This refactors the changes to the GPIO line naming mechanism to
not have so widespread effects, instead we conclude the patch series
by having created a name attribute in the GPIO descriptor, that need
not be globally unique, and it will be initialized from the old
.names array in struct gpio_chip if it exists, then used in the legacy
sysfs code like the array was used previously.
The associated changes to name lines from the device tree are
controversial and need to stand alone from this. Resulting changes:
1. Remove the export and the header for the gpio_name_to_desc() as so
far the only use is inside gpiolib.c. Staticize gpio_name_to_desc()
and move it above the only function using it.
2. Only print a warning if there are two GPIO lines with the same name.
The reason is to preserve current behaviour: before the previous
changes to the naming mechanism this would not reject probing the
driver, instead the error would occur when trying to export the line
in sysfs, so restore this behaviour, but print a friendly warning
if names collide.
Cc: Johan Hovold <johan@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add some information about gpio names to the debugfs gpio file. name and
label of a GPIO are then displayed next to each other. This way it is
easy to see what the real name of GPIO is and what the driver requested
it for.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[Dropped unsolicited sysfs ABI patch hunk]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds GPIO names to the GPIO descriptors when initializing the
gpiochip. It also introduces a check whether any of the new names will
conflict with an existing GPIO name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest gpio hogging mechanism assigns each gpio a 'line-name' in the
devicetree. The 'name' field is different from the 'label' field.
'label' is only used for requested GPIOs to describe its current use by
driver or userspace.
The 'name' field describes the GPIO itself, not the use. This is most
likely identical to the label in the schematic on the GPIO line and
should help to find this particular GPIO.
This is equivalent to the gpiochip->names array. However names should be
stored in the GPIO descriptor. We will use gpiochip->names in the future
only as initializer for the GPIO descriptors for drivers that assign
GPIO names hardcoded. All other GPIO names will be parsed from DT and
directly assigned to the GPIO descriptor.
This patch adds a helper function to find gpio descriptors by name
instead of gpio number.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make device_get_next_child_node() work with ACPI data-only subnodes
introduced previously.
Namely, replace acpi_get_next_child() with acpi_get_next_subnode()
that can handle (and return) child device objects as well as child
data-only subnodes of the given device and modify the ACPI part
of the GPIO subsystem to handle data-only subnodes returned by it.
To that end, introduce acpi_node_get_gpiod() taking a struct
fwnode_handle pointer as the first argument. That argument may
point to an ACPI device object as well as to a data-only subnode
and the function should do the right thing (ie. look for the matching
GPIO descriptor correctly) in either case.
Next, modify fwnode_get_named_gpiod() to use acpi_node_get_gpiod()
instead of acpi_get_gpiod_by_index() which automatically causes
devm_get_gpiod_from_child() to work with ACPI data-only subnodes
that may be returned by device_get_next_child_node() which in turn
is required by the users of that function (the gpio_keys_polled
and gpio-leds drivers).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Modify is_acpi_node() to return "true" for ACPI data-only subnodes as
well as for ACPI device objects and change the name of to_acpi_node()
to to_acpi_device_node() so it is clear that it covers ACPI device
objects only. Accordingly, introduce to_acpi_data_node() to cover
data-only subnodes in an analogous way.
With that, make the fwnode_property_* family of functions work with
ACPI data-only subnodes introduced previously.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It's possible to have gpio chips hanging off unreliable remote buses
where the get() operation will fail to acquire a readout of the current
gpio state. Propagate these errors to the consumer so that they can
act on, retry or ignore these failing reads, instead of treating them as
the line being held high.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Since IRQ chip helpers were introduced drivers lose ability to
register separate lockdep classes for each registered GPIO IRQ
chip and the gpiolib now is using shared lockdep class for
all GPIO IRQ chips (gpiochip_irq_lock_class).
As result, lockdep will produce warning when there are min two
stacked GPIO chips and all of them are interrupt controllers.
HW configuration which generates lockdep warning (TI dra7-evm):
[SOC GPIO bankA.gpioX]
<- irq - [pcf875x.gpioY]
<- irq - DevZ.enable_irq_wake(pcf_gpioY_irq);
The issue was reported in [1] and discussed [2].
=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted
---------------------------------------------
sh/63 is trying to acquire lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
but task is already holding lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(class);
lock(class);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by sh/63:
#0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164
#1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0
#2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0
#3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4
#4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398
#5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94
#6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
stack backtrace:
CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14)
[<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c)
[<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20)
[<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128)
[<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c)
[<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94)
[<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc)
[<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54)
[<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc)
[<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4)
[<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124)
[<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398)
[<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4)
[<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728)
[<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4)
[<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8)
[<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0)
[<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8)
[<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164)
[<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c)
[<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54)
Lets fix it by using separate lockdep class for each registered GPIO
IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros.
The implementation of this patch inspired by solution done by Nicolas
Boichat for regmap [3]
[1] http://www.spinics.net/lists/linux-gpio/msg05844.html
[2] http://www.spinics.net/lists/linux-gpio/msg06021.html
[3] http://www.spinics.net/lists/arm-kernel/msg429834.html
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Tested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the driver has specified its own irq_{request/release}_resources()
functions, don't override them. The gpio-etraxfs driver will use this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
[Added a small comment blurb]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER if
the pin controller isn't available.
Otherwise, the GPIO range wouldn't be set at all unless the pin
controller probed always before the GPIO chip.
With this change, the probe of the GPIO chip will be deferred and will
be retried at a later point, hopefully once the pin controller has been
registered and probed already.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed as most platforms don't use probing.
There appears to be a great deal of blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This variable is used as an iterator and initialized in the
list_for_each() loop.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case we unload and load a driver module again that is registering a
lookup table, without this it will result in multiple entries. Provide
an option to remove the lookup table on driver unload
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVmj+OAAoJEMH8FHityuwJHGcH/A5bSLcdaFCMcrYceYD/odzR
X/mer/CcW/uWG0sUha2pZjT172szSrm0/Bk+SaY5Ub0c6ssCpKRGhtqZNVWWz44V
duRQGkYEFODHSed1XnKQyKwr6nLyhjmj8RuP5GokjcsBZyl4onj+NHgmpH5aQBYC
4NyFpIXcSS4jCwj4nsZu4Y2xLAgu/t5oVzqDheqTyZ9imgaR8hbyminKhN+wFfrI
FKukShQ5AQPVs7pGEqeY0wgJp+keOIYLukLwvgZw+S7MxixXaPiSK1Ez9DPY9CFo
f+NkDV6GIe4OAOGFsL9dCxR0sO6mF7C5PpYuDUBtISi3JHNAvW+Ri7FKPeSDikA=
=ixJj
-----END PGP SIGNATURE-----
Merge tag 'gpiod-flags-for-4.3' of git://git.pengutronix.de/git/ukl/linux into devel
The last patch in this series makes the flags parameter for the various
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
Assign GPIO chip owner field to chip->dev->driver->owner if it was not
configured by GPIO driver.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now nothing prevents GPIO driver from being unloaded if its gpios
were requested as GPIO IRQs only (without calling gpio_request()).
Hence, add calls of try_module_get()/module_put() into
gpiochip_irq_reqres/relres() to track such scenario properly.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_add_pingroup_range() has a pctldev argument, not pinctrl.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Now that all[1] users of the gpiod_get functions are converted to make
use of the up to now optional flags parameter, make it mandatory which
allows to remove some cpp magic.
[1] all but etraxfs-uart which is broken anyhow and I'm allowed to
ignore it by Jesper Nilsson :-)
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* acpi-video:
ACPI / video: Inline acpi_video_set_dmi_backlight_type
* device-properties:
ACPI / OF: Rename of_node() and acpi_node() to to_of_node() and to_acpi_node()
* pm-sleep:
PM / sleep: Increase default DPM watchdog timeout to 60
PM / hibernate: re-enable nonboot cpus on disable_nonboot_cpus() failure
* pm-cpuidle:
tick/idle/powerpc: Do not register idle states with CPUIDLE_FLAG_TIMER_STOP set in periodic mode
Commit 8a0662d9 introduced of_node and acpi_node symbols in global namespace
but there were already ~63 of_node local variables or function parameters
(no single acpi_node though, but anyway).
After debugging undefined but used of_node local varible (which turned out
to reference static function of_node() instead) it became clear that the names
for the functions are too short and too generic for global scope.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
This patch fixes some issues given by checkpatch. Fixes include
bracket placement, spacing and indenting.
Signed-off-by: Daniel Lockyer <thisisdaniellockyer@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When requesting own descriptors through hogs, it is useful to
get some details about what's going on if we encounter problems.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These error messages are helpful to see that we fail to get
hogs. Promote them to real errors so they appear in the boot
crawl.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up chained handler and handler data if they were set by
gpiochip_set_chained_irqchip().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to free any hogged gpios on errors in gpiochip_add.
Also move all forward declarations to the top of the file.
Fixes: f625d46017 ("gpio: add GPIO hogging mechanism")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the gpio-chip export/unexport functions to the more descriptive
names gpiochip_sysfs_register and gpiochip_sysfs_unregister.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up gpiochip_remove somewhat and only output warning about removing
chip with GPIOs requested once.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If dev is NULL in __gpiod_get_index() and both ACPI and OF are
enabled, it will be checked twice before the code decides to give
up with DT/ACPI lookup, so avoid that.
Also use the observation that ACPI_COMPANION() is much more efficient
than ACPI_HANDLE(), because the latter uses the former and carries out
a check and a pointer dereference on top of it, so replace the
ACPI_HANDLE() check with an ACPI_COMPANION() one which does not
require the additional IS_ENABLED(CONFIG_ACPI) check too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions for conveniently obtaining and disposing of
an entire array of GPIOs with one function call.
ACPI parts tested by Mika Westerberg, DT parts tested by Rojhalat
Ibrahim.
Change log:
v5: move the ACPI functions to gpiolib-acpi.c
v4: - use shorter names for members of struct gpio_descs
- rename lut_gpio_count to platform_gpio_count for clarity
- add check for successful memory allocation
- use ERR_CAST()
v3: - rebase on current linux-gpio devel branch
- fix ACPI GPIO counting
- allow for zero-sized arrays
- make the flags argument mandatory for the new functions
- clarify documentation
v2: change interface
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Avoid multiple identical definitions of the gpio suffix strings by putting
them into a global constant array.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on Boris Brezillion's work this is a reworked patch
of his initial GPIO hogging mechanism.
This patch provides a way to initially configure specific GPIO
when the GPIO controller is probed.
The actual DT scanning to collect the GPIO specific data is performed
as part of gpiochip_add().
The purpose of this is to allow specific GPIOs to be configured
without any driver specific code.
This is particularly useful because board design are getting
increasingly complex and given SoC pins can now have more
than 10 mux values, a lot of connections are now dependent on
external IO muxes to switch various modes.
Specific drivers should not necessarily need to be aware of
what accounts to a specific board implementation. This board level
"description" should be best kept as part of the dts file.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing
memory-mapped OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for
switching several lines at once, a feature merged in
the last cycle.
- New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
- Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
- New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
- Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
- Various minor cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yWrB
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the GPIO bulk changes for the v3.20 series:
GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing memory-mapped
OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for switching
several lines at once, a feature merged in the last cycle.
New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
Various minor cleanups and bug fixes"
* tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: kconfig: replace PPC_OF with PPC
gpio: pxa: add PXA1928 gpio type support
dt/bindings: gpio: add compatible string for marvell,pxa1928-gpio
gpio: pxa: remove mach IRQ includes
gpio: max732x: use an inline function for container cast
gpio: use sizeof() instead of hardcoded values
gpio: max732x: add set_multiple function
gpio: sch: Consolidate similar algorithms
gpio: tz1090-pdc: Use resource_size to fix off-by-one resource size calculation
gpio: ge: Convert to use devm_kstrdup
gpio: correctly use const char * const
gpio: sx150x: fixup OF support
gpio: mpc8xxx: Use of_mm_gpiochip_remove
gpio: Add Fujitsu MB86S7x GPIO driver
gpio: mpc8xxx: Convert to platform device interface.
gpio: zevio: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_property_read_u32
gpio: gpio-mm-lantiq: Do not replicate code
gpio :gpio-mm-lantiq: Use devm_kzalloc
...
gpiolib uses a fixed string for the suffixes and defines it at 32 bytes.
Later in the code snprintf is used with this fixed value of 32. Using
sizeof() is safer in case the size for the suffixes is ever changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On my previous patch I was overly hasty and made the suffixes string
array
const char const *suffixes, instaed of const char * const suffixes. This
patch corrects that
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Checkpatch complains, and probably with good reason that we should use
const char const * for the static constant array that never gets
changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unregister gpiochip device (used to export information through sysfs)
before removing it internally. This way removal will reverse addition.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move direct and indirect calls to gpiochip_remove_pin_ranges outside of
spin lock as they can end up taking a mutex in pinctrl_remove_gpio_range.
Note that the pin ranges are already added outside of the lock.
Fixes: 9ef0d6f762 ("gpiolib: call pin removal in chip removal function")
Fixes: f23f1516b6 ("gpiolib: provide provision to register pin ranges")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak and sleep-while-atomic in gpiochip_remove.
The memory leak was introduced by afa82fab5e ("gpio / ACPI: Move event
handling registration to gpiolib irqchip helpers") that moved the
release of acpi interrupt resources to gpiochip_irqchip_remove, but by
then the resources are no longer accessible as the acpi_gpio_chip has
already been freed by acpi_gpiochip_remove.
Note that this also fixes a few potential sleep-while-atomics, which has
been around since 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
when the call to gpiochip_irqchip_remove while holding a spinlock was
added (a couple of irq-domain paths can end up grabbing mutexes).
Fixes: afa82fab5e ("gpio / ACPI: Move event handling registration to
gpiolib irqchip helpers")
Fixes: 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix potential corruption of gpio-chip list due to failure to remove the
chip from the list before returning in gpiochip_add error path.
The chip could be long gone when the global list is next traversed,
something which could lead to a null-pointer dereference. In the best
case (chip not deallocated) we are just leaking the gpio range.
Fixes: 14e85c0e69 ("gpio: remove gpio_descs global array")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Memory allocated and references taken by of_gpiochip_add and
acpi_gpiochip_add were never released on errors in gpiochip_add (e.g.
failure to find free gpio range).
Fixes: 391c970c0d ("of/gpio: add default of_xlate function if device
has a node pointer")
Fixes: 664e3e5ac6 ("gpio / ACPI: register to ACPI events
automatically")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
Commit 14e85c0e69 ("gpio: remove gpio_descs global array") changed
gpio_to_desc()'s behavior to return NULL not only for GPIOs numbers
not in the valid range, but also for all GPIOs whose controller has not
been probed yet. Although this behavior is more correct (nothing hints
that these GPIO numbers will be populated later), this affects
gpio_request() and gpio_request_one() which call gpiod_request() with a
NULL descriptor, causing it to return -EINVAL instead of the expected
-EPROBE_DEFER for a non-probed GPIO.
gpiod_request() is only called with a descriptor obtained from
gpio_to_desc() from these two functions, so address the issue there.
Other ways to obtain GPIOs rely on well-defined mappings and can thus
return -EPROBE_DEFER only for relevant GPIOs, and are thus not affected
by this issue.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ARCH_NR_GPIOS-sized static array of GPIO descriptors by
dynamically-allocated arrays for each GPIO chip.
This change makes gpio_to_desc() perform in O(n) (where n is the number
of GPIO chips registered) instead of O(1), however since n is rarely
bigger than 1 or 2 no noticeable performance issue is expected.
Besides this provides more incentive for GPIO consumers to move to the
gpiod interface. One could use a O(log(n)) structure to link the GPIO
chips together, but considering the low limit of n the hypothetical
performance benefit is probably not worth the added complexity.
This patch uses kcalloc() in gpiochip_add(), which removes the ability
to add a chip before kcalloc() can operate. I am not aware of such
cases, but if someone bisects up to this patch then I will be proven
wrong...
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't make much sense to make some (possible expensive) calls to
gpio_is_valid() first, and to ignore the result if the base number is
negative. Check for a positive base number first.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers need to deal with only firmware representation of its
GPIOs. An example would be a GPIO button array driver where each button
is described as a separate firmware node in device tree. Typically these
child nodes do not have physical representation in the Linux device
model.
In order to help device drivers to handle such firmware child nodes we
add dev[m]_get_named_gpiod_from_child() that takes a child firmware
node pointer as its second argument (the first one is the parent device
itself), finds the GPIO using whatever is the underlying firmware
method, and requests the GPIO properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With release of ACPI 5.1 and _DSD method we can finally name GPIOs (and
other things as well) returned by _CRS. Previously we were only able to
use integer index to find the corresponding GPIO, which is pretty error
prone if the order changes.
With _DSD we can now query GPIOs using name instead of an integer index,
like the below example shows:
// Bluetooth device with reset and shutdown GPIOs
Device (BTH)
{
Name (_HID, ...)
Name (_CRS, ResourceTemplate ()
{
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {15}
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {27, 31}
})
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () {"reset-gpio", Package() {^BTH, 1, 1, 0 }},
Package () {"shutdown-gpio", Package() {^BTH, 0, 0, 0 }},
}
})
}
The format of the supported GPIO property is:
Package () { "name", Package () { ref, index, pin, active_low }}
ref - The device that has _CRS containing GpioIo()/GpioInt() resources,
typically this is the device itself (BTH in our case).
index - Index of the GpioIo()/GpioInt() resource in _CRS starting from zero.
pin - Pin in the GpioIo()/GpioInt() resource. Typically this is zero.
active_low - If 1 the GPIO is marked as active_low.
Since ACPI GpioIo() resource does not have field saying whether it is
active low or high, the "active_low" argument can be used here. Setting
it to 1 marks the GPIO as active low.
In our Bluetooth example the "reset-gpio" refers to the second GpioIo()
resource, second pin in that resource with the GPIO number of 31.
This patch implements necessary support to gpiolib for extracting GPIOs
using _DSD device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUNOr0AAoJEEEQszewGV1z9toP/2ISXRnsi3+jlqVmEGm/y6EA
PPwJOiYnOhZR2/fTCHIF0PNbIi9pw7xKnzxttYCu4uCz7geHX+FfTwUZ2/KWMfqi
ZJ9kEoOVVKzKjmL/m2a2tO4IRSBHqJ8dF3yvaNjS3AL7EDfG6F5STErQurdLEynK
SeJZ2OwM/vRFCac6F7oDlqAUTu3xYGbVD8+zI0H0V/ReocosFlEwcbl2S8ctDWUd
h98M+gY+A8rxkvVMnmQ/k7rUTme/glDQ3z5xVx+uHbS2/a5M1jSM/71cXE6YnSrR
it0CK7CHomq2RzHsKf7oH7GD4kFkukMwFKeMoqz75JWz3352VZPTF53chCIqRSgO
hrgGwZ7WF6pUUUhsn1ZdZsnBPA2Fou2uwslyLSAiE+OYEH2/NSVIOUcorjQcWqU/
0Kix5yb8X1ZzRMhR+TVrTD5V0jguqp2buXq+0P2XlU6MoO2vy7iNf2eXvPg8sF8C
anjTCKgmkzy7eyT2uzfDaNZAyfSBKb1TiKiR9zA0SRChJkCi1ErJEXDGeHiptvSA
+D2k68Ils2LqsvdrnEd2XvVFMllh0iq7b+16o7D+Els0WRbnHpfYCaqfOuF5F4U0
SmeyI0ruawNDc5e9EBKXstt0/R9AMOetyTcTu29U2ZVo90zGaT1ofT8+R1jJ0kGa
bPARJZrgecgv1E9Qnnnd
=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
To unify how we connect cascaded IRQ chips to parent IRQs, if
NULL us passed as handler to the gpiochip_set_chained_irqchip()
function, assume the chips is nested rather than chained, and
we still get the parent set up correctly by way of this function
call.
Alter the drivers for tc3589x and stmpe to use this to set up
their chained handlers as a demonstration of the usage.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the IRQ from the parent is nested the IRQ may need to be
resent under certain conditions. Currently the chained IRQ
handler in gpiolib does not handle connecting nested IRQs
but it is conceptually correct to indicate the actual parent
IRQ.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no guarantee that VIRQs will be allocated sequentially
for gpio irqchip in gpiochip_irqchip_add().
Therefore, it's unsafe to dispose VIRQ in gpiochip_irqchip_remove()
basing on index relatively to stored irq_base value.
Hence, use irq_find_mapping for VIRQ finding in gpiochip_irqchip_remove()
instead of irq_base + index.
Reported-by: Wang, Yalin <Yalin.Wang@sonymobile.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is possibility with misconfigured pins that interrupt occurs instantly
after setting irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Now if handler gets called before irq_set_handler_data() the handler gets
NULL handler data.
Fix this by moving irq_set_handler_data() call before
irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Cc: Stable <stable@vger.kernel.org> # 3.15+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
GPIO direction flags are not getting set because
an 'if' statement is the wrong way around.
Cc: Stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current prototype of gpiochip_request_own_desc() requires to obtain
a pointer to a descriptor. This is in contradiction to all other GPIO
request schemes, and imposes an extra step of obtaining a descriptor to
drivers. Most drivers actually cannot even perform that step since the
function that does it (gpichip_get_desc()) is gpiolib-private.
Change gpiochip_request_own_desc() to return a descriptor from a
(chip, hwnum) tuple and update users of this function (currently
gpiolib-acpi only).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The huge majority of GPIOs have their direction and initial value set
right after being obtained by one of the gpiod_get() functions. The
integer GPIO API had gpio_request_one() that took a convenience flags
parameter allowing to specify an direction and value applied to the
returned GPIO. This feature greatly simplifies client code and ensures
errors are always handled properly.
A similar feature has been requested for the gpiod API. Since setting
the direction of a GPIO is so often the very next action done after
obtaining its descriptor, we prefer to extend the existing functions
instead of introducing new functions that would raise the
number of gpiod getters to 16 (!).
The drawback of this approach is that all gpiod clients need to be
updated. To limit the pain, temporary macros are introduced that allow
gpiod_get*() to be called with or without the extra flags argument. They
will be removed once all consumer code has been updated.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both functions were introduced to let gpio drivers request their own
gpio pins. Without exporting the functions, this can however only be
used by gpio drivers built into the kernel.
Secondary impact is that the functions can not currently be used by
platform initialization code associated with the gpio-pca953x driver.
This code permits auto-export of gpio pins through platform data, but
if this functionality is used, the module can no longer be unloaded due
to the problem solved with the introduction of gpiochip_request_own_desc
and gpiochip_free_own_desc.
Export both function so they can be used from modules and from
platform initialization code.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_ensure_requested() only makes sense when using the integer-based
GPIO API, so make sure it is called from there instead of the gpiod
API which we know cannot be called with a non-requested GPIO anyway.
The uses of gpio_ensure_requested() in the gpiod API were kind of
out-of-place anyway, so putting them in gpio-legacy.c helps clearing the
code.
Actually, considering the time this ensure_requested mechanism has been
around, maybe we should just turn this patch into "remove
gpio_ensure_requested()" if we know for sure that no user depend on it
anymore?
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO descriptors are not going to remain unique anymore, having this
function public is not safe. Restrain its use to gpiolib since we have
no user outside of it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Compiling out GPIO labels results in a space gain so small that it can
hardly be justified. Labels can also be useful for printing debug
messages, so always keep them around.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit dd34c37aa3 (gpio: of: Allow -gpio suffix for property names)
added parsing for both -gpio and -gpios suffix but also changed
the handling for deferred probe unintentionally. Because of the
looping the second name will now return -ENOENT instead of
-EPROBE_DEFER. Fix the issue by breaking out of the loop if
-EPROBE_DEFER is encountered.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce gpiod_get_optional() and gpiod_get_index_optional() helpers
that make it easier for drivers to handle optional GPIOs.
Currently in order to handle optional GPIOs, a driver needs to special
case error handling for -ENOENT, such as this:
gpio = gpiod_get(dev, "foo");
if (IS_ERR(gpio)) {
if (PTR_ERR(gpio) != -ENOENT)
return PTR_ERR(gpio);
gpio = NULL;
}
if (gpio) {
/* set up GPIO */
}
With these new helpers the above is reduced to:
gpio = gpiod_get_optional(dev, "foo");
if (IS_ERR(gpio))
return PTR_ERR(gpio);
if (gpio) {
/* set up GPIO */
}
While at it, device-managed variants of these functions are also
provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function is called gpiod_get(), not gpio_get(). Fix the kernel-doc
comment to match the name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many bindings use the -gpio suffix in property names. Support this in
addition to the -gpios suffix when requesting GPIOs using the new
descriptor-based API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_find_gpio() is always called under an IS_ENABLED(CONFIG_OF), so the
dummy implementation provided for !OF configurations is not needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO irqchip drivers exploit the irqdomain mapping
function to set up the IRQ default type in the hardware,
make sure that if we pass IRQ_TYPE_NONE, no hardware setup
whatsoever takes place (this should be the norm) until
later when the IRQ gets utilized.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: linux-omap <linux-omap@vger.kernel.org>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Another feature that is duplicated in a number of GPIO irqchips
is that these cascades IRQs are assigned their own lock class
so as to avoid warnings about lockdep recursions. Do this also
in the generic GPIO irqchip helpers for smooth transition to
this core infrastructure.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some off-chip GPIO expanders need to be communicated by I2C or
SPI traffic, but may still support IRQs. By the sleeping nature
of such buses, such IRQ handlers need to be threaded. Support
such handlers in the gpiochip irqchip helpers by flagging IRQs
as threaded if the .can_sleep property of the gpiochip is
true.
Helpfully deny registration of chained IRQ handlers if the
.can_sleep property is set, as such chips will invariably need
a nested handler rather than a chained handler.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During irq mapping, in irq_set_chip_and_handler() the process
of setting this up may incur calls to lock the irqchip, which
in turn may need to dereference and use the chip data. So set
the data first, then set the chip and handler.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using the irqchip helper inside the gpiolib, make sure
the IRQs are unmapped/disposed before the irqdomain is removed
as part of removing the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a function gpiochip_irqchip_add() to set
up an irqchip for a GPIO controller, and a function
gpiochip_set_chained_irqchip() to chain it to a parent
irqchip.
Most GPIOs are of the type where a number of lines form
a cascaded interrupt controller chained onto
the primary system interrupt controller (or further down the
chain) so let's add this helper and factor the code to
request the lines to be used as IRQs, the .to_irq() function
and the irqdomain into the core as well.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nothing prevents GPIO drivers from returning values outside the
boolean range, and as it turns out a few drivers are actually doing so.
These values were passed as-is to unsuspecting consumers and created
confusion.
This patch makes the internal _gpiod_get_raw_value() function return a
bool, effectively clamping the GPIO value to the boolean range no
matter what the driver does.
While we are at it, we also change the value parameter of
_gpiod_set_raw_value() to bool type before drivers start doing funny
things with it as well.
Another way to fix this would be to change the prototypes of the driver
interface to use bool directly, but this would require a huge
cross-systems patch so this simpler solution is preferred.
Changes since v1:
- Change local variable type to bool as well, use boolean values in
code
- Also change prototype of open drain/open source setting functions
since they are only called from _gpiod_set_raw_value()
This probably calls for a larger booleanization of gpiolib, but let's
keep that for a latter change - right now we need to address the issue
of non-boolean values returned by drivers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current ACPI GPIO event handling code was never tested against real
hardware with functioning GPIO triggered events (at the time such hardware
wasn't available). Thus it misses certain things like requesting the GPIOs
properly, passing correct flags to the interrupt handler and so on.
This patch reworks ACPI GPIO event handling so that we:
1) Use struct acpi_gpio_event for all GPIO signaled events.
2) Switch to use GPIO descriptor API and request GPIOs by calling
gpiochip_request_own_desc() that we added in a previous patch.
3) Pass proper flags from ACPI GPIO resource to request_threaded_irq().
Also instead of open-coding the _AEI iteration loop we can use
acpi_walk_resources(). This simplifies the code a bit and fixes memory leak
that was caused by missing kfree() for buffer returned by
acpi_get_event_resources().
Since the remove path now calls gpiochip_free_own_desc() which takes GPIO
spinlock we need to call acpi_gpiochip_remove() outside of that lock
(analogous to acpi_gpiochip_add() path where the lock is released before
those funtions are called).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometimes it is useful to allow GPIO chips themselves to request GPIOs they
own through gpiolib API. One use case is ACPI ASL code that should be able
to toggle GPIOs through GPIO operation regions.
We can't use gpio_request() because it will pin the module to the kernel
forever (it calls try_module_get()). To solve this we move module refcount
manipulation to gpiod_request() and let __gpiod_request() handle the actual
request. This changes the sequence a bit as now try_module_get() is called
outside of gpio_lock (I think this is safe, try_module_get() handles
serialization it needs already).
Then we provide gpiolib internal functions gpiochip_request/free_own_desc()
that do the same as gpio_request() but don't manipulate module refrence
count. This allows the GPIO chip driver to request and free descriptors it
owns without being pinned to the kernel forever.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is currently debated where the functions to lock a certain
GPIO line as used for IRQs should be called. Delete all
misleading documentation.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers dealing with a gpio_chip might need to act on its
descriptors directly; one example is pinctrl drivers that need to lock a
GPIO for being used as IRQ using gpiod_lock_as_irq().
This patch exports a gpiochip_get_desc() function that returns the
GPIO descriptor at the requested index. It also sweeps the
gpio_to_chip() function out of the consumer interface since any holder
of a gpio_chip reference can manipulate its GPIOs way beyond what a
consumer should be allowed to do.
As a result, gpio_chip is not visible anymore to simple GPIO consumers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The documentation was not clear about whether
gpio_direction_output should take a logical value or the physical
level on the output line, i.e. whether the ACTIVE_LOW status
would be taken into account.
This converts gpiod_direction_output to use the logical level
and adds a new gpiod_direction_output_raw for the raw value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJS3i/MAAoJEEEQszewGV1zVB8P/Rjzgx8To0gQPn49M4u/A1Mk
mAzpUoKa05ILTKBm/bpWPYZPpg9PDqUxOYPsIDEAkc70BKMPTXxrYiE+LSfIzwaJ
a8IRwOzNL7Iwc+zPNS/GrmRJyxymb4lmMD/fypk/YaumZ6j4Hbo+9R8Zct9gbZ5Q
ZbKtz6kLhbkbNCc71bVMgk6yacSBx1ak8Xpd12HlW85NgOCoBj7/DI1Lb61x1ImY
NYpSpmtfGGTkQLtBl5dTLefZOvL1dKSct9TMOsA2jzNqf3zA1YA6XOxPGHK/qtjq
3s9cN1sIVF/g7sm1+qoKXe0OTQrXHT7SX8BH9/tb3MiKO8ItactlQUJlYNR3WFSN
zm1PNe5zWr+GWzV0iUrqoMN4XX8nThiFDOxZpOwBTZcUD6qtDFIZp41M3qxwFTbJ
hCtSQ8gUO1Ce+xtOQYYOwEkRS7FZa1Z+p/lendTFuGDh6DcXy97SrKkTktM4Q98B
LhqrwUzCdES0ecNDi2+P5y4Fc7M0cMMn9SnFvbSBObLB89TF9uzMIn8jUBCZMvrM
eAeZlRBYk8F+6F12higaWqZyiBKIEubXo/Z8T0L2KEDm/z/ddJvhQgBKvWlf3rqi
RToD446rda+RhFBnxLZ3mTui5nZ2WyKTOqhVqeBuriJhE/cTUaQHUBUrbOwx20kE
Xb9mQ2n3GRk2157n1CLY
=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
Now that all users of acpi_gpio.h have been moved to use either the GPIO
descriptor interface or to the internal gpiolib.h we can get rid of
acpi_gpio.h entirely.
Once this is done the only interface to get GPIOs to drivers enumerated
from ACPI namespace is the descriptor based interface.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some devices drivers make use of optional GPIO parameters. For such
drivers, it is important to discriminate between the case where no
GPIO mapping has been defined for the function they are requesting, and
the case where a mapping exists but an error occured while resolving it
or when acquiring the GPIO.
This patch changes the family of gpiod_get() functions such that they
will return -ENOENT if and only if no GPIO mapping is defined for the
requested function. Other error codes are used when an actual error
occured during the GPIO resolution.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/sysfs_elem_dir/kernfs_elem_dir/
* s/sysfs_elem_symlink/kernfs_elem_symlink/
* s/sysfs_elem_attr/kernfs_elem_file/
* s/sysfs_dirent/kernfs_node/
* s/sd/kn/ in kernfs proper
* s/parent_sd/parent/
* s/target_sd/target/
* s/dir_sd/parent/
* s/to_sysfs_dirent()/rb_to_kn()/
* misc renames of local vars when they conflict with the above
Because md, mic and gpio dig into sysfs details, this patch ends up
modifying them. All are sysfs_dirent renames and trivial. While we
can avoid these by introducing a dummy wrapping struct sysfs_dirent
around kernfs_node, given the limited usage outside kernfs and sysfs
proper, I don't think such workaround is called for.
This patch is strictly rename only and doesn't introduce any
functional difference.
- mic / gpio renames were missing. Spotted by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch just accents that @dev could be NULL.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij
Markus Pargmann
Rafael J. Wysocki
Bjorn Andersson
Linus Torvalds
Grygorii Strashko
Rabin Vincent
Tomeu Vizoso
Rob Herring
Masahiro Yamada
Shobhit Kumar
Thomas Gleixner
Uwe Kleine-König
Alexander Sverdlin
Daniel Lockyer
Rojhalat Ibrahim
Colin Cronin
Dmitry Eremin-Solenikov
Johan Hovold
Benoit Parrot
Olliver Schinagl
Alexandre Courbot
Geert Uytterhoeven
Mika Westerberg
Octavian Purdila
Jarkko Nikula
Adrian Hunter
Alexander Shiyan
abdoulaye berthe
Guenter Roeck
Tony Lindgren
Thierry Reding
Rahul Bedarkar
Philipp Zabel
Tejun Heo
Andy Shevchenko