135 строки
3.3 KiB
C
135 строки
3.3 KiB
C
/*
|
|
* Unmaintained SGI Visual Workstation support.
|
|
* Split out from setup.c by davej@suse.de
|
|
*/
|
|
|
|
#include <linux/smp.h>
|
|
#include <linux/init.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/interrupt.h>
|
|
|
|
#include <asm/fixmap.h>
|
|
#include <asm/arch_hooks.h>
|
|
#include <asm/io.h>
|
|
#include "cobalt.h"
|
|
#include "piix4.h"
|
|
|
|
char visws_board_type = -1;
|
|
char visws_board_rev = -1;
|
|
|
|
void __init visws_get_board_type_and_rev(void)
|
|
{
|
|
int raw;
|
|
|
|
visws_board_type = (char)(inb_p(PIIX_GPI_BD_REG) & PIIX_GPI_BD_REG)
|
|
>> PIIX_GPI_BD_SHIFT;
|
|
/*
|
|
* Get Board rev.
|
|
* First, we have to initialize the 307 part to allow us access
|
|
* to the GPIO registers. Let's map them at 0x0fc0 which is right
|
|
* after the PIIX4 PM section.
|
|
*/
|
|
outb_p(SIO_DEV_SEL, SIO_INDEX);
|
|
outb_p(SIO_GP_DEV, SIO_DATA); /* Talk to GPIO regs. */
|
|
|
|
outb_p(SIO_DEV_MSB, SIO_INDEX);
|
|
outb_p(SIO_GP_MSB, SIO_DATA); /* MSB of GPIO base address */
|
|
|
|
outb_p(SIO_DEV_LSB, SIO_INDEX);
|
|
outb_p(SIO_GP_LSB, SIO_DATA); /* LSB of GPIO base address */
|
|
|
|
outb_p(SIO_DEV_ENB, SIO_INDEX);
|
|
outb_p(1, SIO_DATA); /* Enable GPIO registers. */
|
|
|
|
/*
|
|
* Now, we have to map the power management section to write
|
|
* a bit which enables access to the GPIO registers.
|
|
* What lunatic came up with this shit?
|
|
*/
|
|
outb_p(SIO_DEV_SEL, SIO_INDEX);
|
|
outb_p(SIO_PM_DEV, SIO_DATA); /* Talk to GPIO regs. */
|
|
|
|
outb_p(SIO_DEV_MSB, SIO_INDEX);
|
|
outb_p(SIO_PM_MSB, SIO_DATA); /* MSB of PM base address */
|
|
|
|
outb_p(SIO_DEV_LSB, SIO_INDEX);
|
|
outb_p(SIO_PM_LSB, SIO_DATA); /* LSB of PM base address */
|
|
|
|
outb_p(SIO_DEV_ENB, SIO_INDEX);
|
|
outb_p(1, SIO_DATA); /* Enable PM registers. */
|
|
|
|
/*
|
|
* Now, write the PM register which enables the GPIO registers.
|
|
*/
|
|
outb_p(SIO_PM_FER2, SIO_PM_INDEX);
|
|
outb_p(SIO_PM_GP_EN, SIO_PM_DATA);
|
|
|
|
/*
|
|
* Now, initialize the GPIO registers.
|
|
* We want them all to be inputs which is the
|
|
* power on default, so let's leave them alone.
|
|
* So, let's just read the board rev!
|
|
*/
|
|
raw = inb_p(SIO_GP_DATA1);
|
|
raw &= 0x7f; /* 7 bits of valid board revision ID. */
|
|
|
|
if (visws_board_type == VISWS_320) {
|
|
if (raw < 0x6) {
|
|
visws_board_rev = 4;
|
|
} else if (raw < 0xc) {
|
|
visws_board_rev = 5;
|
|
} else {
|
|
visws_board_rev = 6;
|
|
}
|
|
} else if (visws_board_type == VISWS_540) {
|
|
visws_board_rev = 2;
|
|
} else {
|
|
visws_board_rev = raw;
|
|
}
|
|
|
|
printk(KERN_INFO "Silicon Graphics Visual Workstation %s (rev %d) detected\n",
|
|
(visws_board_type == VISWS_320 ? "320" :
|
|
(visws_board_type == VISWS_540 ? "540" :
|
|
"unknown")), visws_board_rev);
|
|
}
|
|
|
|
void __init pre_intr_init_hook(void)
|
|
{
|
|
init_VISWS_APIC_irqs();
|
|
}
|
|
|
|
void __init intr_init_hook(void)
|
|
{
|
|
#ifdef CONFIG_X86_LOCAL_APIC
|
|
apic_intr_init();
|
|
#endif
|
|
}
|
|
|
|
void __init pre_setup_arch_hook()
|
|
{
|
|
visws_get_board_type_and_rev();
|
|
}
|
|
|
|
static struct irqaction irq0 = {
|
|
.handler = timer_interrupt,
|
|
.flags = SA_INTERRUPT,
|
|
.name = "timer",
|
|
};
|
|
|
|
void __init time_init_hook(void)
|
|
{
|
|
printk(KERN_INFO "Starting Cobalt Timer system clock\n");
|
|
|
|
/* Set the countdown value */
|
|
co_cpu_write(CO_CPU_TIMEVAL, CO_TIME_HZ/HZ);
|
|
|
|
/* Start the timer */
|
|
co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) | CO_CTRL_TIMERUN);
|
|
|
|
/* Enable (unmask) the timer interrupt */
|
|
co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) & ~CO_CTRL_TIMEMASK);
|
|
|
|
/* Wire cpu IDT entry to s/w handler (and Cobalt APIC to IDT) */
|
|
setup_irq(0, &irq0);
|
|
}
|