380 строки
11 KiB
C
380 строки
11 KiB
C
#ifndef _SMU_H
|
|
#define _SMU_H
|
|
|
|
/*
|
|
* Definitions for talking to the SMU chip in newer G5 PowerMacs
|
|
*/
|
|
|
|
#include <linux/config.h>
|
|
#include <linux/list.h>
|
|
|
|
/*
|
|
* Known SMU commands
|
|
*
|
|
* Most of what is below comes from looking at the Open Firmware driver,
|
|
* though this is still incomplete and could use better documentation here
|
|
* or there...
|
|
*/
|
|
|
|
|
|
/*
|
|
* Partition info commands
|
|
*
|
|
* I do not know what those are for at this point
|
|
*/
|
|
#define SMU_CMD_PARTITION_COMMAND 0x3e
|
|
|
|
|
|
/*
|
|
* Fan control
|
|
*
|
|
* This is a "mux" for fan control commands, first byte is the
|
|
* "sub" command.
|
|
*/
|
|
#define SMU_CMD_FAN_COMMAND 0x4a
|
|
|
|
|
|
/*
|
|
* Battery access
|
|
*
|
|
* Same command number as the PMU, could it be same syntax ?
|
|
*/
|
|
#define SMU_CMD_BATTERY_COMMAND 0x6f
|
|
#define SMU_CMD_GET_BATTERY_INFO 0x00
|
|
|
|
/*
|
|
* Real time clock control
|
|
*
|
|
* This is a "mux", first data byte contains the "sub" command.
|
|
* The "RTC" part of the SMU controls the date, time, powerup
|
|
* timer, but also a PRAM
|
|
*
|
|
* Dates are in BCD format on 7 bytes:
|
|
* [sec] [min] [hour] [weekday] [month day] [month] [year]
|
|
* with month being 1 based and year minus 100
|
|
*/
|
|
#define SMU_CMD_RTC_COMMAND 0x8e
|
|
#define SMU_CMD_RTC_SET_PWRUP_TIMER 0x00 /* i: 7 bytes date */
|
|
#define SMU_CMD_RTC_GET_PWRUP_TIMER 0x01 /* o: 7 bytes date */
|
|
#define SMU_CMD_RTC_STOP_PWRUP_TIMER 0x02
|
|
#define SMU_CMD_RTC_SET_PRAM_BYTE_ACC 0x20 /* i: 1 byte (address?) */
|
|
#define SMU_CMD_RTC_SET_PRAM_AUTOINC 0x21 /* i: 1 byte (data?) */
|
|
#define SMU_CMD_RTC_SET_PRAM_LO_BYTES 0x22 /* i: 10 bytes */
|
|
#define SMU_CMD_RTC_SET_PRAM_HI_BYTES 0x23 /* i: 10 bytes */
|
|
#define SMU_CMD_RTC_GET_PRAM_BYTE 0x28 /* i: 1 bytes (address?) */
|
|
#define SMU_CMD_RTC_GET_PRAM_LO_BYTES 0x29 /* o: 10 bytes */
|
|
#define SMU_CMD_RTC_GET_PRAM_HI_BYTES 0x2a /* o: 10 bytes */
|
|
#define SMU_CMD_RTC_SET_DATETIME 0x80 /* i: 7 bytes date */
|
|
#define SMU_CMD_RTC_GET_DATETIME 0x81 /* o: 7 bytes date */
|
|
|
|
/*
|
|
* i2c commands
|
|
*
|
|
* To issue an i2c command, first is to send a parameter block to the
|
|
* the SMU. This is a command of type 0x9a with 9 bytes of header
|
|
* eventually followed by data for a write:
|
|
*
|
|
* 0: bus number (from device-tree usually, SMU has lots of busses !)
|
|
* 1: transfer type/format (see below)
|
|
* 2: device address. For combined and combined4 type transfers, this
|
|
* is the "write" version of the address (bit 0x01 cleared)
|
|
* 3: subaddress length (0..3)
|
|
* 4: subaddress byte 0 (or only byte for subaddress length 1)
|
|
* 5: subaddress byte 1
|
|
* 6: subaddress byte 2
|
|
* 7: combined address (device address for combined mode data phase)
|
|
* 8: data length
|
|
*
|
|
* The transfer types are the same good old Apple ones it seems,
|
|
* that is:
|
|
* - 0x00: Simple transfer
|
|
* - 0x01: Subaddress transfer (addr write + data tx, no restart)
|
|
* - 0x02: Combined transfer (addr write + restart + data tx)
|
|
*
|
|
* This is then followed by actual data for a write.
|
|
*
|
|
* At this point, the OF driver seems to have a limitation on transfer
|
|
* sizes of 0xd bytes on reads and 0x5 bytes on writes. I do not know
|
|
* wether this is just an OF limit due to some temporary buffer size
|
|
* or if this is an SMU imposed limit. This driver has the same limitation
|
|
* for now as I use a 0x10 bytes temporary buffer as well
|
|
*
|
|
* Once that is completed, a response is expected from the SMU. This is
|
|
* obtained via a command of type 0x9a with a length of 1 byte containing
|
|
* 0 as the data byte. OF also fills the rest of the data buffer with 0xff's
|
|
* though I can't tell yet if this is actually necessary. Once this command
|
|
* is complete, at this point, all I can tell is what OF does. OF tests
|
|
* byte 0 of the reply:
|
|
* - on read, 0xfe or 0xfc : bus is busy, wait (see below) or nak ?
|
|
* - on read, 0x00 or 0x01 : reply is in buffer (after the byte 0)
|
|
* - on write, < 0 -> failure (immediate exit)
|
|
* - else, OF just exists (without error, weird)
|
|
*
|
|
* So on read, there is this wait-for-busy thing when getting a 0xfc or
|
|
* 0xfe result. OF does a loop of up to 64 retries, waiting 20ms and
|
|
* doing the above again until either the retries expire or the result
|
|
* is no longer 0xfe or 0xfc
|
|
*
|
|
* The Darwin I2C driver is less subtle though. On any non-success status
|
|
* from the response command, it waits 5ms and tries again up to 20 times,
|
|
* it doesn't differenciate between fatal errors or "busy" status.
|
|
*
|
|
* This driver provides an asynchronous paramblock based i2c command
|
|
* interface to be used either directly by low level code or by a higher
|
|
* level driver interfacing to the linux i2c layer. The current
|
|
* implementation of this relies on working timers & timer interrupts
|
|
* though, so be careful of calling context for now. This may be "fixed"
|
|
* in the future by adding a polling facility.
|
|
*/
|
|
#define SMU_CMD_I2C_COMMAND 0x9a
|
|
/* transfer types */
|
|
#define SMU_I2C_TRANSFER_SIMPLE 0x00
|
|
#define SMU_I2C_TRANSFER_STDSUB 0x01
|
|
#define SMU_I2C_TRANSFER_COMBINED 0x02
|
|
|
|
/*
|
|
* Power supply control
|
|
*
|
|
* The "sub" command is an ASCII string in the data, the
|
|
* data lenght is that of the string.
|
|
*
|
|
* The VSLEW command can be used to get or set the voltage slewing.
|
|
* - lenght 5 (only "VSLEW") : it returns "DONE" and 3 bytes of
|
|
* reply at data offset 6, 7 and 8.
|
|
* - lenght 8 ("VSLEWxyz") has 3 additional bytes appended, and is
|
|
* used to set the voltage slewing point. The SMU replies with "DONE"
|
|
* I yet have to figure out their exact meaning of those 3 bytes in
|
|
* both cases.
|
|
*
|
|
*/
|
|
#define SMU_CMD_POWER_COMMAND 0xaa
|
|
#define SMU_CMD_POWER_RESTART "RESTART"
|
|
#define SMU_CMD_POWER_SHUTDOWN "SHUTDOWN"
|
|
#define SMU_CMD_POWER_VOLTAGE_SLEW "VSLEW"
|
|
|
|
/* Misc commands
|
|
*
|
|
* This command seem to be a grab bag of various things
|
|
*/
|
|
#define SMU_CMD_MISC_df_COMMAND 0xdf
|
|
#define SMU_CMD_MISC_df_SET_DISPLAY_LIT 0x02 /* i: 1 byte */
|
|
#define SMU_CMD_MISC_df_NMI_OPTION 0x04
|
|
|
|
/*
|
|
* Version info commands
|
|
*
|
|
* I haven't quite tried to figure out how these work
|
|
*/
|
|
#define SMU_CMD_VERSION_COMMAND 0xea
|
|
|
|
|
|
/*
|
|
* Misc commands
|
|
*
|
|
* This command seem to be a grab bag of various things
|
|
*/
|
|
#define SMU_CMD_MISC_ee_COMMAND 0xee
|
|
#define SMU_CMD_MISC_ee_GET_DATABLOCK_REC 0x02
|
|
#define SMU_CMD_MISC_ee_LEDS_CTRL 0x04 /* i: 00 (00,01) [00] */
|
|
#define SMU_CMD_MISC_ee_GET_DATA 0x05 /* i: 00 , o: ?? */
|
|
|
|
|
|
|
|
/*
|
|
* - Kernel side interface -
|
|
*/
|
|
|
|
#ifdef __KERNEL__
|
|
|
|
/*
|
|
* Asynchronous SMU commands
|
|
*
|
|
* Fill up this structure and submit it via smu_queue_command(),
|
|
* and get notified by the optional done() callback, or because
|
|
* status becomes != 1
|
|
*/
|
|
|
|
struct smu_cmd;
|
|
|
|
struct smu_cmd
|
|
{
|
|
/* public */
|
|
u8 cmd; /* command */
|
|
int data_len; /* data len */
|
|
int reply_len; /* reply len */
|
|
void *data_buf; /* data buffer */
|
|
void *reply_buf; /* reply buffer */
|
|
int status; /* command status */
|
|
void (*done)(struct smu_cmd *cmd, void *misc);
|
|
void *misc;
|
|
|
|
/* private */
|
|
struct list_head link;
|
|
};
|
|
|
|
/*
|
|
* Queues an SMU command, all fields have to be initialized
|
|
*/
|
|
extern int smu_queue_cmd(struct smu_cmd *cmd);
|
|
|
|
/*
|
|
* Simple command wrapper. This structure embeds a small buffer
|
|
* to ease sending simple SMU commands from the stack
|
|
*/
|
|
struct smu_simple_cmd
|
|
{
|
|
struct smu_cmd cmd;
|
|
u8 buffer[16];
|
|
};
|
|
|
|
/*
|
|
* Queues a simple command. All fields will be initialized by that
|
|
* function
|
|
*/
|
|
extern int smu_queue_simple(struct smu_simple_cmd *scmd, u8 command,
|
|
unsigned int data_len,
|
|
void (*done)(struct smu_cmd *cmd, void *misc),
|
|
void *misc,
|
|
...);
|
|
|
|
/*
|
|
* Completion helper. Pass it to smu_queue_simple or as 'done'
|
|
* member to smu_queue_cmd, it will call complete() on the struct
|
|
* completion passed in the "misc" argument
|
|
*/
|
|
extern void smu_done_complete(struct smu_cmd *cmd, void *misc);
|
|
|
|
/*
|
|
* Synchronous helpers. Will spin-wait for completion of a command
|
|
*/
|
|
extern void smu_spinwait_cmd(struct smu_cmd *cmd);
|
|
|
|
static inline void smu_spinwait_simple(struct smu_simple_cmd *scmd)
|
|
{
|
|
smu_spinwait_cmd(&scmd->cmd);
|
|
}
|
|
|
|
/*
|
|
* Poll routine to call if blocked with irqs off
|
|
*/
|
|
extern void smu_poll(void);
|
|
|
|
|
|
/*
|
|
* Init routine, presence check....
|
|
*/
|
|
extern int smu_init(void);
|
|
extern int smu_present(void);
|
|
struct of_device;
|
|
extern struct of_device *smu_get_ofdev(void);
|
|
|
|
|
|
/*
|
|
* Common command wrappers
|
|
*/
|
|
extern void smu_shutdown(void);
|
|
extern void smu_restart(void);
|
|
struct rtc_time;
|
|
extern int smu_get_rtc_time(struct rtc_time *time, int spinwait);
|
|
extern int smu_set_rtc_time(struct rtc_time *time, int spinwait);
|
|
|
|
/*
|
|
* SMU command buffer absolute address, exported by pmac_setup,
|
|
* this is allocated very early during boot.
|
|
*/
|
|
extern unsigned long smu_cmdbuf_abs;
|
|
|
|
|
|
/*
|
|
* Kenrel asynchronous i2c interface
|
|
*/
|
|
|
|
/* SMU i2c header, exactly matches i2c header on wire */
|
|
struct smu_i2c_param
|
|
{
|
|
u8 bus; /* SMU bus ID (from device tree) */
|
|
u8 type; /* i2c transfer type */
|
|
u8 devaddr; /* device address (includes direction) */
|
|
u8 sublen; /* subaddress length */
|
|
u8 subaddr[3]; /* subaddress */
|
|
u8 caddr; /* combined address, filled by SMU driver */
|
|
u8 datalen; /* length of transfer */
|
|
u8 data[7]; /* data */
|
|
};
|
|
|
|
#define SMU_I2C_READ_MAX 0x0d
|
|
#define SMU_I2C_WRITE_MAX 0x05
|
|
|
|
struct smu_i2c_cmd
|
|
{
|
|
/* public */
|
|
struct smu_i2c_param info;
|
|
void (*done)(struct smu_i2c_cmd *cmd, void *misc);
|
|
void *misc;
|
|
int status; /* 1 = pending, 0 = ok, <0 = fail */
|
|
|
|
/* private */
|
|
struct smu_cmd scmd;
|
|
int read;
|
|
int stage;
|
|
int retries;
|
|
u8 pdata[0x10];
|
|
struct list_head link;
|
|
};
|
|
|
|
/*
|
|
* Call this to queue an i2c command to the SMU. You must fill info,
|
|
* including info.data for a write, done and misc.
|
|
* For now, no polling interface is provided so you have to use completion
|
|
* callback.
|
|
*/
|
|
extern int smu_queue_i2c(struct smu_i2c_cmd *cmd);
|
|
|
|
|
|
#endif /* __KERNEL__ */
|
|
|
|
/*
|
|
* - Userland interface -
|
|
*/
|
|
|
|
/*
|
|
* A given instance of the device can be configured for 2 different
|
|
* things at the moment:
|
|
*
|
|
* - sending SMU commands (default at open() time)
|
|
* - receiving SMU events (not yet implemented)
|
|
*
|
|
* Commands are written with write() of a command block. They can be
|
|
* "driver" commands (for example to switch to event reception mode)
|
|
* or real SMU commands. They are made of a header followed by command
|
|
* data if any.
|
|
*
|
|
* For SMU commands (not for driver commands), you can then read() back
|
|
* a reply. The reader will be blocked or not depending on how the device
|
|
* file is opened. poll() isn't implemented yet. The reply will consist
|
|
* of a header as well, followed by the reply data if any. You should
|
|
* always provide a buffer large enough for the maximum reply data, I
|
|
* recommand one page.
|
|
*
|
|
* It is illegal to send SMU commands through a file descriptor configured
|
|
* for events reception
|
|
*
|
|
*/
|
|
struct smu_user_cmd_hdr
|
|
{
|
|
__u32 cmdtype;
|
|
#define SMU_CMDTYPE_SMU 0 /* SMU command */
|
|
#define SMU_CMDTYPE_WANTS_EVENTS 1 /* switch fd to events mode */
|
|
|
|
__u8 cmd; /* SMU command byte */
|
|
__u32 data_len; /* Lenght of data following */
|
|
};
|
|
|
|
struct smu_user_reply_hdr
|
|
{
|
|
__u32 status; /* Command status */
|
|
__u32 reply_len; /* Lenght of data follwing */
|
|
};
|
|
|
|
#endif /* _SMU_H */
|