366 строки
9.7 KiB
C
366 строки
9.7 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/* Low-level parallel port routines for the Multiface 3 card
|
|
*
|
|
* Author: Joerg Dorchain <joerg@dorchain.net>
|
|
*
|
|
* (C) The elitist m68k Users(TM)
|
|
*
|
|
* based on the existing parport_amiga and lp_mfc
|
|
*
|
|
*
|
|
* From the MFC3 documentation:
|
|
*
|
|
* Miscellaneous PIA Details
|
|
* -------------------------
|
|
*
|
|
* The two open-drain interrupt outputs /IRQA and /IRQB are routed to
|
|
* /INT2 of the Z2 bus.
|
|
*
|
|
* The CPU data bus of the PIA (D0-D7) is connected to D8-D15 on the Z2
|
|
* bus. This means that any PIA registers are accessed at even addresses.
|
|
*
|
|
* Centronics Pin Connections for the PIA
|
|
* --------------------------------------
|
|
*
|
|
* The following table shows the connections between the PIA and the
|
|
* Centronics interface connector. These connections implement a single, but
|
|
* very complete, Centronics type interface. The Pin column gives the pin
|
|
* numbers of the PIA. The Centronics pin numbers can be found in the section
|
|
* "Parallel Connectors".
|
|
*
|
|
*
|
|
* Pin | PIA | Dir | Centronics Names
|
|
* -------+-----+-----+---------------------------------------------------------
|
|
* 19 | CB2 | --> | /STROBE (aka /DRDY)
|
|
* 10-17 | PBx | <-> | DATA0 - DATA7
|
|
* 18 | CB1 | <-- | /ACK
|
|
* 40 | CA1 | <-- | BUSY
|
|
* 3 | PA1 | <-- | PAPER-OUT (aka POUT)
|
|
* 4 | PA2 | <-- | SELECTED (aka SEL)
|
|
* 9 | PA7 | --> | /INIT (aka /RESET or /INPUT-PRIME)
|
|
* 6 | PA4 | <-- | /ERROR (aka /FAULT)
|
|
* 7 | PA5 | --> | DIR (aka /SELECT-IN)
|
|
* 8 | PA6 | --> | /AUTO-FEED-XT
|
|
* 39 | CA2 | --> | open
|
|
* 5 | PA3 | <-- | /ACK (same as CB1!)
|
|
* 2 | PA0 | <-- | BUSY (same as CA1!)
|
|
* -------+-----+-----+---------------------------------------------------------
|
|
*
|
|
* Should be enough to understand some of the driver.
|
|
*
|
|
* Per convention for normal use the port registers are visible.
|
|
* If you need the data direction registers, restore the value in the
|
|
* control register.
|
|
*/
|
|
|
|
#include "multiface.h"
|
|
#include <linux/module.h>
|
|
#include <linux/init.h>
|
|
#include <linux/parport.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/mc6821.h>
|
|
#include <linux/zorro.h>
|
|
#include <linux/interrupt.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/amigahw.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/amigaints.h>
|
|
|
|
/* Maximum Number of Cards supported */
|
|
#define MAX_MFC 5
|
|
|
|
#undef DEBUG
|
|
|
|
static struct parport *this_port[MAX_MFC] = {NULL, };
|
|
static volatile int dummy; /* for trigger readds */
|
|
|
|
#define pia(dev) ((struct pia *)(dev->base))
|
|
static struct parport_operations pp_mfc3_ops;
|
|
|
|
static void mfc3_write_data(struct parport *p, unsigned char data)
|
|
{
|
|
pr_debug("write_data %c\n", data);
|
|
|
|
dummy = pia(p)->pprb; /* clears irq bit */
|
|
/* Triggers also /STROBE.*/
|
|
pia(p)->pprb = data;
|
|
}
|
|
|
|
static unsigned char mfc3_read_data(struct parport *p)
|
|
{
|
|
/* clears interrupt bit. Triggers also /STROBE. */
|
|
return pia(p)->pprb;
|
|
}
|
|
|
|
static unsigned char control_pc_to_mfc3(unsigned char control)
|
|
{
|
|
unsigned char ret = 32|64;
|
|
|
|
if (control & PARPORT_CONTROL_SELECT) /* XXX: What is SELECP? */
|
|
ret &= ~32; /* /SELECT_IN */
|
|
if (control & PARPORT_CONTROL_INIT) /* INITP */
|
|
ret |= 128;
|
|
if (control & PARPORT_CONTROL_AUTOFD) /* AUTOLF */
|
|
ret &= ~64;
|
|
if (control & PARPORT_CONTROL_STROBE) /* Strobe */
|
|
/* Handled directly by hardware */;
|
|
return ret;
|
|
}
|
|
|
|
static unsigned char control_mfc3_to_pc(unsigned char control)
|
|
{
|
|
unsigned char ret = PARPORT_CONTROL_STROBE
|
|
| PARPORT_CONTROL_AUTOFD | PARPORT_CONTROL_SELECT;
|
|
|
|
if (control & 128) /* /INITP */
|
|
ret |= PARPORT_CONTROL_INIT;
|
|
if (control & 64) /* /AUTOLF */
|
|
ret &= ~PARPORT_CONTROL_AUTOFD;
|
|
if (control & 32) /* /SELECT_IN */
|
|
ret &= ~PARPORT_CONTROL_SELECT;
|
|
return ret;
|
|
}
|
|
|
|
static void mfc3_write_control(struct parport *p, unsigned char control)
|
|
{
|
|
pr_debug("write_control %02x\n", control);
|
|
pia(p)->ppra = (pia(p)->ppra & 0x1f) | control_pc_to_mfc3(control);
|
|
}
|
|
|
|
static unsigned char mfc3_read_control( struct parport *p)
|
|
{
|
|
pr_debug("read_control\n");
|
|
return control_mfc3_to_pc(pia(p)->ppra & 0xe0);
|
|
}
|
|
|
|
static unsigned char mfc3_frob_control( struct parport *p, unsigned char mask, unsigned char val)
|
|
{
|
|
unsigned char old;
|
|
|
|
pr_debug("frob_control mask %02x, value %02x\n", mask, val);
|
|
old = mfc3_read_control(p);
|
|
mfc3_write_control(p, (old & ~mask) ^ val);
|
|
return old;
|
|
}
|
|
|
|
static unsigned char status_mfc3_to_pc(unsigned char status)
|
|
{
|
|
unsigned char ret = PARPORT_STATUS_BUSY;
|
|
|
|
if (status & 1) /* Busy */
|
|
ret &= ~PARPORT_STATUS_BUSY;
|
|
if (status & 2) /* PaperOut */
|
|
ret |= PARPORT_STATUS_PAPEROUT;
|
|
if (status & 4) /* Selected */
|
|
ret |= PARPORT_STATUS_SELECT;
|
|
if (status & 8) /* Ack */
|
|
ret |= PARPORT_STATUS_ACK;
|
|
if (status & 16) /* /ERROR */
|
|
ret |= PARPORT_STATUS_ERROR;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static unsigned char mfc3_read_status(struct parport *p)
|
|
{
|
|
unsigned char status;
|
|
|
|
status = status_mfc3_to_pc(pia(p)->ppra & 0x1f);
|
|
pr_debug("read_status %02x\n", status);
|
|
return status;
|
|
}
|
|
|
|
static int use_cnt;
|
|
|
|
static irqreturn_t mfc3_interrupt(int irq, void *dev_id)
|
|
{
|
|
int i;
|
|
|
|
for( i = 0; i < MAX_MFC; i++)
|
|
if (this_port[i] != NULL)
|
|
if (pia(this_port[i])->crb & 128) { /* Board caused interrupt */
|
|
dummy = pia(this_port[i])->pprb; /* clear irq bit */
|
|
parport_generic_irq(this_port[i]);
|
|
}
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static void mfc3_enable_irq(struct parport *p)
|
|
{
|
|
pia(p)->crb |= PIA_C1_ENABLE_IRQ;
|
|
}
|
|
|
|
static void mfc3_disable_irq(struct parport *p)
|
|
{
|
|
pia(p)->crb &= ~PIA_C1_ENABLE_IRQ;
|
|
}
|
|
|
|
static void mfc3_data_forward(struct parport *p)
|
|
{
|
|
pr_debug("forward\n");
|
|
pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
|
|
pia(p)->pddrb = 255; /* all pins output */
|
|
pia(p)->crb |= PIA_DDR; /* make data register visible - default */
|
|
}
|
|
|
|
static void mfc3_data_reverse(struct parport *p)
|
|
{
|
|
pr_debug("reverse\n");
|
|
pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
|
|
pia(p)->pddrb = 0; /* all pins input */
|
|
pia(p)->crb |= PIA_DDR; /* make data register visible - default */
|
|
}
|
|
|
|
static void mfc3_init_state(struct pardevice *dev, struct parport_state *s)
|
|
{
|
|
s->u.amiga.data = 0;
|
|
s->u.amiga.datadir = 255;
|
|
s->u.amiga.status = 0;
|
|
s->u.amiga.statusdir = 0xe0;
|
|
}
|
|
|
|
static void mfc3_save_state(struct parport *p, struct parport_state *s)
|
|
{
|
|
s->u.amiga.data = pia(p)->pprb;
|
|
pia(p)->crb &= ~PIA_DDR;
|
|
s->u.amiga.datadir = pia(p)->pddrb;
|
|
pia(p)->crb |= PIA_DDR;
|
|
s->u.amiga.status = pia(p)->ppra;
|
|
pia(p)->cra &= ~PIA_DDR;
|
|
s->u.amiga.statusdir = pia(p)->pddrb;
|
|
pia(p)->cra |= PIA_DDR;
|
|
}
|
|
|
|
static void mfc3_restore_state(struct parport *p, struct parport_state *s)
|
|
{
|
|
pia(p)->pprb = s->u.amiga.data;
|
|
pia(p)->crb &= ~PIA_DDR;
|
|
pia(p)->pddrb = s->u.amiga.datadir;
|
|
pia(p)->crb |= PIA_DDR;
|
|
pia(p)->ppra = s->u.amiga.status;
|
|
pia(p)->cra &= ~PIA_DDR;
|
|
pia(p)->pddrb = s->u.amiga.statusdir;
|
|
pia(p)->cra |= PIA_DDR;
|
|
}
|
|
|
|
static struct parport_operations pp_mfc3_ops = {
|
|
.write_data = mfc3_write_data,
|
|
.read_data = mfc3_read_data,
|
|
|
|
.write_control = mfc3_write_control,
|
|
.read_control = mfc3_read_control,
|
|
.frob_control = mfc3_frob_control,
|
|
|
|
.read_status = mfc3_read_status,
|
|
|
|
.enable_irq = mfc3_enable_irq,
|
|
.disable_irq = mfc3_disable_irq,
|
|
|
|
.data_forward = mfc3_data_forward,
|
|
.data_reverse = mfc3_data_reverse,
|
|
|
|
.init_state = mfc3_init_state,
|
|
.save_state = mfc3_save_state,
|
|
.restore_state = mfc3_restore_state,
|
|
|
|
.epp_write_data = parport_ieee1284_epp_write_data,
|
|
.epp_read_data = parport_ieee1284_epp_read_data,
|
|
.epp_write_addr = parport_ieee1284_epp_write_addr,
|
|
.epp_read_addr = parport_ieee1284_epp_read_addr,
|
|
|
|
.ecp_write_data = parport_ieee1284_ecp_write_data,
|
|
.ecp_read_data = parport_ieee1284_ecp_read_data,
|
|
.ecp_write_addr = parport_ieee1284_ecp_write_addr,
|
|
|
|
.compat_write_data = parport_ieee1284_write_compat,
|
|
.nibble_read_data = parport_ieee1284_read_nibble,
|
|
.byte_read_data = parport_ieee1284_read_byte,
|
|
|
|
.owner = THIS_MODULE,
|
|
};
|
|
|
|
/* ----------- Initialisation code --------------------------------- */
|
|
|
|
static int __init parport_mfc3_init(void)
|
|
{
|
|
struct parport *p;
|
|
int pias = 0;
|
|
struct pia *pp;
|
|
struct zorro_dev *z = NULL;
|
|
|
|
if (!MACH_IS_AMIGA)
|
|
return -ENODEV;
|
|
|
|
while ((z = zorro_find_device(ZORRO_PROD_BSC_MULTIFACE_III, z))) {
|
|
unsigned long piabase = z->resource.start+PIABASE;
|
|
if (!request_mem_region(piabase, sizeof(struct pia), "PIA"))
|
|
continue;
|
|
|
|
pp = ZTWO_VADDR(piabase);
|
|
pp->crb = 0;
|
|
pp->pddrb = 255; /* all data pins output */
|
|
pp->crb = PIA_DDR|32|8;
|
|
dummy = pp->pddrb; /* reading clears interrupt */
|
|
pp->cra = 0;
|
|
pp->pddra = 0xe0; /* /RESET, /DIR ,/AUTO-FEED output */
|
|
pp->cra = PIA_DDR;
|
|
pp->ppra = 0; /* reset printer */
|
|
udelay(10);
|
|
pp->ppra = 128;
|
|
p = parport_register_port((unsigned long)pp, IRQ_AMIGA_PORTS,
|
|
PARPORT_DMA_NONE, &pp_mfc3_ops);
|
|
if (!p)
|
|
goto out_port;
|
|
|
|
if (p->irq != PARPORT_IRQ_NONE) {
|
|
if (use_cnt++ == 0)
|
|
if (request_irq(IRQ_AMIGA_PORTS, mfc3_interrupt, IRQF_SHARED, p->name, &pp_mfc3_ops))
|
|
goto out_irq;
|
|
}
|
|
p->dev = &z->dev;
|
|
|
|
this_port[pias++] = p;
|
|
pr_info("%s: Multiface III port using irq\n", p->name);
|
|
/* XXX: set operating mode */
|
|
|
|
p->private_data = (void *)piabase;
|
|
parport_announce_port (p);
|
|
|
|
if (pias >= MAX_MFC)
|
|
break;
|
|
continue;
|
|
|
|
out_irq:
|
|
parport_put_port(p);
|
|
out_port:
|
|
release_mem_region(piabase, sizeof(struct pia));
|
|
}
|
|
|
|
return pias ? 0 : -ENODEV;
|
|
}
|
|
|
|
static void __exit parport_mfc3_exit(void)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < MAX_MFC; i++) {
|
|
if (!this_port[i])
|
|
continue;
|
|
parport_remove_port(this_port[i]);
|
|
if (this_port[i]->irq != PARPORT_IRQ_NONE) {
|
|
if (--use_cnt == 0)
|
|
free_irq(IRQ_AMIGA_PORTS, &pp_mfc3_ops);
|
|
}
|
|
release_mem_region(ZTWO_PADDR(this_port[i]->private_data), sizeof(struct pia));
|
|
parport_put_port(this_port[i]);
|
|
}
|
|
}
|
|
|
|
|
|
MODULE_AUTHOR("Joerg Dorchain <joerg@dorchain.net>");
|
|
MODULE_DESCRIPTION("Parport Driver for Multiface 3 expansion cards Parallel Port");
|
|
MODULE_LICENSE("GPL");
|
|
|
|
module_init(parport_mfc3_init)
|
|
module_exit(parport_mfc3_exit)
|