1074 строки
40 KiB
ReStructuredText
1074 строки
40 KiB
ReStructuredText
=============
|
|
Event Tracing
|
|
=============
|
|
|
|
:Author: Theodore Ts'o
|
|
:Updated: Li Zefan and Tom Zanussi
|
|
|
|
1. Introduction
|
|
===============
|
|
|
|
Tracepoints (see Documentation/trace/tracepoints.rst) can be used
|
|
without creating custom kernel modules to register probe functions
|
|
using the event tracing infrastructure.
|
|
|
|
Not all tracepoints can be traced using the event tracing system;
|
|
the kernel developer must provide code snippets which define how the
|
|
tracing information is saved into the tracing buffer, and how the
|
|
tracing information should be printed.
|
|
|
|
2. Using Event Tracing
|
|
======================
|
|
|
|
2.1 Via the 'set_event' interface
|
|
---------------------------------
|
|
|
|
The events which are available for tracing can be found in the file
|
|
/sys/kernel/debug/tracing/available_events.
|
|
|
|
To enable a particular event, such as 'sched_wakeup', simply echo it
|
|
to /sys/kernel/debug/tracing/set_event. For example::
|
|
|
|
# echo sched_wakeup >> /sys/kernel/debug/tracing/set_event
|
|
|
|
.. Note:: '>>' is necessary, otherwise it will firstly disable all the events.
|
|
|
|
To disable an event, echo the event name to the set_event file prefixed
|
|
with an exclamation point::
|
|
|
|
# echo '!sched_wakeup' >> /sys/kernel/debug/tracing/set_event
|
|
|
|
To disable all events, echo an empty line to the set_event file::
|
|
|
|
# echo > /sys/kernel/debug/tracing/set_event
|
|
|
|
To enable all events, echo ``*:*`` or ``*:`` to the set_event file::
|
|
|
|
# echo *:* > /sys/kernel/debug/tracing/set_event
|
|
|
|
The events are organized into subsystems, such as ext4, irq, sched,
|
|
etc., and a full event name looks like this: <subsystem>:<event>. The
|
|
subsystem name is optional, but it is displayed in the available_events
|
|
file. All of the events in a subsystem can be specified via the syntax
|
|
``<subsystem>:*``; for example, to enable all irq events, you can use the
|
|
command::
|
|
|
|
# echo 'irq:*' > /sys/kernel/debug/tracing/set_event
|
|
|
|
2.2 Via the 'enable' toggle
|
|
---------------------------
|
|
|
|
The events available are also listed in /sys/kernel/debug/tracing/events/ hierarchy
|
|
of directories.
|
|
|
|
To enable event 'sched_wakeup'::
|
|
|
|
# echo 1 > /sys/kernel/debug/tracing/events/sched/sched_wakeup/enable
|
|
|
|
To disable it::
|
|
|
|
# echo 0 > /sys/kernel/debug/tracing/events/sched/sched_wakeup/enable
|
|
|
|
To enable all events in sched subsystem::
|
|
|
|
# echo 1 > /sys/kernel/debug/tracing/events/sched/enable
|
|
|
|
To enable all events::
|
|
|
|
# echo 1 > /sys/kernel/debug/tracing/events/enable
|
|
|
|
When reading one of these enable files, there are four results:
|
|
|
|
- 0 - all events this file affects are disabled
|
|
- 1 - all events this file affects are enabled
|
|
- X - there is a mixture of events enabled and disabled
|
|
- ? - this file does not affect any event
|
|
|
|
2.3 Boot option
|
|
---------------
|
|
|
|
In order to facilitate early boot debugging, use boot option::
|
|
|
|
trace_event=[event-list]
|
|
|
|
event-list is a comma separated list of events. See section 2.1 for event
|
|
format.
|
|
|
|
3. Defining an event-enabled tracepoint
|
|
=======================================
|
|
|
|
See The example provided in samples/trace_events
|
|
|
|
4. Event formats
|
|
================
|
|
|
|
Each trace event has a 'format' file associated with it that contains
|
|
a description of each field in a logged event. This information can
|
|
be used to parse the binary trace stream, and is also the place to
|
|
find the field names that can be used in event filters (see section 5).
|
|
|
|
It also displays the format string that will be used to print the
|
|
event in text mode, along with the event name and ID used for
|
|
profiling.
|
|
|
|
Every event has a set of ``common`` fields associated with it; these are
|
|
the fields prefixed with ``common_``. The other fields vary between
|
|
events and correspond to the fields defined in the TRACE_EVENT
|
|
definition for that event.
|
|
|
|
Each field in the format has the form::
|
|
|
|
field:field-type field-name; offset:N; size:N;
|
|
|
|
where offset is the offset of the field in the trace record and size
|
|
is the size of the data item, in bytes.
|
|
|
|
For example, here's the information displayed for the 'sched_wakeup'
|
|
event::
|
|
|
|
# cat /sys/kernel/debug/tracing/events/sched/sched_wakeup/format
|
|
|
|
name: sched_wakeup
|
|
ID: 60
|
|
format:
|
|
field:unsigned short common_type; offset:0; size:2;
|
|
field:unsigned char common_flags; offset:2; size:1;
|
|
field:unsigned char common_preempt_count; offset:3; size:1;
|
|
field:int common_pid; offset:4; size:4;
|
|
field:int common_tgid; offset:8; size:4;
|
|
|
|
field:char comm[TASK_COMM_LEN]; offset:12; size:16;
|
|
field:pid_t pid; offset:28; size:4;
|
|
field:int prio; offset:32; size:4;
|
|
field:int success; offset:36; size:4;
|
|
field:int cpu; offset:40; size:4;
|
|
|
|
print fmt: "task %s:%d [%d] success=%d [%03d]", REC->comm, REC->pid,
|
|
REC->prio, REC->success, REC->cpu
|
|
|
|
This event contains 10 fields, the first 5 common and the remaining 5
|
|
event-specific. All the fields for this event are numeric, except for
|
|
'comm' which is a string, a distinction important for event filtering.
|
|
|
|
5. Event filtering
|
|
==================
|
|
|
|
Trace events can be filtered in the kernel by associating boolean
|
|
'filter expressions' with them. As soon as an event is logged into
|
|
the trace buffer, its fields are checked against the filter expression
|
|
associated with that event type. An event with field values that
|
|
'match' the filter will appear in the trace output, and an event whose
|
|
values don't match will be discarded. An event with no filter
|
|
associated with it matches everything, and is the default when no
|
|
filter has been set for an event.
|
|
|
|
5.1 Expression syntax
|
|
---------------------
|
|
|
|
A filter expression consists of one or more 'predicates' that can be
|
|
combined using the logical operators '&&' and '||'. A predicate is
|
|
simply a clause that compares the value of a field contained within a
|
|
logged event with a constant value and returns either 0 or 1 depending
|
|
on whether the field value matched (1) or didn't match (0)::
|
|
|
|
field-name relational-operator value
|
|
|
|
Parentheses can be used to provide arbitrary logical groupings and
|
|
double-quotes can be used to prevent the shell from interpreting
|
|
operators as shell metacharacters.
|
|
|
|
The field-names available for use in filters can be found in the
|
|
'format' files for trace events (see section 4).
|
|
|
|
The relational-operators depend on the type of the field being tested:
|
|
|
|
The operators available for numeric fields are:
|
|
|
|
==, !=, <, <=, >, >=, &
|
|
|
|
And for string fields they are:
|
|
|
|
==, !=, ~
|
|
|
|
The glob (~) accepts a wild card character (\*,?) and character classes
|
|
([). For example::
|
|
|
|
prev_comm ~ "*sh"
|
|
prev_comm ~ "sh*"
|
|
prev_comm ~ "*sh*"
|
|
prev_comm ~ "ba*sh"
|
|
|
|
If the field is a pointer that points into user space (for example
|
|
"filename" from sys_enter_openat), then you have to append ".ustring" to the
|
|
field name::
|
|
|
|
filename.ustring ~ "password"
|
|
|
|
As the kernel will have to know how to retrieve the memory that the pointer
|
|
is at from user space.
|
|
|
|
5.2 Setting filters
|
|
-------------------
|
|
|
|
A filter for an individual event is set by writing a filter expression
|
|
to the 'filter' file for the given event.
|
|
|
|
For example::
|
|
|
|
# cd /sys/kernel/debug/tracing/events/sched/sched_wakeup
|
|
# echo "common_preempt_count > 4" > filter
|
|
|
|
A slightly more involved example::
|
|
|
|
# cd /sys/kernel/debug/tracing/events/signal/signal_generate
|
|
# echo "((sig >= 10 && sig < 15) || sig == 17) && comm != bash" > filter
|
|
|
|
If there is an error in the expression, you'll get an 'Invalid
|
|
argument' error when setting it, and the erroneous string along with
|
|
an error message can be seen by looking at the filter e.g.::
|
|
|
|
# cd /sys/kernel/debug/tracing/events/signal/signal_generate
|
|
# echo "((sig >= 10 && sig < 15) || dsig == 17) && comm != bash" > filter
|
|
-bash: echo: write error: Invalid argument
|
|
# cat filter
|
|
((sig >= 10 && sig < 15) || dsig == 17) && comm != bash
|
|
^
|
|
parse_error: Field not found
|
|
|
|
Currently the caret ('^') for an error always appears at the beginning of
|
|
the filter string; the error message should still be useful though
|
|
even without more accurate position info.
|
|
|
|
5.2.1 Filter limitations
|
|
------------------------
|
|
|
|
If a filter is placed on a string pointer ``(char *)`` that does not point
|
|
to a string on the ring buffer, but instead points to kernel or user space
|
|
memory, then, for safety reasons, at most 1024 bytes of the content is
|
|
copied onto a temporary buffer to do the compare. If the copy of the memory
|
|
faults (the pointer points to memory that should not be accessed), then the
|
|
string compare will be treated as not matching.
|
|
|
|
5.3 Clearing filters
|
|
--------------------
|
|
|
|
To clear the filter for an event, write a '0' to the event's filter
|
|
file.
|
|
|
|
To clear the filters for all events in a subsystem, write a '0' to the
|
|
subsystem's filter file.
|
|
|
|
5.3 Subsystem filters
|
|
---------------------
|
|
|
|
For convenience, filters for every event in a subsystem can be set or
|
|
cleared as a group by writing a filter expression into the filter file
|
|
at the root of the subsystem. Note however, that if a filter for any
|
|
event within the subsystem lacks a field specified in the subsystem
|
|
filter, or if the filter can't be applied for any other reason, the
|
|
filter for that event will retain its previous setting. This can
|
|
result in an unintended mixture of filters which could lead to
|
|
confusing (to the user who might think different filters are in
|
|
effect) trace output. Only filters that reference just the common
|
|
fields can be guaranteed to propagate successfully to all events.
|
|
|
|
Here are a few subsystem filter examples that also illustrate the
|
|
above points:
|
|
|
|
Clear the filters on all events in the sched subsystem::
|
|
|
|
# cd /sys/kernel/debug/tracing/events/sched
|
|
# echo 0 > filter
|
|
# cat sched_switch/filter
|
|
none
|
|
# cat sched_wakeup/filter
|
|
none
|
|
|
|
Set a filter using only common fields for all events in the sched
|
|
subsystem (all events end up with the same filter)::
|
|
|
|
# cd /sys/kernel/debug/tracing/events/sched
|
|
# echo common_pid == 0 > filter
|
|
# cat sched_switch/filter
|
|
common_pid == 0
|
|
# cat sched_wakeup/filter
|
|
common_pid == 0
|
|
|
|
Attempt to set a filter using a non-common field for all events in the
|
|
sched subsystem (all events but those that have a prev_pid field retain
|
|
their old filters)::
|
|
|
|
# cd /sys/kernel/debug/tracing/events/sched
|
|
# echo prev_pid == 0 > filter
|
|
# cat sched_switch/filter
|
|
prev_pid == 0
|
|
# cat sched_wakeup/filter
|
|
common_pid == 0
|
|
|
|
5.4 PID filtering
|
|
-----------------
|
|
|
|
The set_event_pid file in the same directory as the top events directory
|
|
exists, will filter all events from tracing any task that does not have the
|
|
PID listed in the set_event_pid file.
|
|
::
|
|
|
|
# cd /sys/kernel/debug/tracing
|
|
# echo $$ > set_event_pid
|
|
# echo 1 > events/enable
|
|
|
|
Will only trace events for the current task.
|
|
|
|
To add more PIDs without losing the PIDs already included, use '>>'.
|
|
::
|
|
|
|
# echo 123 244 1 >> set_event_pid
|
|
|
|
|
|
6. Event triggers
|
|
=================
|
|
|
|
Trace events can be made to conditionally invoke trigger 'commands'
|
|
which can take various forms and are described in detail below;
|
|
examples would be enabling or disabling other trace events or invoking
|
|
a stack trace whenever the trace event is hit. Whenever a trace event
|
|
with attached triggers is invoked, the set of trigger commands
|
|
associated with that event is invoked. Any given trigger can
|
|
additionally have an event filter of the same form as described in
|
|
section 5 (Event filtering) associated with it - the command will only
|
|
be invoked if the event being invoked passes the associated filter.
|
|
If no filter is associated with the trigger, it always passes.
|
|
|
|
Triggers are added to and removed from a particular event by writing
|
|
trigger expressions to the 'trigger' file for the given event.
|
|
|
|
A given event can have any number of triggers associated with it,
|
|
subject to any restrictions that individual commands may have in that
|
|
regard.
|
|
|
|
Event triggers are implemented on top of "soft" mode, which means that
|
|
whenever a trace event has one or more triggers associated with it,
|
|
the event is activated even if it isn't actually enabled, but is
|
|
disabled in a "soft" mode. That is, the tracepoint will be called,
|
|
but just will not be traced, unless of course it's actually enabled.
|
|
This scheme allows triggers to be invoked even for events that aren't
|
|
enabled, and also allows the current event filter implementation to be
|
|
used for conditionally invoking triggers.
|
|
|
|
The syntax for event triggers is roughly based on the syntax for
|
|
set_ftrace_filter 'ftrace filter commands' (see the 'Filter commands'
|
|
section of Documentation/trace/ftrace.rst), but there are major
|
|
differences and the implementation isn't currently tied to it in any
|
|
way, so beware about making generalizations between the two.
|
|
|
|
.. Note::
|
|
Writing into trace_marker (See Documentation/trace/ftrace.rst)
|
|
can also enable triggers that are written into
|
|
/sys/kernel/tracing/events/ftrace/print/trigger
|
|
|
|
6.1 Expression syntax
|
|
---------------------
|
|
|
|
Triggers are added by echoing the command to the 'trigger' file::
|
|
|
|
# echo 'command[:count] [if filter]' > trigger
|
|
|
|
Triggers are removed by echoing the same command but starting with '!'
|
|
to the 'trigger' file::
|
|
|
|
# echo '!command[:count] [if filter]' > trigger
|
|
|
|
The [if filter] part isn't used in matching commands when removing, so
|
|
leaving that off in a '!' command will accomplish the same thing as
|
|
having it in.
|
|
|
|
The filter syntax is the same as that described in the 'Event
|
|
filtering' section above.
|
|
|
|
For ease of use, writing to the trigger file using '>' currently just
|
|
adds or removes a single trigger and there's no explicit '>>' support
|
|
('>' actually behaves like '>>') or truncation support to remove all
|
|
triggers (you have to use '!' for each one added.)
|
|
|
|
6.2 Supported trigger commands
|
|
------------------------------
|
|
|
|
The following commands are supported:
|
|
|
|
- enable_event/disable_event
|
|
|
|
These commands can enable or disable another trace event whenever
|
|
the triggering event is hit. When these commands are registered,
|
|
the other trace event is activated, but disabled in a "soft" mode.
|
|
That is, the tracepoint will be called, but just will not be traced.
|
|
The event tracepoint stays in this mode as long as there's a trigger
|
|
in effect that can trigger it.
|
|
|
|
For example, the following trigger causes kmalloc events to be
|
|
traced when a read system call is entered, and the :1 at the end
|
|
specifies that this enablement happens only once::
|
|
|
|
# echo 'enable_event:kmem:kmalloc:1' > \
|
|
/sys/kernel/debug/tracing/events/syscalls/sys_enter_read/trigger
|
|
|
|
The following trigger causes kmalloc events to stop being traced
|
|
when a read system call exits. This disablement happens on every
|
|
read system call exit::
|
|
|
|
# echo 'disable_event:kmem:kmalloc' > \
|
|
/sys/kernel/debug/tracing/events/syscalls/sys_exit_read/trigger
|
|
|
|
The format is::
|
|
|
|
enable_event:<system>:<event>[:count]
|
|
disable_event:<system>:<event>[:count]
|
|
|
|
To remove the above commands::
|
|
|
|
# echo '!enable_event:kmem:kmalloc:1' > \
|
|
/sys/kernel/debug/tracing/events/syscalls/sys_enter_read/trigger
|
|
|
|
# echo '!disable_event:kmem:kmalloc' > \
|
|
/sys/kernel/debug/tracing/events/syscalls/sys_exit_read/trigger
|
|
|
|
Note that there can be any number of enable/disable_event triggers
|
|
per triggering event, but there can only be one trigger per
|
|
triggered event. e.g. sys_enter_read can have triggers enabling both
|
|
kmem:kmalloc and sched:sched_switch, but can't have two kmem:kmalloc
|
|
versions such as kmem:kmalloc and kmem:kmalloc:1 or 'kmem:kmalloc if
|
|
bytes_req == 256' and 'kmem:kmalloc if bytes_alloc == 256' (they
|
|
could be combined into a single filter on kmem:kmalloc though).
|
|
|
|
- stacktrace
|
|
|
|
This command dumps a stacktrace in the trace buffer whenever the
|
|
triggering event occurs.
|
|
|
|
For example, the following trigger dumps a stacktrace every time the
|
|
kmalloc tracepoint is hit::
|
|
|
|
# echo 'stacktrace' > \
|
|
/sys/kernel/debug/tracing/events/kmem/kmalloc/trigger
|
|
|
|
The following trigger dumps a stacktrace the first 5 times a kmalloc
|
|
request happens with a size >= 64K::
|
|
|
|
# echo 'stacktrace:5 if bytes_req >= 65536' > \
|
|
/sys/kernel/debug/tracing/events/kmem/kmalloc/trigger
|
|
|
|
The format is::
|
|
|
|
stacktrace[:count]
|
|
|
|
To remove the above commands::
|
|
|
|
# echo '!stacktrace' > \
|
|
/sys/kernel/debug/tracing/events/kmem/kmalloc/trigger
|
|
|
|
# echo '!stacktrace:5 if bytes_req >= 65536' > \
|
|
/sys/kernel/debug/tracing/events/kmem/kmalloc/trigger
|
|
|
|
The latter can also be removed more simply by the following (without
|
|
the filter)::
|
|
|
|
# echo '!stacktrace:5' > \
|
|
/sys/kernel/debug/tracing/events/kmem/kmalloc/trigger
|
|
|
|
Note that there can be only one stacktrace trigger per triggering
|
|
event.
|
|
|
|
- snapshot
|
|
|
|
This command causes a snapshot to be triggered whenever the
|
|
triggering event occurs.
|
|
|
|
The following command creates a snapshot every time a block request
|
|
queue is unplugged with a depth > 1. If you were tracing a set of
|
|
events or functions at the time, the snapshot trace buffer would
|
|
capture those events when the trigger event occurred::
|
|
|
|
# echo 'snapshot if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
To only snapshot once::
|
|
|
|
# echo 'snapshot:1 if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
To remove the above commands::
|
|
|
|
# echo '!snapshot if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
# echo '!snapshot:1 if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
Note that there can be only one snapshot trigger per triggering
|
|
event.
|
|
|
|
- traceon/traceoff
|
|
|
|
These commands turn tracing on and off when the specified events are
|
|
hit. The parameter determines how many times the tracing system is
|
|
turned on and off. If unspecified, there is no limit.
|
|
|
|
The following command turns tracing off the first time a block
|
|
request queue is unplugged with a depth > 1. If you were tracing a
|
|
set of events or functions at the time, you could then examine the
|
|
trace buffer to see the sequence of events that led up to the
|
|
trigger event::
|
|
|
|
# echo 'traceoff:1 if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
To always disable tracing when nr_rq > 1::
|
|
|
|
# echo 'traceoff if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
To remove the above commands::
|
|
|
|
# echo '!traceoff:1 if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
# echo '!traceoff if nr_rq > 1' > \
|
|
/sys/kernel/debug/tracing/events/block/block_unplug/trigger
|
|
|
|
Note that there can be only one traceon or traceoff trigger per
|
|
triggering event.
|
|
|
|
- hist
|
|
|
|
This command aggregates event hits into a hash table keyed on one or
|
|
more trace event format fields (or stacktrace) and a set of running
|
|
totals derived from one or more trace event format fields and/or
|
|
event counts (hitcount).
|
|
|
|
See Documentation/trace/histogram.rst for details and examples.
|
|
|
|
7. In-kernel trace event API
|
|
============================
|
|
|
|
In most cases, the command-line interface to trace events is more than
|
|
sufficient. Sometimes, however, applications might find the need for
|
|
more complex relationships than can be expressed through a simple
|
|
series of linked command-line expressions, or putting together sets of
|
|
commands may be simply too cumbersome. An example might be an
|
|
application that needs to 'listen' to the trace stream in order to
|
|
maintain an in-kernel state machine detecting, for instance, when an
|
|
illegal kernel state occurs in the scheduler.
|
|
|
|
The trace event subsystem provides an in-kernel API allowing modules
|
|
or other kernel code to generate user-defined 'synthetic' events at
|
|
will, which can be used to either augment the existing trace stream
|
|
and/or signal that a particular important state has occurred.
|
|
|
|
A similar in-kernel API is also available for creating kprobe and
|
|
kretprobe events.
|
|
|
|
Both the synthetic event and k/ret/probe event APIs are built on top
|
|
of a lower-level "dynevent_cmd" event command API, which is also
|
|
available for more specialized applications, or as the basis of other
|
|
higher-level trace event APIs.
|
|
|
|
The API provided for these purposes is describe below and allows the
|
|
following:
|
|
|
|
- dynamically creating synthetic event definitions
|
|
- dynamically creating kprobe and kretprobe event definitions
|
|
- tracing synthetic events from in-kernel code
|
|
- the low-level "dynevent_cmd" API
|
|
|
|
7.1 Dyamically creating synthetic event definitions
|
|
---------------------------------------------------
|
|
|
|
There are a couple ways to create a new synthetic event from a kernel
|
|
module or other kernel code.
|
|
|
|
The first creates the event in one step, using synth_event_create().
|
|
In this method, the name of the event to create and an array defining
|
|
the fields is supplied to synth_event_create(). If successful, a
|
|
synthetic event with that name and fields will exist following that
|
|
call. For example, to create a new "schedtest" synthetic event::
|
|
|
|
ret = synth_event_create("schedtest", sched_fields,
|
|
ARRAY_SIZE(sched_fields), THIS_MODULE);
|
|
|
|
The sched_fields param in this example points to an array of struct
|
|
synth_field_desc, each of which describes an event field by type and
|
|
name::
|
|
|
|
static struct synth_field_desc sched_fields[] = {
|
|
{ .type = "pid_t", .name = "next_pid_field" },
|
|
{ .type = "char[16]", .name = "next_comm_field" },
|
|
{ .type = "u64", .name = "ts_ns" },
|
|
{ .type = "u64", .name = "ts_ms" },
|
|
{ .type = "unsigned int", .name = "cpu" },
|
|
{ .type = "char[64]", .name = "my_string_field" },
|
|
{ .type = "int", .name = "my_int_field" },
|
|
};
|
|
|
|
See synth_field_size() for available types.
|
|
|
|
If field_name contains [n], the field is considered to be a static array.
|
|
|
|
If field_names contains[] (no subscript), the field is considered to
|
|
be a dynamic array, which will only take as much space in the event as
|
|
is required to hold the array.
|
|
|
|
Because space for an event is reserved before assigning field values
|
|
to the event, using dynamic arrays implies that the piecewise
|
|
in-kernel API described below can't be used with dynamic arrays. The
|
|
other non-piecewise in-kernel APIs can, however, be used with dynamic
|
|
arrays.
|
|
|
|
If the event is created from within a module, a pointer to the module
|
|
must be passed to synth_event_create(). This will ensure that the
|
|
trace buffer won't contain unreadable events when the module is
|
|
removed.
|
|
|
|
At this point, the event object is ready to be used for generating new
|
|
events.
|
|
|
|
In the second method, the event is created in several steps. This
|
|
allows events to be created dynamically and without the need to create
|
|
and populate an array of fields beforehand.
|
|
|
|
To use this method, an empty or partially empty synthetic event should
|
|
first be created using synth_event_gen_cmd_start() or
|
|
synth_event_gen_cmd_array_start(). For synth_event_gen_cmd_start(),
|
|
the name of the event along with one or more pairs of args each pair
|
|
representing a 'type field_name;' field specification should be
|
|
supplied. For synth_event_gen_cmd_array_start(), the name of the
|
|
event along with an array of struct synth_field_desc should be
|
|
supplied. Before calling synth_event_gen_cmd_start() or
|
|
synth_event_gen_cmd_array_start(), the user should create and
|
|
initialize a dynevent_cmd object using synth_event_cmd_init().
|
|
|
|
For example, to create a new "schedtest" synthetic event with two
|
|
fields::
|
|
|
|
struct dynevent_cmd cmd;
|
|
char *buf;
|
|
|
|
/* Create a buffer to hold the generated command */
|
|
buf = kzalloc(MAX_DYNEVENT_CMD_LEN, GFP_KERNEL);
|
|
|
|
/* Before generating the command, initialize the cmd object */
|
|
synth_event_cmd_init(&cmd, buf, MAX_DYNEVENT_CMD_LEN);
|
|
|
|
ret = synth_event_gen_cmd_start(&cmd, "schedtest", THIS_MODULE,
|
|
"pid_t", "next_pid_field",
|
|
"u64", "ts_ns");
|
|
|
|
Alternatively, using an array of struct synth_field_desc fields
|
|
containing the same information::
|
|
|
|
ret = synth_event_gen_cmd_array_start(&cmd, "schedtest", THIS_MODULE,
|
|
fields, n_fields);
|
|
|
|
Once the synthetic event object has been created, it can then be
|
|
populated with more fields. Fields are added one by one using
|
|
synth_event_add_field(), supplying the dynevent_cmd object, a field
|
|
type, and a field name. For example, to add a new int field named
|
|
"intfield", the following call should be made::
|
|
|
|
ret = synth_event_add_field(&cmd, "int", "intfield");
|
|
|
|
See synth_field_size() for available types. If field_name contains [n]
|
|
the field is considered to be an array.
|
|
|
|
A group of fields can also be added all at once using an array of
|
|
synth_field_desc with add_synth_fields(). For example, this would add
|
|
just the first four sched_fields::
|
|
|
|
ret = synth_event_add_fields(&cmd, sched_fields, 4);
|
|
|
|
If you already have a string of the form 'type field_name',
|
|
synth_event_add_field_str() can be used to add it as-is; it will
|
|
also automatically append a ';' to the string.
|
|
|
|
Once all the fields have been added, the event should be finalized and
|
|
registered by calling the synth_event_gen_cmd_end() function::
|
|
|
|
ret = synth_event_gen_cmd_end(&cmd);
|
|
|
|
At this point, the event object is ready to be used for tracing new
|
|
events.
|
|
|
|
7.2 Tracing synthetic events from in-kernel code
|
|
------------------------------------------------
|
|
|
|
To trace a synthetic event, there are several options. The first
|
|
option is to trace the event in one call, using synth_event_trace()
|
|
with a variable number of values, or synth_event_trace_array() with an
|
|
array of values to be set. A second option can be used to avoid the
|
|
need for a pre-formed array of values or list of arguments, via
|
|
synth_event_trace_start() and synth_event_trace_end() along with
|
|
synth_event_add_next_val() or synth_event_add_val() to add the values
|
|
piecewise.
|
|
|
|
7.2.1 Tracing a synthetic event all at once
|
|
-------------------------------------------
|
|
|
|
To trace a synthetic event all at once, the synth_event_trace() or
|
|
synth_event_trace_array() functions can be used.
|
|
|
|
The synth_event_trace() function is passed the trace_event_file
|
|
representing the synthetic event (which can be retrieved using
|
|
trace_get_event_file() using the synthetic event name, "synthetic" as
|
|
the system name, and the trace instance name (NULL if using the global
|
|
trace array)), along with an variable number of u64 args, one for each
|
|
synthetic event field, and the number of values being passed.
|
|
|
|
So, to trace an event corresponding to the synthetic event definition
|
|
above, code like the following could be used::
|
|
|
|
ret = synth_event_trace(create_synth_test, 7, /* number of values */
|
|
444, /* next_pid_field */
|
|
(u64)"clackers", /* next_comm_field */
|
|
1000000, /* ts_ns */
|
|
1000, /* ts_ms */
|
|
smp_processor_id(),/* cpu */
|
|
(u64)"Thneed", /* my_string_field */
|
|
999); /* my_int_field */
|
|
|
|
All vals should be cast to u64, and string vals are just pointers to
|
|
strings, cast to u64. Strings will be copied into space reserved in
|
|
the event for the string, using these pointers.
|
|
|
|
Alternatively, the synth_event_trace_array() function can be used to
|
|
accomplish the same thing. It is passed the trace_event_file
|
|
representing the synthetic event (which can be retrieved using
|
|
trace_get_event_file() using the synthetic event name, "synthetic" as
|
|
the system name, and the trace instance name (NULL if using the global
|
|
trace array)), along with an array of u64, one for each synthetic
|
|
event field.
|
|
|
|
To trace an event corresponding to the synthetic event definition
|
|
above, code like the following could be used::
|
|
|
|
u64 vals[7];
|
|
|
|
vals[0] = 777; /* next_pid_field */
|
|
vals[1] = (u64)"tiddlywinks"; /* next_comm_field */
|
|
vals[2] = 1000000; /* ts_ns */
|
|
vals[3] = 1000; /* ts_ms */
|
|
vals[4] = smp_processor_id(); /* cpu */
|
|
vals[5] = (u64)"thneed"; /* my_string_field */
|
|
vals[6] = 398; /* my_int_field */
|
|
|
|
The 'vals' array is just an array of u64, the number of which must
|
|
match the number of field in the synthetic event, and which must be in
|
|
the same order as the synthetic event fields.
|
|
|
|
All vals should be cast to u64, and string vals are just pointers to
|
|
strings, cast to u64. Strings will be copied into space reserved in
|
|
the event for the string, using these pointers.
|
|
|
|
In order to trace a synthetic event, a pointer to the trace event file
|
|
is needed. The trace_get_event_file() function can be used to get
|
|
it - it will find the file in the given trace instance (in this case
|
|
NULL since the top trace array is being used) while at the same time
|
|
preventing the instance containing it from going away::
|
|
|
|
schedtest_event_file = trace_get_event_file(NULL, "synthetic",
|
|
"schedtest");
|
|
|
|
Before tracing the event, it should be enabled in some way, otherwise
|
|
the synthetic event won't actually show up in the trace buffer.
|
|
|
|
To enable a synthetic event from the kernel, trace_array_set_clr_event()
|
|
can be used (which is not specific to synthetic events, so does need
|
|
the "synthetic" system name to be specified explicitly).
|
|
|
|
To enable the event, pass 'true' to it::
|
|
|
|
trace_array_set_clr_event(schedtest_event_file->tr,
|
|
"synthetic", "schedtest", true);
|
|
|
|
To disable it pass false::
|
|
|
|
trace_array_set_clr_event(schedtest_event_file->tr,
|
|
"synthetic", "schedtest", false);
|
|
|
|
Finally, synth_event_trace_array() can be used to actually trace the
|
|
event, which should be visible in the trace buffer afterwards::
|
|
|
|
ret = synth_event_trace_array(schedtest_event_file, vals,
|
|
ARRAY_SIZE(vals));
|
|
|
|
To remove the synthetic event, the event should be disabled, and the
|
|
trace instance should be 'put' back using trace_put_event_file()::
|
|
|
|
trace_array_set_clr_event(schedtest_event_file->tr,
|
|
"synthetic", "schedtest", false);
|
|
trace_put_event_file(schedtest_event_file);
|
|
|
|
If those have been successful, synth_event_delete() can be called to
|
|
remove the event::
|
|
|
|
ret = synth_event_delete("schedtest");
|
|
|
|
7.2.2 Tracing a synthetic event piecewise
|
|
-----------------------------------------
|
|
|
|
To trace a synthetic using the piecewise method described above, the
|
|
synth_event_trace_start() function is used to 'open' the synthetic
|
|
event trace::
|
|
|
|
struct synth_event_trace_state trace_state;
|
|
|
|
ret = synth_event_trace_start(schedtest_event_file, &trace_state);
|
|
|
|
It's passed the trace_event_file representing the synthetic event
|
|
using the same methods as described above, along with a pointer to a
|
|
struct synth_event_trace_state object, which will be zeroed before use and
|
|
used to maintain state between this and following calls.
|
|
|
|
Once the event has been opened, which means space for it has been
|
|
reserved in the trace buffer, the individual fields can be set. There
|
|
are two ways to do that, either one after another for each field in
|
|
the event, which requires no lookups, or by name, which does. The
|
|
tradeoff is flexibility in doing the assignments vs the cost of a
|
|
lookup per field.
|
|
|
|
To assign the values one after the other without lookups,
|
|
synth_event_add_next_val() should be used. Each call is passed the
|
|
same synth_event_trace_state object used in the synth_event_trace_start(),
|
|
along with the value to set the next field in the event. After each
|
|
field is set, the 'cursor' points to the next field, which will be set
|
|
by the subsequent call, continuing until all the fields have been set
|
|
in order. The same sequence of calls as in the above examples using
|
|
this method would be (without error-handling code)::
|
|
|
|
/* next_pid_field */
|
|
ret = synth_event_add_next_val(777, &trace_state);
|
|
|
|
/* next_comm_field */
|
|
ret = synth_event_add_next_val((u64)"slinky", &trace_state);
|
|
|
|
/* ts_ns */
|
|
ret = synth_event_add_next_val(1000000, &trace_state);
|
|
|
|
/* ts_ms */
|
|
ret = synth_event_add_next_val(1000, &trace_state);
|
|
|
|
/* cpu */
|
|
ret = synth_event_add_next_val(smp_processor_id(), &trace_state);
|
|
|
|
/* my_string_field */
|
|
ret = synth_event_add_next_val((u64)"thneed_2.01", &trace_state);
|
|
|
|
/* my_int_field */
|
|
ret = synth_event_add_next_val(395, &trace_state);
|
|
|
|
To assign the values in any order, synth_event_add_val() should be
|
|
used. Each call is passed the same synth_event_trace_state object used in
|
|
the synth_event_trace_start(), along with the field name of the field
|
|
to set and the value to set it to. The same sequence of calls as in
|
|
the above examples using this method would be (without error-handling
|
|
code)::
|
|
|
|
ret = synth_event_add_val("next_pid_field", 777, &trace_state);
|
|
ret = synth_event_add_val("next_comm_field", (u64)"silly putty",
|
|
&trace_state);
|
|
ret = synth_event_add_val("ts_ns", 1000000, &trace_state);
|
|
ret = synth_event_add_val("ts_ms", 1000, &trace_state);
|
|
ret = synth_event_add_val("cpu", smp_processor_id(), &trace_state);
|
|
ret = synth_event_add_val("my_string_field", (u64)"thneed_9",
|
|
&trace_state);
|
|
ret = synth_event_add_val("my_int_field", 3999, &trace_state);
|
|
|
|
Note that synth_event_add_next_val() and synth_event_add_val() are
|
|
incompatible if used within the same trace of an event - either one
|
|
can be used but not both at the same time.
|
|
|
|
Finally, the event won't be actually traced until it's 'closed',
|
|
which is done using synth_event_trace_end(), which takes only the
|
|
struct synth_event_trace_state object used in the previous calls::
|
|
|
|
ret = synth_event_trace_end(&trace_state);
|
|
|
|
Note that synth_event_trace_end() must be called at the end regardless
|
|
of whether any of the add calls failed (say due to a bad field name
|
|
being passed in).
|
|
|
|
7.3 Dyamically creating kprobe and kretprobe event definitions
|
|
--------------------------------------------------------------
|
|
|
|
To create a kprobe or kretprobe trace event from kernel code, the
|
|
kprobe_event_gen_cmd_start() or kretprobe_event_gen_cmd_start()
|
|
functions can be used.
|
|
|
|
To create a kprobe event, an empty or partially empty kprobe event
|
|
should first be created using kprobe_event_gen_cmd_start(). The name
|
|
of the event and the probe location should be specfied along with one
|
|
or args each representing a probe field should be supplied to this
|
|
function. Before calling kprobe_event_gen_cmd_start(), the user
|
|
should create and initialize a dynevent_cmd object using
|
|
kprobe_event_cmd_init().
|
|
|
|
For example, to create a new "schedtest" kprobe event with two fields::
|
|
|
|
struct dynevent_cmd cmd;
|
|
char *buf;
|
|
|
|
/* Create a buffer to hold the generated command */
|
|
buf = kzalloc(MAX_DYNEVENT_CMD_LEN, GFP_KERNEL);
|
|
|
|
/* Before generating the command, initialize the cmd object */
|
|
kprobe_event_cmd_init(&cmd, buf, MAX_DYNEVENT_CMD_LEN);
|
|
|
|
/*
|
|
* Define the gen_kprobe_test event with the first 2 kprobe
|
|
* fields.
|
|
*/
|
|
ret = kprobe_event_gen_cmd_start(&cmd, "gen_kprobe_test", "do_sys_open",
|
|
"dfd=%ax", "filename=%dx");
|
|
|
|
Once the kprobe event object has been created, it can then be
|
|
populated with more fields. Fields can be added using
|
|
kprobe_event_add_fields(), supplying the dynevent_cmd object along
|
|
with a variable arg list of probe fields. For example, to add a
|
|
couple additional fields, the following call could be made::
|
|
|
|
ret = kprobe_event_add_fields(&cmd, "flags=%cx", "mode=+4($stack)");
|
|
|
|
Once all the fields have been added, the event should be finalized and
|
|
registered by calling the kprobe_event_gen_cmd_end() or
|
|
kretprobe_event_gen_cmd_end() functions, depending on whether a kprobe
|
|
or kretprobe command was started::
|
|
|
|
ret = kprobe_event_gen_cmd_end(&cmd);
|
|
|
|
or::
|
|
|
|
ret = kretprobe_event_gen_cmd_end(&cmd);
|
|
|
|
At this point, the event object is ready to be used for tracing new
|
|
events.
|
|
|
|
Similarly, a kretprobe event can be created using
|
|
kretprobe_event_gen_cmd_start() with a probe name and location and
|
|
additional params such as $retval::
|
|
|
|
ret = kretprobe_event_gen_cmd_start(&cmd, "gen_kretprobe_test",
|
|
"do_sys_open", "$retval");
|
|
|
|
Similar to the synthetic event case, code like the following can be
|
|
used to enable the newly created kprobe event::
|
|
|
|
gen_kprobe_test = trace_get_event_file(NULL, "kprobes", "gen_kprobe_test");
|
|
|
|
ret = trace_array_set_clr_event(gen_kprobe_test->tr,
|
|
"kprobes", "gen_kprobe_test", true);
|
|
|
|
Finally, also similar to synthetic events, the following code can be
|
|
used to give the kprobe event file back and delete the event::
|
|
|
|
trace_put_event_file(gen_kprobe_test);
|
|
|
|
ret = kprobe_event_delete("gen_kprobe_test");
|
|
|
|
7.4 The "dynevent_cmd" low-level API
|
|
------------------------------------
|
|
|
|
Both the in-kernel synthetic event and kprobe interfaces are built on
|
|
top of a lower-level "dynevent_cmd" interface. This interface is
|
|
meant to provide the basis for higher-level interfaces such as the
|
|
synthetic and kprobe interfaces, which can be used as examples.
|
|
|
|
The basic idea is simple and amounts to providing a general-purpose
|
|
layer that can be used to generate trace event commands. The
|
|
generated command strings can then be passed to the command-parsing
|
|
and event creation code that already exists in the trace event
|
|
subystem for creating the corresponding trace events.
|
|
|
|
In a nutshell, the way it works is that the higher-level interface
|
|
code creates a struct dynevent_cmd object, then uses a couple
|
|
functions, dynevent_arg_add() and dynevent_arg_pair_add() to build up
|
|
a command string, which finally causes the command to be executed
|
|
using the dynevent_create() function. The details of the interface
|
|
are described below.
|
|
|
|
The first step in building a new command string is to create and
|
|
initialize an instance of a dynevent_cmd. Here, for instance, we
|
|
create a dynevent_cmd on the stack and initialize it::
|
|
|
|
struct dynevent_cmd cmd;
|
|
char *buf;
|
|
int ret;
|
|
|
|
buf = kzalloc(MAX_DYNEVENT_CMD_LEN, GFP_KERNEL);
|
|
|
|
dynevent_cmd_init(cmd, buf, maxlen, DYNEVENT_TYPE_FOO,
|
|
foo_event_run_command);
|
|
|
|
The dynevent_cmd initialization needs to be given a user-specified
|
|
buffer and the length of the buffer (MAX_DYNEVENT_CMD_LEN can be used
|
|
for this purpose - at 2k it's generally too big to be comfortably put
|
|
on the stack, so is dynamically allocated), a dynevent type id, which
|
|
is meant to be used to check that further API calls are for the
|
|
correct command type, and a pointer to an event-specific run_command()
|
|
callback that will be called to actually execute the event-specific
|
|
command function.
|
|
|
|
Once that's done, the command string can by built up by successive
|
|
calls to argument-adding functions.
|
|
|
|
To add a single argument, define and initialize a struct dynevent_arg
|
|
or struct dynevent_arg_pair object. Here's an example of the simplest
|
|
possible arg addition, which is simply to append the given string as
|
|
a whitespace-separated argument to the command::
|
|
|
|
struct dynevent_arg arg;
|
|
|
|
dynevent_arg_init(&arg, NULL, 0);
|
|
|
|
arg.str = name;
|
|
|
|
ret = dynevent_arg_add(cmd, &arg);
|
|
|
|
The arg object is first initialized using dynevent_arg_init() and in
|
|
this case the parameters are NULL or 0, which means there's no
|
|
optional sanity-checking function or separator appended to the end of
|
|
the arg.
|
|
|
|
Here's another more complicated example using an 'arg pair', which is
|
|
used to create an argument that consists of a couple components added
|
|
together as a unit, for example, a 'type field_name;' arg or a simple
|
|
expression arg e.g. 'flags=%cx'::
|
|
|
|
struct dynevent_arg_pair arg_pair;
|
|
|
|
dynevent_arg_pair_init(&arg_pair, dynevent_foo_check_arg_fn, 0, ';');
|
|
|
|
arg_pair.lhs = type;
|
|
arg_pair.rhs = name;
|
|
|
|
ret = dynevent_arg_pair_add(cmd, &arg_pair);
|
|
|
|
Again, the arg_pair is first initialized, in this case with a callback
|
|
function used to check the sanity of the args (for example, that
|
|
neither part of the pair is NULL), along with a character to be used
|
|
to add an operator between the pair (here none) and a separator to be
|
|
appended onto the end of the arg pair (here ';').
|
|
|
|
There's also a dynevent_str_add() function that can be used to simply
|
|
add a string as-is, with no spaces, delimeters, or arg check.
|
|
|
|
Any number of dynevent_*_add() calls can be made to build up the string
|
|
(until its length surpasses cmd->maxlen). When all the arguments have
|
|
been added and the command string is complete, the only thing left to
|
|
do is run the command, which happens by simply calling
|
|
dynevent_create()::
|
|
|
|
ret = dynevent_create(&cmd);
|
|
|
|
At that point, if the return value is 0, the dynamic event has been
|
|
created and is ready to use.
|
|
|
|
See the dynevent_cmd function definitions themselves for the details
|
|
of the API.
|