254 строки
6.7 KiB
C
254 строки
6.7 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* pata_radisys.c - Intel PATA/SATA controllers
|
|
*
|
|
* (C) 2006 Red Hat <alan@lxorguk.ukuu.org.uk>
|
|
*
|
|
* Some parts based on ata_piix.c by Jeff Garzik and others.
|
|
*
|
|
* A PIIX relative, this device has a single ATA channel and no
|
|
* slave timings, SITRE or PPE. In that sense it is a close relative
|
|
* of the original PIIX. It does however support UDMA 33/66 per channel
|
|
* although no other modes/timings. Also lacking is 32bit I/O on the ATA
|
|
* port.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/device.h>
|
|
#include <scsi/scsi_host.h>
|
|
#include <linux/libata.h>
|
|
#include <linux/ata.h>
|
|
|
|
#define DRV_NAME "pata_radisys"
|
|
#define DRV_VERSION "0.4.4"
|
|
|
|
/**
|
|
* radisys_set_piomode - Initialize host controller PATA PIO timings
|
|
* @ap: ATA port
|
|
* @adev: Device whose timings we are configuring
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
unsigned int pio = adev->pio_mode - XFER_PIO_0;
|
|
struct pci_dev *dev = to_pci_dev(ap->host->dev);
|
|
u16 idetm_data;
|
|
int control = 0;
|
|
|
|
/*
|
|
* See Intel Document 298600-004 for the timing programing rules
|
|
* for PIIX/ICH. Note that the early PIIX does not have the slave
|
|
* timing port at 0x44. The Radisys is a relative of the PIIX
|
|
* but not the same so be careful.
|
|
*/
|
|
|
|
static const /* ISP RTC */
|
|
u8 timings[][2] = { { 0, 0 }, /* Check me */
|
|
{ 0, 0 },
|
|
{ 1, 1 },
|
|
{ 2, 2 },
|
|
{ 3, 3 }, };
|
|
|
|
if (pio > 0)
|
|
control |= 1; /* TIME1 enable */
|
|
if (ata_pio_need_iordy(adev))
|
|
control |= 2; /* IE IORDY */
|
|
|
|
pci_read_config_word(dev, 0x40, &idetm_data);
|
|
|
|
/* Enable IE and TIME as appropriate. Clear the other
|
|
drive timing bits */
|
|
idetm_data &= 0xCCCC;
|
|
idetm_data |= (control << (4 * adev->devno));
|
|
idetm_data |= (timings[pio][0] << 12) |
|
|
(timings[pio][1] << 8);
|
|
pci_write_config_word(dev, 0x40, idetm_data);
|
|
|
|
/* Track which port is configured */
|
|
ap->private_data = adev;
|
|
}
|
|
|
|
/**
|
|
* radisys_set_dmamode - Initialize host controller PATA DMA timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device to program
|
|
*
|
|
* Set MWDMA mode for device, in host controller PCI config space.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(ap->host->dev);
|
|
u16 idetm_data;
|
|
u8 udma_enable;
|
|
|
|
static const /* ISP RTC */
|
|
u8 timings[][2] = { { 0, 0 },
|
|
{ 0, 0 },
|
|
{ 1, 1 },
|
|
{ 2, 2 },
|
|
{ 3, 3 }, };
|
|
|
|
/*
|
|
* MWDMA is driven by the PIO timings. We must also enable
|
|
* IORDY unconditionally.
|
|
*/
|
|
|
|
pci_read_config_word(dev, 0x40, &idetm_data);
|
|
pci_read_config_byte(dev, 0x48, &udma_enable);
|
|
|
|
if (adev->dma_mode < XFER_UDMA_0) {
|
|
unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
|
|
const unsigned int needed_pio[3] = {
|
|
XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
|
|
};
|
|
int pio = needed_pio[mwdma] - XFER_PIO_0;
|
|
int control = 3; /* IORDY|TIME0 */
|
|
|
|
/* If the drive MWDMA is faster than it can do PIO then
|
|
we must force PIO0 for PIO cycles. */
|
|
|
|
if (adev->pio_mode < needed_pio[mwdma])
|
|
control = 1;
|
|
|
|
/* Mask out the relevant control and timing bits we will load. Also
|
|
clear the other drive TIME register as a precaution */
|
|
|
|
idetm_data &= 0xCCCC;
|
|
idetm_data |= control << (4 * adev->devno);
|
|
idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
|
|
|
|
udma_enable &= ~(1 << adev->devno);
|
|
} else {
|
|
u8 udma_mode;
|
|
|
|
/* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */
|
|
|
|
pci_read_config_byte(dev, 0x4A, &udma_mode);
|
|
|
|
if (adev->xfer_mode == XFER_UDMA_2)
|
|
udma_mode &= ~(2 << (adev->devno * 4));
|
|
else /* UDMA 4 */
|
|
udma_mode |= (2 << (adev->devno * 4));
|
|
|
|
pci_write_config_byte(dev, 0x4A, udma_mode);
|
|
|
|
udma_enable |= (1 << adev->devno);
|
|
}
|
|
pci_write_config_word(dev, 0x40, idetm_data);
|
|
pci_write_config_byte(dev, 0x48, udma_enable);
|
|
|
|
/* Track which port is configured */
|
|
ap->private_data = adev;
|
|
}
|
|
|
|
/**
|
|
* radisys_qc_issue - command issue
|
|
* @qc: command pending
|
|
*
|
|
* Called when the libata layer is about to issue a command. We wrap
|
|
* this interface so that we can load the correct ATA timings if
|
|
* necessary. Our logic also clears TIME0/TIME1 for the other device so
|
|
* that, even if we get this wrong, cycles to the other device will
|
|
* be made PIO0.
|
|
*/
|
|
|
|
static unsigned int radisys_qc_issue(struct ata_queued_cmd *qc)
|
|
{
|
|
struct ata_port *ap = qc->ap;
|
|
struct ata_device *adev = qc->dev;
|
|
|
|
if (adev != ap->private_data) {
|
|
/* UDMA timing is not shared */
|
|
if (adev->dma_mode < XFER_UDMA_0 || !ata_dma_enabled(adev)) {
|
|
if (ata_dma_enabled(adev))
|
|
radisys_set_dmamode(ap, adev);
|
|
else if (adev->pio_mode)
|
|
radisys_set_piomode(ap, adev);
|
|
}
|
|
}
|
|
return ata_bmdma_qc_issue(qc);
|
|
}
|
|
|
|
|
|
static const struct scsi_host_template radisys_sht = {
|
|
ATA_BMDMA_SHT(DRV_NAME),
|
|
};
|
|
|
|
static struct ata_port_operations radisys_pata_ops = {
|
|
.inherits = &ata_bmdma_port_ops,
|
|
.qc_issue = radisys_qc_issue,
|
|
.cable_detect = ata_cable_unknown,
|
|
.set_piomode = radisys_set_piomode,
|
|
.set_dmamode = radisys_set_dmamode,
|
|
};
|
|
|
|
|
|
/**
|
|
* radisys_init_one - Register PIIX ATA PCI device with kernel services
|
|
* @pdev: PCI device to register
|
|
* @ent: Entry in radisys_pci_tbl matching with @pdev
|
|
*
|
|
* Called from kernel PCI layer. We probe for combined mode (sigh),
|
|
* and then hand over control to libata, for it to do the rest.
|
|
*
|
|
* LOCKING:
|
|
* Inherited from PCI layer (may sleep).
|
|
*
|
|
* RETURNS:
|
|
* Zero on success, or -ERRNO value.
|
|
*/
|
|
|
|
static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
|
|
{
|
|
static const struct ata_port_info info = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA12_ONLY,
|
|
.udma_mask = ATA_UDMA24_ONLY,
|
|
.port_ops = &radisys_pata_ops,
|
|
};
|
|
const struct ata_port_info *ppi[] = { &info, NULL };
|
|
|
|
ata_print_version_once(&pdev->dev, DRV_VERSION);
|
|
|
|
return ata_pci_bmdma_init_one(pdev, ppi, &radisys_sht, NULL, 0);
|
|
}
|
|
|
|
static const struct pci_device_id radisys_pci_tbl[] = {
|
|
{ PCI_VDEVICE(RADISYS, 0x8201), },
|
|
|
|
{ } /* terminate list */
|
|
};
|
|
|
|
static struct pci_driver radisys_pci_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = radisys_pci_tbl,
|
|
.probe = radisys_init_one,
|
|
.remove = ata_pci_remove_one,
|
|
#ifdef CONFIG_PM_SLEEP
|
|
.suspend = ata_pci_device_suspend,
|
|
.resume = ata_pci_device_resume,
|
|
#endif
|
|
};
|
|
|
|
module_pci_driver(radisys_pci_driver);
|
|
|
|
MODULE_AUTHOR("Alan Cox");
|
|
MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
|
|
MODULE_VERSION(DRV_VERSION);
|