573 строки
15 KiB
C
573 строки
15 KiB
C
// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
|
|
/*
|
|
* PWM controller driver for Amlogic Meson SoCs.
|
|
*
|
|
* This PWM is only a set of Gates, Dividers and Counters:
|
|
* PWM output is achieved by calculating a clock that permits calculating
|
|
* two periods (low and high). The counter then has to be set to switch after
|
|
* N cycles for the first half period.
|
|
* The hardware has no "polarity" setting. This driver reverses the period
|
|
* cycles (the low length is inverted with the high length) for
|
|
* PWM_POLARITY_INVERSED. This means that .get_state cannot read the polarity
|
|
* from the hardware.
|
|
* Setting the duty cycle will disable and re-enable the PWM output.
|
|
* Disabling the PWM stops the output immediately (without waiting for the
|
|
* current period to complete first).
|
|
*
|
|
* The public S912 (GXM) datasheet contains some documentation for this PWM
|
|
* controller starting on page 543:
|
|
* https://dl.khadas.com/Hardware/VIM2/Datasheet/S912_Datasheet_V0.220170314publicversion-Wesion.pdf
|
|
* An updated version of this IP block is found in S922X (G12B) SoCs. The
|
|
* datasheet contains the description for this IP block revision starting at
|
|
* page 1084:
|
|
* https://dn.odroid.com/S922X/ODROID-N2/Datasheet/S922X_Public_Datasheet_V0.2.pdf
|
|
*
|
|
* Copyright (c) 2016 BayLibre, SAS.
|
|
* Author: Neil Armstrong <narmstrong@baylibre.com>
|
|
* Copyright (C) 2014 Amlogic, Inc.
|
|
*/
|
|
|
|
#include <linux/bitfield.h>
|
|
#include <linux/bits.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/clk-provider.h>
|
|
#include <linux/err.h>
|
|
#include <linux/io.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/math64.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pwm.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/spinlock.h>
|
|
|
|
#define REG_PWM_A 0x0
|
|
#define REG_PWM_B 0x4
|
|
#define PWM_LOW_MASK GENMASK(15, 0)
|
|
#define PWM_HIGH_MASK GENMASK(31, 16)
|
|
|
|
#define REG_MISC_AB 0x8
|
|
#define MISC_B_CLK_EN BIT(23)
|
|
#define MISC_A_CLK_EN BIT(15)
|
|
#define MISC_CLK_DIV_MASK 0x7f
|
|
#define MISC_B_CLK_DIV_SHIFT 16
|
|
#define MISC_A_CLK_DIV_SHIFT 8
|
|
#define MISC_B_CLK_SEL_SHIFT 6
|
|
#define MISC_A_CLK_SEL_SHIFT 4
|
|
#define MISC_CLK_SEL_MASK 0x3
|
|
#define MISC_B_EN BIT(1)
|
|
#define MISC_A_EN BIT(0)
|
|
|
|
#define MESON_NUM_PWMS 2
|
|
|
|
static struct meson_pwm_channel_data {
|
|
u8 reg_offset;
|
|
u8 clk_sel_shift;
|
|
u8 clk_div_shift;
|
|
u32 clk_en_mask;
|
|
u32 pwm_en_mask;
|
|
} meson_pwm_per_channel_data[MESON_NUM_PWMS] = {
|
|
{
|
|
.reg_offset = REG_PWM_A,
|
|
.clk_sel_shift = MISC_A_CLK_SEL_SHIFT,
|
|
.clk_div_shift = MISC_A_CLK_DIV_SHIFT,
|
|
.clk_en_mask = MISC_A_CLK_EN,
|
|
.pwm_en_mask = MISC_A_EN,
|
|
},
|
|
{
|
|
.reg_offset = REG_PWM_B,
|
|
.clk_sel_shift = MISC_B_CLK_SEL_SHIFT,
|
|
.clk_div_shift = MISC_B_CLK_DIV_SHIFT,
|
|
.clk_en_mask = MISC_B_CLK_EN,
|
|
.pwm_en_mask = MISC_B_EN,
|
|
}
|
|
};
|
|
|
|
struct meson_pwm_channel {
|
|
unsigned int hi;
|
|
unsigned int lo;
|
|
u8 pre_div;
|
|
|
|
struct clk *clk_parent;
|
|
struct clk_mux mux;
|
|
struct clk *clk;
|
|
};
|
|
|
|
struct meson_pwm_data {
|
|
const char * const *parent_names;
|
|
unsigned int num_parents;
|
|
};
|
|
|
|
struct meson_pwm {
|
|
struct pwm_chip chip;
|
|
const struct meson_pwm_data *data;
|
|
struct meson_pwm_channel channels[MESON_NUM_PWMS];
|
|
void __iomem *base;
|
|
/*
|
|
* Protects register (write) access to the REG_MISC_AB register
|
|
* that is shared between the two PWMs.
|
|
*/
|
|
spinlock_t lock;
|
|
};
|
|
|
|
static inline struct meson_pwm *to_meson_pwm(struct pwm_chip *chip)
|
|
{
|
|
return container_of(chip, struct meson_pwm, chip);
|
|
}
|
|
|
|
static int meson_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
|
|
{
|
|
struct meson_pwm *meson = to_meson_pwm(chip);
|
|
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
|
|
struct device *dev = chip->dev;
|
|
int err;
|
|
|
|
if (channel->clk_parent) {
|
|
err = clk_set_parent(channel->clk, channel->clk_parent);
|
|
if (err < 0) {
|
|
dev_err(dev, "failed to set parent %s for %s: %d\n",
|
|
__clk_get_name(channel->clk_parent),
|
|
__clk_get_name(channel->clk), err);
|
|
return err;
|
|
}
|
|
}
|
|
|
|
err = clk_prepare_enable(channel->clk);
|
|
if (err < 0) {
|
|
dev_err(dev, "failed to enable clock %s: %d\n",
|
|
__clk_get_name(channel->clk), err);
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void meson_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
|
|
{
|
|
struct meson_pwm *meson = to_meson_pwm(chip);
|
|
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
|
|
|
|
clk_disable_unprepare(channel->clk);
|
|
}
|
|
|
|
static int meson_pwm_calc(struct meson_pwm *meson, struct pwm_device *pwm,
|
|
const struct pwm_state *state)
|
|
{
|
|
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
|
|
unsigned int duty, period, pre_div, cnt, duty_cnt;
|
|
unsigned long fin_freq;
|
|
|
|
duty = state->duty_cycle;
|
|
period = state->period;
|
|
|
|
if (state->polarity == PWM_POLARITY_INVERSED)
|
|
duty = period - duty;
|
|
|
|
fin_freq = clk_get_rate(channel->clk);
|
|
if (fin_freq == 0) {
|
|
dev_err(meson->chip.dev, "invalid source clock frequency\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
dev_dbg(meson->chip.dev, "fin_freq: %lu Hz\n", fin_freq);
|
|
|
|
pre_div = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * 0xffffLL);
|
|
if (pre_div > MISC_CLK_DIV_MASK) {
|
|
dev_err(meson->chip.dev, "unable to get period pre_div\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
cnt = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * (pre_div + 1));
|
|
if (cnt > 0xffff) {
|
|
dev_err(meson->chip.dev, "unable to get period cnt\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
dev_dbg(meson->chip.dev, "period=%u pre_div=%u cnt=%u\n", period,
|
|
pre_div, cnt);
|
|
|
|
if (duty == period) {
|
|
channel->pre_div = pre_div;
|
|
channel->hi = cnt;
|
|
channel->lo = 0;
|
|
} else if (duty == 0) {
|
|
channel->pre_div = pre_div;
|
|
channel->hi = 0;
|
|
channel->lo = cnt;
|
|
} else {
|
|
/* Then check is we can have the duty with the same pre_div */
|
|
duty_cnt = div64_u64(fin_freq * (u64)duty,
|
|
NSEC_PER_SEC * (pre_div + 1));
|
|
if (duty_cnt > 0xffff) {
|
|
dev_err(meson->chip.dev, "unable to get duty cycle\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
dev_dbg(meson->chip.dev, "duty=%u pre_div=%u duty_cnt=%u\n",
|
|
duty, pre_div, duty_cnt);
|
|
|
|
channel->pre_div = pre_div;
|
|
channel->hi = duty_cnt;
|
|
channel->lo = cnt - duty_cnt;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void meson_pwm_enable(struct meson_pwm *meson, struct pwm_device *pwm)
|
|
{
|
|
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
|
|
struct meson_pwm_channel_data *channel_data;
|
|
unsigned long flags;
|
|
u32 value;
|
|
|
|
channel_data = &meson_pwm_per_channel_data[pwm->hwpwm];
|
|
|
|
spin_lock_irqsave(&meson->lock, flags);
|
|
|
|
value = readl(meson->base + REG_MISC_AB);
|
|
value &= ~(MISC_CLK_DIV_MASK << channel_data->clk_div_shift);
|
|
value |= channel->pre_div << channel_data->clk_div_shift;
|
|
value |= channel_data->clk_en_mask;
|
|
writel(value, meson->base + REG_MISC_AB);
|
|
|
|
value = FIELD_PREP(PWM_HIGH_MASK, channel->hi) |
|
|
FIELD_PREP(PWM_LOW_MASK, channel->lo);
|
|
writel(value, meson->base + channel_data->reg_offset);
|
|
|
|
value = readl(meson->base + REG_MISC_AB);
|
|
value |= channel_data->pwm_en_mask;
|
|
writel(value, meson->base + REG_MISC_AB);
|
|
|
|
spin_unlock_irqrestore(&meson->lock, flags);
|
|
}
|
|
|
|
static void meson_pwm_disable(struct meson_pwm *meson, struct pwm_device *pwm)
|
|
{
|
|
unsigned long flags;
|
|
u32 value;
|
|
|
|
spin_lock_irqsave(&meson->lock, flags);
|
|
|
|
value = readl(meson->base + REG_MISC_AB);
|
|
value &= ~meson_pwm_per_channel_data[pwm->hwpwm].pwm_en_mask;
|
|
writel(value, meson->base + REG_MISC_AB);
|
|
|
|
spin_unlock_irqrestore(&meson->lock, flags);
|
|
}
|
|
|
|
static int meson_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
|
|
const struct pwm_state *state)
|
|
{
|
|
struct meson_pwm *meson = to_meson_pwm(chip);
|
|
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
|
|
int err = 0;
|
|
|
|
if (!state->enabled) {
|
|
if (state->polarity == PWM_POLARITY_INVERSED) {
|
|
/*
|
|
* This IP block revision doesn't have an "always high"
|
|
* setting which we can use for "inverted disabled".
|
|
* Instead we achieve this using the same settings
|
|
* that we use a pre_div of 0 (to get the shortest
|
|
* possible duration for one "count") and
|
|
* "period == duty_cycle". This results in a signal
|
|
* which is LOW for one "count", while being HIGH for
|
|
* the rest of the (so the signal is HIGH for slightly
|
|
* less than 100% of the period, but this is the best
|
|
* we can achieve).
|
|
*/
|
|
channel->pre_div = 0;
|
|
channel->hi = ~0;
|
|
channel->lo = 0;
|
|
|
|
meson_pwm_enable(meson, pwm);
|
|
} else {
|
|
meson_pwm_disable(meson, pwm);
|
|
}
|
|
} else {
|
|
err = meson_pwm_calc(meson, pwm, state);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
meson_pwm_enable(meson, pwm);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int meson_pwm_cnt_to_ns(struct pwm_chip *chip,
|
|
struct pwm_device *pwm, u32 cnt)
|
|
{
|
|
struct meson_pwm *meson = to_meson_pwm(chip);
|
|
struct meson_pwm_channel *channel;
|
|
unsigned long fin_freq;
|
|
u32 fin_ns;
|
|
|
|
/* to_meson_pwm() can only be used after .get_state() is called */
|
|
channel = &meson->channels[pwm->hwpwm];
|
|
|
|
fin_freq = clk_get_rate(channel->clk);
|
|
if (fin_freq == 0)
|
|
return 0;
|
|
|
|
fin_ns = div_u64(NSEC_PER_SEC, fin_freq);
|
|
|
|
return cnt * fin_ns * (channel->pre_div + 1);
|
|
}
|
|
|
|
static void meson_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
|
|
struct pwm_state *state)
|
|
{
|
|
struct meson_pwm *meson = to_meson_pwm(chip);
|
|
struct meson_pwm_channel_data *channel_data;
|
|
struct meson_pwm_channel *channel;
|
|
u32 value, tmp;
|
|
|
|
if (!state)
|
|
return;
|
|
|
|
channel = &meson->channels[pwm->hwpwm];
|
|
channel_data = &meson_pwm_per_channel_data[pwm->hwpwm];
|
|
|
|
value = readl(meson->base + REG_MISC_AB);
|
|
|
|
tmp = channel_data->pwm_en_mask | channel_data->clk_en_mask;
|
|
state->enabled = (value & tmp) == tmp;
|
|
|
|
tmp = value >> channel_data->clk_div_shift;
|
|
channel->pre_div = FIELD_GET(MISC_CLK_DIV_MASK, tmp);
|
|
|
|
value = readl(meson->base + channel_data->reg_offset);
|
|
|
|
channel->lo = FIELD_GET(PWM_LOW_MASK, value);
|
|
channel->hi = FIELD_GET(PWM_HIGH_MASK, value);
|
|
|
|
if (channel->lo == 0) {
|
|
state->period = meson_pwm_cnt_to_ns(chip, pwm, channel->hi);
|
|
state->duty_cycle = state->period;
|
|
} else if (channel->lo >= channel->hi) {
|
|
state->period = meson_pwm_cnt_to_ns(chip, pwm,
|
|
channel->lo + channel->hi);
|
|
state->duty_cycle = meson_pwm_cnt_to_ns(chip, pwm,
|
|
channel->hi);
|
|
} else {
|
|
state->period = 0;
|
|
state->duty_cycle = 0;
|
|
}
|
|
}
|
|
|
|
static const struct pwm_ops meson_pwm_ops = {
|
|
.request = meson_pwm_request,
|
|
.free = meson_pwm_free,
|
|
.apply = meson_pwm_apply,
|
|
.get_state = meson_pwm_get_state,
|
|
.owner = THIS_MODULE,
|
|
};
|
|
|
|
static const char * const pwm_meson8b_parent_names[] = {
|
|
"xtal", "vid_pll", "fclk_div4", "fclk_div3"
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_meson8b_data = {
|
|
.parent_names = pwm_meson8b_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_meson8b_parent_names),
|
|
};
|
|
|
|
static const char * const pwm_gxbb_parent_names[] = {
|
|
"xtal", "hdmi_pll", "fclk_div4", "fclk_div3"
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_gxbb_data = {
|
|
.parent_names = pwm_gxbb_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_gxbb_parent_names),
|
|
};
|
|
|
|
/*
|
|
* Only the 2 first inputs of the GXBB AO PWMs are valid
|
|
* The last 2 are grounded
|
|
*/
|
|
static const char * const pwm_gxbb_ao_parent_names[] = {
|
|
"xtal", "clk81"
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_gxbb_ao_data = {
|
|
.parent_names = pwm_gxbb_ao_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_gxbb_ao_parent_names),
|
|
};
|
|
|
|
static const char * const pwm_axg_ee_parent_names[] = {
|
|
"xtal", "fclk_div5", "fclk_div4", "fclk_div3"
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_axg_ee_data = {
|
|
.parent_names = pwm_axg_ee_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_axg_ee_parent_names),
|
|
};
|
|
|
|
static const char * const pwm_axg_ao_parent_names[] = {
|
|
"aoclk81", "xtal", "fclk_div4", "fclk_div5"
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_axg_ao_data = {
|
|
.parent_names = pwm_axg_ao_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_axg_ao_parent_names),
|
|
};
|
|
|
|
static const char * const pwm_g12a_ao_ab_parent_names[] = {
|
|
"xtal", "aoclk81", "fclk_div4", "fclk_div5"
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_g12a_ao_ab_data = {
|
|
.parent_names = pwm_g12a_ao_ab_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_g12a_ao_ab_parent_names),
|
|
};
|
|
|
|
static const char * const pwm_g12a_ao_cd_parent_names[] = {
|
|
"xtal", "aoclk81",
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_g12a_ao_cd_data = {
|
|
.parent_names = pwm_g12a_ao_cd_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_g12a_ao_cd_parent_names),
|
|
};
|
|
|
|
static const char * const pwm_g12a_ee_parent_names[] = {
|
|
"xtal", "hdmi_pll", "fclk_div4", "fclk_div3"
|
|
};
|
|
|
|
static const struct meson_pwm_data pwm_g12a_ee_data = {
|
|
.parent_names = pwm_g12a_ee_parent_names,
|
|
.num_parents = ARRAY_SIZE(pwm_g12a_ee_parent_names),
|
|
};
|
|
|
|
static const struct of_device_id meson_pwm_matches[] = {
|
|
{
|
|
.compatible = "amlogic,meson8b-pwm",
|
|
.data = &pwm_meson8b_data
|
|
},
|
|
{
|
|
.compatible = "amlogic,meson-gxbb-pwm",
|
|
.data = &pwm_gxbb_data
|
|
},
|
|
{
|
|
.compatible = "amlogic,meson-gxbb-ao-pwm",
|
|
.data = &pwm_gxbb_ao_data
|
|
},
|
|
{
|
|
.compatible = "amlogic,meson-axg-ee-pwm",
|
|
.data = &pwm_axg_ee_data
|
|
},
|
|
{
|
|
.compatible = "amlogic,meson-axg-ao-pwm",
|
|
.data = &pwm_axg_ao_data
|
|
},
|
|
{
|
|
.compatible = "amlogic,meson-g12a-ee-pwm",
|
|
.data = &pwm_g12a_ee_data
|
|
},
|
|
{
|
|
.compatible = "amlogic,meson-g12a-ao-pwm-ab",
|
|
.data = &pwm_g12a_ao_ab_data
|
|
},
|
|
{
|
|
.compatible = "amlogic,meson-g12a-ao-pwm-cd",
|
|
.data = &pwm_g12a_ao_cd_data
|
|
},
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, meson_pwm_matches);
|
|
|
|
static int meson_pwm_init_channels(struct meson_pwm *meson)
|
|
{
|
|
struct device *dev = meson->chip.dev;
|
|
struct clk_init_data init;
|
|
unsigned int i;
|
|
char name[255];
|
|
int err;
|
|
|
|
for (i = 0; i < meson->chip.npwm; i++) {
|
|
struct meson_pwm_channel *channel = &meson->channels[i];
|
|
|
|
snprintf(name, sizeof(name), "%s#mux%u", dev_name(dev), i);
|
|
|
|
init.name = name;
|
|
init.ops = &clk_mux_ops;
|
|
init.flags = 0;
|
|
init.parent_names = meson->data->parent_names;
|
|
init.num_parents = meson->data->num_parents;
|
|
|
|
channel->mux.reg = meson->base + REG_MISC_AB;
|
|
channel->mux.shift =
|
|
meson_pwm_per_channel_data[i].clk_sel_shift;
|
|
channel->mux.mask = MISC_CLK_SEL_MASK;
|
|
channel->mux.flags = 0;
|
|
channel->mux.lock = &meson->lock;
|
|
channel->mux.table = NULL;
|
|
channel->mux.hw.init = &init;
|
|
|
|
channel->clk = devm_clk_register(dev, &channel->mux.hw);
|
|
if (IS_ERR(channel->clk)) {
|
|
err = PTR_ERR(channel->clk);
|
|
dev_err(dev, "failed to register %s: %d\n", name, err);
|
|
return err;
|
|
}
|
|
|
|
snprintf(name, sizeof(name), "clkin%u", i);
|
|
|
|
channel->clk_parent = devm_clk_get_optional(dev, name);
|
|
if (IS_ERR(channel->clk_parent))
|
|
return PTR_ERR(channel->clk_parent);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int meson_pwm_probe(struct platform_device *pdev)
|
|
{
|
|
struct meson_pwm *meson;
|
|
int err;
|
|
|
|
meson = devm_kzalloc(&pdev->dev, sizeof(*meson), GFP_KERNEL);
|
|
if (!meson)
|
|
return -ENOMEM;
|
|
|
|
meson->base = devm_platform_ioremap_resource(pdev, 0);
|
|
if (IS_ERR(meson->base))
|
|
return PTR_ERR(meson->base);
|
|
|
|
spin_lock_init(&meson->lock);
|
|
meson->chip.dev = &pdev->dev;
|
|
meson->chip.ops = &meson_pwm_ops;
|
|
meson->chip.npwm = MESON_NUM_PWMS;
|
|
|
|
meson->data = of_device_get_match_data(&pdev->dev);
|
|
|
|
err = meson_pwm_init_channels(meson);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
err = devm_pwmchip_add(&pdev->dev, &meson->chip);
|
|
if (err < 0) {
|
|
dev_err(&pdev->dev, "failed to register PWM chip: %d\n", err);
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct platform_driver meson_pwm_driver = {
|
|
.driver = {
|
|
.name = "meson-pwm",
|
|
.of_match_table = meson_pwm_matches,
|
|
},
|
|
.probe = meson_pwm_probe,
|
|
};
|
|
module_platform_driver(meson_pwm_driver);
|
|
|
|
MODULE_DESCRIPTION("Amlogic Meson PWM Generator driver");
|
|
MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");
|
|
MODULE_LICENSE("Dual BSD/GPL");
|