57 строки
1.6 KiB
C
57 строки
1.6 KiB
C
/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
|
|
/* Copyright 2019 NXP */
|
|
|
|
#ifndef _FSL_ENETC_MDIO_H_
|
|
#define _FSL_ENETC_MDIO_H_
|
|
|
|
#include <linux/phy.h>
|
|
|
|
/* PCS registers */
|
|
#define ENETC_PCS_LINK_TIMER1 0x12
|
|
#define ENETC_PCS_LINK_TIMER1_VAL 0x06a0
|
|
#define ENETC_PCS_LINK_TIMER2 0x13
|
|
#define ENETC_PCS_LINK_TIMER2_VAL 0x0003
|
|
#define ENETC_PCS_IF_MODE 0x14
|
|
#define ENETC_PCS_IF_MODE_SGMII_EN BIT(0)
|
|
#define ENETC_PCS_IF_MODE_USE_SGMII_AN BIT(1)
|
|
#define ENETC_PCS_IF_MODE_SGMII_SPEED(x) (((x) << 2) & GENMASK(3, 2))
|
|
#define ENETC_PCS_IF_MODE_DUPLEX_HALF BIT(3)
|
|
|
|
/* Not a mistake, the SerDes PLL needs to be set at 3.125 GHz by Reset
|
|
* Configuration Word (RCW, outside Linux control) for 2.5G SGMII mode. The PCS
|
|
* still thinks it's at gigabit.
|
|
*/
|
|
enum enetc_pcs_speed {
|
|
ENETC_PCS_SPEED_10 = 0,
|
|
ENETC_PCS_SPEED_100 = 1,
|
|
ENETC_PCS_SPEED_1000 = 2,
|
|
ENETC_PCS_SPEED_2500 = 2,
|
|
};
|
|
|
|
struct enetc_hw;
|
|
|
|
struct enetc_mdio_priv {
|
|
struct enetc_hw *hw;
|
|
int mdio_base;
|
|
};
|
|
|
|
#if IS_REACHABLE(CONFIG_FSL_ENETC_MDIO)
|
|
|
|
int enetc_mdio_read(struct mii_bus *bus, int phy_id, int regnum);
|
|
int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 value);
|
|
struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs);
|
|
|
|
#else
|
|
|
|
static inline int enetc_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
|
|
{ return -EINVAL; }
|
|
static inline int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum,
|
|
u16 value)
|
|
{ return -EINVAL; }
|
|
struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
|
|
{ return ERR_PTR(-EINVAL); }
|
|
|
|
#endif
|
|
|
|
#endif
|