79 строки
2.9 KiB
ReStructuredText
79 строки
2.9 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
|
|
Kernel driver intel-m10-bmc-hwmon
|
|
=================================
|
|
|
|
Supported chips:
|
|
|
|
* Intel MAX 10 BMC for Intel PAC N3000
|
|
|
|
Prefix: 'n3000bmc-hwmon'
|
|
|
|
Author: Xu Yilun <yilun.xu@intel.com>
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver adds the temperature, voltage, current and power reading
|
|
support for the Intel MAX 10 Board Management Controller (BMC) chip.
|
|
The BMC chip is integrated in some Intel Programmable Acceleration
|
|
Cards (PAC). It connects to a set of sensor chips to monitor the
|
|
sensor data of different components on the board. The BMC firmware is
|
|
responsible for sensor data sampling and recording in shared
|
|
registers. The host driver reads the sensor data from these shared
|
|
registers and exposes them to users as hwmon interfaces.
|
|
|
|
The BMC chip is implemented using the Intel MAX 10 CPLD. It could be
|
|
reprogramed to some variants in order to support different Intel
|
|
PACs. The driver is designed to be able to distinguish between the
|
|
variants, but now it only supports the BMC for Intel PAC N3000.
|
|
|
|
|
|
Sysfs attributes
|
|
----------------
|
|
|
|
The following attributes are supported:
|
|
|
|
- Intel MAX 10 BMC for Intel PAC N3000:
|
|
|
|
======================= =======================================================
|
|
tempX_input Temperature of the component (specified by tempX_label)
|
|
tempX_max Temperature maximum setpoint of the component
|
|
tempX_crit Temperature critical setpoint of the component
|
|
tempX_max_hyst Hysteresis for temperature maximum of the component
|
|
tempX_crit_hyst Hysteresis for temperature critical of the component
|
|
temp1_label "Board Temperature"
|
|
temp2_label "FPGA Die Temperature"
|
|
temp3_label "QSFP0 Temperature"
|
|
temp4_label "QSFP1 Temperature"
|
|
temp5_label "Retimer A Temperature"
|
|
temp6_label "Retimer A SerDes Temperature"
|
|
temp7_label "Retimer B Temperature"
|
|
temp8_label "Retimer B SerDes Temperature"
|
|
|
|
inX_input Measured voltage of the component (specified by
|
|
inX_label)
|
|
in0_label "QSFP0 Supply Voltage"
|
|
in1_label "QSFP1 Supply Voltage"
|
|
in2_label "FPGA Core Voltage"
|
|
in3_label "12V Backplane Voltage"
|
|
in4_label "1.2V Voltage"
|
|
in5_label "12V AUX Voltage"
|
|
in6_label "1.8V Voltage"
|
|
in7_label "3.3V Voltage"
|
|
|
|
currX_input Measured current of the component (specified by
|
|
currX_label)
|
|
curr1_label "FPGA Core Current"
|
|
curr2_label "12V Backplane Current"
|
|
curr3_label "12V AUX Current"
|
|
|
|
powerX_input Measured power of the component (specified by
|
|
powerX_label)
|
|
power1_label "Board Power"
|
|
|
|
======================= =======================================================
|
|
|
|
All the attributes are read-only.
|