293 строки
7.7 KiB
C
293 строки
7.7 KiB
C
/*
|
|
* Support for periodic interrupts (100 per second) and for getting
|
|
* the current time from the RTC on Power Macintoshes.
|
|
*
|
|
* We use the decrementer register for our periodic interrupts.
|
|
*
|
|
* Paul Mackerras August 1996.
|
|
* Copyright (C) 1996 Paul Mackerras.
|
|
*/
|
|
#include <linux/config.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/param.h>
|
|
#include <linux/string.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/init.h>
|
|
#include <linux/time.h>
|
|
#include <linux/adb.h>
|
|
#include <linux/cuda.h>
|
|
#include <linux/pmu.h>
|
|
#include <linux/hardirq.h>
|
|
|
|
#include <asm/sections.h>
|
|
#include <asm/prom.h>
|
|
#include <asm/system.h>
|
|
#include <asm/io.h>
|
|
#include <asm/pgtable.h>
|
|
#include <asm/machdep.h>
|
|
#include <asm/time.h>
|
|
#include <asm/nvram.h>
|
|
|
|
/* Apparently the RTC stores seconds since 1 Jan 1904 */
|
|
#define RTC_OFFSET 2082844800
|
|
|
|
/*
|
|
* Calibrate the decrementer frequency with the VIA timer 1.
|
|
*/
|
|
#define VIA_TIMER_FREQ_6 4700000 /* time 1 frequency * 6 */
|
|
|
|
/* VIA registers */
|
|
#define RS 0x200 /* skip between registers */
|
|
#define T1CL (4*RS) /* Timer 1 ctr/latch (low 8 bits) */
|
|
#define T1CH (5*RS) /* Timer 1 counter (high 8 bits) */
|
|
#define T1LL (6*RS) /* Timer 1 latch (low 8 bits) */
|
|
#define T1LH (7*RS) /* Timer 1 latch (high 8 bits) */
|
|
#define ACR (11*RS) /* Auxiliary control register */
|
|
#define IFR (13*RS) /* Interrupt flag register */
|
|
|
|
/* Bits in ACR */
|
|
#define T1MODE 0xc0 /* Timer 1 mode */
|
|
#define T1MODE_CONT 0x40 /* continuous interrupts */
|
|
|
|
/* Bits in IFR and IER */
|
|
#define T1_INT 0x40 /* Timer 1 interrupt */
|
|
|
|
extern struct timezone sys_tz;
|
|
|
|
long __init
|
|
pmac_time_init(void)
|
|
{
|
|
#ifdef CONFIG_NVRAM
|
|
s32 delta = 0;
|
|
int dst;
|
|
|
|
delta = ((s32)pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0x9)) << 16;
|
|
delta |= ((s32)pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0xa)) << 8;
|
|
delta |= pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0xb);
|
|
if (delta & 0x00800000UL)
|
|
delta |= 0xFF000000UL;
|
|
dst = ((pmac_xpram_read(PMAC_XPRAM_MACHINE_LOC + 0x8) & 0x80) != 0);
|
|
printk("GMT Delta read from XPRAM: %d minutes, DST: %s\n", delta/60,
|
|
dst ? "on" : "off");
|
|
return delta;
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
unsigned long __pmac
|
|
pmac_get_rtc_time(void)
|
|
{
|
|
#if defined(CONFIG_ADB_CUDA) || defined(CONFIG_ADB_PMU)
|
|
struct adb_request req;
|
|
unsigned long now;
|
|
#endif
|
|
|
|
/* Get the time from the RTC */
|
|
switch (sys_ctrler) {
|
|
#ifdef CONFIG_ADB_CUDA
|
|
case SYS_CTRLER_CUDA:
|
|
if (cuda_request(&req, NULL, 2, CUDA_PACKET, CUDA_GET_TIME) < 0)
|
|
return 0;
|
|
while (!req.complete)
|
|
cuda_poll();
|
|
if (req.reply_len != 7)
|
|
printk(KERN_ERR "pmac_get_rtc_time: got %d byte reply\n",
|
|
req.reply_len);
|
|
now = (req.reply[3] << 24) + (req.reply[4] << 16)
|
|
+ (req.reply[5] << 8) + req.reply[6];
|
|
return now - RTC_OFFSET;
|
|
#endif /* CONFIG_ADB_CUDA */
|
|
#ifdef CONFIG_ADB_PMU
|
|
case SYS_CTRLER_PMU:
|
|
if (pmu_request(&req, NULL, 1, PMU_READ_RTC) < 0)
|
|
return 0;
|
|
while (!req.complete)
|
|
pmu_poll();
|
|
if (req.reply_len != 4)
|
|
printk(KERN_ERR "pmac_get_rtc_time: got %d byte reply\n",
|
|
req.reply_len);
|
|
now = (req.reply[0] << 24) + (req.reply[1] << 16)
|
|
+ (req.reply[2] << 8) + req.reply[3];
|
|
return now - RTC_OFFSET;
|
|
#endif /* CONFIG_ADB_PMU */
|
|
default: ;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
int __pmac
|
|
pmac_set_rtc_time(unsigned long nowtime)
|
|
{
|
|
#if defined(CONFIG_ADB_CUDA) || defined(CONFIG_ADB_PMU)
|
|
struct adb_request req;
|
|
#endif
|
|
|
|
nowtime += RTC_OFFSET;
|
|
|
|
switch (sys_ctrler) {
|
|
#ifdef CONFIG_ADB_CUDA
|
|
case SYS_CTRLER_CUDA:
|
|
if (cuda_request(&req, NULL, 6, CUDA_PACKET, CUDA_SET_TIME,
|
|
nowtime >> 24, nowtime >> 16, nowtime >> 8, nowtime) < 0)
|
|
return 0;
|
|
while (!req.complete)
|
|
cuda_poll();
|
|
if ((req.reply_len != 3) && (req.reply_len != 7))
|
|
printk(KERN_ERR "pmac_set_rtc_time: got %d byte reply\n",
|
|
req.reply_len);
|
|
return 1;
|
|
#endif /* CONFIG_ADB_CUDA */
|
|
#ifdef CONFIG_ADB_PMU
|
|
case SYS_CTRLER_PMU:
|
|
if (pmu_request(&req, NULL, 5, PMU_SET_RTC,
|
|
nowtime >> 24, nowtime >> 16, nowtime >> 8, nowtime) < 0)
|
|
return 0;
|
|
while (!req.complete)
|
|
pmu_poll();
|
|
if (req.reply_len != 0)
|
|
printk(KERN_ERR "pmac_set_rtc_time: got %d byte reply\n",
|
|
req.reply_len);
|
|
return 1;
|
|
#endif /* CONFIG_ADB_PMU */
|
|
default:
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Calibrate the decrementer register using VIA timer 1.
|
|
* This is used both on powermacs and CHRP machines.
|
|
*/
|
|
int __init
|
|
via_calibrate_decr(void)
|
|
{
|
|
struct device_node *vias;
|
|
volatile unsigned char *via;
|
|
int count = VIA_TIMER_FREQ_6 / 100;
|
|
unsigned int dstart, dend;
|
|
|
|
vias = find_devices("via-cuda");
|
|
if (vias == 0)
|
|
vias = find_devices("via-pmu");
|
|
if (vias == 0)
|
|
vias = find_devices("via");
|
|
if (vias == 0 || vias->n_addrs == 0)
|
|
return 0;
|
|
via = (volatile unsigned char *)
|
|
ioremap(vias->addrs[0].address, vias->addrs[0].size);
|
|
|
|
/* set timer 1 for continuous interrupts */
|
|
out_8(&via[ACR], (via[ACR] & ~T1MODE) | T1MODE_CONT);
|
|
/* set the counter to a small value */
|
|
out_8(&via[T1CH], 2);
|
|
/* set the latch to `count' */
|
|
out_8(&via[T1LL], count);
|
|
out_8(&via[T1LH], count >> 8);
|
|
/* wait until it hits 0 */
|
|
while ((in_8(&via[IFR]) & T1_INT) == 0)
|
|
;
|
|
dstart = get_dec();
|
|
/* clear the interrupt & wait until it hits 0 again */
|
|
in_8(&via[T1CL]);
|
|
while ((in_8(&via[IFR]) & T1_INT) == 0)
|
|
;
|
|
dend = get_dec();
|
|
|
|
tb_ticks_per_jiffy = (dstart - dend) / (6 * (HZ/100));
|
|
tb_to_us = mulhwu_scale_factor(dstart - dend, 60000);
|
|
|
|
printk(KERN_INFO "via_calibrate_decr: ticks per jiffy = %u (%u ticks)\n",
|
|
tb_ticks_per_jiffy, dstart - dend);
|
|
|
|
iounmap((void*)via);
|
|
|
|
return 1;
|
|
}
|
|
|
|
#ifdef CONFIG_PMAC_PBOOK
|
|
/*
|
|
* Reset the time after a sleep.
|
|
*/
|
|
static int __pmac
|
|
time_sleep_notify(struct pmu_sleep_notifier *self, int when)
|
|
{
|
|
static unsigned long time_diff;
|
|
unsigned long flags;
|
|
unsigned long seq;
|
|
|
|
switch (when) {
|
|
case PBOOK_SLEEP_NOW:
|
|
do {
|
|
seq = read_seqbegin_irqsave(&xtime_lock, flags);
|
|
time_diff = xtime.tv_sec - pmac_get_rtc_time();
|
|
} while (read_seqretry_irqrestore(&xtime_lock, seq, flags));
|
|
break;
|
|
case PBOOK_WAKE:
|
|
write_seqlock_irqsave(&xtime_lock, flags);
|
|
xtime.tv_sec = pmac_get_rtc_time() + time_diff;
|
|
xtime.tv_nsec = 0;
|
|
last_rtc_update = xtime.tv_sec;
|
|
write_sequnlock_irqrestore(&xtime_lock, flags);
|
|
break;
|
|
}
|
|
return PBOOK_SLEEP_OK;
|
|
}
|
|
|
|
static struct pmu_sleep_notifier time_sleep_notifier __pmacdata = {
|
|
time_sleep_notify, SLEEP_LEVEL_MISC,
|
|
};
|
|
#endif /* CONFIG_PMAC_PBOOK */
|
|
|
|
/*
|
|
* Query the OF and get the decr frequency.
|
|
* This was taken from the pmac time_init() when merging the prep/pmac
|
|
* time functions.
|
|
*/
|
|
void __init
|
|
pmac_calibrate_decr(void)
|
|
{
|
|
struct device_node *cpu;
|
|
unsigned int freq, *fp;
|
|
|
|
#ifdef CONFIG_PMAC_PBOOK
|
|
pmu_register_sleep_notifier(&time_sleep_notifier);
|
|
#endif /* CONFIG_PMAC_PBOOK */
|
|
|
|
/* We assume MacRISC2 machines have correct device-tree
|
|
* calibration. That's better since the VIA itself seems
|
|
* to be slightly off. --BenH
|
|
*/
|
|
if (!machine_is_compatible("MacRISC2") &&
|
|
!machine_is_compatible("MacRISC3") &&
|
|
!machine_is_compatible("MacRISC4"))
|
|
if (via_calibrate_decr())
|
|
return;
|
|
|
|
/* Special case: QuickSilver G4s seem to have a badly calibrated
|
|
* timebase-frequency in OF, VIA is much better on these. We should
|
|
* probably implement calibration based on the KL timer on these
|
|
* machines anyway... -BenH
|
|
*/
|
|
if (machine_is_compatible("PowerMac3,5"))
|
|
if (via_calibrate_decr())
|
|
return;
|
|
/*
|
|
* The cpu node should have a timebase-frequency property
|
|
* to tell us the rate at which the decrementer counts.
|
|
*/
|
|
cpu = find_type_devices("cpu");
|
|
if (cpu == 0)
|
|
panic("can't find cpu node in time_init");
|
|
fp = (unsigned int *) get_property(cpu, "timebase-frequency", NULL);
|
|
if (fp == 0)
|
|
panic("can't get cpu timebase frequency");
|
|
freq = *fp;
|
|
printk("time_init: decrementer frequency = %u.%.6u MHz\n",
|
|
freq/1000000, freq%1000000);
|
|
tb_ticks_per_jiffy = freq / HZ;
|
|
tb_to_us = mulhwu_scale_factor(freq, 1000000);
|
|
}
|