283 строки
8.8 KiB
C
283 строки
8.8 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
#ifndef _IP22_ZILOG_H
|
|
#define _IP22_ZILOG_H
|
|
|
|
#include <asm/byteorder.h>
|
|
|
|
struct zilog_channel {
|
|
#ifdef __BIG_ENDIAN
|
|
volatile unsigned char unused0[3];
|
|
volatile unsigned char control;
|
|
volatile unsigned char unused1[3];
|
|
volatile unsigned char data;
|
|
#else /* __LITTLE_ENDIAN */
|
|
volatile unsigned char control;
|
|
volatile unsigned char unused0[3];
|
|
volatile unsigned char data;
|
|
volatile unsigned char unused1[3];
|
|
#endif
|
|
};
|
|
|
|
struct zilog_layout {
|
|
struct zilog_channel channelB;
|
|
struct zilog_channel channelA;
|
|
};
|
|
|
|
#define NUM_ZSREGS 16
|
|
|
|
/* Conversion routines to/from brg time constants from/to bits
|
|
* per second.
|
|
*/
|
|
#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
|
|
#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
|
|
|
|
/* The Zilog register set */
|
|
|
|
#define FLAG 0x7e
|
|
|
|
/* Write Register 0 */
|
|
#define R0 0 /* Register selects */
|
|
#define R1 1
|
|
#define R2 2
|
|
#define R3 3
|
|
#define R4 4
|
|
#define R5 5
|
|
#define R6 6
|
|
#define R7 7
|
|
#define R8 8
|
|
#define R9 9
|
|
#define R10 10
|
|
#define R11 11
|
|
#define R12 12
|
|
#define R13 13
|
|
#define R14 14
|
|
#define R15 15
|
|
|
|
#define NULLCODE 0 /* Null Code */
|
|
#define POINT_HIGH 0x8 /* Select upper half of registers */
|
|
#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
|
|
#define SEND_ABORT 0x18 /* HDLC Abort */
|
|
#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
|
|
#define RES_Tx_P 0x28 /* Reset TxINT Pending */
|
|
#define ERR_RES 0x30 /* Error Reset */
|
|
#define RES_H_IUS 0x38 /* Reset highest IUS */
|
|
|
|
#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
|
|
#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
|
|
#define RES_EOM_L 0xC0 /* Reset EOM latch */
|
|
|
|
/* Write Register 1 */
|
|
|
|
#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
|
|
#define TxINT_ENAB 0x2 /* Tx Int Enable */
|
|
#define PAR_SPEC 0x4 /* Parity is special condition */
|
|
|
|
#define RxINT_DISAB 0 /* Rx Int Disable */
|
|
#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
|
|
#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
|
|
#define INT_ERR_Rx 0x18 /* Int on error only */
|
|
#define RxINT_MASK 0x18
|
|
|
|
#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
|
|
#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
|
|
#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
|
|
|
|
/* Write Register #2 (Interrupt Vector) */
|
|
|
|
/* Write Register 3 */
|
|
|
|
#define RxENAB 0x1 /* Rx Enable */
|
|
#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
|
|
#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
|
|
#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
|
|
#define ENT_HM 0x10 /* Enter Hunt Mode */
|
|
#define AUTO_ENAB 0x20 /* Auto Enables */
|
|
#define Rx5 0x0 /* Rx 5 Bits/Character */
|
|
#define Rx7 0x40 /* Rx 7 Bits/Character */
|
|
#define Rx6 0x80 /* Rx 6 Bits/Character */
|
|
#define Rx8 0xc0 /* Rx 8 Bits/Character */
|
|
#define RxN_MASK 0xc0
|
|
|
|
/* Write Register 4 */
|
|
|
|
#define PAR_ENAB 0x1 /* Parity Enable */
|
|
#define PAR_EVEN 0x2 /* Parity Even/Odd* */
|
|
|
|
#define SYNC_ENAB 0 /* Sync Modes Enable */
|
|
#define SB1 0x4 /* 1 stop bit/char */
|
|
#define SB15 0x8 /* 1.5 stop bits/char */
|
|
#define SB2 0xc /* 2 stop bits/char */
|
|
|
|
#define MONSYNC 0 /* 8 Bit Sync character */
|
|
#define BISYNC 0x10 /* 16 bit sync character */
|
|
#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
|
|
#define EXTSYNC 0x30 /* External Sync Mode */
|
|
|
|
#define X1CLK 0x0 /* x1 clock mode */
|
|
#define X16CLK 0x40 /* x16 clock mode */
|
|
#define X32CLK 0x80 /* x32 clock mode */
|
|
#define X64CLK 0xC0 /* x64 clock mode */
|
|
#define XCLK_MASK 0xC0
|
|
|
|
/* Write Register 5 */
|
|
|
|
#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
|
|
#define RTS 0x2 /* RTS */
|
|
#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
|
|
#define TxENAB 0x8 /* Tx Enable */
|
|
#define SND_BRK 0x10 /* Send Break */
|
|
#define Tx5 0x0 /* Tx 5 bits (or less)/character */
|
|
#define Tx7 0x20 /* Tx 7 bits/character */
|
|
#define Tx6 0x40 /* Tx 6 bits/character */
|
|
#define Tx8 0x60 /* Tx 8 bits/character */
|
|
#define TxN_MASK 0x60
|
|
#define DTR 0x80 /* DTR */
|
|
|
|
/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
|
|
|
|
/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
|
|
|
|
/* Write Register 8 (transmit buffer) */
|
|
|
|
/* Write Register 9 (Master interrupt control) */
|
|
#define VIS 1 /* Vector Includes Status */
|
|
#define NV 2 /* No Vector */
|
|
#define DLC 4 /* Disable Lower Chain */
|
|
#define MIE 8 /* Master Interrupt Enable */
|
|
#define STATHI 0x10 /* Status high */
|
|
#define NORESET 0 /* No reset on write to R9 */
|
|
#define CHRB 0x40 /* Reset channel B */
|
|
#define CHRA 0x80 /* Reset channel A */
|
|
#define FHWRES 0xc0 /* Force hardware reset */
|
|
|
|
/* Write Register 10 (misc control bits) */
|
|
#define BIT6 1 /* 6 bit/8bit sync */
|
|
#define LOOPMODE 2 /* SDLC Loop mode */
|
|
#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
|
|
#define MARKIDLE 8 /* Mark/flag on idle */
|
|
#define GAOP 0x10 /* Go active on poll */
|
|
#define NRZ 0 /* NRZ mode */
|
|
#define NRZI 0x20 /* NRZI mode */
|
|
#define FM1 0x40 /* FM1 (transition = 1) */
|
|
#define FM0 0x60 /* FM0 (transition = 0) */
|
|
#define CRCPS 0x80 /* CRC Preset I/O */
|
|
|
|
/* Write Register 11 (Clock Mode control) */
|
|
#define TRxCXT 0 /* TRxC = Xtal output */
|
|
#define TRxCTC 1 /* TRxC = Transmit clock */
|
|
#define TRxCBR 2 /* TRxC = BR Generator Output */
|
|
#define TRxCDP 3 /* TRxC = DPLL output */
|
|
#define TRxCOI 4 /* TRxC O/I */
|
|
#define TCRTxCP 0 /* Transmit clock = RTxC pin */
|
|
#define TCTRxCP 8 /* Transmit clock = TRxC pin */
|
|
#define TCBR 0x10 /* Transmit clock = BR Generator output */
|
|
#define TCDPLL 0x18 /* Transmit clock = DPLL output */
|
|
#define RCRTxCP 0 /* Receive clock = RTxC pin */
|
|
#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
|
|
#define RCBR 0x40 /* Receive clock = BR Generator output */
|
|
#define RCDPLL 0x60 /* Receive clock = DPLL output */
|
|
#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
|
|
|
|
/* Write Register 12 (lower byte of baud rate generator time constant) */
|
|
|
|
/* Write Register 13 (upper byte of baud rate generator time constant) */
|
|
|
|
/* Write Register 14 (Misc control bits) */
|
|
#define BRENAB 1 /* Baud rate generator enable */
|
|
#define BRSRC 2 /* Baud rate generator source */
|
|
#define DTRREQ 4 /* DTR/Request function */
|
|
#define AUTOECHO 8 /* Auto Echo */
|
|
#define LOOPBAK 0x10 /* Local loopback */
|
|
#define SEARCH 0x20 /* Enter search mode */
|
|
#define RMC 0x40 /* Reset missing clock */
|
|
#define DISDPLL 0x60 /* Disable DPLL */
|
|
#define SSBR 0x80 /* Set DPLL source = BR generator */
|
|
#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
|
|
#define SFMM 0xc0 /* Set FM mode */
|
|
#define SNRZI 0xe0 /* Set NRZI mode */
|
|
|
|
/* Write Register 15 (external/status interrupt control) */
|
|
#define ZCIE 2 /* Zero count IE */
|
|
#define DCDIE 8 /* DCD IE */
|
|
#define SYNCIE 0x10 /* Sync/hunt IE */
|
|
#define CTSIE 0x20 /* CTS IE */
|
|
#define TxUIE 0x40 /* Tx Underrun/EOM IE */
|
|
#define BRKIE 0x80 /* Break/Abort IE */
|
|
|
|
|
|
/* Read Register 0 */
|
|
#define Rx_CH_AV 0x1 /* Rx Character Available */
|
|
#define ZCOUNT 0x2 /* Zero count */
|
|
#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
|
|
#define DCD 0x8 /* DCD */
|
|
#define SYNC 0x10 /* Sync/hunt */
|
|
#define CTS 0x20 /* CTS */
|
|
#define TxEOM 0x40 /* Tx underrun */
|
|
#define BRK_ABRT 0x80 /* Break/Abort */
|
|
|
|
/* Read Register 1 */
|
|
#define ALL_SNT 0x1 /* All sent */
|
|
/* Residue Data for 8 Rx bits/char programmed */
|
|
#define RES3 0x8 /* 0/3 */
|
|
#define RES4 0x4 /* 0/4 */
|
|
#define RES5 0xc /* 0/5 */
|
|
#define RES6 0x2 /* 0/6 */
|
|
#define RES7 0xa /* 0/7 */
|
|
#define RES8 0x6 /* 0/8 */
|
|
#define RES18 0xe /* 1/8 */
|
|
#define RES28 0x0 /* 2/8 */
|
|
/* Special Rx Condition Interrupts */
|
|
#define PAR_ERR 0x10 /* Parity error */
|
|
#define Rx_OVR 0x20 /* Rx Overrun Error */
|
|
#define CRC_ERR 0x40 /* CRC/Framing Error */
|
|
#define END_FR 0x80 /* End of Frame (SDLC) */
|
|
|
|
/* Read Register 2 (channel b only) - Interrupt vector */
|
|
#define CHB_Tx_EMPTY 0x00
|
|
#define CHB_EXT_STAT 0x02
|
|
#define CHB_Rx_AVAIL 0x04
|
|
#define CHB_SPECIAL 0x06
|
|
#define CHA_Tx_EMPTY 0x08
|
|
#define CHA_EXT_STAT 0x0a
|
|
#define CHA_Rx_AVAIL 0x0c
|
|
#define CHA_SPECIAL 0x0e
|
|
#define STATUS_MASK 0x0e
|
|
|
|
/* Read Register 3 (interrupt pending register) ch a only */
|
|
#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
|
|
#define CHBTxIP 0x2 /* Channel B Tx IP */
|
|
#define CHBRxIP 0x4 /* Channel B Rx IP */
|
|
#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
|
|
#define CHATxIP 0x10 /* Channel A Tx IP */
|
|
#define CHARxIP 0x20 /* Channel A Rx IP */
|
|
|
|
/* Read Register 8 (receive data register) */
|
|
|
|
/* Read Register 10 (misc status bits) */
|
|
#define ONLOOP 2 /* On loop */
|
|
#define LOOPSEND 0x10 /* Loop sending */
|
|
#define CLK2MIS 0x40 /* Two clocks missing */
|
|
#define CLK1MIS 0x80 /* One clock missing */
|
|
|
|
/* Read Register 12 (lower byte of baud rate generator constant) */
|
|
|
|
/* Read Register 13 (upper byte of baud rate generator constant) */
|
|
|
|
/* Read Register 15 (value of WR 15) */
|
|
|
|
/* Misc macros */
|
|
#define ZS_CLEARERR(channel) do { writeb(ERR_RES, &channel->control); \
|
|
udelay(5); } while(0)
|
|
|
|
#define ZS_CLEARSTAT(channel) do { writeb(RES_EXT_INT, &channel->control); \
|
|
udelay(5); } while(0)
|
|
|
|
#define ZS_CLEARFIFO(channel) do { readb(&channel->data); \
|
|
udelay(2); \
|
|
readb(&channel->data); \
|
|
udelay(2); \
|
|
readb(&channel->data); \
|
|
udelay(2); } while(0)
|
|
|
|
#endif /* _IP22_ZILOG_H */
|