WSL2-Linux-Kernel/sound/oss/dmasound/awacs_defs.h

252 строки
9.3 KiB
C

/*********************************************************/
/* This file was written by someone, somewhere, sometime */
/* And is released into the Public Domain */
/*********************************************************/
#ifndef _AWACS_DEFS_H_
#define _AWACS_DEFS_H_
/*******************************/
/* AWACs Audio Register Layout */
/*******************************/
struct awacs_regs {
unsigned control; /* Audio control register */
unsigned pad0[3];
unsigned codec_ctrl; /* Codec control register */
unsigned pad1[3];
unsigned codec_stat; /* Codec status register */
unsigned pad2[3];
unsigned clip_count; /* Clipping count register */
unsigned pad3[3];
unsigned byteswap; /* Data is little-endian if 1 */
};
/*******************/
/* Audio Bit Masks */
/*******************/
/* Audio Control Reg Bit Masks */
/* ----- ------- --- --- ----- */
#define MASK_ISFSEL (0xf) /* Input SubFrame Select */
#define MASK_OSFSEL (0xf << 4) /* Output SubFrame Select */
#define MASK_RATE (0x7 << 8) /* Sound Rate */
#define MASK_CNTLERR (0x1 << 11) /* Error */
#define MASK_PORTCHG (0x1 << 12) /* Port Change */
#define MASK_IEE (0x1 << 13) /* Enable Interrupt on Error */
#define MASK_IEPC (0x1 << 14) /* Enable Interrupt on Port Change */
#define MASK_SSFSEL (0x3 << 15) /* Status SubFrame Select */
/* Audio Codec Control Reg Bit Masks */
/* ----- ----- ------- --- --- ----- */
#define MASK_NEWECMD (0x1 << 24) /* Lock: don't write to reg when 1 */
#define MASK_EMODESEL (0x3 << 22) /* Send info out on which frame? */
#define MASK_EXMODEADDR (0x3ff << 12) /* Extended Mode Address -- 10 bits */
#define MASK_EXMODEDATA (0xfff) /* Extended Mode Data -- 12 bits */
/* Audio Codec Control Address Values / Masks */
/* ----- ----- ------- ------- ------ - ----- */
#define MASK_ADDR0 (0x0 << 12) /* Expanded Data Mode Address 0 */
#define MASK_ADDR_MUX MASK_ADDR0 /* Mux Control */
#define MASK_ADDR_GAIN MASK_ADDR0
#define MASK_ADDR1 (0x1 << 12) /* Expanded Data Mode Address 1 */
#define MASK_ADDR_MUTE MASK_ADDR1
#define MASK_ADDR_RATE MASK_ADDR1
#define MASK_ADDR2 (0x2 << 12) /* Expanded Data Mode Address 2 */
#define MASK_ADDR_VOLA MASK_ADDR2 /* Volume Control A -- Headphones */
#define MASK_ADDR_VOLHD MASK_ADDR2
#define MASK_ADDR4 (0x4 << 12) /* Expanded Data Mode Address 4 */
#define MASK_ADDR_VOLC MASK_ADDR4 /* Volume Control C -- Speaker */
#define MASK_ADDR_VOLSPK MASK_ADDR4
/* additional registers of screamer */
#define MASK_ADDR5 (0x5 << 12) /* Expanded Data Mode Address 5 */
#define MASK_ADDR6 (0x6 << 12) /* Expanded Data Mode Address 6 */
#define MASK_ADDR7 (0x7 << 12) /* Expanded Data Mode Address 7 */
/* Address 0 Bit Masks & Macros */
/* ------- - --- ----- - ------ */
#define MASK_GAINRIGHT (0xf) /* Gain Right Mask */
#define MASK_GAINLEFT (0xf << 4) /* Gain Left Mask */
#define MASK_GAINLINE (0x1 << 8) /* Disable Mic preamp */
#define MASK_GAINMIC (0x0 << 8) /* Enable Mic preamp */
#define MASK_MUX_CD (0x1 << 9) /* Select CD in MUX */
#define MASK_MUX_MIC (0x1 << 10) /* Select Mic in MUX */
#define MASK_MUX_AUDIN (0x1 << 11) /* Select Audio In in MUX */
#define MASK_MUX_LINE MASK_MUX_AUDIN
#define GAINRIGHT(x) ((x) & MASK_GAINRIGHT)
#define GAINLEFT(x) (((x) << 4) & MASK_GAINLEFT)
#define DEF_CD_GAIN 0x00bb
#define DEF_MIC_GAIN 0x00cc
/* Address 1 Bit Masks */
/* ------- - --- ----- */
#define MASK_ADDR1RES1 (0x3) /* Reserved */
#define MASK_RECALIBRATE (0x1 << 2) /* Recalibrate */
#define MASK_SAMPLERATE (0x7 << 3) /* Sample Rate: */
#define MASK_LOOPTHRU (0x1 << 6) /* Loopthrough Enable */
#define MASK_CMUTE (0x1 << 7) /* Output C (Speaker) Mute when 1 */
#define MASK_SPKMUTE MASK_CMUTE
#define MASK_ADDR1RES2 (0x1 << 8) /* Reserved */
#define MASK_AMUTE (0x1 << 9) /* Output A (Headphone) Mute when 1 */
#define MASK_HDMUTE MASK_AMUTE
#define MASK_PAROUT0 (0x1 << 10) /* Parallel Output 0 */
#define MASK_PAROUT1 (0x2 << 10) /* Parallel Output 1 */
#define MASK_MIC_BOOST (0x4) /* screamer mic boost */
#define SAMPLERATE_48000 (0x0 << 3) /* 48 or 44.1 kHz */
#define SAMPLERATE_32000 (0x1 << 3) /* 32 or 29.4 kHz */
#define SAMPLERATE_24000 (0x2 << 3) /* 24 or 22.05 kHz */
#define SAMPLERATE_19200 (0x3 << 3) /* 19.2 or 17.64 kHz */
#define SAMPLERATE_16000 (0x4 << 3) /* 16 or 14.7 kHz */
#define SAMPLERATE_12000 (0x5 << 3) /* 12 or 11.025 kHz */
#define SAMPLERATE_9600 (0x6 << 3) /* 9.6 or 8.82 kHz */
#define SAMPLERATE_8000 (0x7 << 3) /* 8 or 7.35 kHz */
/* Address 2 & 4 Bit Masks & Macros */
/* ------- - - - --- ----- - ------ */
#define MASK_OUTVOLRIGHT (0xf) /* Output Right Volume */
#define MASK_ADDR2RES1 (0x2 << 4) /* Reserved */
#define MASK_ADDR4RES1 MASK_ADDR2RES1
#define MASK_OUTVOLLEFT (0xf << 6) /* Output Left Volume */
#define MASK_ADDR2RES2 (0x2 << 10) /* Reserved */
#define MASK_ADDR4RES2 MASK_ADDR2RES2
#define VOLRIGHT(x) (((~(x)) & MASK_OUTVOLRIGHT))
#define VOLLEFT(x) (((~(x)) << 6) & MASK_OUTVOLLEFT)
/* Audio Codec Status Reg Bit Masks */
/* ----- ----- ------ --- --- ----- */
#define MASK_EXTEND (0x1 << 23) /* Extend */
#define MASK_VALID (0x1 << 22) /* Valid Data? */
#define MASK_OFLEFT (0x1 << 21) /* Overflow Left */
#define MASK_OFRIGHT (0x1 << 20) /* Overflow Right */
#define MASK_ERRCODE (0xf << 16) /* Error Code */
#define MASK_REVISION (0xf << 12) /* Revision Number */
#define MASK_MFGID (0xf << 8) /* Mfg. ID */
#define MASK_CODSTATRES (0xf << 4) /* bits 4 - 7 reserved */
#define MASK_INPPORT (0xf) /* Input Port */
#define MASK_HDPCONN 8 /* headphone plugged in */
/* Clipping Count Reg Bit Masks */
/* -------- ----- --- --- ----- */
#define MASK_CLIPLEFT (0xff << 7) /* Clipping Count, Left Channel */
#define MASK_CLIPRIGHT (0xff) /* Clipping Count, Right Channel */
/* DBDMA ChannelStatus Bit Masks */
/* ----- ------------- --- ----- */
#define MASK_CSERR (0x1 << 7) /* Error */
#define MASK_EOI (0x1 << 6) /* End of Input -- only for Input Channel */
#define MASK_CSUNUSED (0x1f << 1) /* bits 1-5 not used */
#define MASK_WAIT (0x1) /* Wait */
/* Various Rates */
/* ------- ----- */
#define RATE_48000 (0x0 << 8) /* 48 kHz */
#define RATE_44100 (0x0 << 8) /* 44.1 kHz */
#define RATE_32000 (0x1 << 8) /* 32 kHz */
#define RATE_29400 (0x1 << 8) /* 29.4 kHz */
#define RATE_24000 (0x2 << 8) /* 24 kHz */
#define RATE_22050 (0x2 << 8) /* 22.05 kHz */
#define RATE_19200 (0x3 << 8) /* 19.2 kHz */
#define RATE_17640 (0x3 << 8) /* 17.64 kHz */
#define RATE_16000 (0x4 << 8) /* 16 kHz */
#define RATE_14700 (0x4 << 8) /* 14.7 kHz */
#define RATE_12000 (0x5 << 8) /* 12 kHz */
#define RATE_11025 (0x5 << 8) /* 11.025 kHz */
#define RATE_9600 (0x6 << 8) /* 9.6 kHz */
#define RATE_8820 (0x6 << 8) /* 8.82 kHz */
#define RATE_8000 (0x7 << 8) /* 8 kHz */
#define RATE_7350 (0x7 << 8) /* 7.35 kHz */
#define RATE_LOW 1 /* HIGH = 48kHz, etc; LOW = 44.1kHz, etc. */
/*******************/
/* Burgundy values */
/*******************/
#define MASK_ADDR_BURGUNDY_INPSEL21 (0x11 << 12)
#define MASK_ADDR_BURGUNDY_INPSEL3 (0x12 << 12)
#define MASK_ADDR_BURGUNDY_GAINCH1 (0x13 << 12)
#define MASK_ADDR_BURGUNDY_GAINCH2 (0x14 << 12)
#define MASK_ADDR_BURGUNDY_GAINCH3 (0x15 << 12)
#define MASK_ADDR_BURGUNDY_GAINCH4 (0x16 << 12)
#define MASK_ADDR_BURGUNDY_VOLCH1 (0x20 << 12)
#define MASK_ADDR_BURGUNDY_VOLCH2 (0x21 << 12)
#define MASK_ADDR_BURGUNDY_VOLCH3 (0x22 << 12)
#define MASK_ADDR_BURGUNDY_VOLCH4 (0x23 << 12)
#define MASK_ADDR_BURGUNDY_OUTPUTSELECTS (0x2B << 12)
#define MASK_ADDR_BURGUNDY_OUTPUTENABLES (0x2F << 12)
#define MASK_ADDR_BURGUNDY_MASTER_VOLUME (0x30 << 12)
#define MASK_ADDR_BURGUNDY_MORE_OUTPUTENABLES (0x60 << 12)
#define MASK_ADDR_BURGUNDY_ATTENSPEAKER (0x62 << 12)
#define MASK_ADDR_BURGUNDY_ATTENLINEOUT (0x63 << 12)
#define MASK_ADDR_BURGUNDY_ATTENHP (0x64 << 12)
#define MASK_ADDR_BURGUNDY_VOLCD (MASK_ADDR_BURGUNDY_VOLCH1)
#define MASK_ADDR_BURGUNDY_VOLLINE (MASK_ADDR_BURGUNDY_VOLCH2)
#define MASK_ADDR_BURGUNDY_VOLMIC (MASK_ADDR_BURGUNDY_VOLCH3)
#define MASK_ADDR_BURGUNDY_VOLMODEM (MASK_ADDR_BURGUNDY_VOLCH4)
#define MASK_ADDR_BURGUNDY_GAINCD (MASK_ADDR_BURGUNDY_GAINCH1)
#define MASK_ADDR_BURGUNDY_GAINLINE (MASK_ADDR_BURGUNDY_GAINCH2)
#define MASK_ADDR_BURGUNDY_GAINMIC (MASK_ADDR_BURGUNDY_GAINCH3)
#define MASK_ADDR_BURGUNDY_GAINMODEM (MASK_ADDR_BURGUNDY_VOLCH4)
/* These are all default values for the burgundy */
#define DEF_BURGUNDY_INPSEL21 (0xAA)
#define DEF_BURGUNDY_INPSEL3 (0x0A)
#define DEF_BURGUNDY_GAINCD (0x33)
#define DEF_BURGUNDY_GAINLINE (0x44)
#define DEF_BURGUNDY_GAINMIC (0x44)
#define DEF_BURGUNDY_GAINMODEM (0x06)
/* Remember: lowest volume here is 0x9b */
#define DEF_BURGUNDY_VOLCD (0xCCCCCCCC)
#define DEF_BURGUNDY_VOLLINE (0x00000000)
#define DEF_BURGUNDY_VOLMIC (0x00000000)
#define DEF_BURGUNDY_VOLMODEM (0xCCCCCCCC)
#define DEF_BURGUNDY_OUTPUTSELECTS (0x010f010f)
#define DEF_BURGUNDY_OUTPUTENABLES (0x0A)
#define DEF_BURGUNDY_MASTER_VOLUME (0xFFFFFFFF)
#define DEF_BURGUNDY_MORE_OUTPUTENABLES (0x7E)
#define DEF_BURGUNDY_ATTENSPEAKER (0x44)
#define DEF_BURGUNDY_ATTENLINEOUT (0xCC)
#define DEF_BURGUNDY_ATTENHP (0xCC)
/*********************/
/* i2s layout values */
/*********************/
#define I2S_REG_INT_CTL 0x00
#define I2S_REG_SERIAL_FORMAT 0x10
#define I2S_REG_CODEC_MSG_OUT 0x20
#define I2S_REG_CODEC_MSG_IN 0x30
#define I2S_REG_FRAME_COUNT 0x40
#define I2S_REG_FRAME_MATCH 0x50
#define I2S_REG_DATAWORD_SIZES 0x60
#define I2S_REG_PEAKLEVEL_SEL 0x70
#define I2S_REG_PEAKLEVEL_IN0 0x80
#define I2S_REG_PEAKLEVEL_IN1 0x90
#endif /* _AWACS_DEFS_H_ */