390 строки
10 KiB
C
390 строки
10 KiB
C
/*
|
|
* PCIe host controller driver for ST Microelectronics SPEAr13xx SoCs
|
|
*
|
|
* SPEAr13xx PCIe Glue Layer Source Code
|
|
*
|
|
* Copyright (C) 2010-2014 ST Microelectronics
|
|
* Pratyush Anand <pratyush.anand@gmail.com>
|
|
* Mohit Kumar <mohit.kumar.dhaka@gmail.com>
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without any
|
|
* warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/phy/phy.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/resource.h>
|
|
|
|
#include "pcie-designware.h"
|
|
|
|
struct spear13xx_pcie {
|
|
void __iomem *app_base;
|
|
struct phy *phy;
|
|
struct clk *clk;
|
|
struct pcie_port pp;
|
|
bool is_gen1;
|
|
};
|
|
|
|
struct pcie_app_reg {
|
|
u32 app_ctrl_0; /* cr0 */
|
|
u32 app_ctrl_1; /* cr1 */
|
|
u32 app_status_0; /* cr2 */
|
|
u32 app_status_1; /* cr3 */
|
|
u32 msg_status; /* cr4 */
|
|
u32 msg_payload; /* cr5 */
|
|
u32 int_sts; /* cr6 */
|
|
u32 int_clr; /* cr7 */
|
|
u32 int_mask; /* cr8 */
|
|
u32 mst_bmisc; /* cr9 */
|
|
u32 phy_ctrl; /* cr10 */
|
|
u32 phy_status; /* cr11 */
|
|
u32 cxpl_debug_info_0; /* cr12 */
|
|
u32 cxpl_debug_info_1; /* cr13 */
|
|
u32 ven_msg_ctrl_0; /* cr14 */
|
|
u32 ven_msg_ctrl_1; /* cr15 */
|
|
u32 ven_msg_data_0; /* cr16 */
|
|
u32 ven_msg_data_1; /* cr17 */
|
|
u32 ven_msi_0; /* cr18 */
|
|
u32 ven_msi_1; /* cr19 */
|
|
u32 mst_rmisc; /* cr20 */
|
|
};
|
|
|
|
/* CR0 ID */
|
|
#define RX_LANE_FLIP_EN_ID 0
|
|
#define TX_LANE_FLIP_EN_ID 1
|
|
#define SYS_AUX_PWR_DET_ID 2
|
|
#define APP_LTSSM_ENABLE_ID 3
|
|
#define SYS_ATTEN_BUTTON_PRESSED_ID 4
|
|
#define SYS_MRL_SENSOR_STATE_ID 5
|
|
#define SYS_PWR_FAULT_DET_ID 6
|
|
#define SYS_MRL_SENSOR_CHGED_ID 7
|
|
#define SYS_PRE_DET_CHGED_ID 8
|
|
#define SYS_CMD_CPLED_INT_ID 9
|
|
#define APP_INIT_RST_0_ID 11
|
|
#define APP_REQ_ENTR_L1_ID 12
|
|
#define APP_READY_ENTR_L23_ID 13
|
|
#define APP_REQ_EXIT_L1_ID 14
|
|
#define DEVICE_TYPE_EP (0 << 25)
|
|
#define DEVICE_TYPE_LEP (1 << 25)
|
|
#define DEVICE_TYPE_RC (4 << 25)
|
|
#define SYS_INT_ID 29
|
|
#define MISCTRL_EN_ID 30
|
|
#define REG_TRANSLATION_ENABLE 31
|
|
|
|
/* CR1 ID */
|
|
#define APPS_PM_XMT_TURNOFF_ID 2
|
|
#define APPS_PM_XMT_PME_ID 5
|
|
|
|
/* CR3 ID */
|
|
#define XMLH_LTSSM_STATE_DETECT_QUIET 0x00
|
|
#define XMLH_LTSSM_STATE_DETECT_ACT 0x01
|
|
#define XMLH_LTSSM_STATE_POLL_ACTIVE 0x02
|
|
#define XMLH_LTSSM_STATE_POLL_COMPLIANCE 0x03
|
|
#define XMLH_LTSSM_STATE_POLL_CONFIG 0x04
|
|
#define XMLH_LTSSM_STATE_PRE_DETECT_QUIET 0x05
|
|
#define XMLH_LTSSM_STATE_DETECT_WAIT 0x06
|
|
#define XMLH_LTSSM_STATE_CFG_LINKWD_START 0x07
|
|
#define XMLH_LTSSM_STATE_CFG_LINKWD_ACEPT 0x08
|
|
#define XMLH_LTSSM_STATE_CFG_LANENUM_WAIT 0x09
|
|
#define XMLH_LTSSM_STATE_CFG_LANENUM_ACEPT 0x0A
|
|
#define XMLH_LTSSM_STATE_CFG_COMPLETE 0x0B
|
|
#define XMLH_LTSSM_STATE_CFG_IDLE 0x0C
|
|
#define XMLH_LTSSM_STATE_RCVRY_LOCK 0x0D
|
|
#define XMLH_LTSSM_STATE_RCVRY_SPEED 0x0E
|
|
#define XMLH_LTSSM_STATE_RCVRY_RCVRCFG 0x0F
|
|
#define XMLH_LTSSM_STATE_RCVRY_IDLE 0x10
|
|
#define XMLH_LTSSM_STATE_L0 0x11
|
|
#define XMLH_LTSSM_STATE_L0S 0x12
|
|
#define XMLH_LTSSM_STATE_L123_SEND_EIDLE 0x13
|
|
#define XMLH_LTSSM_STATE_L1_IDLE 0x14
|
|
#define XMLH_LTSSM_STATE_L2_IDLE 0x15
|
|
#define XMLH_LTSSM_STATE_L2_WAKE 0x16
|
|
#define XMLH_LTSSM_STATE_DISABLED_ENTRY 0x17
|
|
#define XMLH_LTSSM_STATE_DISABLED_IDLE 0x18
|
|
#define XMLH_LTSSM_STATE_DISABLED 0x19
|
|
#define XMLH_LTSSM_STATE_LPBK_ENTRY 0x1A
|
|
#define XMLH_LTSSM_STATE_LPBK_ACTIVE 0x1B
|
|
#define XMLH_LTSSM_STATE_LPBK_EXIT 0x1C
|
|
#define XMLH_LTSSM_STATE_LPBK_EXIT_TIMEOUT 0x1D
|
|
#define XMLH_LTSSM_STATE_HOT_RESET_ENTRY 0x1E
|
|
#define XMLH_LTSSM_STATE_HOT_RESET 0x1F
|
|
#define XMLH_LTSSM_STATE_MASK 0x3F
|
|
#define XMLH_LINK_UP (1 << 6)
|
|
|
|
/* CR4 ID */
|
|
#define CFG_MSI_EN_ID 18
|
|
|
|
/* CR6 */
|
|
#define INTA_CTRL_INT (1 << 7)
|
|
#define INTB_CTRL_INT (1 << 8)
|
|
#define INTC_CTRL_INT (1 << 9)
|
|
#define INTD_CTRL_INT (1 << 10)
|
|
#define MSI_CTRL_INT (1 << 26)
|
|
|
|
/* CR19 ID */
|
|
#define VEN_MSI_REQ_ID 11
|
|
#define VEN_MSI_FUN_NUM_ID 8
|
|
#define VEN_MSI_TC_ID 5
|
|
#define VEN_MSI_VECTOR_ID 0
|
|
#define VEN_MSI_REQ_EN ((u32)0x1 << VEN_MSI_REQ_ID)
|
|
#define VEN_MSI_FUN_NUM_MASK ((u32)0x7 << VEN_MSI_FUN_NUM_ID)
|
|
#define VEN_MSI_TC_MASK ((u32)0x7 << VEN_MSI_TC_ID)
|
|
#define VEN_MSI_VECTOR_MASK ((u32)0x1F << VEN_MSI_VECTOR_ID)
|
|
|
|
#define EXP_CAP_ID_OFFSET 0x70
|
|
|
|
#define to_spear13xx_pcie(x) container_of(x, struct spear13xx_pcie, pp)
|
|
|
|
static int spear13xx_pcie_establish_link(struct pcie_port *pp)
|
|
{
|
|
u32 val;
|
|
struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
|
|
struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
|
|
u32 exp_cap_off = EXP_CAP_ID_OFFSET;
|
|
unsigned int retries;
|
|
|
|
if (dw_pcie_link_up(pp)) {
|
|
dev_err(pp->dev, "link already up\n");
|
|
return 0;
|
|
}
|
|
|
|
dw_pcie_setup_rc(pp);
|
|
|
|
/*
|
|
* this controller support only 128 bytes read size, however its
|
|
* default value in capability register is 512 bytes. So force
|
|
* it to 128 here.
|
|
*/
|
|
dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_DEVCTL, 4, &val);
|
|
val &= ~PCI_EXP_DEVCTL_READRQ;
|
|
dw_pcie_cfg_write(pp->dbi_base, exp_cap_off + PCI_EXP_DEVCTL, 4, val);
|
|
|
|
dw_pcie_cfg_write(pp->dbi_base, PCI_VENDOR_ID, 2, 0x104A);
|
|
dw_pcie_cfg_write(pp->dbi_base, PCI_DEVICE_ID, 2, 0xCD80);
|
|
|
|
/*
|
|
* if is_gen1 is set then handle it, so that some buggy card
|
|
* also works
|
|
*/
|
|
if (spear13xx_pcie->is_gen1) {
|
|
dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_LNKCAP, 4,
|
|
&val);
|
|
if ((val & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) {
|
|
val &= ~((u32)PCI_EXP_LNKCAP_SLS);
|
|
val |= PCI_EXP_LNKCAP_SLS_2_5GB;
|
|
dw_pcie_cfg_write(pp->dbi_base, exp_cap_off +
|
|
PCI_EXP_LNKCAP, 4, val);
|
|
}
|
|
|
|
dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_LNKCTL2, 4,
|
|
&val);
|
|
if ((val & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) {
|
|
val &= ~((u32)PCI_EXP_LNKCAP_SLS);
|
|
val |= PCI_EXP_LNKCAP_SLS_2_5GB;
|
|
dw_pcie_cfg_write(pp->dbi_base, exp_cap_off +
|
|
PCI_EXP_LNKCTL2, 4, val);
|
|
}
|
|
}
|
|
|
|
/* enable ltssm */
|
|
writel(DEVICE_TYPE_RC | (1 << MISCTRL_EN_ID)
|
|
| (1 << APP_LTSSM_ENABLE_ID)
|
|
| ((u32)1 << REG_TRANSLATION_ENABLE),
|
|
&app_reg->app_ctrl_0);
|
|
|
|
/* check if the link is up or not */
|
|
for (retries = 0; retries < 10; retries++) {
|
|
if (dw_pcie_link_up(pp)) {
|
|
dev_info(pp->dev, "link up\n");
|
|
return 0;
|
|
}
|
|
mdelay(100);
|
|
}
|
|
|
|
dev_err(pp->dev, "link Fail\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
static irqreturn_t spear13xx_pcie_irq_handler(int irq, void *arg)
|
|
{
|
|
struct pcie_port *pp = arg;
|
|
struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
|
|
struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
|
|
unsigned int status;
|
|
|
|
status = readl(&app_reg->int_sts);
|
|
|
|
if (status & MSI_CTRL_INT) {
|
|
BUG_ON(!IS_ENABLED(CONFIG_PCI_MSI));
|
|
dw_handle_msi_irq(pp);
|
|
}
|
|
|
|
writel(status, &app_reg->int_clr);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static void spear13xx_pcie_enable_interrupts(struct pcie_port *pp)
|
|
{
|
|
struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
|
|
struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
|
|
|
|
/* Enable MSI interrupt */
|
|
if (IS_ENABLED(CONFIG_PCI_MSI)) {
|
|
dw_pcie_msi_init(pp);
|
|
writel(readl(&app_reg->int_mask) |
|
|
MSI_CTRL_INT, &app_reg->int_mask);
|
|
}
|
|
}
|
|
|
|
static int spear13xx_pcie_link_up(struct pcie_port *pp)
|
|
{
|
|
struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp);
|
|
struct pcie_app_reg *app_reg = spear13xx_pcie->app_base;
|
|
|
|
if (readl(&app_reg->app_status_1) & XMLH_LINK_UP)
|
|
return 1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void spear13xx_pcie_host_init(struct pcie_port *pp)
|
|
{
|
|
spear13xx_pcie_establish_link(pp);
|
|
spear13xx_pcie_enable_interrupts(pp);
|
|
}
|
|
|
|
static struct pcie_host_ops spear13xx_pcie_host_ops = {
|
|
.link_up = spear13xx_pcie_link_up,
|
|
.host_init = spear13xx_pcie_host_init,
|
|
};
|
|
|
|
static int spear13xx_add_pcie_port(struct pcie_port *pp,
|
|
struct platform_device *pdev)
|
|
{
|
|
struct device *dev = &pdev->dev;
|
|
int ret;
|
|
|
|
pp->irq = platform_get_irq(pdev, 0);
|
|
if (!pp->irq) {
|
|
dev_err(dev, "failed to get irq\n");
|
|
return -ENODEV;
|
|
}
|
|
ret = devm_request_irq(dev, pp->irq, spear13xx_pcie_irq_handler,
|
|
IRQF_SHARED, "spear1340-pcie", pp);
|
|
if (ret) {
|
|
dev_err(dev, "failed to request irq %d\n", pp->irq);
|
|
return ret;
|
|
}
|
|
|
|
pp->root_bus_nr = -1;
|
|
pp->ops = &spear13xx_pcie_host_ops;
|
|
|
|
ret = dw_pcie_host_init(pp);
|
|
if (ret) {
|
|
dev_err(dev, "failed to initialize host\n");
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int spear13xx_pcie_probe(struct platform_device *pdev)
|
|
{
|
|
struct spear13xx_pcie *spear13xx_pcie;
|
|
struct pcie_port *pp;
|
|
struct device *dev = &pdev->dev;
|
|
struct device_node *np = pdev->dev.of_node;
|
|
struct resource *dbi_base;
|
|
int ret;
|
|
|
|
spear13xx_pcie = devm_kzalloc(dev, sizeof(*spear13xx_pcie), GFP_KERNEL);
|
|
if (!spear13xx_pcie)
|
|
return -ENOMEM;
|
|
|
|
spear13xx_pcie->phy = devm_phy_get(dev, "pcie-phy");
|
|
if (IS_ERR(spear13xx_pcie->phy)) {
|
|
ret = PTR_ERR(spear13xx_pcie->phy);
|
|
if (ret == -EPROBE_DEFER)
|
|
dev_info(dev, "probe deferred\n");
|
|
else
|
|
dev_err(dev, "couldn't get pcie-phy\n");
|
|
return ret;
|
|
}
|
|
|
|
phy_init(spear13xx_pcie->phy);
|
|
|
|
spear13xx_pcie->clk = devm_clk_get(dev, NULL);
|
|
if (IS_ERR(spear13xx_pcie->clk)) {
|
|
dev_err(dev, "couldn't get clk for pcie\n");
|
|
return PTR_ERR(spear13xx_pcie->clk);
|
|
}
|
|
ret = clk_prepare_enable(spear13xx_pcie->clk);
|
|
if (ret) {
|
|
dev_err(dev, "couldn't enable clk for pcie\n");
|
|
return ret;
|
|
}
|
|
|
|
pp = &spear13xx_pcie->pp;
|
|
|
|
pp->dev = dev;
|
|
|
|
dbi_base = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
|
|
pp->dbi_base = devm_ioremap_resource(dev, dbi_base);
|
|
if (IS_ERR(pp->dbi_base)) {
|
|
dev_err(dev, "couldn't remap dbi base %p\n", dbi_base);
|
|
ret = PTR_ERR(pp->dbi_base);
|
|
goto fail_clk;
|
|
}
|
|
spear13xx_pcie->app_base = pp->dbi_base + 0x2000;
|
|
|
|
if (of_property_read_bool(np, "st,pcie-is-gen1"))
|
|
spear13xx_pcie->is_gen1 = true;
|
|
|
|
ret = spear13xx_add_pcie_port(pp, pdev);
|
|
if (ret < 0)
|
|
goto fail_clk;
|
|
|
|
platform_set_drvdata(pdev, spear13xx_pcie);
|
|
return 0;
|
|
|
|
fail_clk:
|
|
clk_disable_unprepare(spear13xx_pcie->clk);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static const struct of_device_id spear13xx_pcie_of_match[] = {
|
|
{ .compatible = "st,spear1340-pcie", },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, spear13xx_pcie_of_match);
|
|
|
|
static struct platform_driver spear13xx_pcie_driver = {
|
|
.probe = spear13xx_pcie_probe,
|
|
.driver = {
|
|
.name = "spear-pcie",
|
|
.of_match_table = of_match_ptr(spear13xx_pcie_of_match),
|
|
},
|
|
};
|
|
|
|
/* SPEAr13xx PCIe driver does not allow module unload */
|
|
|
|
static int __init spear13xx_pcie_init(void)
|
|
{
|
|
return platform_driver_register(&spear13xx_pcie_driver);
|
|
}
|
|
module_init(spear13xx_pcie_init);
|
|
|
|
MODULE_DESCRIPTION("ST Microelectronics SPEAr13xx PCIe host controller driver");
|
|
MODULE_AUTHOR("Pratyush Anand <pratyush.anand@gmail.com>");
|
|
MODULE_LICENSE("GPL v2");
|