89 строки
3.1 KiB
Plaintext
89 строки
3.1 KiB
Plaintext
* Freescale i.MX7 Dual IOMUX Controller
|
|
|
|
iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar
|
|
as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low
|
|
power state retention capabilities on gpios that are part of iomuxc-lpsr
|
|
(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for
|
|
mux and pad control settings, it shares the input select register from main
|
|
iomuxc controller for daisy chain settings, the fsl,input-sel property extends
|
|
fsl,imx-pinctrl driver to support iomuxc-lpsr controller.
|
|
|
|
iomuxc_lpsr: iomuxc-lpsr@302c0000 {
|
|
compatible = "fsl,imx7d-iomuxc-lpsr";
|
|
reg = <0x302c0000 0x10000>;
|
|
fsl,input-sel = <&iomuxc>;
|
|
};
|
|
|
|
iomuxc: iomuxc@30330000 {
|
|
compatible = "fsl,imx7d-iomuxc";
|
|
reg = <0x30330000 0x10000>;
|
|
};
|
|
|
|
Peripherals using pads from iomuxc-lpsr support low state retention power
|
|
state, under LPSR mode GPIO's state of pads are retain.
|
|
|
|
Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
|
|
and usage.
|
|
|
|
Required properties:
|
|
- compatible: "fsl,imx7d-iomuxc" for main IOMUXC controller, or
|
|
"fsl,imx7d-iomuxc-lpsr" for Low Power State Retention IOMUXC controller.
|
|
- fsl,pins: each entry consists of 6 integers and represents the mux and config
|
|
setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val
|
|
input_val> are specified using a PIN_FUNC_ID macro, which can be found in
|
|
imx7d-pinfunc.h under device tree source folder. The last integer CONFIG is
|
|
the pad setting value like pull-up on this pin. Please refer to i.MX7 Dual
|
|
Reference Manual for detailed CONFIG settings.
|
|
- fsl,input-sel: required property for iomuxc-lpsr controller, this property is
|
|
a phandle for main iomuxc controller which shares the input select register for
|
|
daisy chain settings.
|
|
|
|
CONFIG bits definition:
|
|
PAD_CTL_PUS_100K_DOWN (0 << 5)
|
|
PAD_CTL_PUS_5K_UP (1 << 5)
|
|
PAD_CTL_PUS_47K_UP (2 << 5)
|
|
PAD_CTL_PUS_100K_UP (3 << 5)
|
|
PAD_CTL_PUE (1 << 4)
|
|
PAD_CTL_HYS (1 << 3)
|
|
PAD_CTL_SRE_SLOW (1 << 2)
|
|
PAD_CTL_SRE_FAST (0 << 2)
|
|
PAD_CTL_DSE_X1 (0 << 0)
|
|
PAD_CTL_DSE_X2 (1 << 0)
|
|
PAD_CTL_DSE_X3 (2 << 0)
|
|
PAD_CTL_DSE_X4 (3 << 0)
|
|
|
|
Examples:
|
|
While iomuxc-lpsr is intended to be used by dedicated peripherals to take
|
|
advantages of LPSR power mode, is also possible that an IP to use pads from
|
|
any of the iomux controllers. For example the I2C1 IP can use SCL pad from
|
|
iomuxc-lpsr controller and SDA pad from iomuxc controller as:
|
|
|
|
i2c1: i2c@30a20000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>;
|
|
status = "okay";
|
|
};
|
|
|
|
iomuxc-lpsr@302c0000 {
|
|
compatible = "fsl,imx7d-iomuxc-lpsr";
|
|
reg = <0x302c0000 0x10000>;
|
|
fsl,input-sel = <&iomuxc>;
|
|
|
|
pinctrl_i2c1_1: i2c1grp-1 {
|
|
fsl,pins = <
|
|
MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f
|
|
>;
|
|
};
|
|
};
|
|
|
|
iomuxc@30330000 {
|
|
compatible = "fsl,imx7d-iomuxc";
|
|
reg = <0x30330000 0x10000>;
|
|
|
|
pinctrl_i2c1_2: i2c1grp-2 {
|
|
fsl,pins = <
|
|
MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f
|
|
>;
|
|
};
|
|
};
|