WSL2-Linux-Kernel/include/linux/regulator
Mark Brown c1f615e4f4
Merge series "Fix regulators coupling for Exynos5800" from Marek Szyprowski <m.szyprowski@samsung.com>:
Hi!

This patchset is another attempt to fix the regulator coupling on
Exynos5800/5422 SoCs. Here are links to the previous attempts:

https://lore.kernel.org/linux-samsung-soc/20191008101709.qVNy8eijBi0LynOteWFMnTg4GUwKG599n6OyYoX1Abs@z/
https://lore.kernel.org/lkml/20191017102758.8104-1-m.szyprowski@samsung.com/
https://lore.kernel.org/linux-pm/cover.1589528491.git.viresh.kumar@linaro.org/
https://lore.kernel.org/linux-pm/20200528131130.17984-1-m.szyprowski@samsung.com/

The problem is with "vdd_int" regulator coupled with "vdd_arm" on Odroid
XU3/XU4 boards family. "vdd_arm" is handled by CPUfreq. "vdd_int" is
handled by devfreq. CPUfreq initialized quite early during boot and it
starts changing OPPs and "vdd_arm" value. Sometimes CPU activity during
boot goes down and some low-frequency OPPs are selected, what in turn
causes lowering "vdd_arm". This happens before devfreq applies its
requirements on "vdd_int". Regulator balancing code reduces "vdd_arm"
voltage value, what in turn causes lowering "vdd_int" value to the lowest
possible value. This is much below the operation point of the wcore bus,
which still runs at the highest frequency.

The issue was hard to notice because in the most cases the board managed
to boot properly, even when the regulator was set to lowest value allowed
by the regulator constraints. However, it caused some random issues,
which can be observed as "Unhandled prefetch abort" or low USB stability.

Adding more and more special cases to the generic code has been rejected,
so the only way to ensure the desired behavior on Exynos5800-based SoCs
is to make a custom regulator coupler driver.

Best regards,
Marek Szyprowski

Patch summary:

Marek Szyprowski (2):
  regulator: extract voltage balancing code to separate function
  soc: samsung: Add simple voltage coupler for Exynos5800

 arch/arm/mach-exynos/Kconfig                  |  1 +
 drivers/regulator/core.c                      | 49 ++++++++-------
 drivers/soc/samsung/Kconfig                   |  3 +
 drivers/soc/samsung/Makefile                  |  1 +
 .../soc/samsung/exynos-regulator-coupler.c    | 59 +++++++++++++++++++
 include/linux/regulator/coupler.h             |  8 +++
 6 files changed, 101 insertions(+), 20 deletions(-)
 create mode 100644 drivers/soc/samsung/exynos-regulator-coupler.c

--
2.17.1

base-commit: 8f3d9f3542
2020-05-29 14:36:03 +01:00
..
ab8500.h regulator: ab8500: Remove SYSCLKREQ from enum ab8505_regulator_id 2019-11-07 13:10:08 +00:00
act8865.h
arizona-ldo1.h
arizona-micsupp.h
consumer.h regulator fix for "regulator: core: Add regulator_is_equal() helper" 2020-01-15 14:10:45 +00:00
coupler.h regulator: extract voltage balancing code to the separate function 2020-05-29 14:36:00 +01:00
da9211.h
db8500-prcmu.h
driver.h regulator: use linear_ranges helper 2020-05-08 18:18:13 +01:00
fan53555.h
fixed.h regulator: fixed: add off-on-delay 2019-10-29 12:32:12 +00:00
gpio-regulator.h
lp872x.h
lp3971.h
lp3972.h
machine.h Merge remote-tracking branch 'regulator/topic/coupled' into regulator-next 2019-07-04 17:34:34 +01:00
max1586.h
max8649.h
max8660.h
max8952.h
max8973-regulator.h
mt6311.h
mt6323-regulator.h
mt6358-regulator.h regulator: mt6358: Add support for MT6358 regulator 2019-08-28 11:51:27 +01:00
mt6380-regulator.h
mt6397-regulator.h
of_regulator.h
pfuze100.h
tps6507x.h
tps51632-regulator.h
tps62360.h
userspace-consumer.h