260 строки
6.8 KiB
ReStructuredText
260 строки
6.8 KiB
ReStructuredText
Kernel driver zl6100
|
|
====================
|
|
|
|
Supported chips:
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL2004
|
|
|
|
Prefix: 'zl2004'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl2004-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL2005
|
|
|
|
Prefix: 'zl2005'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl2005-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL2006
|
|
|
|
Prefix: 'zl2006'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl2006-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL2008
|
|
|
|
Prefix: 'zl2008'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl2008-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL2105
|
|
|
|
Prefix: 'zl2105'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl2105-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL2106
|
|
|
|
Prefix: 'zl2106'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl2106-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL6100
|
|
|
|
Prefix: 'zl6100'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl6100-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL6105
|
|
|
|
Prefix: 'zl6105'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl6105-datasheet.pdf
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL8802
|
|
|
|
Prefix: 'zl8802'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl8802-datasheet
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL9101M
|
|
|
|
Prefix: 'zl9101'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl9101m-datasheet
|
|
|
|
* Renesas / Intersil / Zilker Labs ZL9117M
|
|
|
|
Prefix: 'zl9117'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.renesas.com/us/en/document/dst/zl9117m-datasheet
|
|
|
|
* Renesas / Intersil / Zilker Labs ZLS1003, ZLS4009
|
|
|
|
Prefix: 'zls1003', zls4009
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: Not published
|
|
|
|
* Flex BMR450, BMR451
|
|
|
|
Prefix: 'bmr450', 'bmr451'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet:
|
|
|
|
https://flexpowermodules.com/resources/fpm-techspec-bmr450-digital-pol-regulators-20a
|
|
|
|
* Flex BMR462, BMR463, BMR464
|
|
|
|
Prefixes: 'bmr462', 'bmr463', 'bmr464'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://flexpowermodules.com/resources/fpm-techspec-bmr462
|
|
|
|
* Flex BMR465, BMR467
|
|
|
|
Prefixes: 'bmr465', 'bmr467'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://flexpowermodules.com/resources/fpm-techspec-bmr465-digital-pol
|
|
|
|
* Flex BMR466
|
|
|
|
Prefixes: 'bmr466'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://flexpowermodules.com/resources/fpm-techspec-bmr466-8x12
|
|
|
|
* Flex BMR469
|
|
|
|
Prefixes: 'bmr469'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://flexpowermodules.com/resources/fpm-techspec-bmr4696001
|
|
|
|
Author: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver supports hardware monitoring for Renesas / Intersil / Zilker Labs
|
|
ZL6100 and compatible digital DC-DC controllers.
|
|
|
|
The driver is a client driver to the core PMBus driver. Please see
|
|
Documentation/hwmon/pmbus.rst and Documentation.hwmon/pmbus-core for details
|
|
on PMBus client drivers.
|
|
|
|
|
|
Usage Notes
|
|
-----------
|
|
|
|
This driver does not auto-detect devices. You will have to instantiate the
|
|
devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for
|
|
details.
|
|
|
|
.. warning::
|
|
|
|
Do not access chip registers using the i2cdump command, and do not use
|
|
any of the i2ctools commands on a command register used to save and restore
|
|
configuration data (0x11, 0x12, 0x15, 0x16, and 0xf4). The chips supported by
|
|
this driver interpret any access to those command registers (including read
|
|
commands) as request to execute the command in question. Unless write accesses
|
|
to those registers are protected, this may result in power loss, board resets,
|
|
and/or Flash corruption. Worst case, your board may turn into a brick.
|
|
|
|
|
|
Platform data support
|
|
---------------------
|
|
|
|
The driver supports standard PMBus driver platform data.
|
|
|
|
|
|
Module parameters
|
|
-----------------
|
|
|
|
delay
|
|
-----
|
|
|
|
Renesas/Intersil/Zilker Labs DC-DC controllers require a minimum interval
|
|
between I2C bus accesses. According to Intersil, the minimum interval is 2 ms,
|
|
though 1 ms appears to be sufficient and has not caused any problems in testing.
|
|
The problem is known to affect all currently supported chips. For manual override,
|
|
the driver provides a writeable module parameter, 'delay', which can be used
|
|
to set the interval to a value between 0 and 65,535 microseconds.
|
|
|
|
|
|
Sysfs entries
|
|
-------------
|
|
|
|
The following attributes are supported. Limits are read-write; all other
|
|
attributes are read-only.
|
|
|
|
======================= ========================================================
|
|
in1_label "vin"
|
|
in1_input Measured input voltage.
|
|
in1_min Minimum input voltage.
|
|
in1_max Maximum input voltage.
|
|
in1_lcrit Critical minimum input voltage.
|
|
in1_crit Critical maximum input voltage.
|
|
in1_min_alarm Input voltage low alarm.
|
|
in1_max_alarm Input voltage high alarm.
|
|
in1_lcrit_alarm Input voltage critical low alarm.
|
|
in1_crit_alarm Input voltage critical high alarm.
|
|
|
|
in2_label "vmon"
|
|
in2_input Measured voltage on VMON (ZL2004) or VDRV (ZL9101M,
|
|
ZL9117M) pin. Reported voltage is 16x the voltage on the
|
|
pin (adjusted internally by the chip).
|
|
in2_lcrit Critical minimum VMON/VDRV Voltage.
|
|
in2_crit Critical maximum VMON/VDRV voltage.
|
|
in2_lcrit_alarm VMON/VDRV voltage critical low alarm.
|
|
in2_crit_alarm VMON/VDRV voltage critical high alarm.
|
|
|
|
vmon attributes are supported on ZL2004, ZL8802,
|
|
ZL9101M, ZL9117M and ZLS4009 only.
|
|
|
|
inX_label "vout[12]"
|
|
inX_input Measured output voltage.
|
|
inX_lcrit Critical minimum output Voltage.
|
|
inX_crit Critical maximum output voltage.
|
|
inX_lcrit_alarm Critical output voltage critical low alarm.
|
|
inX_crit_alarm Critical output voltage critical high alarm.
|
|
|
|
X is 3 for ZL2004, ZL9101M, and ZL9117M,
|
|
3, 4 for ZL8802 and 2 otherwise.
|
|
|
|
curr1_label "iin"
|
|
curr1_input Measured input current.
|
|
|
|
iin attributes are supported on ZL8802 only
|
|
|
|
currY_label "iout[12]"
|
|
currY_input Measured output current.
|
|
currY_lcrit Critical minimum output current.
|
|
currY_crit Critical maximum output current.
|
|
currY_lcrit_alarm Output current critical low alarm.
|
|
currY_crit_alarm Output current critical high alarm.
|
|
|
|
Y is 2, 3 for ZL8802, 1 otherwise
|
|
|
|
temp[12]_input Measured temperature.
|
|
temp[12]_min Minimum temperature.
|
|
temp[12]_max Maximum temperature.
|
|
temp[12]_lcrit Critical low temperature.
|
|
temp[12]_crit Critical high temperature.
|
|
temp[12]_min_alarm Chip temperature low alarm.
|
|
temp[12]_max_alarm Chip temperature high alarm.
|
|
temp[12]_lcrit_alarm Chip temperature critical low alarm.
|
|
temp[12]_crit_alarm Chip temperature critical high alarm.
|
|
======================= ========================================================
|