137 строки
5.7 KiB
C
137 строки
5.7 KiB
C
/*******************************************************************************
|
|
|
|
Intel(R) Gigabit Ethernet Linux driver
|
|
Copyright(c) 2007-2009 Intel Corporation.
|
|
|
|
This program is free software; you can redistribute it and/or modify it
|
|
under the terms and conditions of the GNU General Public License,
|
|
version 2, as published by the Free Software Foundation.
|
|
|
|
This program is distributed in the hope it will be useful, but WITHOUT
|
|
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
|
|
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
|
|
more details.
|
|
|
|
You should have received a copy of the GNU General Public License along with
|
|
this program; if not, write to the Free Software Foundation, Inc.,
|
|
51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
|
|
|
|
The full GNU General Public License is included in this distribution in
|
|
the file called "COPYING".
|
|
|
|
Contact Information:
|
|
e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
|
|
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
|
|
|
|
*******************************************************************************/
|
|
|
|
#ifndef _E1000_PHY_H_
|
|
#define _E1000_PHY_H_
|
|
|
|
enum e1000_ms_type {
|
|
e1000_ms_hw_default = 0,
|
|
e1000_ms_force_master,
|
|
e1000_ms_force_slave,
|
|
e1000_ms_auto
|
|
};
|
|
|
|
enum e1000_smart_speed {
|
|
e1000_smart_speed_default = 0,
|
|
e1000_smart_speed_on,
|
|
e1000_smart_speed_off
|
|
};
|
|
|
|
s32 igb_check_downshift(struct e1000_hw *hw);
|
|
s32 igb_check_reset_block(struct e1000_hw *hw);
|
|
s32 igb_copper_link_setup_igp(struct e1000_hw *hw);
|
|
s32 igb_copper_link_setup_m88(struct e1000_hw *hw);
|
|
s32 igb_copper_link_setup_m88_gen2(struct e1000_hw *hw);
|
|
s32 igb_phy_force_speed_duplex_igp(struct e1000_hw *hw);
|
|
s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw);
|
|
s32 igb_get_cable_length_m88(struct e1000_hw *hw);
|
|
s32 igb_get_cable_length_m88_gen2(struct e1000_hw *hw);
|
|
s32 igb_get_cable_length_igp_2(struct e1000_hw *hw);
|
|
s32 igb_get_phy_id(struct e1000_hw *hw);
|
|
s32 igb_get_phy_info_igp(struct e1000_hw *hw);
|
|
s32 igb_get_phy_info_m88(struct e1000_hw *hw);
|
|
s32 igb_phy_sw_reset(struct e1000_hw *hw);
|
|
s32 igb_phy_hw_reset(struct e1000_hw *hw);
|
|
s32 igb_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
|
|
s32 igb_set_d3_lplu_state(struct e1000_hw *hw, bool active);
|
|
s32 igb_setup_copper_link(struct e1000_hw *hw);
|
|
s32 igb_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
|
|
s32 igb_phy_has_link(struct e1000_hw *hw, u32 iterations,
|
|
u32 usec_interval, bool *success);
|
|
void igb_power_up_phy_copper(struct e1000_hw *hw);
|
|
void igb_power_down_phy_copper(struct e1000_hw *hw);
|
|
s32 igb_phy_init_script_igp3(struct e1000_hw *hw);
|
|
s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
|
|
s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
|
|
s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
|
|
s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
|
|
s32 igb_copper_link_setup_82580(struct e1000_hw *hw);
|
|
s32 igb_get_phy_info_82580(struct e1000_hw *hw);
|
|
s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
|
|
s32 igb_get_cable_length_82580(struct e1000_hw *hw);
|
|
|
|
/* IGP01E1000 Specific Registers */
|
|
#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */
|
|
#define IGP01E1000_PHY_PORT_STATUS 0x11 /* Status */
|
|
#define IGP01E1000_PHY_PORT_CTRL 0x12 /* Control */
|
|
#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */
|
|
#define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */
|
|
#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */
|
|
#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
|
|
#define IGP01E1000_PHY_POLARITY_MASK 0x0078
|
|
#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
|
|
#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */
|
|
#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
|
|
|
|
#define I82580_ADDR_REG 16
|
|
#define I82580_CFG_REG 22
|
|
#define I82580_CFG_ASSERT_CRS_ON_TX (1 << 15)
|
|
#define I82580_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */
|
|
#define I82580_CTRL_REG 23
|
|
#define I82580_CTRL_DOWNSHIFT_MASK (7 << 10)
|
|
|
|
/* 82580 specific PHY registers */
|
|
#define I82580_PHY_CTRL_2 18
|
|
#define I82580_PHY_LBK_CTRL 19
|
|
#define I82580_PHY_STATUS_2 26
|
|
#define I82580_PHY_DIAG_STATUS 31
|
|
|
|
/* I82580 PHY Status 2 */
|
|
#define I82580_PHY_STATUS2_REV_POLARITY 0x0400
|
|
#define I82580_PHY_STATUS2_MDIX 0x0800
|
|
#define I82580_PHY_STATUS2_SPEED_MASK 0x0300
|
|
#define I82580_PHY_STATUS2_SPEED_1000MBPS 0x0200
|
|
#define I82580_PHY_STATUS2_SPEED_100MBPS 0x0100
|
|
|
|
/* I82580 PHY Control 2 */
|
|
#define I82580_PHY_CTRL2_AUTO_MDIX 0x0400
|
|
#define I82580_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
|
|
|
|
/* I82580 PHY Diagnostics Status */
|
|
#define I82580_DSTATUS_CABLE_LENGTH 0x03FC
|
|
#define I82580_DSTATUS_CABLE_LENGTH_SHIFT 2
|
|
/* Enable flexible speed on link-up */
|
|
#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
|
|
#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
|
|
#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
|
|
#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
|
|
#define IGP01E1000_PSSR_MDIX 0x0800
|
|
#define IGP01E1000_PSSR_SPEED_MASK 0xC000
|
|
#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
|
|
#define IGP02E1000_PHY_CHANNEL_NUM 4
|
|
#define IGP02E1000_PHY_AGC_A 0x11B1
|
|
#define IGP02E1000_PHY_AGC_B 0x12B1
|
|
#define IGP02E1000_PHY_AGC_C 0x14B1
|
|
#define IGP02E1000_PHY_AGC_D 0x18B1
|
|
#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Course - 15:13, Fine - 12:9 */
|
|
#define IGP02E1000_AGC_LENGTH_MASK 0x7F
|
|
#define IGP02E1000_AGC_RANGE 15
|
|
|
|
#define E1000_CABLE_LENGTH_UNDEFINED 0xFF
|
|
|
|
#endif
|