168 строки
4.7 KiB
Plaintext
168 строки
4.7 KiB
Plaintext
config MAC80211
|
|
tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
|
|
select CRYPTO
|
|
select CRYPTO_ECB
|
|
select CRYPTO_ARC4
|
|
select CRYPTO_AES
|
|
select CRC32
|
|
select WIRELESS_EXT
|
|
select CFG80211
|
|
select NET_SCH_FIFO
|
|
---help---
|
|
This option enables the hardware independent IEEE 802.11
|
|
networking stack.
|
|
|
|
menu "Rate control algorithm selection"
|
|
depends on MAC80211 != n
|
|
|
|
choice
|
|
prompt "Default rate control algorithm"
|
|
default MAC80211_RC_DEFAULT_PID
|
|
---help---
|
|
This option selects the default rate control algorithm
|
|
mac80211 will use. Note that this default can still be
|
|
overriden through the ieee80211_default_rc_algo module
|
|
parameter if different algorithms are available.
|
|
|
|
config MAC80211_RC_DEFAULT_PID
|
|
bool "PID controller based rate control algorithm"
|
|
select MAC80211_RC_PID
|
|
---help---
|
|
Select the PID controller based rate control as the
|
|
default rate control algorithm. You should choose
|
|
this unless you know what you are doing.
|
|
|
|
config MAC80211_RC_DEFAULT_NONE
|
|
bool "No default algorithm"
|
|
depends on EMBEDDED
|
|
help
|
|
Selecting this option will select no default algorithm
|
|
and allow you to not build any. Do not choose this
|
|
option unless you know your driver comes with another
|
|
suitable algorithm.
|
|
endchoice
|
|
|
|
comment "Selecting 'y' for an algorithm will"
|
|
comment "build the algorithm into mac80211."
|
|
|
|
config MAC80211_RC_DEFAULT
|
|
string
|
|
default "pid" if MAC80211_RC_DEFAULT_PID
|
|
default ""
|
|
|
|
config MAC80211_RC_PID
|
|
tristate "PID controller based rate control algorithm"
|
|
---help---
|
|
This option enables a TX rate control algorithm for
|
|
mac80211 that uses a PID controller to select the TX
|
|
rate.
|
|
|
|
Say Y or M unless you're sure you want to use a
|
|
different rate control algorithm.
|
|
|
|
endmenu
|
|
|
|
config MAC80211_MESH
|
|
bool "Enable mac80211 mesh networking (pre-802.11s) support"
|
|
depends on MAC80211 && EXPERIMENTAL
|
|
---help---
|
|
This options enables support of Draft 802.11s mesh networking.
|
|
The implementation is based on Draft 1.08 of the Mesh Networking
|
|
amendment. For more information visit http://o11s.org/.
|
|
|
|
|
|
config MAC80211_LEDS
|
|
bool "Enable LED triggers"
|
|
depends on MAC80211
|
|
select NEW_LEDS
|
|
select LEDS_TRIGGERS
|
|
---help---
|
|
This option enables a few LED triggers for different
|
|
packet receive/transmit events.
|
|
|
|
config MAC80211_DEBUGFS
|
|
bool "Export mac80211 internals in DebugFS"
|
|
depends on MAC80211 && DEBUG_FS
|
|
---help---
|
|
Select this to see extensive information about
|
|
the internal state of mac80211 in debugfs.
|
|
|
|
Say N unless you know you need this.
|
|
|
|
config MAC80211_DEBUG_PACKET_ALIGNMENT
|
|
bool "Enable packet alignment debugging"
|
|
depends on MAC80211
|
|
help
|
|
This option is recommended for driver authors and strongly
|
|
discouraged for everybody else, it will trigger a warning
|
|
when a driver hands mac80211 a buffer that is aligned in
|
|
a way that will cause problems with the IP stack on some
|
|
architectures.
|
|
|
|
Say N unless you're writing a mac80211 based driver.
|
|
|
|
config MAC80211_DEBUG
|
|
bool "Enable debugging output"
|
|
depends on MAC80211
|
|
---help---
|
|
This option will enable debug tracing output for the
|
|
ieee80211 network stack.
|
|
|
|
If you are not trying to debug or develop the ieee80211
|
|
subsystem, you most likely want to say N here.
|
|
|
|
config MAC80211_HT_DEBUG
|
|
bool "Enable HT debugging output"
|
|
depends on MAC80211_DEBUG
|
|
---help---
|
|
This option enables 802.11n High Throughput features
|
|
debug tracing output.
|
|
|
|
If you are not trying to debug of develop the ieee80211
|
|
subsystem, you most likely want to say N here.
|
|
|
|
config MAC80211_VERBOSE_DEBUG
|
|
bool "Verbose debugging output"
|
|
depends on MAC80211_DEBUG
|
|
|
|
config MAC80211_LOWTX_FRAME_DUMP
|
|
bool "Debug frame dumping"
|
|
depends on MAC80211_DEBUG
|
|
---help---
|
|
Selecting this option will cause the stack to
|
|
print a message for each frame that is handed
|
|
to the lowlevel driver for transmission. This
|
|
message includes all MAC addresses and the
|
|
frame control field.
|
|
|
|
If unsure, say N and insert the debugging code
|
|
you require into the driver you are debugging.
|
|
|
|
config TKIP_DEBUG
|
|
bool "TKIP debugging"
|
|
depends on MAC80211_DEBUG
|
|
|
|
config MAC80211_DEBUG_COUNTERS
|
|
bool "Extra statistics for TX/RX debugging"
|
|
depends on MAC80211_DEBUG
|
|
|
|
config MAC80211_IBSS_DEBUG
|
|
bool "Support for IBSS testing"
|
|
depends on MAC80211_DEBUG
|
|
---help---
|
|
Say Y here if you intend to debug the IBSS code.
|
|
|
|
config MAC80211_VERBOSE_PS_DEBUG
|
|
bool "Verbose powersave mode debugging"
|
|
depends on MAC80211_DEBUG
|
|
---help---
|
|
Say Y here to print out verbose powersave
|
|
mode debug messages.
|
|
|
|
config MAC80211_VERBOSE_MPL_DEBUG
|
|
bool "Verbose mesh peer link debugging"
|
|
depends on MAC80211_DEBUG && MAC80211_MESH
|
|
---help---
|
|
Say Y here to print out verbose mesh peer link
|
|
debug messages.
|