WSL2-Linux-Kernel/drivers/ide/cs5520.c

169 строки
4.7 KiB
C

/*
* IDE tuning and bus mastering support for the CS5510/CS5520
* chipsets
*
* The CS5510/CS5520 are slightly unusual devices. Unlike the
* typical IDE controllers they do bus mastering with the drive in
* PIO mode and smarter silicon.
*
* The practical upshot of this is that we must always tune the
* drive for the right PIO mode. We must also ignore all the blacklists
* and the drive bus mastering DMA information.
*
* *** This driver is strictly experimental ***
*
* (c) Copyright Red Hat Inc 2002
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2, or (at your option) any
* later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* For the avoidance of doubt the "preferred form" of this code is one which
* is in an open non patent encumbered format. Where cryptographic key signing
* forms part of the process of creating an executable the information
* including keys needed to generate an equivalently functional executable
* are deemed to be part of the source code.
*
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/dma-mapping.h>
#define DRV_NAME "cs5520"
struct pio_clocks
{
int address;
int assert;
int recovery;
};
static struct pio_clocks cs5520_pio_clocks[]={
{3, 6, 11},
{2, 5, 6},
{1, 4, 3},
{1, 3, 2},
{1, 2, 1}
};
static void cs5520_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
int controller = drive->dn > 1 ? 1 : 0;
const u8 pio = drive->pio_mode - XFER_PIO_0;
/* 8bit CAT/CRT - 8bit command timing for channel */
pci_write_config_byte(pdev, 0x62 + controller,
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
/* 0x64 - 16bit Primary, 0x68 - 16bit Secondary */
/* FIXME: should these use address ? */
/* Data read timing */
pci_write_config_byte(pdev, 0x64 + 4*controller + (drive->dn&1),
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
/* Write command timing */
pci_write_config_byte(pdev, 0x66 + 4*controller + (drive->dn&1),
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
}
static void cs5520_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
printk(KERN_ERR "cs55x0: bad ide timing.\n");
drive->pio_mode = XFER_PIO_0 + 0;
cs5520_set_pio_mode(hwif, drive);
}
static const struct ide_port_ops cs5520_port_ops = {
.set_pio_mode = cs5520_set_pio_mode,
.set_dma_mode = cs5520_set_dma_mode,
};
static const struct ide_port_info cyrix_chipset = {
.name = DRV_NAME,
.enablebits = { { 0x60, 0x01, 0x01 }, { 0x60, 0x02, 0x02 } },
.port_ops = &cs5520_port_ops,
.host_flags = IDE_HFLAG_ISA_PORTS | IDE_HFLAG_CS5520,
.pio_mask = ATA_PIO4,
};
/*
* The 5510/5520 are a bit weird. They don't quite set up the way
* the PCI helper layer expects so we must do much of the set up
* work longhand.
*/
static int cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
const struct ide_port_info *d = &cyrix_chipset;
struct ide_hw hw[2], *hws[] = { NULL, NULL };
ide_setup_pci_noise(dev, d);
/* We must not grab the entire device, it has 'ISA' space in its
* BARS too and we will freak out other bits of the kernel
*/
if (pci_enable_device_io(dev)) {
printk(KERN_WARNING "%s: Unable to enable 55x0.\n", d->name);
return -ENODEV;
}
pci_set_master(dev);
if (pci_set_dma_mask(dev, DMA_BIT_MASK(32))) {
printk(KERN_WARNING "%s: No suitable DMA available.\n",
d->name);
return -ENODEV;
}
/*
* Now the chipset is configured we can let the core
* do all the device setup for us
*/
ide_pci_setup_ports(dev, d, &hw[0], &hws[0]);
hw[0].irq = 14;
hw[1].irq = 15;
return ide_host_add(d, hws, 2, NULL);
}
static const struct pci_device_id cs5520_pci_tbl[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), 0 },
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, cs5520_pci_tbl);
static struct pci_driver cs5520_pci_driver = {
.name = "Cyrix_IDE",
.id_table = cs5520_pci_tbl,
.probe = cs5520_init_one,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init cs5520_ide_init(void)
{
return ide_pci_register_driver(&cs5520_pci_driver);
}
module_init(cs5520_ide_init);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("PCI driver module for Cyrix 5510/5520 IDE");
MODULE_LICENSE("GPL");