1084 строки
29 KiB
C
1084 строки
29 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Copyright (c) 2020 Linaro Limited
|
|
*
|
|
* Based on original driver:
|
|
* Copyright (c) 2012-2020, The Linux Foundation. All rights reserved.
|
|
*
|
|
* Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
#include <linux/bitfield.h>
|
|
#include <linux/iio/adc/qcom-vadc-common.h>
|
|
#include <linux/iio/consumer.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/thermal.h>
|
|
#include <asm-generic/unaligned.h>
|
|
|
|
#include "../thermal_hwmon.h"
|
|
|
|
/*
|
|
* Thermal monitoring block consists of 8 (ADC_TM5_NUM_CHANNELS) channels. Each
|
|
* channel is programmed to use one of ADC channels for voltage comparison.
|
|
* Voltages are programmed using ADC codes, so we have to convert temp to
|
|
* voltage and then to ADC code value.
|
|
*
|
|
* Configuration of TM channels must match configuration of corresponding ADC
|
|
* channels.
|
|
*/
|
|
|
|
#define ADC5_MAX_CHANNEL 0xc0
|
|
#define ADC_TM5_NUM_CHANNELS 8
|
|
|
|
#define ADC_TM5_STATUS_LOW 0x0a
|
|
|
|
#define ADC_TM5_STATUS_HIGH 0x0b
|
|
|
|
#define ADC_TM5_NUM_BTM 0x0f
|
|
|
|
#define ADC_TM5_ADC_DIG_PARAM 0x42
|
|
|
|
#define ADC_TM5_FAST_AVG_CTL (ADC_TM5_ADC_DIG_PARAM + 1)
|
|
#define ADC_TM5_FAST_AVG_EN BIT(7)
|
|
|
|
#define ADC_TM5_MEAS_INTERVAL_CTL (ADC_TM5_ADC_DIG_PARAM + 2)
|
|
#define ADC_TM5_TIMER1 3 /* 3.9ms */
|
|
|
|
#define ADC_TM5_MEAS_INTERVAL_CTL2 (ADC_TM5_ADC_DIG_PARAM + 3)
|
|
#define ADC_TM5_MEAS_INTERVAL_CTL2_MASK 0xf0
|
|
#define ADC_TM5_TIMER2 10 /* 1 second */
|
|
#define ADC_TM5_MEAS_INTERVAL_CTL3_MASK 0xf
|
|
#define ADC_TM5_TIMER3 4 /* 4 second */
|
|
|
|
#define ADC_TM_EN_CTL1 0x46
|
|
#define ADC_TM_EN BIT(7)
|
|
#define ADC_TM_CONV_REQ 0x47
|
|
#define ADC_TM_CONV_REQ_EN BIT(7)
|
|
|
|
#define ADC_TM5_M_CHAN_BASE 0x60
|
|
|
|
#define ADC_TM5_M_ADC_CH_SEL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 0)
|
|
#define ADC_TM5_M_LOW_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 1)
|
|
#define ADC_TM5_M_LOW_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 2)
|
|
#define ADC_TM5_M_HIGH_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 3)
|
|
#define ADC_TM5_M_HIGH_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 4)
|
|
#define ADC_TM5_M_MEAS_INTERVAL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 5)
|
|
#define ADC_TM5_M_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 6)
|
|
#define ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK 0xf
|
|
#define ADC_TM5_M_CTL_CAL_SEL_MASK 0x30
|
|
#define ADC_TM5_M_CTL_CAL_VAL 0x40
|
|
#define ADC_TM5_M_EN(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 7)
|
|
#define ADC_TM5_M_MEAS_EN BIT(7)
|
|
#define ADC_TM5_M_HIGH_THR_INT_EN BIT(1)
|
|
#define ADC_TM5_M_LOW_THR_INT_EN BIT(0)
|
|
|
|
#define ADC_TM_GEN2_STATUS1 0x08
|
|
#define ADC_TM_GEN2_STATUS_LOW_SET 0x09
|
|
#define ADC_TM_GEN2_STATUS_LOW_CLR 0x0a
|
|
#define ADC_TM_GEN2_STATUS_HIGH_SET 0x0b
|
|
#define ADC_TM_GEN2_STATUS_HIGH_CLR 0x0c
|
|
|
|
#define ADC_TM_GEN2_CFG_HS_SET 0x0d
|
|
#define ADC_TM_GEN2_CFG_HS_FLAG BIT(0)
|
|
#define ADC_TM_GEN2_CFG_HS_CLR 0x0e
|
|
|
|
#define ADC_TM_GEN2_SID 0x40
|
|
|
|
#define ADC_TM_GEN2_CH_CTL 0x41
|
|
#define ADC_TM_GEN2_TM_CH_SEL GENMASK(7, 5)
|
|
#define ADC_TM_GEN2_MEAS_INT_SEL GENMASK(3, 2)
|
|
|
|
#define ADC_TM_GEN2_ADC_DIG_PARAM 0x42
|
|
#define ADC_TM_GEN2_CTL_CAL_SEL GENMASK(5, 4)
|
|
#define ADC_TM_GEN2_CTL_DEC_RATIO_MASK GENMASK(3, 2)
|
|
|
|
#define ADC_TM_GEN2_FAST_AVG_CTL 0x43
|
|
#define ADC_TM_GEN2_FAST_AVG_EN BIT(7)
|
|
|
|
#define ADC_TM_GEN2_ADC_CH_SEL_CTL 0x44
|
|
|
|
#define ADC_TM_GEN2_DELAY_CTL 0x45
|
|
#define ADC_TM_GEN2_HW_SETTLE_DELAY GENMASK(3, 0)
|
|
|
|
#define ADC_TM_GEN2_EN_CTL1 0x46
|
|
#define ADC_TM_GEN2_EN BIT(7)
|
|
|
|
#define ADC_TM_GEN2_CONV_REQ 0x47
|
|
#define ADC_TM_GEN2_CONV_REQ_EN BIT(7)
|
|
|
|
#define ADC_TM_GEN2_LOW_THR0 0x49
|
|
#define ADC_TM_GEN2_LOW_THR1 0x4a
|
|
#define ADC_TM_GEN2_HIGH_THR0 0x4b
|
|
#define ADC_TM_GEN2_HIGH_THR1 0x4c
|
|
#define ADC_TM_GEN2_LOWER_MASK(n) ((n) & GENMASK(7, 0))
|
|
#define ADC_TM_GEN2_UPPER_MASK(n) (((n) & GENMASK(15, 8)) >> 8)
|
|
|
|
#define ADC_TM_GEN2_MEAS_IRQ_EN 0x4d
|
|
#define ADC_TM_GEN2_MEAS_EN BIT(7)
|
|
#define ADC_TM5_GEN2_HIGH_THR_INT_EN BIT(1)
|
|
#define ADC_TM5_GEN2_LOW_THR_INT_EN BIT(0)
|
|
|
|
#define ADC_TM_GEN2_MEAS_INT_LSB 0x50
|
|
#define ADC_TM_GEN2_MEAS_INT_MSB 0x51
|
|
#define ADC_TM_GEN2_MEAS_INT_MODE 0x52
|
|
|
|
#define ADC_TM_GEN2_Mn_DATA0(n) ((n * 2) + 0xa0)
|
|
#define ADC_TM_GEN2_Mn_DATA1(n) ((n * 2) + 0xa1)
|
|
#define ADC_TM_GEN2_DATA_SHIFT 8
|
|
|
|
enum adc5_timer_select {
|
|
ADC5_TIMER_SEL_1 = 0,
|
|
ADC5_TIMER_SEL_2,
|
|
ADC5_TIMER_SEL_3,
|
|
ADC5_TIMER_SEL_NONE,
|
|
};
|
|
|
|
enum adc5_gen {
|
|
ADC_TM5,
|
|
ADC_TM_HC,
|
|
ADC_TM5_GEN2,
|
|
ADC_TM5_MAX
|
|
};
|
|
|
|
enum adc_tm5_cal_method {
|
|
ADC_TM5_NO_CAL = 0,
|
|
ADC_TM5_RATIOMETRIC_CAL,
|
|
ADC_TM5_ABSOLUTE_CAL
|
|
};
|
|
|
|
enum adc_tm_gen2_time_select {
|
|
MEAS_INT_50MS = 0,
|
|
MEAS_INT_100MS,
|
|
MEAS_INT_1S,
|
|
MEAS_INT_SET,
|
|
MEAS_INT_NONE,
|
|
};
|
|
|
|
struct adc_tm5_chip;
|
|
struct adc_tm5_channel;
|
|
|
|
struct adc_tm5_data {
|
|
const u32 full_scale_code_volt;
|
|
unsigned int *decimation;
|
|
unsigned int *hw_settle;
|
|
int (*disable_channel)(struct adc_tm5_channel *channel);
|
|
int (*configure)(struct adc_tm5_channel *channel, int low, int high);
|
|
irqreturn_t (*isr)(int irq, void *data);
|
|
int (*init)(struct adc_tm5_chip *chip);
|
|
char *irq_name;
|
|
int gen;
|
|
};
|
|
|
|
/**
|
|
* struct adc_tm5_channel - ADC Thermal Monitoring channel data.
|
|
* @channel: channel number.
|
|
* @adc_channel: corresponding ADC channel number.
|
|
* @cal_method: calibration method.
|
|
* @prescale: channel scaling performed on the input signal.
|
|
* @hw_settle_time: the time between AMUX being configured and the
|
|
* start of conversion.
|
|
* @decimation: sampling rate supported for the channel.
|
|
* @avg_samples: ability to provide single result from the ADC
|
|
* that is an average of multiple measurements.
|
|
* @high_thr_en: channel upper voltage threshold enable state.
|
|
* @low_thr_en: channel lower voltage threshold enable state.
|
|
* @meas_en: recurring measurement enable state
|
|
* @iio: IIO channel instance used by this channel.
|
|
* @chip: ADC TM chip instance.
|
|
* @tzd: thermal zone device used by this channel.
|
|
*/
|
|
struct adc_tm5_channel {
|
|
unsigned int channel;
|
|
unsigned int adc_channel;
|
|
enum adc_tm5_cal_method cal_method;
|
|
unsigned int prescale;
|
|
unsigned int hw_settle_time;
|
|
unsigned int decimation; /* For Gen2 ADC_TM */
|
|
unsigned int avg_samples; /* For Gen2 ADC_TM */
|
|
bool high_thr_en; /* For Gen2 ADC_TM */
|
|
bool low_thr_en; /* For Gen2 ADC_TM */
|
|
bool meas_en; /* For Gen2 ADC_TM */
|
|
struct iio_channel *iio;
|
|
struct adc_tm5_chip *chip;
|
|
struct thermal_zone_device *tzd;
|
|
};
|
|
|
|
/**
|
|
* struct adc_tm5_chip - ADC Thermal Monitoring properties
|
|
* @regmap: SPMI ADC5 Thermal Monitoring peripheral register map field.
|
|
* @dev: SPMI ADC5 device.
|
|
* @data: software configuration data.
|
|
* @channels: array of ADC TM channel data.
|
|
* @nchannels: amount of channels defined/allocated
|
|
* @decimation: sampling rate supported for the channel.
|
|
* Applies to all channels, used only on Gen1 ADC_TM.
|
|
* @avg_samples: ability to provide single result from the ADC
|
|
* that is an average of multiple measurements. Applies to all
|
|
* channels, used only on Gen1 ADC_TM.
|
|
* @base: base address of TM registers.
|
|
* @adc_mutex_lock: ADC_TM mutex lock, used only on Gen2 ADC_TM.
|
|
* It is used to ensure only one ADC channel configuration
|
|
* is done at a time using the shared set of configuration
|
|
* registers.
|
|
*/
|
|
struct adc_tm5_chip {
|
|
struct regmap *regmap;
|
|
struct device *dev;
|
|
const struct adc_tm5_data *data;
|
|
struct adc_tm5_channel *channels;
|
|
unsigned int nchannels;
|
|
unsigned int decimation;
|
|
unsigned int avg_samples;
|
|
u16 base;
|
|
struct mutex adc_mutex_lock;
|
|
};
|
|
|
|
static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
|
|
{
|
|
return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len);
|
|
}
|
|
|
|
static int adc_tm5_write(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
|
|
{
|
|
return regmap_bulk_write(adc_tm->regmap, adc_tm->base + offset, data, len);
|
|
}
|
|
|
|
static int adc_tm5_reg_update(struct adc_tm5_chip *adc_tm, u16 offset, u8 mask, u8 val)
|
|
{
|
|
return regmap_write_bits(adc_tm->regmap, adc_tm->base + offset, mask, val);
|
|
}
|
|
|
|
static irqreturn_t adc_tm5_isr(int irq, void *data)
|
|
{
|
|
struct adc_tm5_chip *chip = data;
|
|
u8 status_low, status_high, ctl;
|
|
int ret, i;
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM5_STATUS_LOW, &status_low, sizeof(status_low));
|
|
if (unlikely(ret)) {
|
|
dev_err(chip->dev, "read status low failed: %d\n", ret);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM5_STATUS_HIGH, &status_high, sizeof(status_high));
|
|
if (unlikely(ret)) {
|
|
dev_err(chip->dev, "read status high failed: %d\n", ret);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
for (i = 0; i < chip->nchannels; i++) {
|
|
bool upper_set = false, lower_set = false;
|
|
unsigned int ch = chip->channels[i].channel;
|
|
|
|
/* No TZD, we warned at the boot time */
|
|
if (!chip->channels[i].tzd)
|
|
continue;
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM5_M_EN(ch), &ctl, sizeof(ctl));
|
|
if (unlikely(ret)) {
|
|
dev_err(chip->dev, "ctl read failed: %d, channel %d\n", ret, i);
|
|
continue;
|
|
}
|
|
|
|
if (!(ctl & ADC_TM5_M_MEAS_EN))
|
|
continue;
|
|
|
|
lower_set = (status_low & BIT(ch)) &&
|
|
(ctl & ADC_TM5_M_LOW_THR_INT_EN);
|
|
|
|
upper_set = (status_high & BIT(ch)) &&
|
|
(ctl & ADC_TM5_M_HIGH_THR_INT_EN);
|
|
|
|
if (upper_set || lower_set)
|
|
thermal_zone_device_update(chip->channels[i].tzd,
|
|
THERMAL_EVENT_UNSPECIFIED);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t adc_tm5_gen2_isr(int irq, void *data)
|
|
{
|
|
struct adc_tm5_chip *chip = data;
|
|
u8 status_low, status_high;
|
|
int ret, i;
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM_GEN2_STATUS_LOW_CLR, &status_low, sizeof(status_low));
|
|
if (ret) {
|
|
dev_err(chip->dev, "read status_low failed: %d\n", ret);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM_GEN2_STATUS_HIGH_CLR, &status_high, sizeof(status_high));
|
|
if (ret) {
|
|
dev_err(chip->dev, "read status_high failed: %d\n", ret);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_STATUS_LOW_CLR, &status_low, sizeof(status_low));
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "clear status low failed with %d\n", ret);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_STATUS_HIGH_CLR, &status_high, sizeof(status_high));
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "clear status high failed with %d\n", ret);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
for (i = 0; i < chip->nchannels; i++) {
|
|
bool upper_set = false, lower_set = false;
|
|
unsigned int ch = chip->channels[i].channel;
|
|
|
|
/* No TZD, we warned at the boot time */
|
|
if (!chip->channels[i].tzd)
|
|
continue;
|
|
|
|
if (!chip->channels[i].meas_en)
|
|
continue;
|
|
|
|
lower_set = (status_low & BIT(ch)) &&
|
|
(chip->channels[i].low_thr_en);
|
|
|
|
upper_set = (status_high & BIT(ch)) &&
|
|
(chip->channels[i].high_thr_en);
|
|
|
|
if (upper_set || lower_set)
|
|
thermal_zone_device_update(chip->channels[i].tzd,
|
|
THERMAL_EVENT_UNSPECIFIED);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int adc_tm5_get_temp(void *data, int *temp)
|
|
{
|
|
struct adc_tm5_channel *channel = data;
|
|
int ret;
|
|
|
|
if (!channel || !channel->iio)
|
|
return -EINVAL;
|
|
|
|
ret = iio_read_channel_processed(channel->iio, temp);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (ret != IIO_VAL_INT)
|
|
return -EINVAL;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int adc_tm5_disable_channel(struct adc_tm5_channel *channel)
|
|
{
|
|
struct adc_tm5_chip *chip = channel->chip;
|
|
unsigned int reg = ADC_TM5_M_EN(channel->channel);
|
|
|
|
return adc_tm5_reg_update(chip, reg,
|
|
ADC_TM5_M_MEAS_EN |
|
|
ADC_TM5_M_HIGH_THR_INT_EN |
|
|
ADC_TM5_M_LOW_THR_INT_EN,
|
|
0);
|
|
}
|
|
|
|
#define ADC_TM_GEN2_POLL_DELAY_MIN_US 100
|
|
#define ADC_TM_GEN2_POLL_DELAY_MAX_US 110
|
|
#define ADC_TM_GEN2_POLL_RETRY_COUNT 3
|
|
|
|
static int32_t adc_tm5_gen2_conv_req(struct adc_tm5_chip *chip)
|
|
{
|
|
int ret;
|
|
u8 data;
|
|
unsigned int count;
|
|
|
|
data = ADC_TM_GEN2_EN;
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_EN_CTL1, &data, 1);
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm enable failed with %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
data = ADC_TM_GEN2_CFG_HS_FLAG;
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_CFG_HS_SET, &data, 1);
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm handshake failed with %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
data = ADC_TM_GEN2_CONV_REQ_EN;
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_CONV_REQ, &data, 1);
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm request conversion failed with %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* SW sets a handshake bit and waits for PBS to clear it
|
|
* before the next conversion request can be queued.
|
|
*/
|
|
|
|
for (count = 0; count < ADC_TM_GEN2_POLL_RETRY_COUNT; count++) {
|
|
ret = adc_tm5_read(chip, ADC_TM_GEN2_CFG_HS_SET, &data, sizeof(data));
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm read failed with %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
if (!(data & ADC_TM_GEN2_CFG_HS_FLAG))
|
|
return ret;
|
|
usleep_range(ADC_TM_GEN2_POLL_DELAY_MIN_US,
|
|
ADC_TM_GEN2_POLL_DELAY_MAX_US);
|
|
}
|
|
|
|
dev_err(chip->dev, "adc-tm conversion request handshake timed out\n");
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static int adc_tm5_gen2_disable_channel(struct adc_tm5_channel *channel)
|
|
{
|
|
struct adc_tm5_chip *chip = channel->chip;
|
|
int ret;
|
|
u8 val;
|
|
|
|
mutex_lock(&chip->adc_mutex_lock);
|
|
|
|
channel->meas_en = false;
|
|
channel->high_thr_en = false;
|
|
channel->low_thr_en = false;
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM_GEN2_CH_CTL, &val, sizeof(val));
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm block read failed with %d\n", ret);
|
|
goto disable_fail;
|
|
}
|
|
|
|
val &= ~ADC_TM_GEN2_TM_CH_SEL;
|
|
val |= FIELD_PREP(ADC_TM_GEN2_TM_CH_SEL, channel->channel);
|
|
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_CH_CTL, &val, 1);
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm channel disable failed with %d\n", ret);
|
|
goto disable_fail;
|
|
}
|
|
|
|
val = 0;
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_MEAS_IRQ_EN, &val, 1);
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm interrupt disable failed with %d\n", ret);
|
|
goto disable_fail;
|
|
}
|
|
|
|
|
|
ret = adc_tm5_gen2_conv_req(channel->chip);
|
|
if (ret < 0)
|
|
dev_err(chip->dev, "adc-tm channel configure failed with %d\n", ret);
|
|
|
|
disable_fail:
|
|
mutex_unlock(&chip->adc_mutex_lock);
|
|
return ret;
|
|
}
|
|
|
|
static int adc_tm5_enable(struct adc_tm5_chip *chip)
|
|
{
|
|
int ret;
|
|
u8 data;
|
|
|
|
data = ADC_TM_EN;
|
|
ret = adc_tm5_write(chip, ADC_TM_EN_CTL1, &data, sizeof(data));
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm enable failed\n");
|
|
return ret;
|
|
}
|
|
|
|
data = ADC_TM_CONV_REQ_EN;
|
|
ret = adc_tm5_write(chip, ADC_TM_CONV_REQ, &data, sizeof(data));
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm request conversion failed\n");
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int adc_tm5_configure(struct adc_tm5_channel *channel, int low, int high)
|
|
{
|
|
struct adc_tm5_chip *chip = channel->chip;
|
|
u8 buf[8];
|
|
u16 reg = ADC_TM5_M_ADC_CH_SEL_CTL(channel->channel);
|
|
int ret;
|
|
|
|
ret = adc_tm5_read(chip, reg, buf, sizeof(buf));
|
|
if (ret) {
|
|
dev_err(chip->dev, "channel %d params read failed: %d\n", channel->channel, ret);
|
|
return ret;
|
|
}
|
|
|
|
buf[0] = channel->adc_channel;
|
|
|
|
/* High temperature corresponds to low voltage threshold */
|
|
if (high != INT_MAX) {
|
|
u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
|
|
chip->data->full_scale_code_volt, high);
|
|
|
|
put_unaligned_le16(adc_code, &buf[1]);
|
|
buf[7] |= ADC_TM5_M_LOW_THR_INT_EN;
|
|
} else {
|
|
buf[7] &= ~ADC_TM5_M_LOW_THR_INT_EN;
|
|
}
|
|
|
|
/* Low temperature corresponds to high voltage threshold */
|
|
if (low != -INT_MAX) {
|
|
u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale,
|
|
chip->data->full_scale_code_volt, low);
|
|
|
|
put_unaligned_le16(adc_code, &buf[3]);
|
|
buf[7] |= ADC_TM5_M_HIGH_THR_INT_EN;
|
|
} else {
|
|
buf[7] &= ~ADC_TM5_M_HIGH_THR_INT_EN;
|
|
}
|
|
|
|
buf[5] = ADC5_TIMER_SEL_2;
|
|
|
|
/* Set calibration select, hw_settle delay */
|
|
buf[6] &= ~ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK;
|
|
buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK, channel->hw_settle_time);
|
|
buf[6] &= ~ADC_TM5_M_CTL_CAL_SEL_MASK;
|
|
buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_CAL_SEL_MASK, channel->cal_method);
|
|
|
|
buf[7] |= ADC_TM5_M_MEAS_EN;
|
|
|
|
ret = adc_tm5_write(chip, reg, buf, sizeof(buf));
|
|
if (ret) {
|
|
dev_err(chip->dev, "channel %d params write failed: %d\n", channel->channel, ret);
|
|
return ret;
|
|
}
|
|
|
|
return adc_tm5_enable(chip);
|
|
}
|
|
|
|
static int adc_tm5_gen2_configure(struct adc_tm5_channel *channel, int low, int high)
|
|
{
|
|
struct adc_tm5_chip *chip = channel->chip;
|
|
int ret;
|
|
u8 buf[14];
|
|
u16 adc_code;
|
|
|
|
mutex_lock(&chip->adc_mutex_lock);
|
|
|
|
channel->meas_en = true;
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM_GEN2_SID, buf, sizeof(buf));
|
|
if (ret < 0) {
|
|
dev_err(chip->dev, "adc-tm block read failed with %d\n", ret);
|
|
goto config_fail;
|
|
}
|
|
|
|
/* Set SID from virtual channel number */
|
|
buf[0] = channel->adc_channel >> 8;
|
|
|
|
/* Set TM channel number used and measurement interval */
|
|
buf[1] &= ~ADC_TM_GEN2_TM_CH_SEL;
|
|
buf[1] |= FIELD_PREP(ADC_TM_GEN2_TM_CH_SEL, channel->channel);
|
|
buf[1] &= ~ADC_TM_GEN2_MEAS_INT_SEL;
|
|
buf[1] |= FIELD_PREP(ADC_TM_GEN2_MEAS_INT_SEL, MEAS_INT_1S);
|
|
|
|
buf[2] &= ~ADC_TM_GEN2_CTL_DEC_RATIO_MASK;
|
|
buf[2] |= FIELD_PREP(ADC_TM_GEN2_CTL_DEC_RATIO_MASK, channel->decimation);
|
|
buf[2] &= ~ADC_TM_GEN2_CTL_CAL_SEL;
|
|
buf[2] |= FIELD_PREP(ADC_TM_GEN2_CTL_CAL_SEL, channel->cal_method);
|
|
|
|
buf[3] = channel->avg_samples | ADC_TM_GEN2_FAST_AVG_EN;
|
|
|
|
buf[4] = channel->adc_channel & 0xff;
|
|
|
|
buf[5] = channel->hw_settle_time & ADC_TM_GEN2_HW_SETTLE_DELAY;
|
|
|
|
/* High temperature corresponds to low voltage threshold */
|
|
if (high != INT_MAX) {
|
|
channel->low_thr_en = true;
|
|
adc_code = qcom_adc_tm5_gen2_temp_res_scale(high);
|
|
put_unaligned_le16(adc_code, &buf[9]);
|
|
} else {
|
|
channel->low_thr_en = false;
|
|
}
|
|
|
|
/* Low temperature corresponds to high voltage threshold */
|
|
if (low != -INT_MAX) {
|
|
channel->high_thr_en = true;
|
|
adc_code = qcom_adc_tm5_gen2_temp_res_scale(low);
|
|
put_unaligned_le16(adc_code, &buf[11]);
|
|
} else {
|
|
channel->high_thr_en = false;
|
|
}
|
|
|
|
buf[13] = ADC_TM_GEN2_MEAS_EN;
|
|
if (channel->high_thr_en)
|
|
buf[13] |= ADC_TM5_GEN2_HIGH_THR_INT_EN;
|
|
if (channel->low_thr_en)
|
|
buf[13] |= ADC_TM5_GEN2_LOW_THR_INT_EN;
|
|
|
|
ret = adc_tm5_write(chip, ADC_TM_GEN2_SID, buf, sizeof(buf));
|
|
if (ret) {
|
|
dev_err(chip->dev, "channel %d params write failed: %d\n", channel->channel, ret);
|
|
goto config_fail;
|
|
}
|
|
|
|
ret = adc_tm5_gen2_conv_req(channel->chip);
|
|
if (ret < 0)
|
|
dev_err(chip->dev, "adc-tm channel configure failed with %d\n", ret);
|
|
|
|
config_fail:
|
|
mutex_unlock(&chip->adc_mutex_lock);
|
|
return ret;
|
|
}
|
|
|
|
static int adc_tm5_set_trips(void *data, int low, int high)
|
|
{
|
|
struct adc_tm5_channel *channel = data;
|
|
struct adc_tm5_chip *chip;
|
|
int ret;
|
|
|
|
if (!channel)
|
|
return -EINVAL;
|
|
|
|
chip = channel->chip;
|
|
dev_dbg(chip->dev, "%d:low(mdegC):%d, high(mdegC):%d\n",
|
|
channel->channel, low, high);
|
|
|
|
if (high == INT_MAX && low <= -INT_MAX)
|
|
ret = chip->data->disable_channel(channel);
|
|
else
|
|
ret = chip->data->configure(channel, low, high);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static struct thermal_zone_of_device_ops adc_tm5_thermal_ops = {
|
|
.get_temp = adc_tm5_get_temp,
|
|
.set_trips = adc_tm5_set_trips,
|
|
};
|
|
|
|
static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm)
|
|
{
|
|
unsigned int i;
|
|
struct thermal_zone_device *tzd;
|
|
|
|
for (i = 0; i < adc_tm->nchannels; i++) {
|
|
adc_tm->channels[i].chip = adc_tm;
|
|
|
|
tzd = devm_thermal_zone_of_sensor_register(adc_tm->dev,
|
|
adc_tm->channels[i].channel,
|
|
&adc_tm->channels[i],
|
|
&adc_tm5_thermal_ops);
|
|
if (IS_ERR(tzd)) {
|
|
if (PTR_ERR(tzd) == -ENODEV) {
|
|
dev_warn(adc_tm->dev, "thermal sensor on channel %d is not used\n",
|
|
adc_tm->channels[i].channel);
|
|
continue;
|
|
}
|
|
|
|
dev_err(adc_tm->dev, "Error registering TZ zone for channel %d: %ld\n",
|
|
adc_tm->channels[i].channel, PTR_ERR(tzd));
|
|
return PTR_ERR(tzd);
|
|
}
|
|
adc_tm->channels[i].tzd = tzd;
|
|
if (devm_thermal_add_hwmon_sysfs(tzd))
|
|
dev_warn(adc_tm->dev,
|
|
"Failed to add hwmon sysfs attributes\n");
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int adc_tm_hc_init(struct adc_tm5_chip *chip)
|
|
{
|
|
unsigned int i;
|
|
u8 buf[2];
|
|
int ret;
|
|
|
|
for (i = 0; i < chip->nchannels; i++) {
|
|
if (chip->channels[i].channel >= ADC_TM5_NUM_CHANNELS) {
|
|
dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
buf[0] = chip->decimation;
|
|
buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN;
|
|
|
|
ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf));
|
|
if (ret)
|
|
dev_err(chip->dev, "block write failed: %d\n", ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int adc_tm5_init(struct adc_tm5_chip *chip)
|
|
{
|
|
u8 buf[4], channels_available;
|
|
int ret;
|
|
unsigned int i;
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM,
|
|
&channels_available, sizeof(channels_available));
|
|
if (ret) {
|
|
dev_err(chip->dev, "read failed for BTM channels\n");
|
|
return ret;
|
|
}
|
|
|
|
for (i = 0; i < chip->nchannels; i++) {
|
|
if (chip->channels[i].channel >= channels_available) {
|
|
dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
buf[0] = chip->decimation;
|
|
buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN;
|
|
buf[2] = ADC_TM5_TIMER1;
|
|
buf[3] = FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL2_MASK, ADC_TM5_TIMER2) |
|
|
FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL3_MASK, ADC_TM5_TIMER3);
|
|
|
|
ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf));
|
|
if (ret) {
|
|
dev_err(chip->dev, "block write failed: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int adc_tm5_gen2_init(struct adc_tm5_chip *chip)
|
|
{
|
|
u8 channels_available;
|
|
int ret;
|
|
unsigned int i;
|
|
|
|
ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM,
|
|
&channels_available, sizeof(channels_available));
|
|
if (ret) {
|
|
dev_err(chip->dev, "read failed for BTM channels\n");
|
|
return ret;
|
|
}
|
|
|
|
for (i = 0; i < chip->nchannels; i++) {
|
|
if (chip->channels[i].channel >= channels_available) {
|
|
dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
mutex_init(&chip->adc_mutex_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int adc_tm5_get_dt_channel_data(struct adc_tm5_chip *adc_tm,
|
|
struct adc_tm5_channel *channel,
|
|
struct device_node *node)
|
|
{
|
|
const char *name = node->name;
|
|
u32 chan, value, adc_channel, varr[2];
|
|
int ret;
|
|
struct device *dev = adc_tm->dev;
|
|
struct of_phandle_args args;
|
|
|
|
ret = of_property_read_u32(node, "reg", &chan);
|
|
if (ret) {
|
|
dev_err(dev, "%s: invalid channel number %d\n", name, ret);
|
|
return ret;
|
|
}
|
|
|
|
if (chan >= ADC_TM5_NUM_CHANNELS) {
|
|
dev_err(dev, "%s: channel number too big: %d\n", name, chan);
|
|
return -EINVAL;
|
|
}
|
|
|
|
channel->channel = chan;
|
|
|
|
/*
|
|
* We are tied to PMIC's ADC controller, which always use single
|
|
* argument for channel number. So don't bother parsing
|
|
* #io-channel-cells, just enforce cell_count = 1.
|
|
*/
|
|
ret = of_parse_phandle_with_fixed_args(node, "io-channels", 1, 0, &args);
|
|
if (ret < 0) {
|
|
dev_err(dev, "%s: error parsing ADC channel number %d: %d\n", name, chan, ret);
|
|
return ret;
|
|
}
|
|
of_node_put(args.np);
|
|
|
|
if (args.args_count != 1) {
|
|
dev_err(dev, "%s: invalid args count for ADC channel %d\n", name, chan);
|
|
return -EINVAL;
|
|
}
|
|
|
|
adc_channel = args.args[0];
|
|
if (adc_tm->data->gen == ADC_TM5_GEN2)
|
|
adc_channel &= 0xff;
|
|
|
|
if (adc_channel >= ADC5_MAX_CHANNEL) {
|
|
dev_err(dev, "%s: invalid ADC channel number %d\n", name, chan);
|
|
return -EINVAL;
|
|
}
|
|
channel->adc_channel = args.args[0];
|
|
|
|
channel->iio = devm_of_iio_channel_get_by_name(adc_tm->dev, node, NULL);
|
|
if (IS_ERR(channel->iio)) {
|
|
ret = PTR_ERR(channel->iio);
|
|
if (ret != -EPROBE_DEFER)
|
|
dev_err(dev, "%s: error getting channel: %d\n", name, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
|
|
if (!ret) {
|
|
ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
|
|
if (ret < 0) {
|
|
dev_err(dev, "%s: invalid pre-scaling <%d %d>\n",
|
|
name, varr[0], varr[1]);
|
|
return ret;
|
|
}
|
|
channel->prescale = ret;
|
|
} else {
|
|
/* 1:1 prescale is index 0 */
|
|
channel->prescale = 0;
|
|
}
|
|
|
|
ret = of_property_read_u32(node, "qcom,hw-settle-time-us", &value);
|
|
if (!ret) {
|
|
ret = qcom_adc5_hw_settle_time_from_dt(value, adc_tm->data->hw_settle);
|
|
if (ret < 0) {
|
|
dev_err(dev, "%s invalid hw-settle-time-us %d us\n",
|
|
name, value);
|
|
return ret;
|
|
}
|
|
channel->hw_settle_time = ret;
|
|
} else {
|
|
channel->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
|
|
}
|
|
|
|
if (of_property_read_bool(node, "qcom,ratiometric"))
|
|
channel->cal_method = ADC_TM5_RATIOMETRIC_CAL;
|
|
else
|
|
channel->cal_method = ADC_TM5_ABSOLUTE_CAL;
|
|
|
|
if (adc_tm->data->gen == ADC_TM5_GEN2) {
|
|
ret = of_property_read_u32(node, "qcom,decimation", &value);
|
|
if (!ret) {
|
|
ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation);
|
|
if (ret < 0) {
|
|
dev_err(dev, "invalid decimation %d\n", value);
|
|
return ret;
|
|
}
|
|
channel->decimation = ret;
|
|
} else {
|
|
channel->decimation = ADC5_DECIMATION_DEFAULT;
|
|
}
|
|
|
|
ret = of_property_read_u32(node, "qcom,avg-samples", &value);
|
|
if (!ret) {
|
|
ret = qcom_adc5_avg_samples_from_dt(value);
|
|
if (ret < 0) {
|
|
dev_err(dev, "invalid avg-samples %d\n", value);
|
|
return ret;
|
|
}
|
|
channel->avg_samples = ret;
|
|
} else {
|
|
channel->avg_samples = VADC_DEF_AVG_SAMPLES;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct adc_tm5_data adc_tm5_data_pmic = {
|
|
.full_scale_code_volt = 0x70e4,
|
|
.decimation = (unsigned int []) { 250, 420, 840 },
|
|
.hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700,
|
|
1000, 2000, 4000, 8000, 16000, 32000,
|
|
64000, 128000 },
|
|
.disable_channel = adc_tm5_disable_channel,
|
|
.configure = adc_tm5_configure,
|
|
.isr = adc_tm5_isr,
|
|
.init = adc_tm5_init,
|
|
.irq_name = "pm-adc-tm5",
|
|
.gen = ADC_TM5,
|
|
};
|
|
|
|
static const struct adc_tm5_data adc_tm_hc_data_pmic = {
|
|
.full_scale_code_volt = 0x70e4,
|
|
.decimation = (unsigned int []) { 256, 512, 1024 },
|
|
.hw_settle = (unsigned int []) { 0, 100, 200, 300, 400, 500, 600, 700,
|
|
1000, 2000, 4000, 6000, 8000, 10000 },
|
|
.disable_channel = adc_tm5_disable_channel,
|
|
.configure = adc_tm5_configure,
|
|
.isr = adc_tm5_isr,
|
|
.init = adc_tm_hc_init,
|
|
.irq_name = "pm-adc-tm5",
|
|
.gen = ADC_TM_HC,
|
|
};
|
|
|
|
static const struct adc_tm5_data adc_tm5_gen2_data_pmic = {
|
|
.full_scale_code_volt = 0x70e4,
|
|
.decimation = (unsigned int []) { 85, 340, 1360 },
|
|
.hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700,
|
|
1000, 2000, 4000, 8000, 16000, 32000,
|
|
64000, 128000 },
|
|
.disable_channel = adc_tm5_gen2_disable_channel,
|
|
.configure = adc_tm5_gen2_configure,
|
|
.isr = adc_tm5_gen2_isr,
|
|
.init = adc_tm5_gen2_init,
|
|
.irq_name = "pm-adc-tm5-gen2",
|
|
.gen = ADC_TM5_GEN2,
|
|
};
|
|
|
|
static int adc_tm5_get_dt_data(struct adc_tm5_chip *adc_tm, struct device_node *node)
|
|
{
|
|
struct adc_tm5_channel *channels;
|
|
struct device_node *child;
|
|
u32 value;
|
|
int ret;
|
|
struct device *dev = adc_tm->dev;
|
|
|
|
adc_tm->nchannels = of_get_available_child_count(node);
|
|
if (!adc_tm->nchannels)
|
|
return -EINVAL;
|
|
|
|
adc_tm->channels = devm_kcalloc(dev, adc_tm->nchannels,
|
|
sizeof(*adc_tm->channels), GFP_KERNEL);
|
|
if (!adc_tm->channels)
|
|
return -ENOMEM;
|
|
|
|
channels = adc_tm->channels;
|
|
|
|
adc_tm->data = of_device_get_match_data(dev);
|
|
if (!adc_tm->data)
|
|
adc_tm->data = &adc_tm5_data_pmic;
|
|
|
|
ret = of_property_read_u32(node, "qcom,decimation", &value);
|
|
if (!ret) {
|
|
ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation);
|
|
if (ret < 0) {
|
|
dev_err(dev, "invalid decimation %d\n", value);
|
|
return ret;
|
|
}
|
|
adc_tm->decimation = ret;
|
|
} else {
|
|
adc_tm->decimation = ADC5_DECIMATION_DEFAULT;
|
|
}
|
|
|
|
ret = of_property_read_u32(node, "qcom,avg-samples", &value);
|
|
if (!ret) {
|
|
ret = qcom_adc5_avg_samples_from_dt(value);
|
|
if (ret < 0) {
|
|
dev_err(dev, "invalid avg-samples %d\n", value);
|
|
return ret;
|
|
}
|
|
adc_tm->avg_samples = ret;
|
|
} else {
|
|
adc_tm->avg_samples = VADC_DEF_AVG_SAMPLES;
|
|
}
|
|
|
|
for_each_available_child_of_node(node, child) {
|
|
ret = adc_tm5_get_dt_channel_data(adc_tm, channels, child);
|
|
if (ret) {
|
|
of_node_put(child);
|
|
return ret;
|
|
}
|
|
|
|
channels++;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int adc_tm5_probe(struct platform_device *pdev)
|
|
{
|
|
struct device_node *node = pdev->dev.of_node;
|
|
struct device *dev = &pdev->dev;
|
|
struct adc_tm5_chip *adc_tm;
|
|
struct regmap *regmap;
|
|
int ret, irq;
|
|
u32 reg;
|
|
|
|
regmap = dev_get_regmap(dev->parent, NULL);
|
|
if (!regmap)
|
|
return -ENODEV;
|
|
|
|
ret = of_property_read_u32(node, "reg", ®);
|
|
if (ret)
|
|
return ret;
|
|
|
|
adc_tm = devm_kzalloc(&pdev->dev, sizeof(*adc_tm), GFP_KERNEL);
|
|
if (!adc_tm)
|
|
return -ENOMEM;
|
|
|
|
adc_tm->regmap = regmap;
|
|
adc_tm->dev = dev;
|
|
adc_tm->base = reg;
|
|
|
|
irq = platform_get_irq(pdev, 0);
|
|
if (irq < 0) {
|
|
dev_err(dev, "get_irq failed: %d\n", irq);
|
|
return irq;
|
|
}
|
|
|
|
ret = adc_tm5_get_dt_data(adc_tm, node);
|
|
if (ret) {
|
|
dev_err(dev, "get dt data failed: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = adc_tm->data->init(adc_tm);
|
|
if (ret) {
|
|
dev_err(dev, "adc-tm init failed\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = adc_tm5_register_tzd(adc_tm);
|
|
if (ret) {
|
|
dev_err(dev, "tzd register failed\n");
|
|
return ret;
|
|
}
|
|
|
|
return devm_request_threaded_irq(dev, irq, NULL, adc_tm->data->isr,
|
|
IRQF_ONESHOT, adc_tm->data->irq_name, adc_tm);
|
|
}
|
|
|
|
static const struct of_device_id adc_tm5_match_table[] = {
|
|
{
|
|
.compatible = "qcom,spmi-adc-tm5",
|
|
.data = &adc_tm5_data_pmic,
|
|
},
|
|
{
|
|
.compatible = "qcom,spmi-adc-tm-hc",
|
|
.data = &adc_tm_hc_data_pmic,
|
|
},
|
|
{
|
|
.compatible = "qcom,spmi-adc-tm5-gen2",
|
|
.data = &adc_tm5_gen2_data_pmic,
|
|
},
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, adc_tm5_match_table);
|
|
|
|
static struct platform_driver adc_tm5_driver = {
|
|
.driver = {
|
|
.name = "qcom-spmi-adc-tm5",
|
|
.of_match_table = adc_tm5_match_table,
|
|
},
|
|
.probe = adc_tm5_probe,
|
|
};
|
|
module_platform_driver(adc_tm5_driver);
|
|
|
|
MODULE_DESCRIPTION("SPMI PMIC Thermal Monitor ADC driver");
|
|
MODULE_LICENSE("GPL v2");
|