369 строки
10 KiB
C
369 строки
10 KiB
C
/*
|
|
* Marvell 10G 88x3310 PHY driver
|
|
*
|
|
* Based upon the ID registers, this PHY appears to be a mixture of IPs
|
|
* from two different companies.
|
|
*
|
|
* There appears to be several different data paths through the PHY which
|
|
* are automatically managed by the PHY. The following has been determined
|
|
* via observation and experimentation:
|
|
*
|
|
* SGMII PHYXS -- BASE-T PCS -- 10G PMA -- AN -- Copper (for <= 1G)
|
|
* 10GBASE-KR PHYXS -- BASE-T PCS -- 10G PMA -- AN -- Copper (for 10G)
|
|
* 10GBASE-KR PHYXS -- BASE-R PCS -- Fiber
|
|
*
|
|
* If both the fiber and copper ports are connected, the first to gain
|
|
* link takes priority and the other port is completely locked out.
|
|
*/
|
|
#include <linux/phy.h>
|
|
|
|
enum {
|
|
MV_PCS_BASE_T = 0x0000,
|
|
MV_PCS_BASE_R = 0x1000,
|
|
MV_PCS_1000BASEX = 0x2000,
|
|
|
|
/* These registers appear at 0x800X and 0xa00X - the 0xa00X control
|
|
* registers appear to set themselves to the 0x800X when AN is
|
|
* restarted, but status registers appear readable from either.
|
|
*/
|
|
MV_AN_CTRL1000 = 0x8000, /* 1000base-T control register */
|
|
MV_AN_STAT1000 = 0x8001, /* 1000base-T status register */
|
|
|
|
/* This register appears to reflect the copper status */
|
|
MV_AN_RESULT = 0xa016,
|
|
MV_AN_RESULT_SPD_10 = BIT(12),
|
|
MV_AN_RESULT_SPD_100 = BIT(13),
|
|
MV_AN_RESULT_SPD_1000 = BIT(14),
|
|
MV_AN_RESULT_SPD_10000 = BIT(15),
|
|
};
|
|
|
|
static int mv3310_modify(struct phy_device *phydev, int devad, u16 reg,
|
|
u16 mask, u16 bits)
|
|
{
|
|
int old, val, ret;
|
|
|
|
old = phy_read_mmd(phydev, devad, reg);
|
|
if (old < 0)
|
|
return old;
|
|
|
|
val = (old & ~mask) | (bits & mask);
|
|
if (val == old)
|
|
return 0;
|
|
|
|
ret = phy_write_mmd(phydev, devad, reg, val);
|
|
|
|
return ret < 0 ? ret : 1;
|
|
}
|
|
|
|
static int mv3310_probe(struct phy_device *phydev)
|
|
{
|
|
u32 mmd_mask = MDIO_DEVS_PMAPMD | MDIO_DEVS_AN;
|
|
|
|
if (!phydev->is_c45 ||
|
|
(phydev->c45_ids.devices_in_package & mmd_mask) != mmd_mask)
|
|
return -ENODEV;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Resetting the MV88X3310 causes it to become non-responsive. Avoid
|
|
* setting the reset bit(s).
|
|
*/
|
|
static int mv3310_soft_reset(struct phy_device *phydev)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static int mv3310_config_init(struct phy_device *phydev)
|
|
{
|
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0, };
|
|
u32 mask;
|
|
int val;
|
|
|
|
/* Check that the PHY interface type is compatible */
|
|
if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
|
|
phydev->interface != PHY_INTERFACE_MODE_XGMII &&
|
|
phydev->interface != PHY_INTERFACE_MODE_XAUI &&
|
|
phydev->interface != PHY_INTERFACE_MODE_RXAUI &&
|
|
phydev->interface != PHY_INTERFACE_MODE_10GKR)
|
|
return -ENODEV;
|
|
|
|
__set_bit(ETHTOOL_LINK_MODE_Pause_BIT, supported);
|
|
__set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, supported);
|
|
|
|
if (phydev->c45_ids.devices_in_package & MDIO_DEVS_AN) {
|
|
val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_STAT1);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & MDIO_AN_STAT1_ABLE)
|
|
__set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, supported);
|
|
}
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_STAT2);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
/* Ethtool does not support the WAN mode bits */
|
|
if (val & (MDIO_PMA_STAT2_10GBSR | MDIO_PMA_STAT2_10GBLR |
|
|
MDIO_PMA_STAT2_10GBER | MDIO_PMA_STAT2_10GBLX4 |
|
|
MDIO_PMA_STAT2_10GBSW | MDIO_PMA_STAT2_10GBLW |
|
|
MDIO_PMA_STAT2_10GBEW))
|
|
__set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, supported);
|
|
if (val & MDIO_PMA_STAT2_10GBSR)
|
|
__set_bit(ETHTOOL_LINK_MODE_10000baseSR_Full_BIT, supported);
|
|
if (val & MDIO_PMA_STAT2_10GBLR)
|
|
__set_bit(ETHTOOL_LINK_MODE_10000baseLR_Full_BIT, supported);
|
|
if (val & MDIO_PMA_STAT2_10GBER)
|
|
__set_bit(ETHTOOL_LINK_MODE_10000baseER_Full_BIT, supported);
|
|
|
|
if (val & MDIO_PMA_STAT2_EXTABLE) {
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_EXTABLE);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & (MDIO_PMA_EXTABLE_10GBT | MDIO_PMA_EXTABLE_1000BT |
|
|
MDIO_PMA_EXTABLE_100BTX | MDIO_PMA_EXTABLE_10BT))
|
|
__set_bit(ETHTOOL_LINK_MODE_TP_BIT, supported);
|
|
if (val & MDIO_PMA_EXTABLE_10GBLRM)
|
|
__set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, supported);
|
|
if (val & (MDIO_PMA_EXTABLE_10GBKX4 | MDIO_PMA_EXTABLE_10GBKR |
|
|
MDIO_PMA_EXTABLE_1000BKX))
|
|
__set_bit(ETHTOOL_LINK_MODE_Backplane_BIT, supported);
|
|
if (val & MDIO_PMA_EXTABLE_10GBLRM)
|
|
__set_bit(ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT,
|
|
supported);
|
|
if (val & MDIO_PMA_EXTABLE_10GBT)
|
|
__set_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
|
|
supported);
|
|
if (val & MDIO_PMA_EXTABLE_10GBKX4)
|
|
__set_bit(ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT,
|
|
supported);
|
|
if (val & MDIO_PMA_EXTABLE_10GBKR)
|
|
__set_bit(ETHTOOL_LINK_MODE_10000baseKR_Full_BIT,
|
|
supported);
|
|
if (val & MDIO_PMA_EXTABLE_1000BT)
|
|
__set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
|
|
supported);
|
|
if (val & MDIO_PMA_EXTABLE_1000BKX)
|
|
__set_bit(ETHTOOL_LINK_MODE_1000baseKX_Full_BIT,
|
|
supported);
|
|
if (val & MDIO_PMA_EXTABLE_100BTX)
|
|
__set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
|
|
supported);
|
|
if (val & MDIO_PMA_EXTABLE_10BT)
|
|
__set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT,
|
|
supported);
|
|
}
|
|
|
|
if (!ethtool_convert_link_mode_to_legacy_u32(&mask, supported))
|
|
dev_warn(&phydev->mdio.dev,
|
|
"PHY supports (%*pb) more modes than phylib supports, some modes not supported.\n",
|
|
__ETHTOOL_LINK_MODE_MASK_NBITS, supported);
|
|
|
|
phydev->supported &= mask;
|
|
phydev->advertising &= phydev->supported;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv3310_config_aneg(struct phy_device *phydev)
|
|
{
|
|
bool changed = false;
|
|
u32 advertising;
|
|
int ret;
|
|
|
|
if (phydev->autoneg == AUTONEG_DISABLE) {
|
|
ret = genphy_c45_pma_setup_forced(phydev);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return genphy_c45_an_disable_aneg(phydev);
|
|
}
|
|
|
|
phydev->advertising &= phydev->supported;
|
|
advertising = phydev->advertising;
|
|
|
|
ret = mv3310_modify(phydev, MDIO_MMD_AN, MDIO_AN_ADVERTISE,
|
|
ADVERTISE_ALL | ADVERTISE_100BASE4 |
|
|
ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM,
|
|
ethtool_adv_to_mii_adv_t(advertising));
|
|
if (ret < 0)
|
|
return ret;
|
|
if (ret > 0)
|
|
changed = true;
|
|
|
|
ret = mv3310_modify(phydev, MDIO_MMD_AN, MV_AN_CTRL1000,
|
|
ADVERTISE_1000FULL | ADVERTISE_1000HALF,
|
|
ethtool_adv_to_mii_ctrl1000_t(advertising));
|
|
if (ret < 0)
|
|
return ret;
|
|
if (ret > 0)
|
|
changed = true;
|
|
|
|
/* 10G control register */
|
|
ret = mv3310_modify(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
|
|
MDIO_AN_10GBT_CTRL_ADV10G,
|
|
advertising & ADVERTISED_10000baseT_Full ?
|
|
MDIO_AN_10GBT_CTRL_ADV10G : 0);
|
|
if (ret < 0)
|
|
return ret;
|
|
if (ret > 0)
|
|
changed = true;
|
|
|
|
if (changed)
|
|
ret = genphy_c45_restart_aneg(phydev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int mv3310_aneg_done(struct phy_device *phydev)
|
|
{
|
|
int val;
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & MDIO_STAT1_LSTATUS)
|
|
return 1;
|
|
|
|
return genphy_c45_aneg_done(phydev);
|
|
}
|
|
|
|
/* 10GBASE-ER,LR,LRM,SR do not support autonegotiation. */
|
|
static int mv3310_read_10gbr_status(struct phy_device *phydev)
|
|
{
|
|
phydev->link = 1;
|
|
phydev->speed = SPEED_10000;
|
|
phydev->duplex = DUPLEX_FULL;
|
|
|
|
if (phydev->interface == PHY_INTERFACE_MODE_SGMII)
|
|
phydev->interface = PHY_INTERFACE_MODE_10GKR;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv3310_read_status(struct phy_device *phydev)
|
|
{
|
|
u32 mmd_mask = phydev->c45_ids.devices_in_package;
|
|
int val;
|
|
|
|
/* The vendor devads do not report link status. Avoid the PHYXS
|
|
* instance as there are three, and its status depends on the MAC
|
|
* being appropriately configured for the negotiated speed.
|
|
*/
|
|
mmd_mask &= ~(BIT(MDIO_MMD_VEND1) | BIT(MDIO_MMD_VEND2) |
|
|
BIT(MDIO_MMD_PHYXS));
|
|
|
|
phydev->speed = SPEED_UNKNOWN;
|
|
phydev->duplex = DUPLEX_UNKNOWN;
|
|
phydev->lp_advertising = 0;
|
|
phydev->link = 0;
|
|
phydev->pause = 0;
|
|
phydev->asym_pause = 0;
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & MDIO_STAT1_LSTATUS)
|
|
return mv3310_read_10gbr_status(phydev);
|
|
|
|
val = genphy_c45_read_link(phydev, mmd_mask);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
phydev->link = val > 0 ? 1 : 0;
|
|
|
|
val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_STAT1);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & MDIO_AN_STAT1_COMPLETE) {
|
|
val = genphy_c45_read_lpa(phydev);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
/* Read the link partner's 1G advertisment */
|
|
val = phy_read_mmd(phydev, MDIO_MMD_AN, MV_AN_STAT1000);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
phydev->lp_advertising |= mii_stat1000_to_ethtool_lpa_t(val);
|
|
|
|
if (phydev->autoneg == AUTONEG_ENABLE) {
|
|
val = phy_read_mmd(phydev, MDIO_MMD_AN, MV_AN_RESULT);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
if (val & MV_AN_RESULT_SPD_10000)
|
|
phydev->speed = SPEED_10000;
|
|
else if (val & MV_AN_RESULT_SPD_1000)
|
|
phydev->speed = SPEED_1000;
|
|
else if (val & MV_AN_RESULT_SPD_100)
|
|
phydev->speed = SPEED_100;
|
|
else if (val & MV_AN_RESULT_SPD_10)
|
|
phydev->speed = SPEED_10;
|
|
|
|
phydev->duplex = DUPLEX_FULL;
|
|
}
|
|
}
|
|
|
|
if (phydev->autoneg != AUTONEG_ENABLE) {
|
|
val = genphy_c45_read_pma(phydev);
|
|
if (val < 0)
|
|
return val;
|
|
}
|
|
|
|
if ((phydev->interface == PHY_INTERFACE_MODE_SGMII ||
|
|
phydev->interface == PHY_INTERFACE_MODE_10GKR) && phydev->link) {
|
|
/* The PHY automatically switches its serdes interface (and
|
|
* active PHYXS instance) between Cisco SGMII and 10GBase-KR
|
|
* modes according to the speed. Florian suggests setting
|
|
* phydev->interface to communicate this to the MAC. Only do
|
|
* this if we are already in either SGMII or 10GBase-KR mode.
|
|
*/
|
|
if (phydev->speed == SPEED_10000)
|
|
phydev->interface = PHY_INTERFACE_MODE_10GKR;
|
|
else if (phydev->speed >= SPEED_10 &&
|
|
phydev->speed < SPEED_10000)
|
|
phydev->interface = PHY_INTERFACE_MODE_SGMII;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct phy_driver mv3310_drivers[] = {
|
|
{
|
|
.phy_id = 0x002b09aa,
|
|
.phy_id_mask = 0xffffffff,
|
|
.name = "mv88x3310",
|
|
.features = SUPPORTED_10baseT_Full |
|
|
SUPPORTED_100baseT_Full |
|
|
SUPPORTED_1000baseT_Full |
|
|
SUPPORTED_Autoneg |
|
|
SUPPORTED_TP |
|
|
SUPPORTED_FIBRE |
|
|
SUPPORTED_10000baseT_Full |
|
|
SUPPORTED_Backplane,
|
|
.probe = mv3310_probe,
|
|
.soft_reset = mv3310_soft_reset,
|
|
.config_init = mv3310_config_init,
|
|
.config_aneg = mv3310_config_aneg,
|
|
.aneg_done = mv3310_aneg_done,
|
|
.read_status = mv3310_read_status,
|
|
},
|
|
};
|
|
|
|
module_phy_driver(mv3310_drivers);
|
|
|
|
static struct mdio_device_id __maybe_unused mv3310_tbl[] = {
|
|
{ 0x002b09aa, 0xffffffff },
|
|
{ },
|
|
};
|
|
MODULE_DEVICE_TABLE(mdio, mv3310_tbl);
|
|
MODULE_DESCRIPTION("Marvell Alaska X 10Gigabit Ethernet PHY driver (MV88X3310)");
|
|
MODULE_LICENSE("GPL");
|