263 строки
8.3 KiB
Plaintext
263 строки
8.3 KiB
Plaintext
One-register-per-pin type device tree based pinctrl driver
|
|
|
|
Required properties:
|
|
- compatible : "pinctrl-single" or "pinconf-single".
|
|
"pinctrl-single" means that pinconf isn't supported.
|
|
"pinconf-single" means that generic pinconf is supported.
|
|
|
|
- reg : offset and length of the register set for the mux registers
|
|
|
|
- #pinctrl-cells : number of cells in addition to the index, set to 1
|
|
or 2 for pinctrl-single,pins and set to 2 for pinctrl-single,bits
|
|
|
|
- pinctrl-single,register-width : pinmux register access width in bits
|
|
|
|
- pinctrl-single,function-mask : mask of allowed pinmux function bits
|
|
in the pinmux register
|
|
|
|
Optional properties:
|
|
- pinctrl-single,function-off : function off mode for disabled state if
|
|
available and same for all registers; if not specified, disabling of
|
|
pin functions is ignored
|
|
|
|
- pinctrl-single,bit-per-mux : boolean to indicate that one register controls
|
|
more than one pin, for which "pinctrl-single,function-mask" property specifies
|
|
position mask of pin.
|
|
|
|
- pinctrl-single,drive-strength : array of value that are used to configure
|
|
drive strength in the pinmux register. They're value of drive strength
|
|
current and drive strength mask.
|
|
|
|
/* drive strength current, mask */
|
|
pinctrl-single,power-source = <0x30 0xf0>;
|
|
|
|
- pinctrl-single,bias-pullup : array of value that are used to configure the
|
|
input bias pullup in the pinmux register.
|
|
|
|
/* input, enabled pullup bits, disabled pullup bits, mask */
|
|
pinctrl-single,bias-pullup = <0 1 0 1>;
|
|
|
|
- pinctrl-single,bias-pulldown : array of value that are used to configure the
|
|
input bias pulldown in the pinmux register.
|
|
|
|
/* input, enabled pulldown bits, disabled pulldown bits, mask */
|
|
pinctrl-single,bias-pulldown = <2 2 0 2>;
|
|
|
|
* Two bits to control input bias pullup and pulldown: User should use
|
|
pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
|
|
pullup, and the other one bit means pulldown.
|
|
* Three bits to control input bias enable, pullup and pulldown. User should
|
|
use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
|
|
enable bit should be included in pullup or pulldown bits.
|
|
* Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as
|
|
pinctrl-single,bias-disable. Because pinctrl single driver could implement
|
|
it by calling pulldown, pullup disabled.
|
|
|
|
- pinctrl-single,input-schmitt : array of value that are used to configure
|
|
input schmitt in the pinmux register. In some silicons, there're two input
|
|
schmitt value (rising-edge & falling-edge) in the pinmux register.
|
|
|
|
/* input schmitt value, mask */
|
|
pinctrl-single,input-schmitt = <0x30 0x70>;
|
|
|
|
- pinctrl-single,input-schmitt-enable : array of value that are used to
|
|
configure input schmitt enable or disable in the pinmux register.
|
|
|
|
/* input, enable bits, disable bits, mask */
|
|
pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
|
|
|
|
- pinctrl-single,low-power-mode : array of value that are used to configure
|
|
low power mode of this pin. For some silicons, the low power mode will
|
|
control the output of the pin when the pad including the pin enter low
|
|
power mode.
|
|
/* low power mode value, mask */
|
|
pinctrl-single,low-power-mode = <0x288 0x388>;
|
|
|
|
- pinctrl-single,gpio-range : list of value that are used to configure a GPIO
|
|
range. They're value of subnode phandle, pin base in pinctrl device, pin
|
|
number in this range, GPIO function value of this GPIO range.
|
|
The number of parameters is depend on #pinctrl-single,gpio-range-cells
|
|
property.
|
|
|
|
/* pin base, nr pins & gpio function */
|
|
pinctrl-single,gpio-range = <&range 0 3 0>, <&range 3 9 1>;
|
|
|
|
- interrupt-controller : standard interrupt controller binding if using
|
|
interrupts for wake-up events for example. In this case pinctrl-single
|
|
is set up as a chained interrupt controller and the wake-up interrupts
|
|
can be requested by the drivers using request_irq().
|
|
|
|
- #interrupt-cells : standard interrupt binding if using interrupts
|
|
|
|
This driver assumes that there is only one register for each pin (unless the
|
|
pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
|
|
specified in the pinctrl-bindings.txt document in this directory.
|
|
|
|
The pin configuration nodes for pinctrl-single are specified as pinctrl
|
|
register offset and values using pinctrl-single,pins. Only the bits specified
|
|
in pinctrl-single,function-mask are updated.
|
|
|
|
When #pinctrl-cells = 1, then setting a pin for a device could be done with:
|
|
|
|
pinctrl-single,pins = <0xdc 0x118>;
|
|
|
|
Where 0xdc is the offset from the pinctrl register base address for the device
|
|
pinctrl register, and 0x118 contains the desired value of the pinctrl register.
|
|
|
|
When #pinctrl-cells = 2, then setting a pin for a device could be done with:
|
|
|
|
pinctrl-single,pins = <0xdc 0x30 0x07>;
|
|
|
|
Where 0x30 is the pin configuration value and 0x07 is the pin mux mode value.
|
|
These two values are OR'd together to produce the value stored at offset 0xdc.
|
|
See the device example and static board pins example below for more information.
|
|
|
|
In case when one register changes more than one pin's mux the
|
|
pinctrl-single,bits need to be used which takes three parameters:
|
|
|
|
pinctrl-single,bits = <0xdc 0x18 0xff>;
|
|
|
|
Where 0xdc is the offset from the pinctrl register base address for the
|
|
device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
|
|
be used when applying this change to the register.
|
|
|
|
|
|
Optional sub-node: In case some pins could be configured as GPIO in the pinmux
|
|
register, those pins could be defined as a GPIO range. This sub-node is required
|
|
by pinctrl-single,gpio-range property.
|
|
|
|
Required properties in sub-node:
|
|
- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
|
|
pinctrl-single,gpio-range property.
|
|
|
|
range: gpio-range {
|
|
#pinctrl-single,gpio-range-cells = <3>;
|
|
};
|
|
|
|
|
|
Example:
|
|
|
|
/* SoC common file */
|
|
|
|
/* first controller instance for pins in core domain */
|
|
pmx_core: pinmux@4a100040 {
|
|
compatible = "pinctrl-single";
|
|
reg = <0x4a100040 0x0196>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
interrupt-controller;
|
|
pinctrl-single,register-width = <16>;
|
|
pinctrl-single,function-mask = <0xffff>;
|
|
};
|
|
|
|
/* second controller instance for pins in wkup domain */
|
|
pmx_wkup: pinmux@4a31e040 {
|
|
compatible = "pinctrl-single";
|
|
reg = <0x4a31e040 0x0038>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
interrupt-controller;
|
|
pinctrl-single,register-width = <16>;
|
|
pinctrl-single,function-mask = <0xffff>;
|
|
};
|
|
|
|
control_devconf0: pinmux@48002274 {
|
|
compatible = "pinctrl-single";
|
|
reg = <0x48002274 4>; /* Single register */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-single,bit-per-mux;
|
|
pinctrl-single,register-width = <32>;
|
|
pinctrl-single,function-mask = <0x5F>;
|
|
};
|
|
|
|
/* third controller instance for pins in gpio domain */
|
|
pmx_gpio: pinmux@d401e000 {
|
|
compatible = "pinconf-single";
|
|
reg = <0xd401e000 0x0330>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
pinctrl-single,register-width = <32>;
|
|
pinctrl-single,function-mask = <7>;
|
|
|
|
/* sparse GPIO range could be supported */
|
|
pinctrl-single,gpio-range = <&range 0 3 0>, <&range 3 9 1>,
|
|
<&range 12 1 0>, <&range 13 29 1>,
|
|
<&range 43 1 0>, <&range 44 49 1>,
|
|
<&range 94 1 1>, <&range 96 2 1>;
|
|
|
|
range: gpio-range {
|
|
#pinctrl-single,gpio-range-cells = <3>;
|
|
};
|
|
};
|
|
|
|
|
|
/* board specific .dts file */
|
|
|
|
&pmx_core {
|
|
|
|
/*
|
|
* map all board specific static pins enabled by the pinctrl driver
|
|
* itself during the boot (or just set them up in the bootloader)
|
|
*/
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&board_pins>;
|
|
|
|
board_pins: pinmux_board_pins {
|
|
pinctrl-single,pins = <
|
|
0x6c 0xf
|
|
0x6e 0xf
|
|
0x70 0xf
|
|
0x72 0xf
|
|
>;
|
|
};
|
|
|
|
uart0_pins: pinmux_uart0_pins {
|
|
pinctrl-single,pins = <
|
|
0x208 0 /* UART0_RXD (IOCFG138) */
|
|
0x20c 0 /* UART0_TXD (IOCFG139) */
|
|
>;
|
|
pinctrl-single,bias-pulldown = <0 2 2>;
|
|
pinctrl-single,bias-pullup = <0 1 1>;
|
|
};
|
|
|
|
/* map uart2 pins */
|
|
uart2_pins: pinmux_uart2_pins {
|
|
pinctrl-single,pins = <
|
|
0xd8 0x118
|
|
0xda 0
|
|
0xdc 0x118
|
|
0xde 0
|
|
>;
|
|
};
|
|
};
|
|
|
|
&control_devconf0 {
|
|
mcbsp1_pins: pinmux_mcbsp1_pins {
|
|
pinctrl-single,bits = <
|
|
0x00 0x18 0x18 /* FSR/CLKR signal from FSX/CLKX pin */
|
|
>;
|
|
};
|
|
|
|
mcbsp2_clks_pins: pinmux_mcbsp2_clks_pins {
|
|
pinctrl-single,bits = <
|
|
0x00 0x40 0x40 /* McBSP2 CLKS from McBSP_CLKS pin */
|
|
>;
|
|
};
|
|
|
|
};
|
|
|
|
&uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pins>;
|
|
};
|
|
|
|
&uart2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart2_pins>;
|
|
};
|