WSL2-Linux-Kernel/arch/arm/mach-pxa/standby.S

112 строки
2.6 KiB
ArmAsm

/* SPDX-License-Identifier: GPL-2.0-only */
/*
* PXA27x standby mode
*
* Author: David Burrage
*
* 2005 (c) MontaVista Software, Inc.
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
#include "pxa2xx-regs.h"
.text
#ifdef CONFIG_PXA27x
ENTRY(pxa_cpu_standby)
ldr r0, =PSSR
mov r1, #(PSSR_PH | PSSR_STS)
mov r2, #PWRMODE_STANDBY
mov r3, #UNCACHED_PHYS_0 @ Read mem context in.
ldr ip, [r3]
b 1f
.align 5
1: mcr p14, 0, r2, c7, c0, 0 @ put the system into Standby
str r1, [r0] @ make sure PSSR_PH/STS are clear
ret lr
#endif
#ifdef CONFIG_PXA3xx
#define PXA3_MDCNFG 0x0000
#define PXA3_MDCNFG_DMCEN (1 << 30)
#define PXA3_DDR_HCAL 0x0060
#define PXA3_DDR_HCAL_HCRNG 0x1f
#define PXA3_DDR_HCAL_HCPROG (1 << 28)
#define PXA3_DDR_HCAL_HCEN (1 << 31)
#define PXA3_DMCIER 0x0070
#define PXA3_DMCIER_EDLP (1 << 29)
#define PXA3_DMCISR 0x0078
#define PXA3_RCOMP 0x0100
#define PXA3_RCOMP_SWEVAL (1 << 31)
ENTRY(pm_enter_standby_start)
mov r1, #0xf6000000 @ DMEMC_REG_BASE (PXA3_MDCNFG)
add r1, r1, #0x00100000
/*
* Preload the TLB entry for accessing the dynamic memory
* controller registers. Note that page table lookups will
* fail until the dynamic memory controller has been
* reinitialised - and that includes MMU page table walks.
* This also means that only the dynamic memory controller
* can be reliably accessed in the code following standby.
*/
ldr r2, [r1] @ Dummy read PXA3_MDCNFG
mcr p14, 0, r0, c7, c0, 0
.rept 8
nop
.endr
ldr r0, [r1, #PXA3_DDR_HCAL] @ Clear (and wait for) HCEN
bic r0, r0, #PXA3_DDR_HCAL_HCEN
str r0, [r1, #PXA3_DDR_HCAL]
1: ldr r0, [r1, #PXA3_DDR_HCAL]
tst r0, #PXA3_DDR_HCAL_HCEN
bne 1b
ldr r0, [r1, #PXA3_RCOMP] @ Initiate RCOMP
orr r0, r0, #PXA3_RCOMP_SWEVAL
str r0, [r1, #PXA3_RCOMP]
mov r0, #~0 @ Clear interrupts
str r0, [r1, #PXA3_DMCISR]
ldr r0, [r1, #PXA3_DMCIER] @ set DMIER[EDLP]
orr r0, r0, #PXA3_DMCIER_EDLP
str r0, [r1, #PXA3_DMCIER]
ldr r0, [r1, #PXA3_DDR_HCAL] @ clear HCRNG, set HCPROG, HCEN
bic r0, r0, #PXA3_DDR_HCAL_HCRNG
orr r0, r0, #PXA3_DDR_HCAL_HCEN | PXA3_DDR_HCAL_HCPROG
str r0, [r1, #PXA3_DDR_HCAL]
1: ldr r0, [r1, #PXA3_DMCISR]
tst r0, #PXA3_DMCIER_EDLP
beq 1b
ldr r0, [r1, #PXA3_MDCNFG] @ set PXA3_MDCNFG[DMCEN]
orr r0, r0, #PXA3_MDCNFG_DMCEN
str r0, [r1, #PXA3_MDCNFG]
1: ldr r0, [r1, #PXA3_MDCNFG]
tst r0, #PXA3_MDCNFG_DMCEN
beq 1b
ldr r0, [r1, #PXA3_DDR_HCAL] @ set PXA3_DDR_HCAL[HCRNG]
orr r0, r0, #2 @ HCRNG
str r0, [r1, #PXA3_DDR_HCAL]
ldr r0, [r1, #PXA3_DMCIER] @ Clear the interrupt
bic r0, r0, #0x20000000
str r0, [r1, #PXA3_DMCIER]
ret lr
ENTRY(pm_enter_standby_end)
#endif