifo is
empty (which may happen in the middle of a transfer), the CS should be
handled by linux. Unfortunately, some or all of the first four chip
selects are not muxable as GPIOs, depending on the SoC.
There is a way to bitbang those pins by using the SPI boot controller so
use it to set the chip selects.
At init time, it is also necessary to give control of the SPI interface to
the Designware IP.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export dw_spi_set_cs so it can be used from the various IP integration
modules.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Log RX and TX fifo counters when a transfer is done and these are not
zero.
Signed-off-by: Tiago Brusamarello <tiago.brusamarello@datacom.ind.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dynamic burst mode allows to group together multiple words and send them
in one continuous burst. When the number of bytes to be sent is not a
strict multiple of the FIFO entry size (32 bits), the controller expects
the non aligned bits to be sent first.
This commit adds support for this particular constraint, avoiding the
need to send the non-aligned bytes one by one at the end of the
transfer, speeding-up transfer speed in that case.
With this method, a transfer is divided into multiple bursts, limited in
size by the maximum amount of data that the controller can transfer in
one continuous burst (which is 512 bytes).
The non-512 byte part of the transfer is sent first. The remaining bytes
to be transferred in the current burst is stored in the 'remainder'
field.
With this method, the read_u32 field is no longer necessary, and is
removed.
This was tested on imx6 solo and imx6 quad.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_imx_can_dma function computes the watermark level so that
the transfer will fit in exactly N bursts (without a remainder).
The smallest watermark level possible being one FIFO entry per burst, we
can't never have a case where the transfer size isn't divsiible by 1.
Remove the extra check for the wml being different than 0.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core enforces that we always use the next power-of-two number of
bytes to store words. As a result, a 24 bits word will be stored in 4
bytes.
This commit fixes the spi_imx_bytes_per_word function to return the
correct number of bytes.
This also allows to get rid of unnecessary checks in the can_dma
function, since the SPI core validates that we always have a transfer
length that is a multiple of the number of bytes per word.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dynamic bursts mode allows to group together multiple words into a
single burst. To do so, it's necessary that words can be packed into the
32-bits FIFO entries, so we can't allow using this mode with bit_per_words
different to 8, 16 or 32.
This prevents shitfing out extra clock ticks for transfers with
bit_per_word values not aligned on 8 bits.
With that , we are sure that only the correct number of bits is
shifted out at each transfer, so we don't need to mask out the remaining
parts of the words.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some fields in struct spi_imx_data are assigned a different value twice
in a row, in spi_imx_setupxfer.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPMSETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BizB/9lSfg4JrgJdAP8mDWfi7L5LjbpP9bB
9n1MlUFGRGU0Uc/yOD99QA6kB1WSpthFcgLBj+JDn3X30MzOqfZcHb3d9x5Z+XiV
YnIPzYqBPnnMSeTAX21c3Tz5nwO9hgz/xYr8onwYPeJWmt4RltYhiMdCgCQFWm9c
QaYNHiHymJP0ZFPXzLXlnIf+OW21ZOO9bH+eX1PAzbuWoDPxJZ63Eir22eKwTNey
bIIu19sxZE6o6Rd2Z0XAPtSGbd/r/9ULZAQcP429H+ETIfyefC6/IZv+yd4NrHmc
7WpWYi0JNdPLCXgLOvg5mwPBgDfs3tzoInWQu305882qlaK6kkivCgBu
=JPLR
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPMZgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JxACACAVtjwSy7KjJZ92ZljiyDP2MUydcM8
+6WiN96NCQVgMwFb6WBfePSJFeDeAnr0t4oANZpfa9rGV7YEYB5KlPmkGvuP+u6N
Jj+kRYXNcsu4LiyfZ82b/in3nBQ370Ufe32c4OECD/WDBLUx9TfWcur0sHLjHyp0
wh/9VxqQcGjgt/espt3QGDrASdymWHwF3sTEAoAIOeUzOgO61J2/4fQotUhPVPTN
q7jS6tmbR9GapEKGPOEzRz+3Ici3zK75zM3Yk2wSfh2xXk9Ly9q2HVO7ju7tC8Pe
XMnPxermqar/+PRgYYgLxrUDNyKHlzce4+hqc1cwj0XwAlvMiImB2nsB
=3WLv
-----END PGP SIGNATURE-----
Merge tag 'spi-dw-set-cs' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-4.19
spi: dw: Allow custom set_cs_callback
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible to get an interrupt as soon as it is requested. dw_spi_irq
does spi_controller_get_devdata(master) and expects it to be different than
NULL. However, spi_controller_set_devdata() is called after request_irq(),
resulting in the following crash:
CPU 0 Unable to handle kernel paging request at virtual address 00000030, epc == 8058e09c, ra == 8018ff90
[...]
Call Trace:
[<8058e09c>] dw_spi_irq+0x8/0x64
[<8018ff90>] __handle_irq_event_percpu+0x70/0x1d4
[<80190128>] handle_irq_event_percpu+0x34/0x8c
[<801901c4>] handle_irq_event+0x44/0x80
[<801951a8>] handle_level_irq+0xdc/0x194
[<8018f580>] generic_handle_irq+0x38/0x50
[<804c6924>] ocelot_irq_handler+0x104/0x1c0
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Upper layer users of SPI device drivers may rely on 'actual_length',
so it is important that information is correctly reported. One such
example is spi_mem_exec_op() function that will fail if
'actual_length' of the data transferred is not what was requested. Add
necessary code to populate 'actual_length.
Cc: Mark Brown <broonie@kernel.org>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: cphealy@gmail.com
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the missing clk_disable_unprepare() before return
from cnds_runtime_resume() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Registers of DSPI should not be accessed before enabling its clock. On
Toradex Colibri VF50 on Iris carrier board this could be seen during
bootup as imprecise abort:
Unhandled fault: imprecise external abort (0x1c06) at 0x00000000
Internal error: : 1c06 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.39-dirty #97
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
[<804166a8>] (regmap_write) from [<80466b5c>] (dspi_probe+0x1f0/0x8dc)
[<8046696c>] (dspi_probe) from [<8040107c>] (platform_drv_probe+0x54/0xb8)
[<80401028>] (platform_drv_probe) from [<803ff53c>] (driver_probe_device+0x280/0x2f8)
[<803ff2bc>] (driver_probe_device) from [<803ff674>] (__driver_attach+0xc0/0xc4)
[<803ff5b4>] (__driver_attach) from [<803fd818>] (bus_for_each_dev+0x70/0xa4)
[<803fd7a8>] (bus_for_each_dev) from [<803fee74>] (driver_attach+0x24/0x28)
[<803fee50>] (driver_attach) from [<803fe980>] (bus_add_driver+0x1a0/0x218)
[<803fe7e0>] (bus_add_driver) from [<803fffe8>] (driver_register+0x80/0x100)
[<803fff68>] (driver_register) from [<80400fdc>] (__platform_driver_register+0x48/0x50)
[<80400f94>] (__platform_driver_register) from [<8091cf7c>] (fsl_dspi_driver_init+0x1c/0x20)
[<8091cf60>] (fsl_dspi_driver_init) from [<8010195c>] (do_one_initcall+0x4c/0x174)
[<80101910>] (do_one_initcall) from [<80900e8c>] (kernel_init_freeable+0x144/0x1d8)
[<80900d48>] (kernel_init_freeable) from [<805ff6a8>] (kernel_init+0x10/0x114)
[<805ff698>] (kernel_init) from [<80107be8>] (ret_from_fork+0x14/0x2c)
Cc: <stable@vger.kernel.org>
Fixes: 5ee67b587a ("spi: dspi: clear SPI_SR before enable interrupt")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Ice Lake SPI host controller follows the Intel Cannon Lake but the
PCI IDs are different. Add the new PCI IDs to the driver supported
devices list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Change to use devm_hwspin_lock_request_specific() instead of
freeing the hwlock explicitly when unbound the device.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now the hwlock core has supplied new function to get a specific hwlock id
by one hwlock name, which is more clear for users. So change to use
of_hwspin_lock_get_id_byname().
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It seems that the proper structure field to use in this particular
case is *regmap_pushr* instead of regmap.
Addresses-Coverity-ID: 1470126 ("Copy-paste error")
Fixes: 58ba07ec79 ("spi: spi-fsl-dspi: Add support for XSPI mode registers")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Esben Haabendal <eha@deif.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the XSPI bit for devices configured for XSPI mode (currently LS1021A),
and thereby switch to extended SPI mode, allowing for SPI transfers using
from 4 to 32 bits per word instead of 4 to 16 bits per word.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This implements handling of split CMD and TX FIFO queues for XSPI when
running in TCFQ mode.
It should be simple to add it to EOQ mode also. Currently, EOQ mode is
only used with coldfire. So if coldfire DSPI supports XSPI, XSPI FIFO
handling should be added to EOQ mode also.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for adding support for extended SPI mode (XSPI), by extending
the regmap with the extra SREX and CTAREx registers.
An additional register map is made for allowing 16 bit access to CMD and TX
FIFO of the PUSHR register separately, which is also needed for XSPI mode
support.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark volatile registers to avoid caching bugs.
Note: SPI_MCR is marked volatile because of CLR_TXF and CLR_RXF bits.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCR register is not changed, so initialize it in dspi_init().
The exception is the CLR_TXF and CLR_RXF bits, which should be written to
before each transfer to make sure we start with empty FIFOs. With MCR
register now configured as volatile, the regmap_update_bits will do a real
read-modify-write cycle.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This extends the driver with support for all SPI framesizes from 4 to 16
bits, and adds support for per transfer specific bits_per_word, while at
the same time reducing code size and complexity.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify driver by avoiding counter wrapping by clearing transfer counter
on first SPI transfer per interrupt instead of tracking what it was before.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As of 92dc20d83a, transfer->cs_change has
been supported for non-last transfers, but not for last transfer.
This change brings handling of cs_change in line with the specification in
spi.h, implementing handling of transfer->cs_change for all transfers.
The value for CMD FIFO is precalculated with transfer->cs_change field
taken into account, allowing for CS de-activate between transfers and
keeping CS activated after last transfer.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking directly against pointer value should be at least as fast as doing
bitmasking and compare, so let's keep it simple.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The if statement just above this if/else statement triggers on the same
condition, and then invalidates it.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code did not de-assert any CS GPIOs before probing slaves. This
means that several CS signals could be active at once, garbling the
communication. Whether this was actually a problem depended on the type
of the SPI device attached (so my "spidev" for userspace access worked
correctly because its probe was effectively a no-op), and on the state
of the GPIO pins at SoC's boot.
The code was already iterating through all DT children of the SPI
controller, so this change re-uses that loop for CS GPIO setup as well.
This means that this might change the number of the HW CS signal which
is picked for all GPIO CS devices. Previously, the lowest one was used,
but we now use the first one from the DT.
With this move of the code, we can also finally initialize each GPIO CS
lane before registering the SPI controller (which in turn probes for
slaves).
I tried to fix this in 544248623b already, but that only did it half
way by registering the GPIOs properly. That patch failed to set their
logic signals early enough, though.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The path "spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()" added a usleep_range() function call,
which cannot be used in atomic context.
However the cdns_spi_fill_tx_fifo() function can be called during
an interrupt which may result in a kernel panic:
BUG: scheduling while atomic: grep/561/0x00010002
Modules linked in:
Preemption disabled at:
[<ffffff800858ea28>] wait_for_common+0x48/0x178
CPU: 0 PID: 561 Comm: grep Not tainted 4.17.0 #1
Hardware name: Cadence CSP (DT)
Call trace:
dump_backtrace+0x0/0x198
show_stack+0x14/0x20
dump_stack+0x8c/0xac
__schedule_bug+0x6c/0xb8
__schedule+0x570/0x5d8
schedule+0x34/0x98
schedule_hrtimeout_range_clock+0x98/0x110
schedule_hrtimeout_range+0x10/0x18
usleep_range+0x64/0x98
cdns_spi_fill_tx_fifo+0x70/0xb0
cdns_spi_irq+0xd0/0xe0
__handle_irq_event_percpu+0x9c/0x128
handle_irq_event_percpu+0x34/0x88
handle_irq_event+0x48/0x78
handle_fasteoi_irq+0xbc/0x1b0
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x84/0xf8
gic_handle_irq+0xc4/0x180
This patch replaces the function call with udelay() which can be
used in an atomic context, like an interrupt.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In case of a bi-directional transfer, receive DMA may complete in the
rcar-dmac driver before transmit DMA, due to scheduling latencies.
As the MSIOF driver waits for completion of the receive DMA only, it may
submit the next transmit DMA request before the previous one has
completed.
Make the driver more robust by waiting for the completion of both
receive and transmit DMA, when applicable.
Based on a patch in the BSP by Ryo Kataoka.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
The correct form is "a high-level", so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to section 59.2.4 MSIOF Receive Mode Register 1 (SIRMDR1) in
the R-Car Gen3 datasheet Rev.1.00, the value of the SIRMDR1.SYNCAC bit
must match the value of the SITMDR1.SYNCAC bit. However,
sh_msiof_spi_setup() changes only the latter.
Fix this by updating the SIRMDR1 register like the SITMDR1 register,
taking into account register bits that exist in SITMDR1 only.
Reported-by: Renesas BSP team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 7ff0b53c40 ("spi: sh-msiof: Avoid writing to registers from spi_master.setup()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5a686b2c9e ("spi: omap2-mcspi: Idle hardware during suspend
and resume") added calls for pm_runtime_force_suspend() and
pm_runtime_force_resume() to make sure spi is idled between
device_prepare() and device_complete().
But testing Linux next, I now noticed that we will get the following:
spi_master spi0: Failed to power device: -13
Looking at things more turns out we can just remove this non-standard
code. I was probably testing with some extra experimental patches
earlier when I thought we need pm_runtime_force_suspend() and
pm_runtime_force_resume().
Fixes: 5a686b2c9e ("spi: omap2-mcspi: Idle hardware during suspend
and resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If pm_runtime_get_sync() fails we should call pm_runtime_put_noidle().
This is probably not a critical fix as we should only hit this when
things are broken elsewhere.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
resource_size() is dereferencing the res without checking that it is
not NULL, so we need to do the check before calling resource_size().
Fixes: b95cb394ab ("spi: ti-qspi: Implement the spi_mem interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since Linux v4.10 release (commit 1d9174fbc5 "PM / Runtime: Defer
resuming of the device in pm_runtime_force_resume()"),
pm_runtime_force_resume() function doesn't runtime resume device if it was
not runtime active before system suspend. Thus, driver should not do any
register access after pm_runtime_force_resume() without checking the
runtime status of the device. To fix this issue, simply move
s3c64xx_spi_hwinit() call to s3c64xx_spi_runtime_resume() to ensure that
hardware is always properly initialized. This fixes Synchronous external
abort issue on system suspend/resume cycle on newer Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Patch http://patchwork.ozlabs.org/patch/905205/ has been partially
applied, and changes to the bcm-qspi driver have been lost somehow
(probably due to a conflict when applying the patch).
Remove the ->spi_flash_read() bits from this driver to fix the build
error.
Fixes: c1f5ba70de ("spi: Get rid of the spi_flash_read() API")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This API has been replaced by the spi_mem_xx() one, its only user
(spi-nor) has been converted to spi_mem_xx() and all SPI controller
drivers that were implementing the ->spi_flash_xxx() hooks are also
implementing the spi_mem ones. So we can safely get rid of this API.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_mem interface is meant to replace the spi_flash_read() one.
Implement the ->exec_op() method so that we can smoothly get rid of the
old interface.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_mem interface is meant to replace the ->spi_flash_read() one.
Implement the ->exec_op() method to ease removal of the old interface.
Not that ->spi_flash_read() is now implemented as a wrapper around the
new bcm_qspi_exec_mem_op() function so that we can easily get rid of
it when ->spi_flash_read() is removed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Tested-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI/QuadSPI controllers only expose a high-level SPI memory
interface, thus preventing any regular SPI transfers from being done.
In that case, SPI controller drivers can leave all ->transfer_xxx()
hooks empty and only implement the spi_mem_ops interface.
Adjust the core to allow such situations:
- extend spi_controller_check_ops() to accept situations where all
->transfer_xxx() pointers are NULL only if ->mem_ops != NULL
- make sure we do not initialize the SPI message queue if
ctlr->transfer_one and ctlr->transfer_one_message are missing
- return -ENOTSUPP if someone tries to do a regular SPI transfer on
a controller that does not support it
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.
This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
I accidentally sent an early version of patch removing spi-bcm53xx
driver which got rid of .c and .h files *only*. I amended local commit
but forgot to re-format the patch.
This commit removes leftovers of dropped driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver was added by commit 0fc6a323e1 ("spi: bcm53xx: driver for
SPI controller on Broadcom bcma SoC") back in 2014. It was needed to
provide a minimal support for SPI controller on BCM5301X (AKA Northstar)
devices.
An alternative driver was added by Kamal in commit fa236a7ef2 ("spi:
bcm-qspi: Add Broadcom MSPI driver") 2 years later. It supports the same
hardware but for some reason a new driver has been developed for it.
At this point the new driver supports: more modes, setting a speed,
setting bits per word and uses IRQs instead of polling. DTS file for
BCM5301X has also been updated in the commit 1c8f406507 ("ARM: dts:
BCM5301X: convert to iProc QSPI") - over a year ago.
That explained I see no reason to keep the old driver alive.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() can fail, so its return value should be checked and
acted upon.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3343b7a6d2 ("spi/pxa2xx: convert to the common clk framework")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 AUX SPI has a shared interrupt line (with AUX UART).
Downstream fixes this with an AUX irqchip to demux the IRQ sources and a
DT change which breaks compatibility with older kernels. The AUX irqchip
was already rejected for upstream[1] and the DT change would break
working systems if the DTB is updated to a newer one. The latter issue
was brought to my attention by Alex Graf.
The root cause however is a bug in the shared handler. Shared handlers
must check that interrupts are actually enabled before servicing the
interrupt. Add a check that the TXEMPTY or IDLE interrupts are enabled.
[1] https://patchwork.kernel.org/patch/9781221/
Cc: Alexander Graf <agraf@suse.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-spi@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently are calling mcspi suspend and resume without considering
that mcspi might provide resources for other device driver such as
regulators. This means resume can fail and will produce -EACCES if
errors if anything calls mcspi functions between device_prepare()
and device_complete().
To fix the issue, let's do the following changes:
1. Let's add checking for return values for pm_runtime_get calls,
and call pm_runtime_put_noidle() on errors. Things still fail
after this change, but at least we see something is wrong as
we now see -EACCES errors on resume.
2. Let's use noirq level for suspend and resume as other drivers
can still call SPI related functions on suspend and resume. This
still won't fix the -EACCES issue, but gets us to something a bit
saner.
3. Finally, let's modify suspend and resume to call to make sure
the device is idled properly on suspend. We have device_prepare()
call pm_runtime_get_noresume() that won't get released until in
device_complete() when it calls pm_runtime_put(). So if SPI is
still active on entering suspend, it will never get idled unless
we add calls to pm_runtime_force_suspend() and resume. This also
fixes the -EACCES errors on resume together with changes 1 and 2
above.
And since we're already rewriting suspend resume functions, let's
arrange the order of suspend and resume functions to be like they
usually are with suspend first.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can have the SoC enter off mode also during idle, not just
during suspend. Currently we are handling the CS restore properly
for unused CS only for resume and not for runtime resume.
Let's just move all the context related restore to runtime_resume().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_spi_register_master() fails in meson_spicc_probe(),
spicc->core is left undisabled. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Always confirm the BSPI_MAST_N_BOOT_CTRL bit when enabling
or disabling BSPI transfers.
Fixes: 4e3b2d236f ("spi: bcm-qspi: Add BSPI spi-nor flash controller driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Added fix for probing of spi-nor device non-zero chip selects. Set
MSPI_CDRAM_PCS (peripheral chip select) with spi master for MSPI
controller and not for MSPI/BSPI spi-nor master controller. Ensure
setting of cs bit in chip select register on chip select change.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Replace the manual validity checks for the GPIO with the
gpio_is_valid().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Right now, no checks are done on the presence of a ->transfer[_xxx]()
method, which can lead to a NULL pointer dereference when someone
starts sending something on the bus.
Do the check at registration time and refuse to add the controller if
all ->transfer[_xxx]() pointers are NULL.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable the clock prior to calling clk_get_rate(), because clk_get_rate()
should only be called if the clock is enabled.
Additionally, prepare/enable the pll_clk before calling clk_get_rate()
for the same reason.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 142168eba9 ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the 32-bit device address only is supported for DMA. However,
starting from Intel Sunrisepoint PCH the DMA address of the device FIFO
can be 64-bit.
Change the respective variable to be compatible with DMA engine
expectations, i.e. to phys_addr_t.
Fixes: 34cadd9c1b ("spi: pxa2xx: Add support for Intel Sunrisepoint")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This is needed by the spi-mem logic to force all messages that have been
queued before a memory operation to be sent before we start the memory
operation. We do that in order to guarantee that spi-mem operations do
not preempt regular SPI transfers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_{map,unmap}_buf() are needed by the spi-mem logic that is about to
be introduced to prepare data buffer for DMA operations.
Remove the static specifier on these functions and add their prototypes
to drivers/spi/internals.h. We do not export the symbols here because
both SPI_MEM and SPI can't be enabled as modules and we'd like to
prevent controller/device drivers from using these functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the 32-bit device address only is supported for DMA. However,
starting from Intel Sunrisepoint PCH the DMA address of the device FIFO
can be 64-bit.
Change the respective variable to be compatible with DMA engine
expectations, i.e. to phys_addr_t.
Fixes: 34cadd9c1b ("spi: pxa2xx: Add support for Intel Sunrisepoint")
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some variants of the SPI controller have no DMA support, in such case
SPI transfers longer than the FIFO length are not currently properly
handled by the driver. Fix it by doing multiple transfers in the
s3c64xx_spi_transfer_one() function if the SPI transfer length exceeds
the FIFO size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
More references to fifo_len are added in subsequent patch.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a s3c64xx_ prefix to remaining generic function names so it is clear
the code is part of the driver when grepping or looking at debug logs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi pointer argument is not used now so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of xspi work in busy condition, may send bytes failed.
once something wrong, spi controller did't work any more
My test found this situation appear in both of read/write process.
so when TX FIFO is full, add one byte delay before send data;
Signed-off-by: sxauwsk <sxauwsk@163.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the pump_transfers() transfer tasklet to transfer_one() hook the
SPI core calls to process single transfer instead of handling message
processing and chip select handling in the driver. This not only
simplifies the driver but also brings transfer statistics from the core.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are going to rename and modify pump_transfers(). Prepare for it by
removing the string "pump_transfers:" from error and warning prints.
While at it make these user-visible strings single line in sources as it
helps source grepping from error reports.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vignesh R
Piotr Bugalski
Mark Brown
Mason Yang
Wolfram Sang
Alok Chauhan
Chuanhua Han
Leilk Liu
Jarkko Nikula
Emil Renner Berthing
Linus Torvalds
Florian Fainelli
Ludovic Barre
Christoph Hellwig
Sergei Shtylyov
Robin Gong
Phil Elwell
Lubomir Rintel
Girish Mahadevan
Huibin Hong
Talel Shenhar
Rafał Miłecki
Trent Piepho
Axel Lin
Hieu Tran Dang
Nathan Chancellor
Lukasz Majewski
Gustavo A. R. Silva
Greg Kroah-Hartman
Marco Felsch
Geert Uytterhoeven
Arnd Bergmann
Boris Brezillon
David Lechner
Peter Shih
Jonas Gorski
Alexey Khoroshilov
YueHaibing
Linus Walleij
Lee Jones
Radu Pirea
Simon Goldschmidt
Hiromitsu Yamasaki
Gaku Inami
Kosta Zertsekel
Marcel Ziswiler
Alexandre Belloni
Lanqing Liu
Angelo Dureghello
Kirill Kapranov
Bartosz Golaszewski
Frieder Schrempf
Keiji Hayashibara
Lorenzo Bianconi
Ionela Voinescu
Colin Ian King
Tiago Brusamarello
Maxime Chevallier
Fabio Estevam
Andrey Smirnov
Wei Yongjun
Krzysztof Kozlowski
Mika Westerberg
Baolin Wang
Esben Haabendal
Jan Kundrát
Janek Kotas
Kees Cook
Rafael J. Wysocki
Tony Lindgren
Marek Szyprowski
Ulf Hansson
Tobias Jordan
Rob Herring
Kamal Dasu
Arvind Yadav
Stefan Potyra
Andy Shevchenko
Sylwester Nawrocki
kbuild test robot
sxauwsk
Geert Uytterhoeven