1724 строки
59 KiB
C
1724 строки
59 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* AppliedMicro X-Gene Multi-purpose PHY driver
|
|
*
|
|
* Copyright (c) 2014, Applied Micro Circuits Corporation
|
|
* Author: Loc Ho <lho@apm.com>
|
|
* Tuan Phan <tphan@apm.com>
|
|
* Suman Tripathi <stripathi@apm.com>
|
|
*
|
|
* The APM X-Gene PHY consists of two PLL clock macro's (CMU) and lanes.
|
|
* The first PLL clock macro is used for internal reference clock. The second
|
|
* PLL clock macro is used to generate the clock for the PHY. This driver
|
|
* configures the first PLL CMU, the second PLL CMU, and programs the PHY to
|
|
* operate according to the mode of operation. The first PLL CMU is only
|
|
* required if internal clock is enabled.
|
|
*
|
|
* Logical Layer Out Of HW module units:
|
|
*
|
|
* -----------------
|
|
* | Internal | |------|
|
|
* | Ref PLL CMU |----| | ------------- ---------
|
|
* ------------ ---- | MUX |-----|PHY PLL CMU|----| Serdes|
|
|
* | | | | ---------
|
|
* External Clock ------| | -------------
|
|
* |------|
|
|
*
|
|
* The Ref PLL CMU CSR (Configuration System Registers) is accessed
|
|
* indirectly from the SDS offset at 0x2000. It is only required for
|
|
* internal reference clock.
|
|
* The PHY PLL CMU CSR is accessed indirectly from the SDS offset at 0x0000.
|
|
* The Serdes CSR is accessed indirectly from the SDS offset at 0x0400.
|
|
*
|
|
* The Ref PLL CMU can be located within the same PHY IP or outside the PHY IP
|
|
* due to shared Ref PLL CMU. For PHY with Ref PLL CMU shared with another IP,
|
|
* it is located outside the PHY IP. This is the case for the PHY located
|
|
* at 0x1f23a000 (SATA Port 4/5). For such PHY, another resource is required
|
|
* to located the SDS/Ref PLL CMU module and its clock for that IP enabled.
|
|
*
|
|
* Currently, this driver only supports Gen3 SATA mode with external clock.
|
|
*/
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/io.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/phy/phy.h>
|
|
#include <linux/clk.h>
|
|
|
|
/* Max 2 lanes per a PHY unit */
|
|
#define MAX_LANE 2
|
|
|
|
/* Register offset inside the PHY */
|
|
#define SERDES_PLL_INDIRECT_OFFSET 0x0000
|
|
#define SERDES_PLL_REF_INDIRECT_OFFSET 0x2000
|
|
#define SERDES_INDIRECT_OFFSET 0x0400
|
|
#define SERDES_LANE_STRIDE 0x0200
|
|
|
|
/* Some default Serdes parameters */
|
|
#define DEFAULT_SATA_TXBOOST_GAIN { 0x1e, 0x1e, 0x1e }
|
|
#define DEFAULT_SATA_TXEYEDIRECTION { 0x0, 0x0, 0x0 }
|
|
#define DEFAULT_SATA_TXEYETUNING { 0xa, 0xa, 0xa }
|
|
#define DEFAULT_SATA_SPD_SEL { 0x1, 0x3, 0x7 }
|
|
#define DEFAULT_SATA_TXAMP { 0x8, 0x8, 0x8 }
|
|
#define DEFAULT_SATA_TXCN1 { 0x2, 0x2, 0x2 }
|
|
#define DEFAULT_SATA_TXCN2 { 0x0, 0x0, 0x0 }
|
|
#define DEFAULT_SATA_TXCP1 { 0xa, 0xa, 0xa }
|
|
|
|
#define SATA_SPD_SEL_GEN3 0x7
|
|
#define SATA_SPD_SEL_GEN2 0x3
|
|
#define SATA_SPD_SEL_GEN1 0x1
|
|
|
|
#define SSC_DISABLE 0
|
|
#define SSC_ENABLE 1
|
|
|
|
#define FBDIV_VAL_50M 0x77
|
|
#define REFDIV_VAL_50M 0x1
|
|
#define FBDIV_VAL_100M 0x3B
|
|
#define REFDIV_VAL_100M 0x0
|
|
|
|
/* SATA Clock/Reset CSR */
|
|
#define SATACLKENREG 0x00000000
|
|
#define SATA0_CORE_CLKEN 0x00000002
|
|
#define SATA1_CORE_CLKEN 0x00000004
|
|
#define SATASRESETREG 0x00000004
|
|
#define SATA_MEM_RESET_MASK 0x00000020
|
|
#define SATA_MEM_RESET_RD(src) (((src) & 0x00000020) >> 5)
|
|
#define SATA_SDS_RESET_MASK 0x00000004
|
|
#define SATA_CSR_RESET_MASK 0x00000001
|
|
#define SATA_CORE_RESET_MASK 0x00000002
|
|
#define SATA_PMCLK_RESET_MASK 0x00000010
|
|
#define SATA_PCLK_RESET_MASK 0x00000008
|
|
|
|
/* SDS CSR used for PHY Indirect access */
|
|
#define SATA_ENET_SDS_PCS_CTL0 0x00000000
|
|
#define REGSPEC_CFG_I_TX_WORDMODE0_SET(dst, src) \
|
|
(((dst) & ~0x00070000) | (((u32) (src) << 16) & 0x00070000))
|
|
#define REGSPEC_CFG_I_RX_WORDMODE0_SET(dst, src) \
|
|
(((dst) & ~0x00e00000) | (((u32) (src) << 21) & 0x00e00000))
|
|
#define SATA_ENET_SDS_CTL0 0x0000000c
|
|
#define REGSPEC_CFG_I_CUSTOMER_PIN_MODE0_SET(dst, src) \
|
|
(((dst) & ~0x00007fff) | (((u32) (src)) & 0x00007fff))
|
|
#define SATA_ENET_SDS_CTL1 0x00000010
|
|
#define CFG_I_SPD_SEL_CDR_OVR1_SET(dst, src) \
|
|
(((dst) & ~0x0000000f) | (((u32) (src)) & 0x0000000f))
|
|
#define SATA_ENET_SDS_RST_CTL 0x00000024
|
|
#define SATA_ENET_SDS_IND_CMD_REG 0x0000003c
|
|
#define CFG_IND_WR_CMD_MASK 0x00000001
|
|
#define CFG_IND_RD_CMD_MASK 0x00000002
|
|
#define CFG_IND_CMD_DONE_MASK 0x00000004
|
|
#define CFG_IND_ADDR_SET(dst, src) \
|
|
(((dst) & ~0x003ffff0) | (((u32) (src) << 4) & 0x003ffff0))
|
|
#define SATA_ENET_SDS_IND_RDATA_REG 0x00000040
|
|
#define SATA_ENET_SDS_IND_WDATA_REG 0x00000044
|
|
#define SATA_ENET_CLK_MACRO_REG 0x0000004c
|
|
#define I_RESET_B_SET(dst, src) \
|
|
(((dst) & ~0x00000001) | (((u32) (src)) & 0x00000001))
|
|
#define I_PLL_FBDIV_SET(dst, src) \
|
|
(((dst) & ~0x001ff000) | (((u32) (src) << 12) & 0x001ff000))
|
|
#define I_CUSTOMEROV_SET(dst, src) \
|
|
(((dst) & ~0x00000f80) | (((u32) (src) << 7) & 0x00000f80))
|
|
#define O_PLL_LOCK_RD(src) (((src) & 0x40000000) >> 30)
|
|
#define O_PLL_READY_RD(src) (((src) & 0x80000000) >> 31)
|
|
|
|
/* PLL Clock Macro Unit (CMU) CSR accessing from SDS indirectly */
|
|
#define CMU_REG0 0x00000
|
|
#define CMU_REG0_PLL_REF_SEL_MASK 0x00002000
|
|
#define CMU_REG0_PLL_REF_SEL_SET(dst, src) \
|
|
(((dst) & ~0x00002000) | (((u32) (src) << 13) & 0x00002000))
|
|
#define CMU_REG0_PDOWN_MASK 0x00004000
|
|
#define CMU_REG0_CAL_COUNT_RESOL_SET(dst, src) \
|
|
(((dst) & ~0x000000e0) | (((u32) (src) << 5) & 0x000000e0))
|
|
#define CMU_REG1 0x00002
|
|
#define CMU_REG1_PLL_CP_SET(dst, src) \
|
|
(((dst) & ~0x00003c00) | (((u32) (src) << 10) & 0x00003c00))
|
|
#define CMU_REG1_PLL_MANUALCAL_SET(dst, src) \
|
|
(((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
|
|
#define CMU_REG1_PLL_CP_SEL_SET(dst, src) \
|
|
(((dst) & ~0x000003e0) | (((u32) (src) << 5) & 0x000003e0))
|
|
#define CMU_REG1_REFCLK_CMOS_SEL_MASK 0x00000001
|
|
#define CMU_REG1_REFCLK_CMOS_SEL_SET(dst, src) \
|
|
(((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
|
|
#define CMU_REG2 0x00004
|
|
#define CMU_REG2_PLL_REFDIV_SET(dst, src) \
|
|
(((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
|
|
#define CMU_REG2_PLL_LFRES_SET(dst, src) \
|
|
(((dst) & ~0x0000001e) | (((u32) (src) << 1) & 0x0000001e))
|
|
#define CMU_REG2_PLL_FBDIV_SET(dst, src) \
|
|
(((dst) & ~0x00003fe0) | (((u32) (src) << 5) & 0x00003fe0))
|
|
#define CMU_REG3 0x00006
|
|
#define CMU_REG3_VCOVARSEL_SET(dst, src) \
|
|
(((dst) & ~0x0000000f) | (((u32) (src) << 0) & 0x0000000f))
|
|
#define CMU_REG3_VCO_MOMSEL_INIT_SET(dst, src) \
|
|
(((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
|
|
#define CMU_REG3_VCO_MANMOMSEL_SET(dst, src) \
|
|
(((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
|
|
#define CMU_REG4 0x00008
|
|
#define CMU_REG5 0x0000a
|
|
#define CMU_REG5_PLL_LFSMCAP_SET(dst, src) \
|
|
(((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
|
|
#define CMU_REG5_PLL_LOCK_RESOLUTION_SET(dst, src) \
|
|
(((dst) & ~0x0000000e) | (((u32) (src) << 1) & 0x0000000e))
|
|
#define CMU_REG5_PLL_LFCAP_SET(dst, src) \
|
|
(((dst) & ~0x00003000) | (((u32) (src) << 12) & 0x00003000))
|
|
#define CMU_REG5_PLL_RESETB_MASK 0x00000001
|
|
#define CMU_REG6 0x0000c
|
|
#define CMU_REG6_PLL_VREGTRIM_SET(dst, src) \
|
|
(((dst) & ~0x00000600) | (((u32) (src) << 9) & 0x00000600))
|
|
#define CMU_REG6_MAN_PVT_CAL_SET(dst, src) \
|
|
(((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
|
|
#define CMU_REG7 0x0000e
|
|
#define CMU_REG7_PLL_CALIB_DONE_RD(src) ((0x00004000 & (u32) (src)) >> 14)
|
|
#define CMU_REG7_VCO_CAL_FAIL_RD(src) ((0x00000c00 & (u32) (src)) >> 10)
|
|
#define CMU_REG8 0x00010
|
|
#define CMU_REG9 0x00012
|
|
#define CMU_REG9_WORD_LEN_8BIT 0x000
|
|
#define CMU_REG9_WORD_LEN_10BIT 0x001
|
|
#define CMU_REG9_WORD_LEN_16BIT 0x002
|
|
#define CMU_REG9_WORD_LEN_20BIT 0x003
|
|
#define CMU_REG9_WORD_LEN_32BIT 0x004
|
|
#define CMU_REG9_WORD_LEN_40BIT 0x005
|
|
#define CMU_REG9_WORD_LEN_64BIT 0x006
|
|
#define CMU_REG9_WORD_LEN_66BIT 0x007
|
|
#define CMU_REG9_TX_WORD_MODE_CH1_SET(dst, src) \
|
|
(((dst) & ~0x00000380) | (((u32) (src) << 7) & 0x00000380))
|
|
#define CMU_REG9_TX_WORD_MODE_CH0_SET(dst, src) \
|
|
(((dst) & ~0x00000070) | (((u32) (src) << 4) & 0x00000070))
|
|
#define CMU_REG9_PLL_POST_DIVBY2_SET(dst, src) \
|
|
(((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
|
|
#define CMU_REG9_VBG_BYPASSB_SET(dst, src) \
|
|
(((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
|
|
#define CMU_REG9_IGEN_BYPASS_SET(dst, src) \
|
|
(((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
|
|
#define CMU_REG10 0x00014
|
|
#define CMU_REG10_VREG_REFSEL_SET(dst, src) \
|
|
(((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
|
|
#define CMU_REG11 0x00016
|
|
#define CMU_REG12 0x00018
|
|
#define CMU_REG12_STATE_DELAY9_SET(dst, src) \
|
|
(((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0))
|
|
#define CMU_REG13 0x0001a
|
|
#define CMU_REG14 0x0001c
|
|
#define CMU_REG15 0x0001e
|
|
#define CMU_REG16 0x00020
|
|
#define CMU_REG16_PVT_DN_MAN_ENA_MASK 0x00000001
|
|
#define CMU_REG16_PVT_UP_MAN_ENA_MASK 0x00000002
|
|
#define CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(dst, src) \
|
|
(((dst) & ~0x0000001c) | (((u32) (src) << 2) & 0x0000001c))
|
|
#define CMU_REG16_CALIBRATION_DONE_OVERRIDE_SET(dst, src) \
|
|
(((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
|
|
#define CMU_REG16_BYPASS_PLL_LOCK_SET(dst, src) \
|
|
(((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020))
|
|
#define CMU_REG17 0x00022
|
|
#define CMU_REG17_PVT_CODE_R2A_SET(dst, src) \
|
|
(((dst) & ~0x00007f00) | (((u32) (src) << 8) & 0x00007f00))
|
|
#define CMU_REG17_RESERVED_7_SET(dst, src) \
|
|
(((dst) & ~0x000000e0) | (((u32) (src) << 5) & 0x000000e0))
|
|
#define CMU_REG17_PVT_TERM_MAN_ENA_MASK 0x00008000
|
|
#define CMU_REG18 0x00024
|
|
#define CMU_REG19 0x00026
|
|
#define CMU_REG20 0x00028
|
|
#define CMU_REG21 0x0002a
|
|
#define CMU_REG22 0x0002c
|
|
#define CMU_REG23 0x0002e
|
|
#define CMU_REG24 0x00030
|
|
#define CMU_REG25 0x00032
|
|
#define CMU_REG26 0x00034
|
|
#define CMU_REG26_FORCE_PLL_LOCK_SET(dst, src) \
|
|
(((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
|
|
#define CMU_REG27 0x00036
|
|
#define CMU_REG28 0x00038
|
|
#define CMU_REG29 0x0003a
|
|
#define CMU_REG30 0x0003c
|
|
#define CMU_REG30_LOCK_COUNT_SET(dst, src) \
|
|
(((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))
|
|
#define CMU_REG30_PCIE_MODE_SET(dst, src) \
|
|
(((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
|
|
#define CMU_REG31 0x0003e
|
|
#define CMU_REG32 0x00040
|
|
#define CMU_REG32_FORCE_VCOCAL_START_MASK 0x00004000
|
|
#define CMU_REG32_PVT_CAL_WAIT_SEL_SET(dst, src) \
|
|
(((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))
|
|
#define CMU_REG32_IREF_ADJ_SET(dst, src) \
|
|
(((dst) & ~0x00000180) | (((u32) (src) << 7) & 0x00000180))
|
|
#define CMU_REG33 0x00042
|
|
#define CMU_REG34 0x00044
|
|
#define CMU_REG34_VCO_CAL_VTH_LO_MAX_SET(dst, src) \
|
|
(((dst) & ~0x0000000f) | (((u32) (src) << 0) & 0x0000000f))
|
|
#define CMU_REG34_VCO_CAL_VTH_HI_MAX_SET(dst, src) \
|
|
(((dst) & ~0x00000f00) | (((u32) (src) << 8) & 0x00000f00))
|
|
#define CMU_REG34_VCO_CAL_VTH_LO_MIN_SET(dst, src) \
|
|
(((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0))
|
|
#define CMU_REG34_VCO_CAL_VTH_HI_MIN_SET(dst, src) \
|
|
(((dst) & ~0x0000f000) | (((u32) (src) << 12) & 0x0000f000))
|
|
#define CMU_REG35 0x00046
|
|
#define CMU_REG35_PLL_SSC_MOD_SET(dst, src) \
|
|
(((dst) & ~0x0000fe00) | (((u32) (src) << 9) & 0x0000fe00))
|
|
#define CMU_REG36 0x00048
|
|
#define CMU_REG36_PLL_SSC_EN_SET(dst, src) \
|
|
(((dst) & ~0x00000010) | (((u32) (src) << 4) & 0x00000010))
|
|
#define CMU_REG36_PLL_SSC_VSTEP_SET(dst, src) \
|
|
(((dst) & ~0x0000ffc0) | (((u32) (src) << 6) & 0x0000ffc0))
|
|
#define CMU_REG36_PLL_SSC_DSMSEL_SET(dst, src) \
|
|
(((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020))
|
|
#define CMU_REG37 0x0004a
|
|
#define CMU_REG38 0x0004c
|
|
#define CMU_REG39 0x0004e
|
|
|
|
/* PHY lane CSR accessing from SDS indirectly */
|
|
#define RXTX_REG0 0x000
|
|
#define RXTX_REG0_CTLE_EQ_HR_SET(dst, src) \
|
|
(((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
|
|
#define RXTX_REG0_CTLE_EQ_QR_SET(dst, src) \
|
|
(((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
|
|
#define RXTX_REG0_CTLE_EQ_FR_SET(dst, src) \
|
|
(((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
|
|
#define RXTX_REG1 0x002
|
|
#define RXTX_REG1_RXACVCM_SET(dst, src) \
|
|
(((dst) & ~0x0000f000) | (((u32) (src) << 12) & 0x0000f000))
|
|
#define RXTX_REG1_CTLE_EQ_SET(dst, src) \
|
|
(((dst) & ~0x00000f80) | (((u32) (src) << 7) & 0x00000f80))
|
|
#define RXTX_REG1_RXVREG1_SET(dst, src) \
|
|
(((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060))
|
|
#define RXTX_REG1_RXIREF_ADJ_SET(dst, src) \
|
|
(((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))
|
|
#define RXTX_REG2 0x004
|
|
#define RXTX_REG2_VTT_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
|
|
#define RXTX_REG2_TX_FIFO_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020))
|
|
#define RXTX_REG2_VTT_SEL_SET(dst, src) \
|
|
(((dst) & ~0x000000c0) | (((u32) (src) << 6) & 0x000000c0))
|
|
#define RXTX_REG4 0x008
|
|
#define RXTX_REG4_TX_LOOPBACK_BUF_EN_MASK 0x00000040
|
|
#define RXTX_REG4_TX_DATA_RATE_SET(dst, src) \
|
|
(((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
|
|
#define RXTX_REG4_TX_WORD_MODE_SET(dst, src) \
|
|
(((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
|
|
#define RXTX_REG5 0x00a
|
|
#define RXTX_REG5_TX_CN1_SET(dst, src) \
|
|
(((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
|
|
#define RXTX_REG5_TX_CP1_SET(dst, src) \
|
|
(((dst) & ~0x000007e0) | (((u32) (src) << 5) & 0x000007e0))
|
|
#define RXTX_REG5_TX_CN2_SET(dst, src) \
|
|
(((dst) & ~0x0000001f) | (((u32) (src) << 0) & 0x0000001f))
|
|
#define RXTX_REG6 0x00c
|
|
#define RXTX_REG6_TXAMP_CNTL_SET(dst, src) \
|
|
(((dst) & ~0x00000780) | (((u32) (src) << 7) & 0x00000780))
|
|
#define RXTX_REG6_TXAMP_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
|
|
#define RXTX_REG6_RX_BIST_ERRCNT_RD_SET(dst, src) \
|
|
(((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
|
|
#define RXTX_REG6_TX_IDLE_SET(dst, src) \
|
|
(((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
|
|
#define RXTX_REG6_RX_BIST_RESYNC_SET(dst, src) \
|
|
(((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
|
|
#define RXTX_REG7 0x00e
|
|
#define RXTX_REG7_RESETB_RXD_MASK 0x00000100
|
|
#define RXTX_REG7_RESETB_RXA_MASK 0x00000080
|
|
#define RXTX_REG7_BIST_ENA_RX_SET(dst, src) \
|
|
(((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
|
|
#define RXTX_REG7_RX_WORD_MODE_SET(dst, src) \
|
|
(((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
|
|
#define RXTX_REG8 0x010
|
|
#define RXTX_REG8_CDR_LOOP_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00004000) | (((u32) (src) << 14) & 0x00004000))
|
|
#define RXTX_REG8_CDR_BYPASS_RXLOS_SET(dst, src) \
|
|
(((dst) & ~0x00000800) | (((u32) (src) << 11) & 0x00000800))
|
|
#define RXTX_REG8_SSC_ENABLE_SET(dst, src) \
|
|
(((dst) & ~0x00000200) | (((u32) (src) << 9) & 0x00000200))
|
|
#define RXTX_REG8_SD_VREF_SET(dst, src) \
|
|
(((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0))
|
|
#define RXTX_REG8_SD_DISABLE_SET(dst, src) \
|
|
(((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
|
|
#define RXTX_REG7 0x00e
|
|
#define RXTX_REG7_RESETB_RXD_SET(dst, src) \
|
|
(((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
|
|
#define RXTX_REG7_RESETB_RXA_SET(dst, src) \
|
|
(((dst) & ~0x00000080) | (((u32) (src) << 7) & 0x00000080))
|
|
#define RXTX_REG7_LOOP_BACK_ENA_CTLE_MASK 0x00004000
|
|
#define RXTX_REG7_LOOP_BACK_ENA_CTLE_SET(dst, src) \
|
|
(((dst) & ~0x00004000) | (((u32) (src) << 14) & 0x00004000))
|
|
#define RXTX_REG11 0x016
|
|
#define RXTX_REG11_PHASE_ADJUST_LIMIT_SET(dst, src) \
|
|
(((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
|
|
#define RXTX_REG12 0x018
|
|
#define RXTX_REG12_LATCH_OFF_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00002000) | (((u32) (src) << 13) & 0x00002000))
|
|
#define RXTX_REG12_SUMOS_ENABLE_SET(dst, src) \
|
|
(((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
|
|
#define RXTX_REG12_RX_DET_TERM_ENABLE_MASK 0x00000002
|
|
#define RXTX_REG12_RX_DET_TERM_ENABLE_SET(dst, src) \
|
|
(((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
|
|
#define RXTX_REG13 0x01a
|
|
#define RXTX_REG14 0x01c
|
|
#define RXTX_REG14_CLTE_LATCAL_MAN_PROG_SET(dst, src) \
|
|
(((dst) & ~0x0000003f) | (((u32) (src) << 0) & 0x0000003f))
|
|
#define RXTX_REG14_CTLE_LATCAL_MAN_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040))
|
|
#define RXTX_REG26 0x034
|
|
#define RXTX_REG26_PERIOD_ERROR_LATCH_SET(dst, src) \
|
|
(((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
|
|
#define RXTX_REG26_BLWC_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
|
|
#define RXTX_REG21 0x02a
|
|
#define RXTX_REG21_DO_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
|
|
#define RXTX_REG21_XO_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
|
|
#define RXTX_REG21_LATCH_CAL_FAIL_ODD_RD(src) ((0x0000000f & (u32)(src)))
|
|
#define RXTX_REG22 0x02c
|
|
#define RXTX_REG22_SO_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
|
|
#define RXTX_REG22_EO_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
|
|
#define RXTX_REG22_LATCH_CAL_FAIL_EVEN_RD(src) ((0x0000000f & (u32)(src)))
|
|
#define RXTX_REG23 0x02e
|
|
#define RXTX_REG23_DE_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
|
|
#define RXTX_REG23_XE_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
|
|
#define RXTX_REG24 0x030
|
|
#define RXTX_REG24_EE_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10)
|
|
#define RXTX_REG24_SE_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4)
|
|
#define RXTX_REG27 0x036
|
|
#define RXTX_REG28 0x038
|
|
#define RXTX_REG31 0x03e
|
|
#define RXTX_REG38 0x04c
|
|
#define RXTX_REG38_CUSTOMER_PINMODE_INV_SET(dst, src) \
|
|
(((dst) & 0x0000fffe) | (((u32) (src) << 1) & 0x0000fffe))
|
|
#define RXTX_REG39 0x04e
|
|
#define RXTX_REG40 0x050
|
|
#define RXTX_REG41 0x052
|
|
#define RXTX_REG42 0x054
|
|
#define RXTX_REG43 0x056
|
|
#define RXTX_REG44 0x058
|
|
#define RXTX_REG45 0x05a
|
|
#define RXTX_REG46 0x05c
|
|
#define RXTX_REG47 0x05e
|
|
#define RXTX_REG48 0x060
|
|
#define RXTX_REG49 0x062
|
|
#define RXTX_REG50 0x064
|
|
#define RXTX_REG51 0x066
|
|
#define RXTX_REG52 0x068
|
|
#define RXTX_REG53 0x06a
|
|
#define RXTX_REG54 0x06c
|
|
#define RXTX_REG55 0x06e
|
|
#define RXTX_REG61 0x07a
|
|
#define RXTX_REG61_ISCAN_INBERT_SET(dst, src) \
|
|
(((dst) & ~0x00000010) | (((u32) (src) << 4) & 0x00000010))
|
|
#define RXTX_REG61_LOADFREQ_SHIFT_SET(dst, src) \
|
|
(((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
|
|
#define RXTX_REG61_EYE_COUNT_WIDTH_SEL_SET(dst, src) \
|
|
(((dst) & ~0x000000c0) | (((u32) (src) << 6) & 0x000000c0))
|
|
#define RXTX_REG61_SPD_SEL_CDR_SET(dst, src) \
|
|
(((dst) & ~0x00003c00) | (((u32) (src) << 10) & 0x00003c00))
|
|
#define RXTX_REG62 0x07c
|
|
#define RXTX_REG62_PERIOD_H1_QLATCH_SET(dst, src) \
|
|
(((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800))
|
|
#define RXTX_REG81 0x0a2
|
|
#define RXTX_REG89_MU_TH7_SET(dst, src) \
|
|
(((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
|
|
#define RXTX_REG89_MU_TH8_SET(dst, src) \
|
|
(((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
|
|
#define RXTX_REG89_MU_TH9_SET(dst, src) \
|
|
(((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
|
|
#define RXTX_REG96 0x0c0
|
|
#define RXTX_REG96_MU_FREQ1_SET(dst, src) \
|
|
(((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
|
|
#define RXTX_REG96_MU_FREQ2_SET(dst, src) \
|
|
(((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
|
|
#define RXTX_REG96_MU_FREQ3_SET(dst, src) \
|
|
(((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
|
|
#define RXTX_REG99 0x0c6
|
|
#define RXTX_REG99_MU_PHASE1_SET(dst, src) \
|
|
(((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800))
|
|
#define RXTX_REG99_MU_PHASE2_SET(dst, src) \
|
|
(((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0))
|
|
#define RXTX_REG99_MU_PHASE3_SET(dst, src) \
|
|
(((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e))
|
|
#define RXTX_REG102 0x0cc
|
|
#define RXTX_REG102_FREQLOOP_LIMIT_SET(dst, src) \
|
|
(((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060))
|
|
#define RXTX_REG114 0x0e4
|
|
#define RXTX_REG121 0x0f2
|
|
#define RXTX_REG121_SUMOS_CAL_CODE_RD(src) ((0x0000003e & (u32)(src)) >> 0x1)
|
|
#define RXTX_REG125 0x0fa
|
|
#define RXTX_REG125_PQ_REG_SET(dst, src) \
|
|
(((dst) & ~0x0000fe00) | (((u32) (src) << 9) & 0x0000fe00))
|
|
#define RXTX_REG125_SIGN_PQ_SET(dst, src) \
|
|
(((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100))
|
|
#define RXTX_REG125_SIGN_PQ_2C_SET(dst, src) \
|
|
(((dst) & ~0x00000080) | (((u32) (src) << 7) & 0x00000080))
|
|
#define RXTX_REG125_PHZ_MANUALCODE_SET(dst, src) \
|
|
(((dst) & ~0x0000007c) | (((u32) (src) << 2) & 0x0000007c))
|
|
#define RXTX_REG125_PHZ_MANUAL_SET(dst, src) \
|
|
(((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
|
|
#define RXTX_REG127 0x0fe
|
|
#define RXTX_REG127_FORCE_SUM_CAL_START_MASK 0x00000002
|
|
#define RXTX_REG127_FORCE_LAT_CAL_START_MASK 0x00000004
|
|
#define RXTX_REG127_FORCE_SUM_CAL_START_SET(dst, src) \
|
|
(((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
|
|
#define RXTX_REG127_FORCE_LAT_CAL_START_SET(dst, src) \
|
|
(((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
|
|
#define RXTX_REG127_LATCH_MAN_CAL_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008))
|
|
#define RXTX_REG127_DO_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
|
|
#define RXTX_REG127_XO_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
|
|
#define RXTX_REG128 0x100
|
|
#define RXTX_REG128_LATCH_CAL_WAIT_SEL_SET(dst, src) \
|
|
(((dst) & ~0x0000000c) | (((u32) (src) << 2) & 0x0000000c))
|
|
#define RXTX_REG128_EO_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
|
|
#define RXTX_REG128_SO_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
|
|
#define RXTX_REG129 0x102
|
|
#define RXTX_REG129_DE_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
|
|
#define RXTX_REG129_XE_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
|
|
#define RXTX_REG130 0x104
|
|
#define RXTX_REG130_EE_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00))
|
|
#define RXTX_REG130_SE_LATCH_MANCAL_SET(dst, src) \
|
|
(((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0))
|
|
#define RXTX_REG145 0x122
|
|
#define RXTX_REG145_TX_IDLE_SATA_SET(dst, src) \
|
|
(((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001))
|
|
#define RXTX_REG145_RXES_ENA_SET(dst, src) \
|
|
(((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002))
|
|
#define RXTX_REG145_RXDFE_CONFIG_SET(dst, src) \
|
|
(((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000))
|
|
#define RXTX_REG145_RXVWES_LATENA_SET(dst, src) \
|
|
(((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004))
|
|
#define RXTX_REG147 0x126
|
|
#define RXTX_REG148 0x128
|
|
|
|
/* Clock macro type */
|
|
enum cmu_type_t {
|
|
REF_CMU = 0, /* Clock macro is the internal reference clock */
|
|
PHY_CMU = 1, /* Clock macro is the PLL for the Serdes */
|
|
};
|
|
|
|
enum mux_type_t {
|
|
MUX_SELECT_ATA = 0, /* Switch the MUX to ATA */
|
|
MUX_SELECT_SGMMII = 0, /* Switch the MUX to SGMII */
|
|
};
|
|
|
|
enum clk_type_t {
|
|
CLK_EXT_DIFF = 0, /* External differential */
|
|
CLK_INT_DIFF = 1, /* Internal differential */
|
|
CLK_INT_SING = 2, /* Internal single ended */
|
|
};
|
|
|
|
enum xgene_phy_mode {
|
|
MODE_SATA = 0, /* List them for simple reference */
|
|
MODE_SGMII = 1,
|
|
MODE_PCIE = 2,
|
|
MODE_USB = 3,
|
|
MODE_XFI = 4,
|
|
MODE_MAX
|
|
};
|
|
|
|
struct xgene_sata_override_param {
|
|
u32 speed[MAX_LANE]; /* Index for override parameter per lane */
|
|
u32 txspeed[3]; /* Tx speed */
|
|
u32 txboostgain[MAX_LANE*3]; /* Tx freq boost and gain control */
|
|
u32 txeyetuning[MAX_LANE*3]; /* Tx eye tuning */
|
|
u32 txeyedirection[MAX_LANE*3]; /* Tx eye tuning direction */
|
|
u32 txamplitude[MAX_LANE*3]; /* Tx amplitude control */
|
|
u32 txprecursor_cn1[MAX_LANE*3]; /* Tx emphasis taps 1st pre-cursor */
|
|
u32 txprecursor_cn2[MAX_LANE*3]; /* Tx emphasis taps 2nd pre-cursor */
|
|
u32 txpostcursor_cp1[MAX_LANE*3]; /* Tx emphasis taps post-cursor */
|
|
};
|
|
|
|
struct xgene_phy_ctx {
|
|
struct device *dev;
|
|
struct phy *phy;
|
|
enum xgene_phy_mode mode; /* Mode of operation */
|
|
enum clk_type_t clk_type; /* Input clock selection */
|
|
void __iomem *sds_base; /* PHY CSR base addr */
|
|
struct clk *clk; /* Optional clock */
|
|
|
|
/* Override Serdes parameters */
|
|
struct xgene_sata_override_param sata_param;
|
|
};
|
|
|
|
/*
|
|
* For chip earlier than A3 version, enable this flag.
|
|
* To enable, pass boot argument phy_xgene.preA3Chip=1
|
|
*/
|
|
static int preA3Chip;
|
|
MODULE_PARM_DESC(preA3Chip, "Enable pre-A3 chip support (1=enable 0=disable)");
|
|
module_param_named(preA3Chip, preA3Chip, int, 0444);
|
|
|
|
static void sds_wr(void __iomem *csr_base, u32 indirect_cmd_reg,
|
|
u32 indirect_data_reg, u32 addr, u32 data)
|
|
{
|
|
unsigned long deadline = jiffies + HZ;
|
|
u32 val;
|
|
u32 cmd;
|
|
|
|
cmd = CFG_IND_WR_CMD_MASK | CFG_IND_CMD_DONE_MASK;
|
|
cmd = CFG_IND_ADDR_SET(cmd, addr);
|
|
writel(data, csr_base + indirect_data_reg);
|
|
readl(csr_base + indirect_data_reg); /* Force a barrier */
|
|
writel(cmd, csr_base + indirect_cmd_reg);
|
|
readl(csr_base + indirect_cmd_reg); /* Force a barrier */
|
|
do {
|
|
val = readl(csr_base + indirect_cmd_reg);
|
|
} while (!(val & CFG_IND_CMD_DONE_MASK) &&
|
|
time_before(jiffies, deadline));
|
|
if (!(val & CFG_IND_CMD_DONE_MASK))
|
|
pr_err("SDS WR timeout at 0x%p offset 0x%08X value 0x%08X\n",
|
|
csr_base + indirect_cmd_reg, addr, data);
|
|
}
|
|
|
|
static void sds_rd(void __iomem *csr_base, u32 indirect_cmd_reg,
|
|
u32 indirect_data_reg, u32 addr, u32 *data)
|
|
{
|
|
unsigned long deadline = jiffies + HZ;
|
|
u32 val;
|
|
u32 cmd;
|
|
|
|
cmd = CFG_IND_RD_CMD_MASK | CFG_IND_CMD_DONE_MASK;
|
|
cmd = CFG_IND_ADDR_SET(cmd, addr);
|
|
writel(cmd, csr_base + indirect_cmd_reg);
|
|
readl(csr_base + indirect_cmd_reg); /* Force a barrier */
|
|
do {
|
|
val = readl(csr_base + indirect_cmd_reg);
|
|
} while (!(val & CFG_IND_CMD_DONE_MASK) &&
|
|
time_before(jiffies, deadline));
|
|
*data = readl(csr_base + indirect_data_reg);
|
|
if (!(val & CFG_IND_CMD_DONE_MASK))
|
|
pr_err("SDS WR timeout at 0x%p offset 0x%08X value 0x%08X\n",
|
|
csr_base + indirect_cmd_reg, addr, *data);
|
|
}
|
|
|
|
static void cmu_wr(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
|
|
u32 reg, u32 data)
|
|
{
|
|
void __iomem *sds_base = ctx->sds_base;
|
|
u32 val;
|
|
|
|
if (cmu_type == REF_CMU)
|
|
reg += SERDES_PLL_REF_INDIRECT_OFFSET;
|
|
else
|
|
reg += SERDES_PLL_INDIRECT_OFFSET;
|
|
sds_wr(sds_base, SATA_ENET_SDS_IND_CMD_REG,
|
|
SATA_ENET_SDS_IND_WDATA_REG, reg, data);
|
|
sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
|
|
SATA_ENET_SDS_IND_RDATA_REG, reg, &val);
|
|
pr_debug("CMU WR addr 0x%X value 0x%08X <-> 0x%08X\n", reg, data, val);
|
|
}
|
|
|
|
static void cmu_rd(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
|
|
u32 reg, u32 *data)
|
|
{
|
|
void __iomem *sds_base = ctx->sds_base;
|
|
|
|
if (cmu_type == REF_CMU)
|
|
reg += SERDES_PLL_REF_INDIRECT_OFFSET;
|
|
else
|
|
reg += SERDES_PLL_INDIRECT_OFFSET;
|
|
sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
|
|
SATA_ENET_SDS_IND_RDATA_REG, reg, data);
|
|
pr_debug("CMU RD addr 0x%X value 0x%08X\n", reg, *data);
|
|
}
|
|
|
|
static void cmu_toggle1to0(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
|
|
u32 reg, u32 bits)
|
|
{
|
|
u32 val;
|
|
|
|
cmu_rd(ctx, cmu_type, reg, &val);
|
|
val |= bits;
|
|
cmu_wr(ctx, cmu_type, reg, val);
|
|
cmu_rd(ctx, cmu_type, reg, &val);
|
|
val &= ~bits;
|
|
cmu_wr(ctx, cmu_type, reg, val);
|
|
}
|
|
|
|
static void cmu_clrbits(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
|
|
u32 reg, u32 bits)
|
|
{
|
|
u32 val;
|
|
|
|
cmu_rd(ctx, cmu_type, reg, &val);
|
|
val &= ~bits;
|
|
cmu_wr(ctx, cmu_type, reg, val);
|
|
}
|
|
|
|
static void cmu_setbits(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type,
|
|
u32 reg, u32 bits)
|
|
{
|
|
u32 val;
|
|
|
|
cmu_rd(ctx, cmu_type, reg, &val);
|
|
val |= bits;
|
|
cmu_wr(ctx, cmu_type, reg, val);
|
|
}
|
|
|
|
static void serdes_wr(struct xgene_phy_ctx *ctx, int lane, u32 reg, u32 data)
|
|
{
|
|
void __iomem *sds_base = ctx->sds_base;
|
|
u32 val;
|
|
|
|
reg += SERDES_INDIRECT_OFFSET;
|
|
reg += lane * SERDES_LANE_STRIDE;
|
|
sds_wr(sds_base, SATA_ENET_SDS_IND_CMD_REG,
|
|
SATA_ENET_SDS_IND_WDATA_REG, reg, data);
|
|
sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
|
|
SATA_ENET_SDS_IND_RDATA_REG, reg, &val);
|
|
pr_debug("SERDES WR addr 0x%X value 0x%08X <-> 0x%08X\n", reg, data,
|
|
val);
|
|
}
|
|
|
|
static void serdes_rd(struct xgene_phy_ctx *ctx, int lane, u32 reg, u32 *data)
|
|
{
|
|
void __iomem *sds_base = ctx->sds_base;
|
|
|
|
reg += SERDES_INDIRECT_OFFSET;
|
|
reg += lane * SERDES_LANE_STRIDE;
|
|
sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG,
|
|
SATA_ENET_SDS_IND_RDATA_REG, reg, data);
|
|
pr_debug("SERDES RD addr 0x%X value 0x%08X\n", reg, *data);
|
|
}
|
|
|
|
static void serdes_clrbits(struct xgene_phy_ctx *ctx, int lane, u32 reg,
|
|
u32 bits)
|
|
{
|
|
u32 val;
|
|
|
|
serdes_rd(ctx, lane, reg, &val);
|
|
val &= ~bits;
|
|
serdes_wr(ctx, lane, reg, val);
|
|
}
|
|
|
|
static void serdes_setbits(struct xgene_phy_ctx *ctx, int lane, u32 reg,
|
|
u32 bits)
|
|
{
|
|
u32 val;
|
|
|
|
serdes_rd(ctx, lane, reg, &val);
|
|
val |= bits;
|
|
serdes_wr(ctx, lane, reg, val);
|
|
}
|
|
|
|
static void xgene_phy_cfg_cmu_clk_type(struct xgene_phy_ctx *ctx,
|
|
enum cmu_type_t cmu_type,
|
|
enum clk_type_t clk_type)
|
|
{
|
|
u32 val;
|
|
|
|
/* Set the reset sequence delay for TX ready assertion */
|
|
cmu_rd(ctx, cmu_type, CMU_REG12, &val);
|
|
val = CMU_REG12_STATE_DELAY9_SET(val, 0x1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG12, val);
|
|
/* Set the programmable stage delays between various enable stages */
|
|
cmu_wr(ctx, cmu_type, CMU_REG13, 0x0222);
|
|
cmu_wr(ctx, cmu_type, CMU_REG14, 0x2225);
|
|
|
|
/* Configure clock type */
|
|
if (clk_type == CLK_EXT_DIFF) {
|
|
/* Select external clock mux */
|
|
cmu_rd(ctx, cmu_type, CMU_REG0, &val);
|
|
val = CMU_REG0_PLL_REF_SEL_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG0, val);
|
|
/* Select CMOS as reference clock */
|
|
cmu_rd(ctx, cmu_type, CMU_REG1, &val);
|
|
val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG1, val);
|
|
dev_dbg(ctx->dev, "Set external reference clock\n");
|
|
} else if (clk_type == CLK_INT_DIFF) {
|
|
/* Select internal clock mux */
|
|
cmu_rd(ctx, cmu_type, CMU_REG0, &val);
|
|
val = CMU_REG0_PLL_REF_SEL_SET(val, 0x1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG0, val);
|
|
/* Select CMOS as reference clock */
|
|
cmu_rd(ctx, cmu_type, CMU_REG1, &val);
|
|
val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG1, val);
|
|
dev_dbg(ctx->dev, "Set internal reference clock\n");
|
|
} else if (clk_type == CLK_INT_SING) {
|
|
/*
|
|
* NOTE: This clock type is NOT support for controller
|
|
* whose internal clock shared in the PCIe controller
|
|
*
|
|
* Select internal clock mux
|
|
*/
|
|
cmu_rd(ctx, cmu_type, CMU_REG1, &val);
|
|
val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG1, val);
|
|
/* Select CML as reference clock */
|
|
cmu_rd(ctx, cmu_type, CMU_REG1, &val);
|
|
val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG1, val);
|
|
dev_dbg(ctx->dev,
|
|
"Set internal single ended reference clock\n");
|
|
}
|
|
}
|
|
|
|
static void xgene_phy_sata_cfg_cmu_core(struct xgene_phy_ctx *ctx,
|
|
enum cmu_type_t cmu_type,
|
|
enum clk_type_t clk_type)
|
|
{
|
|
u32 val;
|
|
int ref_100MHz;
|
|
|
|
if (cmu_type == REF_CMU) {
|
|
/* Set VCO calibration voltage threshold */
|
|
cmu_rd(ctx, cmu_type, CMU_REG34, &val);
|
|
val = CMU_REG34_VCO_CAL_VTH_LO_MAX_SET(val, 0x7);
|
|
val = CMU_REG34_VCO_CAL_VTH_HI_MAX_SET(val, 0xc);
|
|
val = CMU_REG34_VCO_CAL_VTH_LO_MIN_SET(val, 0x3);
|
|
val = CMU_REG34_VCO_CAL_VTH_HI_MIN_SET(val, 0x8);
|
|
cmu_wr(ctx, cmu_type, CMU_REG34, val);
|
|
}
|
|
|
|
/* Set the VCO calibration counter */
|
|
cmu_rd(ctx, cmu_type, CMU_REG0, &val);
|
|
if (cmu_type == REF_CMU || preA3Chip)
|
|
val = CMU_REG0_CAL_COUNT_RESOL_SET(val, 0x4);
|
|
else
|
|
val = CMU_REG0_CAL_COUNT_RESOL_SET(val, 0x7);
|
|
cmu_wr(ctx, cmu_type, CMU_REG0, val);
|
|
|
|
/* Configure PLL for calibration */
|
|
cmu_rd(ctx, cmu_type, CMU_REG1, &val);
|
|
val = CMU_REG1_PLL_CP_SET(val, 0x1);
|
|
if (cmu_type == REF_CMU || preA3Chip)
|
|
val = CMU_REG1_PLL_CP_SEL_SET(val, 0x5);
|
|
else
|
|
val = CMU_REG1_PLL_CP_SEL_SET(val, 0x3);
|
|
if (cmu_type == REF_CMU)
|
|
val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x0);
|
|
else
|
|
val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG1, val);
|
|
|
|
if (cmu_type != REF_CMU)
|
|
cmu_clrbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
|
|
|
|
/* Configure the PLL for either 100MHz or 50MHz */
|
|
cmu_rd(ctx, cmu_type, CMU_REG2, &val);
|
|
if (cmu_type == REF_CMU) {
|
|
val = CMU_REG2_PLL_LFRES_SET(val, 0xa);
|
|
ref_100MHz = 1;
|
|
} else {
|
|
val = CMU_REG2_PLL_LFRES_SET(val, 0x3);
|
|
if (clk_type == CLK_EXT_DIFF)
|
|
ref_100MHz = 0;
|
|
else
|
|
ref_100MHz = 1;
|
|
}
|
|
if (ref_100MHz) {
|
|
val = CMU_REG2_PLL_FBDIV_SET(val, FBDIV_VAL_100M);
|
|
val = CMU_REG2_PLL_REFDIV_SET(val, REFDIV_VAL_100M);
|
|
} else {
|
|
val = CMU_REG2_PLL_FBDIV_SET(val, FBDIV_VAL_50M);
|
|
val = CMU_REG2_PLL_REFDIV_SET(val, REFDIV_VAL_50M);
|
|
}
|
|
cmu_wr(ctx, cmu_type, CMU_REG2, val);
|
|
|
|
/* Configure the VCO */
|
|
cmu_rd(ctx, cmu_type, CMU_REG3, &val);
|
|
if (cmu_type == REF_CMU) {
|
|
val = CMU_REG3_VCOVARSEL_SET(val, 0x3);
|
|
val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x10);
|
|
} else {
|
|
val = CMU_REG3_VCOVARSEL_SET(val, 0xF);
|
|
if (preA3Chip)
|
|
val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x15);
|
|
else
|
|
val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x1a);
|
|
val = CMU_REG3_VCO_MANMOMSEL_SET(val, 0x15);
|
|
}
|
|
cmu_wr(ctx, cmu_type, CMU_REG3, val);
|
|
|
|
/* Disable force PLL lock */
|
|
cmu_rd(ctx, cmu_type, CMU_REG26, &val);
|
|
val = CMU_REG26_FORCE_PLL_LOCK_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG26, val);
|
|
|
|
/* Setup PLL loop filter */
|
|
cmu_rd(ctx, cmu_type, CMU_REG5, &val);
|
|
val = CMU_REG5_PLL_LFSMCAP_SET(val, 0x3);
|
|
val = CMU_REG5_PLL_LFCAP_SET(val, 0x3);
|
|
if (cmu_type == REF_CMU || !preA3Chip)
|
|
val = CMU_REG5_PLL_LOCK_RESOLUTION_SET(val, 0x7);
|
|
else
|
|
val = CMU_REG5_PLL_LOCK_RESOLUTION_SET(val, 0x4);
|
|
cmu_wr(ctx, cmu_type, CMU_REG5, val);
|
|
|
|
/* Enable or disable manual calibration */
|
|
cmu_rd(ctx, cmu_type, CMU_REG6, &val);
|
|
val = CMU_REG6_PLL_VREGTRIM_SET(val, preA3Chip ? 0x0 : 0x2);
|
|
val = CMU_REG6_MAN_PVT_CAL_SET(val, preA3Chip ? 0x1 : 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG6, val);
|
|
|
|
/* Configure lane for 20-bits */
|
|
if (cmu_type == PHY_CMU) {
|
|
cmu_rd(ctx, cmu_type, CMU_REG9, &val);
|
|
val = CMU_REG9_TX_WORD_MODE_CH1_SET(val,
|
|
CMU_REG9_WORD_LEN_20BIT);
|
|
val = CMU_REG9_TX_WORD_MODE_CH0_SET(val,
|
|
CMU_REG9_WORD_LEN_20BIT);
|
|
val = CMU_REG9_PLL_POST_DIVBY2_SET(val, 0x1);
|
|
if (!preA3Chip) {
|
|
val = CMU_REG9_VBG_BYPASSB_SET(val, 0x0);
|
|
val = CMU_REG9_IGEN_BYPASS_SET(val , 0x0);
|
|
}
|
|
cmu_wr(ctx, cmu_type, CMU_REG9, val);
|
|
|
|
if (!preA3Chip) {
|
|
cmu_rd(ctx, cmu_type, CMU_REG10, &val);
|
|
val = CMU_REG10_VREG_REFSEL_SET(val, 0x1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG10, val);
|
|
}
|
|
}
|
|
|
|
cmu_rd(ctx, cmu_type, CMU_REG16, &val);
|
|
val = CMU_REG16_CALIBRATION_DONE_OVERRIDE_SET(val, 0x1);
|
|
val = CMU_REG16_BYPASS_PLL_LOCK_SET(val, 0x1);
|
|
if (cmu_type == REF_CMU || preA3Chip)
|
|
val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x4);
|
|
else
|
|
val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x7);
|
|
cmu_wr(ctx, cmu_type, CMU_REG16, val);
|
|
|
|
/* Configure for SATA */
|
|
cmu_rd(ctx, cmu_type, CMU_REG30, &val);
|
|
val = CMU_REG30_PCIE_MODE_SET(val, 0x0);
|
|
val = CMU_REG30_LOCK_COUNT_SET(val, 0x3);
|
|
cmu_wr(ctx, cmu_type, CMU_REG30, val);
|
|
|
|
/* Disable state machine bypass */
|
|
cmu_wr(ctx, cmu_type, CMU_REG31, 0xF);
|
|
|
|
cmu_rd(ctx, cmu_type, CMU_REG32, &val);
|
|
val = CMU_REG32_PVT_CAL_WAIT_SEL_SET(val, 0x3);
|
|
if (cmu_type == REF_CMU || preA3Chip)
|
|
val = CMU_REG32_IREF_ADJ_SET(val, 0x3);
|
|
else
|
|
val = CMU_REG32_IREF_ADJ_SET(val, 0x1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG32, val);
|
|
|
|
/* Set VCO calibration threshold */
|
|
if (cmu_type != REF_CMU && preA3Chip)
|
|
cmu_wr(ctx, cmu_type, CMU_REG34, 0x8d27);
|
|
else
|
|
cmu_wr(ctx, cmu_type, CMU_REG34, 0x873c);
|
|
|
|
/* Set CTLE Override and override waiting from state machine */
|
|
cmu_wr(ctx, cmu_type, CMU_REG37, 0xF00F);
|
|
}
|
|
|
|
static void xgene_phy_ssc_enable(struct xgene_phy_ctx *ctx,
|
|
enum cmu_type_t cmu_type)
|
|
{
|
|
u32 val;
|
|
|
|
/* Set SSC modulation value */
|
|
cmu_rd(ctx, cmu_type, CMU_REG35, &val);
|
|
val = CMU_REG35_PLL_SSC_MOD_SET(val, 98);
|
|
cmu_wr(ctx, cmu_type, CMU_REG35, val);
|
|
|
|
/* Enable SSC, set vertical step and DSM value */
|
|
cmu_rd(ctx, cmu_type, CMU_REG36, &val);
|
|
val = CMU_REG36_PLL_SSC_VSTEP_SET(val, 30);
|
|
val = CMU_REG36_PLL_SSC_EN_SET(val, 1);
|
|
val = CMU_REG36_PLL_SSC_DSMSEL_SET(val, 1);
|
|
cmu_wr(ctx, cmu_type, CMU_REG36, val);
|
|
|
|
/* Reset the PLL */
|
|
cmu_clrbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
|
|
cmu_setbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
|
|
|
|
/* Force VCO calibration to restart */
|
|
cmu_toggle1to0(ctx, cmu_type, CMU_REG32,
|
|
CMU_REG32_FORCE_VCOCAL_START_MASK);
|
|
}
|
|
|
|
static void xgene_phy_sata_cfg_lanes(struct xgene_phy_ctx *ctx)
|
|
{
|
|
u32 val;
|
|
u32 reg;
|
|
int i;
|
|
int lane;
|
|
|
|
for (lane = 0; lane < MAX_LANE; lane++) {
|
|
serdes_wr(ctx, lane, RXTX_REG147, 0x6);
|
|
|
|
/* Set boost control for quarter, half, and full rate */
|
|
serdes_rd(ctx, lane, RXTX_REG0, &val);
|
|
val = RXTX_REG0_CTLE_EQ_HR_SET(val, 0x10);
|
|
val = RXTX_REG0_CTLE_EQ_QR_SET(val, 0x10);
|
|
val = RXTX_REG0_CTLE_EQ_FR_SET(val, 0x10);
|
|
serdes_wr(ctx, lane, RXTX_REG0, val);
|
|
|
|
/* Set boost control value */
|
|
serdes_rd(ctx, lane, RXTX_REG1, &val);
|
|
val = RXTX_REG1_RXACVCM_SET(val, 0x7);
|
|
val = RXTX_REG1_CTLE_EQ_SET(val,
|
|
ctx->sata_param.txboostgain[lane * 3 +
|
|
ctx->sata_param.speed[lane]]);
|
|
serdes_wr(ctx, lane, RXTX_REG1, val);
|
|
|
|
/* Latch VTT value based on the termination to ground and
|
|
enable TX FIFO */
|
|
serdes_rd(ctx, lane, RXTX_REG2, &val);
|
|
val = RXTX_REG2_VTT_ENA_SET(val, 0x1);
|
|
val = RXTX_REG2_VTT_SEL_SET(val, 0x1);
|
|
val = RXTX_REG2_TX_FIFO_ENA_SET(val, 0x1);
|
|
serdes_wr(ctx, lane, RXTX_REG2, val);
|
|
|
|
/* Configure Tx for 20-bits */
|
|
serdes_rd(ctx, lane, RXTX_REG4, &val);
|
|
val = RXTX_REG4_TX_WORD_MODE_SET(val, CMU_REG9_WORD_LEN_20BIT);
|
|
serdes_wr(ctx, lane, RXTX_REG4, val);
|
|
|
|
if (!preA3Chip) {
|
|
serdes_rd(ctx, lane, RXTX_REG1, &val);
|
|
val = RXTX_REG1_RXVREG1_SET(val, 0x2);
|
|
val = RXTX_REG1_RXIREF_ADJ_SET(val, 0x2);
|
|
serdes_wr(ctx, lane, RXTX_REG1, val);
|
|
}
|
|
|
|
/* Set pre-emphasis first 1 and 2, and post-emphasis values */
|
|
serdes_rd(ctx, lane, RXTX_REG5, &val);
|
|
val = RXTX_REG5_TX_CN1_SET(val,
|
|
ctx->sata_param.txprecursor_cn1[lane * 3 +
|
|
ctx->sata_param.speed[lane]]);
|
|
val = RXTX_REG5_TX_CP1_SET(val,
|
|
ctx->sata_param.txpostcursor_cp1[lane * 3 +
|
|
ctx->sata_param.speed[lane]]);
|
|
val = RXTX_REG5_TX_CN2_SET(val,
|
|
ctx->sata_param.txprecursor_cn2[lane * 3 +
|
|
ctx->sata_param.speed[lane]]);
|
|
serdes_wr(ctx, lane, RXTX_REG5, val);
|
|
|
|
/* Set TX amplitude value */
|
|
serdes_rd(ctx, lane, RXTX_REG6, &val);
|
|
val = RXTX_REG6_TXAMP_CNTL_SET(val,
|
|
ctx->sata_param.txamplitude[lane * 3 +
|
|
ctx->sata_param.speed[lane]]);
|
|
val = RXTX_REG6_TXAMP_ENA_SET(val, 0x1);
|
|
val = RXTX_REG6_TX_IDLE_SET(val, 0x0);
|
|
val = RXTX_REG6_RX_BIST_RESYNC_SET(val, 0x0);
|
|
val = RXTX_REG6_RX_BIST_ERRCNT_RD_SET(val, 0x0);
|
|
serdes_wr(ctx, lane, RXTX_REG6, val);
|
|
|
|
/* Configure Rx for 20-bits */
|
|
serdes_rd(ctx, lane, RXTX_REG7, &val);
|
|
val = RXTX_REG7_BIST_ENA_RX_SET(val, 0x0);
|
|
val = RXTX_REG7_RX_WORD_MODE_SET(val, CMU_REG9_WORD_LEN_20BIT);
|
|
serdes_wr(ctx, lane, RXTX_REG7, val);
|
|
|
|
/* Set CDR and LOS values and enable Rx SSC */
|
|
serdes_rd(ctx, lane, RXTX_REG8, &val);
|
|
val = RXTX_REG8_CDR_LOOP_ENA_SET(val, 0x1);
|
|
val = RXTX_REG8_CDR_BYPASS_RXLOS_SET(val, 0x0);
|
|
val = RXTX_REG8_SSC_ENABLE_SET(val, 0x1);
|
|
val = RXTX_REG8_SD_DISABLE_SET(val, 0x0);
|
|
val = RXTX_REG8_SD_VREF_SET(val, 0x4);
|
|
serdes_wr(ctx, lane, RXTX_REG8, val);
|
|
|
|
/* Set phase adjust upper/lower limits */
|
|
serdes_rd(ctx, lane, RXTX_REG11, &val);
|
|
val = RXTX_REG11_PHASE_ADJUST_LIMIT_SET(val, 0x0);
|
|
serdes_wr(ctx, lane, RXTX_REG11, val);
|
|
|
|
/* Enable Latch Off; disable SUMOS and Tx termination */
|
|
serdes_rd(ctx, lane, RXTX_REG12, &val);
|
|
val = RXTX_REG12_LATCH_OFF_ENA_SET(val, 0x1);
|
|
val = RXTX_REG12_SUMOS_ENABLE_SET(val, 0x0);
|
|
val = RXTX_REG12_RX_DET_TERM_ENABLE_SET(val, 0x0);
|
|
serdes_wr(ctx, lane, RXTX_REG12, val);
|
|
|
|
/* Set period error latch to 512T and enable BWL */
|
|
serdes_rd(ctx, lane, RXTX_REG26, &val);
|
|
val = RXTX_REG26_PERIOD_ERROR_LATCH_SET(val, 0x0);
|
|
val = RXTX_REG26_BLWC_ENA_SET(val, 0x1);
|
|
serdes_wr(ctx, lane, RXTX_REG26, val);
|
|
|
|
serdes_wr(ctx, lane, RXTX_REG28, 0x0);
|
|
|
|
/* Set DFE loop preset value */
|
|
serdes_wr(ctx, lane, RXTX_REG31, 0x0);
|
|
|
|
/* Set Eye Monitor counter width to 12-bit */
|
|
serdes_rd(ctx, lane, RXTX_REG61, &val);
|
|
val = RXTX_REG61_ISCAN_INBERT_SET(val, 0x1);
|
|
val = RXTX_REG61_LOADFREQ_SHIFT_SET(val, 0x0);
|
|
val = RXTX_REG61_EYE_COUNT_WIDTH_SEL_SET(val, 0x0);
|
|
serdes_wr(ctx, lane, RXTX_REG61, val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG62, &val);
|
|
val = RXTX_REG62_PERIOD_H1_QLATCH_SET(val, 0x0);
|
|
serdes_wr(ctx, lane, RXTX_REG62, val);
|
|
|
|
/* Set BW select tap X for DFE loop */
|
|
for (i = 0; i < 9; i++) {
|
|
reg = RXTX_REG81 + i * 2;
|
|
serdes_rd(ctx, lane, reg, &val);
|
|
val = RXTX_REG89_MU_TH7_SET(val, 0xe);
|
|
val = RXTX_REG89_MU_TH8_SET(val, 0xe);
|
|
val = RXTX_REG89_MU_TH9_SET(val, 0xe);
|
|
serdes_wr(ctx, lane, reg, val);
|
|
}
|
|
|
|
/* Set BW select tap X for frequency adjust loop */
|
|
for (i = 0; i < 3; i++) {
|
|
reg = RXTX_REG96 + i * 2;
|
|
serdes_rd(ctx, lane, reg, &val);
|
|
val = RXTX_REG96_MU_FREQ1_SET(val, 0x10);
|
|
val = RXTX_REG96_MU_FREQ2_SET(val, 0x10);
|
|
val = RXTX_REG96_MU_FREQ3_SET(val, 0x10);
|
|
serdes_wr(ctx, lane, reg, val);
|
|
}
|
|
|
|
/* Set BW select tap X for phase adjust loop */
|
|
for (i = 0; i < 3; i++) {
|
|
reg = RXTX_REG99 + i * 2;
|
|
serdes_rd(ctx, lane, reg, &val);
|
|
val = RXTX_REG99_MU_PHASE1_SET(val, 0x7);
|
|
val = RXTX_REG99_MU_PHASE2_SET(val, 0x7);
|
|
val = RXTX_REG99_MU_PHASE3_SET(val, 0x7);
|
|
serdes_wr(ctx, lane, reg, val);
|
|
}
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG102, &val);
|
|
val = RXTX_REG102_FREQLOOP_LIMIT_SET(val, 0x0);
|
|
serdes_wr(ctx, lane, RXTX_REG102, val);
|
|
|
|
serdes_wr(ctx, lane, RXTX_REG114, 0xffe0);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG125, &val);
|
|
val = RXTX_REG125_SIGN_PQ_SET(val,
|
|
ctx->sata_param.txeyedirection[lane * 3 +
|
|
ctx->sata_param.speed[lane]]);
|
|
val = RXTX_REG125_PQ_REG_SET(val,
|
|
ctx->sata_param.txeyetuning[lane * 3 +
|
|
ctx->sata_param.speed[lane]]);
|
|
val = RXTX_REG125_PHZ_MANUAL_SET(val, 0x1);
|
|
serdes_wr(ctx, lane, RXTX_REG125, val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG127, &val);
|
|
val = RXTX_REG127_LATCH_MAN_CAL_ENA_SET(val, 0x0);
|
|
serdes_wr(ctx, lane, RXTX_REG127, val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG128, &val);
|
|
val = RXTX_REG128_LATCH_CAL_WAIT_SEL_SET(val, 0x3);
|
|
serdes_wr(ctx, lane, RXTX_REG128, val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG145, &val);
|
|
val = RXTX_REG145_RXDFE_CONFIG_SET(val, 0x3);
|
|
val = RXTX_REG145_TX_IDLE_SATA_SET(val, 0x0);
|
|
if (preA3Chip) {
|
|
val = RXTX_REG145_RXES_ENA_SET(val, 0x1);
|
|
val = RXTX_REG145_RXVWES_LATENA_SET(val, 0x1);
|
|
} else {
|
|
val = RXTX_REG145_RXES_ENA_SET(val, 0x0);
|
|
val = RXTX_REG145_RXVWES_LATENA_SET(val, 0x0);
|
|
}
|
|
serdes_wr(ctx, lane, RXTX_REG145, val);
|
|
|
|
/*
|
|
* Set Rx LOS filter clock rate, sample rate, and threshold
|
|
* windows
|
|
*/
|
|
for (i = 0; i < 4; i++) {
|
|
reg = RXTX_REG148 + i * 2;
|
|
serdes_wr(ctx, lane, reg, 0xFFFF);
|
|
}
|
|
}
|
|
}
|
|
|
|
static int xgene_phy_cal_rdy_chk(struct xgene_phy_ctx *ctx,
|
|
enum cmu_type_t cmu_type,
|
|
enum clk_type_t clk_type)
|
|
{
|
|
void __iomem *csr_serdes = ctx->sds_base;
|
|
int loop;
|
|
u32 val;
|
|
|
|
/* Release PHY main reset */
|
|
writel(0xdf, csr_serdes + SATA_ENET_SDS_RST_CTL);
|
|
readl(csr_serdes + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
|
|
|
|
if (cmu_type != REF_CMU) {
|
|
cmu_setbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK);
|
|
/*
|
|
* As per PHY design spec, the PLL reset requires a minimum
|
|
* of 800us.
|
|
*/
|
|
usleep_range(800, 1000);
|
|
|
|
cmu_rd(ctx, cmu_type, CMU_REG1, &val);
|
|
val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG1, val);
|
|
/*
|
|
* As per PHY design spec, the PLL auto calibration requires
|
|
* a minimum of 800us.
|
|
*/
|
|
usleep_range(800, 1000);
|
|
|
|
cmu_toggle1to0(ctx, cmu_type, CMU_REG32,
|
|
CMU_REG32_FORCE_VCOCAL_START_MASK);
|
|
/*
|
|
* As per PHY design spec, the PLL requires a minimum of
|
|
* 800us to settle.
|
|
*/
|
|
usleep_range(800, 1000);
|
|
}
|
|
|
|
if (!preA3Chip)
|
|
goto skip_manual_cal;
|
|
|
|
/*
|
|
* Configure the termination resister calibration
|
|
* The serial receive pins, RXP/RXN, have TERMination resistor
|
|
* that is required to be calibrated.
|
|
*/
|
|
cmu_rd(ctx, cmu_type, CMU_REG17, &val);
|
|
val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x12);
|
|
val = CMU_REG17_RESERVED_7_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG17, val);
|
|
cmu_toggle1to0(ctx, cmu_type, CMU_REG17,
|
|
CMU_REG17_PVT_TERM_MAN_ENA_MASK);
|
|
/*
|
|
* The serial transmit pins, TXP/TXN, have Pull-UP and Pull-DOWN
|
|
* resistors that are required to the calibrated.
|
|
* Configure the pull DOWN calibration
|
|
*/
|
|
cmu_rd(ctx, cmu_type, CMU_REG17, &val);
|
|
val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x29);
|
|
val = CMU_REG17_RESERVED_7_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG17, val);
|
|
cmu_toggle1to0(ctx, cmu_type, CMU_REG16,
|
|
CMU_REG16_PVT_DN_MAN_ENA_MASK);
|
|
/* Configure the pull UP calibration */
|
|
cmu_rd(ctx, cmu_type, CMU_REG17, &val);
|
|
val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x28);
|
|
val = CMU_REG17_RESERVED_7_SET(val, 0x0);
|
|
cmu_wr(ctx, cmu_type, CMU_REG17, val);
|
|
cmu_toggle1to0(ctx, cmu_type, CMU_REG16,
|
|
CMU_REG16_PVT_UP_MAN_ENA_MASK);
|
|
|
|
skip_manual_cal:
|
|
/* Poll the PLL calibration completion status for at least 1 ms */
|
|
loop = 100;
|
|
do {
|
|
cmu_rd(ctx, cmu_type, CMU_REG7, &val);
|
|
if (CMU_REG7_PLL_CALIB_DONE_RD(val))
|
|
break;
|
|
/*
|
|
* As per PHY design spec, PLL calibration status requires
|
|
* a minimum of 10us to be updated.
|
|
*/
|
|
usleep_range(10, 100);
|
|
} while (--loop > 0);
|
|
|
|
cmu_rd(ctx, cmu_type, CMU_REG7, &val);
|
|
dev_dbg(ctx->dev, "PLL calibration %s\n",
|
|
CMU_REG7_PLL_CALIB_DONE_RD(val) ? "done" : "failed");
|
|
if (CMU_REG7_VCO_CAL_FAIL_RD(val)) {
|
|
dev_err(ctx->dev,
|
|
"PLL calibration failed due to VCO failure\n");
|
|
return -1;
|
|
}
|
|
dev_dbg(ctx->dev, "PLL calibration successful\n");
|
|
|
|
cmu_rd(ctx, cmu_type, CMU_REG15, &val);
|
|
dev_dbg(ctx->dev, "PHY Tx is %sready\n", val & 0x300 ? "" : "not ");
|
|
return 0;
|
|
}
|
|
|
|
static void xgene_phy_pdwn_force_vco(struct xgene_phy_ctx *ctx,
|
|
enum cmu_type_t cmu_type,
|
|
enum clk_type_t clk_type)
|
|
{
|
|
u32 val;
|
|
|
|
dev_dbg(ctx->dev, "Reset VCO and re-start again\n");
|
|
if (cmu_type == PHY_CMU) {
|
|
cmu_rd(ctx, cmu_type, CMU_REG16, &val);
|
|
val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x7);
|
|
cmu_wr(ctx, cmu_type, CMU_REG16, val);
|
|
}
|
|
|
|
cmu_toggle1to0(ctx, cmu_type, CMU_REG0, CMU_REG0_PDOWN_MASK);
|
|
cmu_toggle1to0(ctx, cmu_type, CMU_REG32,
|
|
CMU_REG32_FORCE_VCOCAL_START_MASK);
|
|
}
|
|
|
|
static int xgene_phy_hw_init_sata(struct xgene_phy_ctx *ctx,
|
|
enum clk_type_t clk_type, int ssc_enable)
|
|
{
|
|
void __iomem *sds_base = ctx->sds_base;
|
|
u32 val;
|
|
int i;
|
|
|
|
/* Configure the PHY for operation */
|
|
dev_dbg(ctx->dev, "Reset PHY\n");
|
|
/* Place PHY into reset */
|
|
writel(0x0, sds_base + SATA_ENET_SDS_RST_CTL);
|
|
val = readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
|
|
/* Release PHY lane from reset (active high) */
|
|
writel(0x20, sds_base + SATA_ENET_SDS_RST_CTL);
|
|
readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
|
|
/* Release all PHY module out of reset except PHY main reset */
|
|
writel(0xde, sds_base + SATA_ENET_SDS_RST_CTL);
|
|
readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */
|
|
|
|
/* Set the operation speed */
|
|
val = readl(sds_base + SATA_ENET_SDS_CTL1);
|
|
val = CFG_I_SPD_SEL_CDR_OVR1_SET(val,
|
|
ctx->sata_param.txspeed[ctx->sata_param.speed[0]]);
|
|
writel(val, sds_base + SATA_ENET_SDS_CTL1);
|
|
|
|
dev_dbg(ctx->dev, "Set the customer pin mode to SATA\n");
|
|
val = readl(sds_base + SATA_ENET_SDS_CTL0);
|
|
val = REGSPEC_CFG_I_CUSTOMER_PIN_MODE0_SET(val, 0x4421);
|
|
writel(val, sds_base + SATA_ENET_SDS_CTL0);
|
|
|
|
/* Configure the clock macro unit (CMU) clock type */
|
|
xgene_phy_cfg_cmu_clk_type(ctx, PHY_CMU, clk_type);
|
|
|
|
/* Configure the clock macro */
|
|
xgene_phy_sata_cfg_cmu_core(ctx, PHY_CMU, clk_type);
|
|
|
|
/* Enable SSC if enabled */
|
|
if (ssc_enable)
|
|
xgene_phy_ssc_enable(ctx, PHY_CMU);
|
|
|
|
/* Configure PHY lanes */
|
|
xgene_phy_sata_cfg_lanes(ctx);
|
|
|
|
/* Set Rx/Tx 20-bit */
|
|
val = readl(sds_base + SATA_ENET_SDS_PCS_CTL0);
|
|
val = REGSPEC_CFG_I_RX_WORDMODE0_SET(val, 0x3);
|
|
val = REGSPEC_CFG_I_TX_WORDMODE0_SET(val, 0x3);
|
|
writel(val, sds_base + SATA_ENET_SDS_PCS_CTL0);
|
|
|
|
/* Start PLL calibration and try for three times */
|
|
i = 10;
|
|
do {
|
|
if (!xgene_phy_cal_rdy_chk(ctx, PHY_CMU, clk_type))
|
|
break;
|
|
/* If failed, toggle the VCO power signal and start again */
|
|
xgene_phy_pdwn_force_vco(ctx, PHY_CMU, clk_type);
|
|
} while (--i > 0);
|
|
/* Even on failure, allow to continue any way */
|
|
if (i <= 0)
|
|
dev_err(ctx->dev, "PLL calibration failed\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int xgene_phy_hw_initialize(struct xgene_phy_ctx *ctx,
|
|
enum clk_type_t clk_type,
|
|
int ssc_enable)
|
|
{
|
|
int rc;
|
|
|
|
dev_dbg(ctx->dev, "PHY init clk type %d\n", clk_type);
|
|
|
|
if (ctx->mode == MODE_SATA) {
|
|
rc = xgene_phy_hw_init_sata(ctx, clk_type, ssc_enable);
|
|
if (rc)
|
|
return rc;
|
|
} else {
|
|
dev_err(ctx->dev, "Un-supported customer pin mode %d\n",
|
|
ctx->mode);
|
|
return -ENODEV;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Receiver Offset Calibration:
|
|
*
|
|
* Calibrate the receiver signal path offset in two steps - summar and
|
|
* latch calibrations
|
|
*/
|
|
static void xgene_phy_force_lat_summer_cal(struct xgene_phy_ctx *ctx, int lane)
|
|
{
|
|
int i;
|
|
struct {
|
|
u32 reg;
|
|
u32 val;
|
|
} serdes_reg[] = {
|
|
{RXTX_REG38, 0x0},
|
|
{RXTX_REG39, 0xff00},
|
|
{RXTX_REG40, 0xffff},
|
|
{RXTX_REG41, 0xffff},
|
|
{RXTX_REG42, 0xffff},
|
|
{RXTX_REG43, 0xffff},
|
|
{RXTX_REG44, 0xffff},
|
|
{RXTX_REG45, 0xffff},
|
|
{RXTX_REG46, 0xffff},
|
|
{RXTX_REG47, 0xfffc},
|
|
{RXTX_REG48, 0x0},
|
|
{RXTX_REG49, 0x0},
|
|
{RXTX_REG50, 0x0},
|
|
{RXTX_REG51, 0x0},
|
|
{RXTX_REG52, 0x0},
|
|
{RXTX_REG53, 0x0},
|
|
{RXTX_REG54, 0x0},
|
|
{RXTX_REG55, 0x0},
|
|
};
|
|
|
|
/* Start SUMMER calibration */
|
|
serdes_setbits(ctx, lane, RXTX_REG127,
|
|
RXTX_REG127_FORCE_SUM_CAL_START_MASK);
|
|
/*
|
|
* As per PHY design spec, the Summer calibration requires a minimum
|
|
* of 100us to complete.
|
|
*/
|
|
usleep_range(100, 500);
|
|
serdes_clrbits(ctx, lane, RXTX_REG127,
|
|
RXTX_REG127_FORCE_SUM_CAL_START_MASK);
|
|
/*
|
|
* As per PHY design spec, the auto calibration requires a minimum
|
|
* of 100us to complete.
|
|
*/
|
|
usleep_range(100, 500);
|
|
|
|
/* Start latch calibration */
|
|
serdes_setbits(ctx, lane, RXTX_REG127,
|
|
RXTX_REG127_FORCE_LAT_CAL_START_MASK);
|
|
/*
|
|
* As per PHY design spec, the latch calibration requires a minimum
|
|
* of 100us to complete.
|
|
*/
|
|
usleep_range(100, 500);
|
|
serdes_clrbits(ctx, lane, RXTX_REG127,
|
|
RXTX_REG127_FORCE_LAT_CAL_START_MASK);
|
|
|
|
/* Configure the PHY lane for calibration */
|
|
serdes_wr(ctx, lane, RXTX_REG28, 0x7);
|
|
serdes_wr(ctx, lane, RXTX_REG31, 0x7e00);
|
|
serdes_clrbits(ctx, lane, RXTX_REG4,
|
|
RXTX_REG4_TX_LOOPBACK_BUF_EN_MASK);
|
|
serdes_clrbits(ctx, lane, RXTX_REG7,
|
|
RXTX_REG7_LOOP_BACK_ENA_CTLE_MASK);
|
|
for (i = 0; i < ARRAY_SIZE(serdes_reg); i++)
|
|
serdes_wr(ctx, lane, serdes_reg[i].reg,
|
|
serdes_reg[i].val);
|
|
}
|
|
|
|
static void xgene_phy_reset_rxd(struct xgene_phy_ctx *ctx, int lane)
|
|
{
|
|
/* Reset digital Rx */
|
|
serdes_clrbits(ctx, lane, RXTX_REG7, RXTX_REG7_RESETB_RXD_MASK);
|
|
/* As per PHY design spec, the reset requires a minimum of 100us. */
|
|
usleep_range(100, 150);
|
|
serdes_setbits(ctx, lane, RXTX_REG7, RXTX_REG7_RESETB_RXD_MASK);
|
|
}
|
|
|
|
static int xgene_phy_get_avg(int accum, int samples)
|
|
{
|
|
return (accum + (samples / 2)) / samples;
|
|
}
|
|
|
|
static void xgene_phy_gen_avg_val(struct xgene_phy_ctx *ctx, int lane)
|
|
{
|
|
int max_loop = 10;
|
|
int avg_loop = 0;
|
|
int lat_do = 0, lat_xo = 0, lat_eo = 0, lat_so = 0;
|
|
int lat_de = 0, lat_xe = 0, lat_ee = 0, lat_se = 0;
|
|
int sum_cal = 0;
|
|
int lat_do_itr, lat_xo_itr, lat_eo_itr, lat_so_itr;
|
|
int lat_de_itr, lat_xe_itr, lat_ee_itr, lat_se_itr;
|
|
int sum_cal_itr;
|
|
int fail_even;
|
|
int fail_odd;
|
|
u32 val;
|
|
|
|
dev_dbg(ctx->dev, "Generating avg calibration value for lane %d\n",
|
|
lane);
|
|
|
|
/* Enable RX Hi-Z termination */
|
|
serdes_setbits(ctx, lane, RXTX_REG12,
|
|
RXTX_REG12_RX_DET_TERM_ENABLE_MASK);
|
|
/* Turn off DFE */
|
|
serdes_wr(ctx, lane, RXTX_REG28, 0x0000);
|
|
/* DFE Presets to zero */
|
|
serdes_wr(ctx, lane, RXTX_REG31, 0x0000);
|
|
|
|
/*
|
|
* Receiver Offset Calibration:
|
|
* Calibrate the receiver signal path offset in two steps - summar
|
|
* and latch calibration.
|
|
* Runs the "Receiver Offset Calibration multiple times to determine
|
|
* the average value to use.
|
|
*/
|
|
while (avg_loop < max_loop) {
|
|
/* Start the calibration */
|
|
xgene_phy_force_lat_summer_cal(ctx, lane);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG21, &val);
|
|
lat_do_itr = RXTX_REG21_DO_LATCH_CALOUT_RD(val);
|
|
lat_xo_itr = RXTX_REG21_XO_LATCH_CALOUT_RD(val);
|
|
fail_odd = RXTX_REG21_LATCH_CAL_FAIL_ODD_RD(val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG22, &val);
|
|
lat_eo_itr = RXTX_REG22_EO_LATCH_CALOUT_RD(val);
|
|
lat_so_itr = RXTX_REG22_SO_LATCH_CALOUT_RD(val);
|
|
fail_even = RXTX_REG22_LATCH_CAL_FAIL_EVEN_RD(val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG23, &val);
|
|
lat_de_itr = RXTX_REG23_DE_LATCH_CALOUT_RD(val);
|
|
lat_xe_itr = RXTX_REG23_XE_LATCH_CALOUT_RD(val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG24, &val);
|
|
lat_ee_itr = RXTX_REG24_EE_LATCH_CALOUT_RD(val);
|
|
lat_se_itr = RXTX_REG24_SE_LATCH_CALOUT_RD(val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG121, &val);
|
|
sum_cal_itr = RXTX_REG121_SUMOS_CAL_CODE_RD(val);
|
|
|
|
/* Check for failure. If passed, sum them for averaging */
|
|
if ((fail_even == 0 || fail_even == 1) &&
|
|
(fail_odd == 0 || fail_odd == 1)) {
|
|
lat_do += lat_do_itr;
|
|
lat_xo += lat_xo_itr;
|
|
lat_eo += lat_eo_itr;
|
|
lat_so += lat_so_itr;
|
|
lat_de += lat_de_itr;
|
|
lat_xe += lat_xe_itr;
|
|
lat_ee += lat_ee_itr;
|
|
lat_se += lat_se_itr;
|
|
sum_cal += sum_cal_itr;
|
|
|
|
dev_dbg(ctx->dev, "Iteration %d:\n", avg_loop);
|
|
dev_dbg(ctx->dev, "DO 0x%x XO 0x%x EO 0x%x SO 0x%x\n",
|
|
lat_do_itr, lat_xo_itr, lat_eo_itr,
|
|
lat_so_itr);
|
|
dev_dbg(ctx->dev, "DE 0x%x XE 0x%x EE 0x%x SE 0x%x\n",
|
|
lat_de_itr, lat_xe_itr, lat_ee_itr,
|
|
lat_se_itr);
|
|
dev_dbg(ctx->dev, "SUM 0x%x\n", sum_cal_itr);
|
|
++avg_loop;
|
|
} else {
|
|
dev_err(ctx->dev,
|
|
"Receiver calibration failed at %d loop\n",
|
|
avg_loop);
|
|
}
|
|
xgene_phy_reset_rxd(ctx, lane);
|
|
}
|
|
|
|
/* Update latch manual calibration with average value */
|
|
serdes_rd(ctx, lane, RXTX_REG127, &val);
|
|
val = RXTX_REG127_DO_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_do, max_loop));
|
|
val = RXTX_REG127_XO_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_xo, max_loop));
|
|
serdes_wr(ctx, lane, RXTX_REG127, val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG128, &val);
|
|
val = RXTX_REG128_EO_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_eo, max_loop));
|
|
val = RXTX_REG128_SO_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_so, max_loop));
|
|
serdes_wr(ctx, lane, RXTX_REG128, val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG129, &val);
|
|
val = RXTX_REG129_DE_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_de, max_loop));
|
|
val = RXTX_REG129_XE_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_xe, max_loop));
|
|
serdes_wr(ctx, lane, RXTX_REG129, val);
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG130, &val);
|
|
val = RXTX_REG130_EE_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_ee, max_loop));
|
|
val = RXTX_REG130_SE_LATCH_MANCAL_SET(val,
|
|
xgene_phy_get_avg(lat_se, max_loop));
|
|
serdes_wr(ctx, lane, RXTX_REG130, val);
|
|
|
|
/* Update SUMMER calibration with average value */
|
|
serdes_rd(ctx, lane, RXTX_REG14, &val);
|
|
val = RXTX_REG14_CLTE_LATCAL_MAN_PROG_SET(val,
|
|
xgene_phy_get_avg(sum_cal, max_loop));
|
|
serdes_wr(ctx, lane, RXTX_REG14, val);
|
|
|
|
dev_dbg(ctx->dev, "Average Value:\n");
|
|
dev_dbg(ctx->dev, "DO 0x%x XO 0x%x EO 0x%x SO 0x%x\n",
|
|
xgene_phy_get_avg(lat_do, max_loop),
|
|
xgene_phy_get_avg(lat_xo, max_loop),
|
|
xgene_phy_get_avg(lat_eo, max_loop),
|
|
xgene_phy_get_avg(lat_so, max_loop));
|
|
dev_dbg(ctx->dev, "DE 0x%x XE 0x%x EE 0x%x SE 0x%x\n",
|
|
xgene_phy_get_avg(lat_de, max_loop),
|
|
xgene_phy_get_avg(lat_xe, max_loop),
|
|
xgene_phy_get_avg(lat_ee, max_loop),
|
|
xgene_phy_get_avg(lat_se, max_loop));
|
|
dev_dbg(ctx->dev, "SUM 0x%x\n",
|
|
xgene_phy_get_avg(sum_cal, max_loop));
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG14, &val);
|
|
val = RXTX_REG14_CTLE_LATCAL_MAN_ENA_SET(val, 0x1);
|
|
serdes_wr(ctx, lane, RXTX_REG14, val);
|
|
dev_dbg(ctx->dev, "Enable Manual Summer calibration\n");
|
|
|
|
serdes_rd(ctx, lane, RXTX_REG127, &val);
|
|
val = RXTX_REG127_LATCH_MAN_CAL_ENA_SET(val, 0x1);
|
|
dev_dbg(ctx->dev, "Enable Manual Latch calibration\n");
|
|
serdes_wr(ctx, lane, RXTX_REG127, val);
|
|
|
|
/* Disable RX Hi-Z termination */
|
|
serdes_rd(ctx, lane, RXTX_REG12, &val);
|
|
val = RXTX_REG12_RX_DET_TERM_ENABLE_SET(val, 0);
|
|
serdes_wr(ctx, lane, RXTX_REG12, val);
|
|
/* Turn on DFE */
|
|
serdes_wr(ctx, lane, RXTX_REG28, 0x0007);
|
|
/* Set DFE preset */
|
|
serdes_wr(ctx, lane, RXTX_REG31, 0x7e00);
|
|
}
|
|
|
|
static int xgene_phy_hw_init(struct phy *phy)
|
|
{
|
|
struct xgene_phy_ctx *ctx = phy_get_drvdata(phy);
|
|
int rc;
|
|
int i;
|
|
|
|
rc = xgene_phy_hw_initialize(ctx, CLK_EXT_DIFF, SSC_DISABLE);
|
|
if (rc) {
|
|
dev_err(ctx->dev, "PHY initialize failed %d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
/* Setup clock properly after PHY configuration */
|
|
if (!IS_ERR(ctx->clk)) {
|
|
/* HW requires an toggle of the clock */
|
|
clk_prepare_enable(ctx->clk);
|
|
clk_disable_unprepare(ctx->clk);
|
|
clk_prepare_enable(ctx->clk);
|
|
}
|
|
|
|
/* Compute average value */
|
|
for (i = 0; i < MAX_LANE; i++)
|
|
xgene_phy_gen_avg_val(ctx, i);
|
|
|
|
dev_dbg(ctx->dev, "PHY initialized\n");
|
|
return 0;
|
|
}
|
|
|
|
static const struct phy_ops xgene_phy_ops = {
|
|
.init = xgene_phy_hw_init,
|
|
.owner = THIS_MODULE,
|
|
};
|
|
|
|
static struct phy *xgene_phy_xlate(struct device *dev,
|
|
struct of_phandle_args *args)
|
|
{
|
|
struct xgene_phy_ctx *ctx = dev_get_drvdata(dev);
|
|
|
|
if (args->args_count <= 0)
|
|
return ERR_PTR(-EINVAL);
|
|
if (args->args[0] < MODE_SATA || args->args[0] >= MODE_MAX)
|
|
return ERR_PTR(-EINVAL);
|
|
|
|
ctx->mode = args->args[0];
|
|
return ctx->phy;
|
|
}
|
|
|
|
static void xgene_phy_get_param(struct platform_device *pdev,
|
|
const char *name, u32 *buffer,
|
|
int count, u32 *default_val,
|
|
u32 conv_factor)
|
|
{
|
|
int i;
|
|
|
|
if (!of_property_read_u32_array(pdev->dev.of_node, name, buffer,
|
|
count)) {
|
|
for (i = 0; i < count; i++)
|
|
buffer[i] /= conv_factor;
|
|
return;
|
|
}
|
|
/* Does not exist, load default */
|
|
for (i = 0; i < count; i++)
|
|
buffer[i] = default_val[i % 3];
|
|
}
|
|
|
|
static int xgene_phy_probe(struct platform_device *pdev)
|
|
{
|
|
struct phy_provider *phy_provider;
|
|
struct xgene_phy_ctx *ctx;
|
|
struct resource *res;
|
|
u32 default_spd[] = DEFAULT_SATA_SPD_SEL;
|
|
u32 default_txboost_gain[] = DEFAULT_SATA_TXBOOST_GAIN;
|
|
u32 default_txeye_direction[] = DEFAULT_SATA_TXEYEDIRECTION;
|
|
u32 default_txeye_tuning[] = DEFAULT_SATA_TXEYETUNING;
|
|
u32 default_txamp[] = DEFAULT_SATA_TXAMP;
|
|
u32 default_txcn1[] = DEFAULT_SATA_TXCN1;
|
|
u32 default_txcn2[] = DEFAULT_SATA_TXCN2;
|
|
u32 default_txcp1[] = DEFAULT_SATA_TXCP1;
|
|
int i;
|
|
|
|
ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
|
|
if (!ctx)
|
|
return -ENOMEM;
|
|
|
|
ctx->dev = &pdev->dev;
|
|
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
ctx->sds_base = devm_ioremap_resource(&pdev->dev, res);
|
|
if (IS_ERR(ctx->sds_base))
|
|
return PTR_ERR(ctx->sds_base);
|
|
|
|
/* Retrieve optional clock */
|
|
ctx->clk = clk_get(&pdev->dev, NULL);
|
|
|
|
/* Load override paramaters */
|
|
xgene_phy_get_param(pdev, "apm,tx-eye-tuning",
|
|
ctx->sata_param.txeyetuning, 6, default_txeye_tuning, 1);
|
|
xgene_phy_get_param(pdev, "apm,tx-eye-direction",
|
|
ctx->sata_param.txeyedirection, 6, default_txeye_direction, 1);
|
|
xgene_phy_get_param(pdev, "apm,tx-boost-gain",
|
|
ctx->sata_param.txboostgain, 6, default_txboost_gain, 1);
|
|
xgene_phy_get_param(pdev, "apm,tx-amplitude",
|
|
ctx->sata_param.txamplitude, 6, default_txamp, 13300);
|
|
xgene_phy_get_param(pdev, "apm,tx-pre-cursor1",
|
|
ctx->sata_param.txprecursor_cn1, 6, default_txcn1, 18200);
|
|
xgene_phy_get_param(pdev, "apm,tx-pre-cursor2",
|
|
ctx->sata_param.txprecursor_cn2, 6, default_txcn2, 18200);
|
|
xgene_phy_get_param(pdev, "apm,tx-post-cursor",
|
|
ctx->sata_param.txpostcursor_cp1, 6, default_txcp1, 18200);
|
|
xgene_phy_get_param(pdev, "apm,tx-speed",
|
|
ctx->sata_param.txspeed, 3, default_spd, 1);
|
|
for (i = 0; i < MAX_LANE; i++)
|
|
ctx->sata_param.speed[i] = 2; /* Default to Gen3 */
|
|
|
|
platform_set_drvdata(pdev, ctx);
|
|
|
|
ctx->phy = devm_phy_create(ctx->dev, NULL, &xgene_phy_ops);
|
|
if (IS_ERR(ctx->phy)) {
|
|
dev_dbg(&pdev->dev, "Failed to create PHY\n");
|
|
return PTR_ERR(ctx->phy);
|
|
}
|
|
phy_set_drvdata(ctx->phy, ctx);
|
|
|
|
phy_provider = devm_of_phy_provider_register(ctx->dev, xgene_phy_xlate);
|
|
return PTR_ERR_OR_ZERO(phy_provider);
|
|
}
|
|
|
|
static const struct of_device_id xgene_phy_of_match[] = {
|
|
{.compatible = "apm,xgene-phy",},
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, xgene_phy_of_match);
|
|
|
|
static struct platform_driver xgene_phy_driver = {
|
|
.probe = xgene_phy_probe,
|
|
.driver = {
|
|
.name = "xgene-phy",
|
|
.of_match_table = xgene_phy_of_match,
|
|
},
|
|
};
|
|
module_platform_driver(xgene_phy_driver);
|
|
|
|
MODULE_DESCRIPTION("APM X-Gene Multi-Purpose PHY driver");
|
|
MODULE_AUTHOR("Loc Ho <lho@apm.com>");
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_VERSION("0.1");
|