WSL2-Linux-Kernel/include/drm/drm_dp_helper.h

402 строки
14 KiB
C

/*
* Copyright © 2008 Keith Packard
*
* Permission to use, copy, modify, distribute, and sell this software and its
* documentation for any purpose is hereby granted without fee, provided that
* the above copyright notice appear in all copies and that both that copyright
* notice and this permission notice appear in supporting documentation, and
* that the name of the copyright holders not be used in advertising or
* publicity pertaining to distribution of the software without specific,
* written prior permission. The copyright holders make no representations
* about the suitability of this software for any purpose. It is provided "as
* is" without express or implied warranty.
*
* THE COPYRIGHT HOLDERS DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE,
* INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO
* EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
* CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE,
* DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
* TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
* OF THIS SOFTWARE.
*/
#ifndef _DRM_DP_HELPER_H_
#define _DRM_DP_HELPER_H_
#include <linux/types.h>
#include <linux/i2c.h>
#include <linux/delay.h>
/*
* Unless otherwise noted, all values are from the DP 1.1a spec. Note that
* DP and DPCD versions are independent. Differences from 1.0 are not noted,
* 1.0 devices basically don't exist in the wild.
*
* Abbreviations, in chronological order:
*
* eDP: Embedded DisplayPort version 1
* DPI: DisplayPort Interoperability Guideline v1.1a
* 1.2: DisplayPort 1.2
*
* 1.2 formally includes both eDP and DPI definitions.
*/
#define DP_AUX_I2C_WRITE 0x0
#define DP_AUX_I2C_READ 0x1
#define DP_AUX_I2C_STATUS 0x2
#define DP_AUX_I2C_MOT 0x4
#define DP_AUX_NATIVE_WRITE 0x8
#define DP_AUX_NATIVE_READ 0x9
#define DP_AUX_NATIVE_REPLY_ACK (0x0 << 0)
#define DP_AUX_NATIVE_REPLY_NACK (0x1 << 0)
#define DP_AUX_NATIVE_REPLY_DEFER (0x2 << 0)
#define DP_AUX_NATIVE_REPLY_MASK (0x3 << 0)
#define DP_AUX_I2C_REPLY_ACK (0x0 << 2)
#define DP_AUX_I2C_REPLY_NACK (0x1 << 2)
#define DP_AUX_I2C_REPLY_DEFER (0x2 << 2)
#define DP_AUX_I2C_REPLY_MASK (0x3 << 2)
/* AUX CH addresses */
/* DPCD */
#define DP_DPCD_REV 0x000
#define DP_MAX_LINK_RATE 0x001
#define DP_MAX_LANE_COUNT 0x002
# define DP_MAX_LANE_COUNT_MASK 0x1f
# define DP_TPS3_SUPPORTED (1 << 6) /* 1.2 */
# define DP_ENHANCED_FRAME_CAP (1 << 7)
#define DP_MAX_DOWNSPREAD 0x003
# define DP_NO_AUX_HANDSHAKE_LINK_TRAINING (1 << 6)
#define DP_NORP 0x004
#define DP_DOWNSTREAMPORT_PRESENT 0x005
# define DP_DWN_STRM_PORT_PRESENT (1 << 0)
# define DP_DWN_STRM_PORT_TYPE_MASK 0x06
# define DP_DWN_STRM_PORT_TYPE_DP (0 << 1)
# define DP_DWN_STRM_PORT_TYPE_ANALOG (1 << 1)
# define DP_DWN_STRM_PORT_TYPE_TMDS (2 << 1)
# define DP_DWN_STRM_PORT_TYPE_OTHER (3 << 1)
# define DP_FORMAT_CONVERSION (1 << 3)
# define DP_DETAILED_CAP_INFO_AVAILABLE (1 << 4) /* DPI */
#define DP_MAIN_LINK_CHANNEL_CODING 0x006
#define DP_DOWN_STREAM_PORT_COUNT 0x007
# define DP_PORT_COUNT_MASK 0x0f
# define DP_MSA_TIMING_PAR_IGNORED (1 << 6) /* eDP */
# define DP_OUI_SUPPORT (1 << 7)
#define DP_I2C_SPEED_CAP 0x00c /* DPI */
# define DP_I2C_SPEED_1K 0x01
# define DP_I2C_SPEED_5K 0x02
# define DP_I2C_SPEED_10K 0x04
# define DP_I2C_SPEED_100K 0x08
# define DP_I2C_SPEED_400K 0x10
# define DP_I2C_SPEED_1M 0x20
#define DP_EDP_CONFIGURATION_CAP 0x00d /* XXX 1.2? */
#define DP_TRAINING_AUX_RD_INTERVAL 0x00e /* XXX 1.2? */
/* Multiple stream transport */
#define DP_MSTM_CAP 0x021 /* 1.2 */
# define DP_MST_CAP (1 << 0)
#define DP_PSR_SUPPORT 0x070 /* XXX 1.2? */
# define DP_PSR_IS_SUPPORTED 1
#define DP_PSR_CAPS 0x071 /* XXX 1.2? */
# define DP_PSR_NO_TRAIN_ON_EXIT 1
# define DP_PSR_SETUP_TIME_330 (0 << 1)
# define DP_PSR_SETUP_TIME_275 (1 << 1)
# define DP_PSR_SETUP_TIME_220 (2 << 1)
# define DP_PSR_SETUP_TIME_165 (3 << 1)
# define DP_PSR_SETUP_TIME_110 (4 << 1)
# define DP_PSR_SETUP_TIME_55 (5 << 1)
# define DP_PSR_SETUP_TIME_0 (6 << 1)
# define DP_PSR_SETUP_TIME_MASK (7 << 1)
# define DP_PSR_SETUP_TIME_SHIFT 1
/*
* 0x80-0x8f describe downstream port capabilities, but there are two layouts
* based on whether DP_DETAILED_CAP_INFO_AVAILABLE was set. If it was not,
* each port's descriptor is one byte wide. If it was set, each port's is
* four bytes wide, starting with the one byte from the base info. As of
* DP interop v1.1a only VGA defines additional detail.
*/
/* offset 0 */
#define DP_DOWNSTREAM_PORT_0 0x80
# define DP_DS_PORT_TYPE_MASK (7 << 0)
# define DP_DS_PORT_TYPE_DP 0
# define DP_DS_PORT_TYPE_VGA 1
# define DP_DS_PORT_TYPE_DVI 2
# define DP_DS_PORT_TYPE_HDMI 3
# define DP_DS_PORT_TYPE_NON_EDID 4
# define DP_DS_PORT_HPD (1 << 3)
/* offset 1 for VGA is maximum megapixels per second / 8 */
/* offset 2 */
# define DP_DS_VGA_MAX_BPC_MASK (3 << 0)
# define DP_DS_VGA_8BPC 0
# define DP_DS_VGA_10BPC 1
# define DP_DS_VGA_12BPC 2
# define DP_DS_VGA_16BPC 3
/* link configuration */
#define DP_LINK_BW_SET 0x100
# define DP_LINK_BW_1_62 0x06
# define DP_LINK_BW_2_7 0x0a
# define DP_LINK_BW_5_4 0x14 /* 1.2 */
#define DP_LANE_COUNT_SET 0x101
# define DP_LANE_COUNT_MASK 0x0f
# define DP_LANE_COUNT_ENHANCED_FRAME_EN (1 << 7)
#define DP_TRAINING_PATTERN_SET 0x102
# define DP_TRAINING_PATTERN_DISABLE 0
# define DP_TRAINING_PATTERN_1 1
# define DP_TRAINING_PATTERN_2 2
# define DP_TRAINING_PATTERN_3 3 /* 1.2 */
# define DP_TRAINING_PATTERN_MASK 0x3
# define DP_LINK_QUAL_PATTERN_DISABLE (0 << 2)
# define DP_LINK_QUAL_PATTERN_D10_2 (1 << 2)
# define DP_LINK_QUAL_PATTERN_ERROR_RATE (2 << 2)
# define DP_LINK_QUAL_PATTERN_PRBS7 (3 << 2)
# define DP_LINK_QUAL_PATTERN_MASK (3 << 2)
# define DP_RECOVERED_CLOCK_OUT_EN (1 << 4)
# define DP_LINK_SCRAMBLING_DISABLE (1 << 5)
# define DP_SYMBOL_ERROR_COUNT_BOTH (0 << 6)
# define DP_SYMBOL_ERROR_COUNT_DISPARITY (1 << 6)
# define DP_SYMBOL_ERROR_COUNT_SYMBOL (2 << 6)
# define DP_SYMBOL_ERROR_COUNT_MASK (3 << 6)
#define DP_TRAINING_LANE0_SET 0x103
#define DP_TRAINING_LANE1_SET 0x104
#define DP_TRAINING_LANE2_SET 0x105
#define DP_TRAINING_LANE3_SET 0x106
# define DP_TRAIN_VOLTAGE_SWING_MASK 0x3
# define DP_TRAIN_VOLTAGE_SWING_SHIFT 0
# define DP_TRAIN_MAX_SWING_REACHED (1 << 2)
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
# define DP_TRAIN_VOLTAGE_SWING_600 (1 << 0)
# define DP_TRAIN_VOLTAGE_SWING_800 (2 << 0)
# define DP_TRAIN_VOLTAGE_SWING_1200 (3 << 0)
# define DP_TRAIN_PRE_EMPHASIS_MASK (3 << 3)
# define DP_TRAIN_PRE_EMPHASIS_0 (0 << 3)
# define DP_TRAIN_PRE_EMPHASIS_3_5 (1 << 3)
# define DP_TRAIN_PRE_EMPHASIS_6 (2 << 3)
# define DP_TRAIN_PRE_EMPHASIS_9_5 (3 << 3)
# define DP_TRAIN_PRE_EMPHASIS_SHIFT 3
# define DP_TRAIN_MAX_PRE_EMPHASIS_REACHED (1 << 5)
#define DP_DOWNSPREAD_CTRL 0x107
# define DP_SPREAD_AMP_0_5 (1 << 4)
# define DP_MSA_TIMING_PAR_IGNORE_EN (1 << 7) /* eDP */
#define DP_MAIN_LINK_CHANNEL_CODING_SET 0x108
# define DP_SET_ANSI_8B10B (1 << 0)
#define DP_I2C_SPEED_CONTROL_STATUS 0x109 /* DPI */
/* bitmask as for DP_I2C_SPEED_CAP */
#define DP_EDP_CONFIGURATION_SET 0x10a /* XXX 1.2? */
#define DP_MSTM_CTRL 0x111 /* 1.2 */
# define DP_MST_EN (1 << 0)
# define DP_UP_REQ_EN (1 << 1)
# define DP_UPSTREAM_IS_SRC (1 << 2)
#define DP_PSR_EN_CFG 0x170 /* XXX 1.2? */
# define DP_PSR_ENABLE (1 << 0)
# define DP_PSR_MAIN_LINK_ACTIVE (1 << 1)
# define DP_PSR_CRC_VERIFICATION (1 << 2)
# define DP_PSR_FRAME_CAPTURE (1 << 3)
#define DP_SINK_COUNT 0x200
/* prior to 1.2 bit 7 was reserved mbz */
# define DP_GET_SINK_COUNT(x) ((((x) & 0x80) >> 1) | ((x) & 0x3f))
# define DP_SINK_CP_READY (1 << 6)
#define DP_DEVICE_SERVICE_IRQ_VECTOR 0x201
# define DP_REMOTE_CONTROL_COMMAND_PENDING (1 << 0)
# define DP_AUTOMATED_TEST_REQUEST (1 << 1)
# define DP_CP_IRQ (1 << 2)
# define DP_SINK_SPECIFIC_IRQ (1 << 6)
#define DP_LANE0_1_STATUS 0x202
#define DP_LANE2_3_STATUS 0x203
# define DP_LANE_CR_DONE (1 << 0)
# define DP_LANE_CHANNEL_EQ_DONE (1 << 1)
# define DP_LANE_SYMBOL_LOCKED (1 << 2)
#define DP_CHANNEL_EQ_BITS (DP_LANE_CR_DONE | \
DP_LANE_CHANNEL_EQ_DONE | \
DP_LANE_SYMBOL_LOCKED)
#define DP_LANE_ALIGN_STATUS_UPDATED 0x204
#define DP_INTERLANE_ALIGN_DONE (1 << 0)
#define DP_DOWNSTREAM_PORT_STATUS_CHANGED (1 << 6)
#define DP_LINK_STATUS_UPDATED (1 << 7)
#define DP_SINK_STATUS 0x205
#define DP_RECEIVE_PORT_0_STATUS (1 << 0)
#define DP_RECEIVE_PORT_1_STATUS (1 << 1)
#define DP_ADJUST_REQUEST_LANE0_1 0x206
#define DP_ADJUST_REQUEST_LANE2_3 0x207
# define DP_ADJUST_VOLTAGE_SWING_LANE0_MASK 0x03
# define DP_ADJUST_VOLTAGE_SWING_LANE0_SHIFT 0
# define DP_ADJUST_PRE_EMPHASIS_LANE0_MASK 0x0c
# define DP_ADJUST_PRE_EMPHASIS_LANE0_SHIFT 2
# define DP_ADJUST_VOLTAGE_SWING_LANE1_MASK 0x30
# define DP_ADJUST_VOLTAGE_SWING_LANE1_SHIFT 4
# define DP_ADJUST_PRE_EMPHASIS_LANE1_MASK 0xc0
# define DP_ADJUST_PRE_EMPHASIS_LANE1_SHIFT 6
#define DP_TEST_REQUEST 0x218
# define DP_TEST_LINK_TRAINING (1 << 0)
# define DP_TEST_LINK_VIDEO_PATTERN (1 << 1)
# define DP_TEST_LINK_EDID_READ (1 << 2)
# define DP_TEST_LINK_PHY_TEST_PATTERN (1 << 3) /* DPCD >= 1.1 */
# define DP_TEST_LINK_FAUX_PATTERN (1 << 4) /* DPCD >= 1.2 */
#define DP_TEST_LINK_RATE 0x219
# define DP_LINK_RATE_162 (0x6)
# define DP_LINK_RATE_27 (0xa)
#define DP_TEST_LANE_COUNT 0x220
#define DP_TEST_PATTERN 0x221
#define DP_TEST_RESPONSE 0x260
# define DP_TEST_ACK (1 << 0)
# define DP_TEST_NAK (1 << 1)
# define DP_TEST_EDID_CHECKSUM_WRITE (1 << 2)
#define DP_SOURCE_OUI 0x300
#define DP_SINK_OUI 0x400
#define DP_BRANCH_OUI 0x500
#define DP_SET_POWER 0x600
# define DP_SET_POWER_D0 0x1
# define DP_SET_POWER_D3 0x2
#define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */
# define DP_PSR_LINK_CRC_ERROR (1 << 0)
# define DP_PSR_RFB_STORAGE_ERROR (1 << 1)
#define DP_PSR_ESI 0x2007 /* XXX 1.2? */
# define DP_PSR_CAPS_CHANGE (1 << 0)
#define DP_PSR_STATUS 0x2008 /* XXX 1.2? */
# define DP_PSR_SINK_INACTIVE 0
# define DP_PSR_SINK_ACTIVE_SRC_SYNCED 1
# define DP_PSR_SINK_ACTIVE_RFB 2
# define DP_PSR_SINK_ACTIVE_SINK_SYNCED 3
# define DP_PSR_SINK_ACTIVE_RESYNC 4
# define DP_PSR_SINK_INTERNAL_ERROR 7
# define DP_PSR_SINK_STATE_MASK 0x07
#define MODE_I2C_START 1
#define MODE_I2C_WRITE 2
#define MODE_I2C_READ 4
#define MODE_I2C_STOP 8
/**
* struct i2c_algo_dp_aux_data - driver interface structure for i2c over dp
* aux algorithm
* @running: set by the algo indicating whether an i2c is ongoing or whether
* the i2c bus is quiescent
* @address: i2c target address for the currently ongoing transfer
* @aux_ch: driver callback to transfer a single byte of the i2c payload
*/
struct i2c_algo_dp_aux_data {
bool running;
u16 address;
int (*aux_ch) (struct i2c_adapter *adapter,
int mode, uint8_t write_byte,
uint8_t *read_byte);
};
int
i2c_dp_aux_add_bus(struct i2c_adapter *adapter);
#define DP_LINK_STATUS_SIZE 6
bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
int lane_count);
bool drm_dp_clock_recovery_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
int lane_count);
u8 drm_dp_get_adjust_request_voltage(const u8 link_status[DP_LINK_STATUS_SIZE],
int lane);
u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SIZE],
int lane);
#define DP_RECEIVER_CAP_SIZE 0xf
#define EDP_PSR_RECEIVER_CAP_SIZE 2
void drm_dp_link_train_clock_recovery_delay(const u8 dpcd[DP_RECEIVER_CAP_SIZE]);
void drm_dp_link_train_channel_eq_delay(const u8 dpcd[DP_RECEIVER_CAP_SIZE]);
u8 drm_dp_link_rate_to_bw_code(int link_rate);
int drm_dp_bw_code_to_link_rate(u8 link_bw);
struct edp_sdp_header {
u8 HB0; /* Secondary Data Packet ID */
u8 HB1; /* Secondary Data Packet Type */
u8 HB2; /* 7:5 reserved, 4:0 revision number */
u8 HB3; /* 7:5 reserved, 4:0 number of valid data bytes */
} __packed;
#define EDP_SDP_HEADER_REVISION_MASK 0x1F
#define EDP_SDP_HEADER_VALID_PAYLOAD_BYTES 0x1F
struct edp_vsc_psr {
struct edp_sdp_header sdp_header;
u8 DB0; /* Stereo Interface */
u8 DB1; /* 0 - PSR State; 1 - Update RFB; 2 - CRC Valid */
u8 DB2; /* CRC value bits 7:0 of the R or Cr component */
u8 DB3; /* CRC value bits 15:8 of the R or Cr component */
u8 DB4; /* CRC value bits 7:0 of the G or Y component */
u8 DB5; /* CRC value bits 15:8 of the G or Y component */
u8 DB6; /* CRC value bits 7:0 of the B or Cb component */
u8 DB7; /* CRC value bits 15:8 of the B or Cb component */
u8 DB8_31[24]; /* Reserved */
} __packed;
#define EDP_VSC_PSR_STATE_ACTIVE (1<<0)
#define EDP_VSC_PSR_UPDATE_RFB (1<<1)
#define EDP_VSC_PSR_CRC_VALUES_VALID (1<<2)
static inline int
drm_dp_max_link_rate(const u8 dpcd[DP_RECEIVER_CAP_SIZE])
{
return drm_dp_bw_code_to_link_rate(dpcd[DP_MAX_LINK_RATE]);
}
static inline u8
drm_dp_max_lane_count(const u8 dpcd[DP_RECEIVER_CAP_SIZE])
{
return dpcd[DP_MAX_LANE_COUNT] & DP_MAX_LANE_COUNT_MASK;
}
static inline bool
drm_dp_enhanced_frame_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE])
{
return dpcd[DP_DPCD_REV] >= 0x11 &&
(dpcd[DP_MAX_LANE_COUNT] & DP_ENHANCED_FRAME_CAP);
}
#endif /* _DRM_DP_HELPER_H_ */