WSL2-Linux-Kernel/arch/arm/mach-realview/platsmp.c

255 строки
5.7 KiB
C

/*
* linux/arch/arm/mach-realview/platsmp.c
*
* Copyright (C) 2002 ARM Ltd.
* All Rights Reserved
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/jiffies.h>
#include <linux/smp.h>
#include <linux/io.h>
#include <asm/cacheflush.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <mach/board-eb.h>
#include <mach/board-pb11mp.h>
#include <mach/scu.h>
#include "core.h"
extern void realview_secondary_startup(void);
/*
* control for which core is the next to come out of the secondary
* boot "holding pen"
*/
volatile int __cpuinitdata pen_release = -1;
static void __iomem *scu_base_addr(void)
{
if (machine_is_realview_eb_mp())
return __io_address(REALVIEW_EB11MP_SCU_BASE);
else if (machine_is_realview_pb11mp())
return __io_address(REALVIEW_TC11MP_SCU_BASE);
else
return (void __iomem *)0;
}
static unsigned int __init get_core_count(void)
{
unsigned int ncores;
void __iomem *scu_base = scu_base_addr();
if (scu_base) {
ncores = __raw_readl(scu_base + SCU_CONFIG);
ncores = (ncores & 0x03) + 1;
} else
ncores = 1;
return ncores;
}
/*
* Setup the SCU
*/
static void scu_enable(void)
{
u32 scu_ctrl;
void __iomem *scu_base = scu_base_addr();
scu_ctrl = __raw_readl(scu_base + SCU_CTRL);
scu_ctrl |= 1;
__raw_writel(scu_ctrl, scu_base + SCU_CTRL);
}
static DEFINE_SPINLOCK(boot_lock);
void __cpuinit platform_secondary_init(unsigned int cpu)
{
trace_hardirqs_off();
/*
* the primary core may have used a "cross call" soft interrupt
* to get this processor out of WFI in the BootMonitor - make
* sure that we are no longer being sent this soft interrupt
*/
smp_cross_call_done(cpumask_of_cpu(cpu));
/*
* if any interrupts are already enabled for the primary
* core (e.g. timer irq), then they will not have been enabled
* for us: do so
*/
gic_cpu_init(0, gic_cpu_base_addr);
/*
* let the primary processor know we're out of the
* pen, then head off into the C entry point
*/
pen_release = -1;
smp_wmb();
/*
* Synchronise with the boot thread.
*/
spin_lock(&boot_lock);
spin_unlock(&boot_lock);
}
int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned long timeout;
/*
* set synchronisation state between this boot processor
* and the secondary one
*/
spin_lock(&boot_lock);
/*
* The secondary processor is waiting to be released from
* the holding pen - release it, then wait for it to flag
* that it has been released by resetting pen_release.
*
* Note that "pen_release" is the hardware CPU ID, whereas
* "cpu" is Linux's internal ID.
*/
pen_release = cpu;
flush_cache_all();
/*
* XXX
*
* This is a later addition to the booting protocol: the
* bootMonitor now puts secondary cores into WFI, so
* poke_milo() no longer gets the cores moving; we need
* to send a soft interrupt to wake the secondary core.
* Use smp_cross_call() for this, since there's little
* point duplicating the code here
*/
smp_cross_call(cpumask_of_cpu(cpu));
timeout = jiffies + (1 * HZ);
while (time_before(jiffies, timeout)) {
smp_rmb();
if (pen_release == -1)
break;
udelay(10);
}
/*
* now the secondary core is starting up let it run its
* calibrations, then wait for it to finish
*/
spin_unlock(&boot_lock);
return pen_release != -1 ? -ENOSYS : 0;
}
static void __init poke_milo(void)
{
extern void secondary_startup(void);
/* nobody is to be released from the pen yet */
pen_release = -1;
/*
* write the address of secondary startup into the system-wide
* flags register, then clear the bottom two bits, which is what
* BootMonitor is waiting for
*/
#if 1
#define REALVIEW_SYS_FLAGSS_OFFSET 0x30
__raw_writel(virt_to_phys(realview_secondary_startup),
__io_address(REALVIEW_SYS_BASE) +
REALVIEW_SYS_FLAGSS_OFFSET);
#define REALVIEW_SYS_FLAGSC_OFFSET 0x34
__raw_writel(3,
__io_address(REALVIEW_SYS_BASE) +
REALVIEW_SYS_FLAGSC_OFFSET);
#endif
mb();
}
/*
* Initialise the CPU possible map early - this describes the CPUs
* which may be present or become present in the system.
*/
void __init smp_init_cpus(void)
{
unsigned int i, ncores = get_core_count();
for (i = 0; i < ncores; i++)
cpu_set(i, cpu_possible_map);
}
void __init smp_prepare_cpus(unsigned int max_cpus)
{
unsigned int ncores = get_core_count();
unsigned int cpu = smp_processor_id();
int i;
/* sanity check */
if (ncores == 0) {
printk(KERN_ERR
"Realview: strange CM count of 0? Default to 1\n");
ncores = 1;
}
if (ncores > NR_CPUS) {
printk(KERN_WARNING
"Realview: no. of cores (%d) greater than configured "
"maximum of %d - clipping\n",
ncores, NR_CPUS);
ncores = NR_CPUS;
}
smp_store_cpu_info(cpu);
/*
* are we trying to boot more cores than exist?
*/
if (max_cpus > ncores)
max_cpus = ncores;
#ifdef CONFIG_LOCAL_TIMERS
/*
* Enable the local timer for primary CPU. If the device is
* dummy (!CONFIG_LOCAL_TIMERS), it was already registers in
* realview_timer_init
*/
local_timer_setup();
#endif
/*
* Initialise the present map, which describes the set of CPUs
* actually populated at the present time.
*/
for (i = 0; i < max_cpus; i++)
cpu_set(i, cpu_present_map);
/*
* Initialise the SCU if there are more than one CPU and let
* them know where to start. Note that, on modern versions of
* MILO, the "poke" doesn't actually do anything until each
* individual core is sent a soft interrupt to get it out of
* WFI
*/
if (max_cpus > 1) {
scu_enable();
poke_milo();
}
}