622 строки
23 KiB
Plaintext
622 строки
23 KiB
Plaintext
------------------------------------------------------------------------------
|
|
Linux WAN Router Utilities Package
|
|
------------------------------------------------------------------------------
|
|
Version 2.2.1
|
|
Mar 28, 2001
|
|
Author: Nenad Corbic <ncorbic@sangoma.com>
|
|
Copyright (c) 1995-2001 Sangoma Technologies Inc.
|
|
------------------------------------------------------------------------------
|
|
|
|
INTRODUCTION
|
|
|
|
Wide Area Networks (WANs) are used to interconnect Local Area Networks (LANs)
|
|
and/or stand-alone hosts over vast distances with data transfer rates
|
|
significantly higher than those achievable with commonly used dial-up
|
|
connections.
|
|
|
|
Usually an external device called `WAN router' sitting on your local network
|
|
or connected to your machine's serial port provides physical connection to
|
|
WAN. Although router's job may be as simple as taking your local network
|
|
traffic, converting it to WAN format and piping it through the WAN link, these
|
|
devices are notoriously expensive, with prices as much as 2 - 5 times higher
|
|
then the price of a typical PC box.
|
|
|
|
Alternatively, considering robustness and multitasking capabilities of Linux,
|
|
an internal router can be built (most routers use some sort of stripped down
|
|
Unix-like operating system anyway). With a number of relatively inexpensive WAN
|
|
interface cards available on the market, a perfectly usable router can be
|
|
built for less than half a price of an external router. Yet a Linux box
|
|
acting as a router can still be used for other purposes, such as fire-walling,
|
|
running FTP, WWW or DNS server, etc.
|
|
|
|
This kernel module introduces the notion of a WAN Link Driver (WLD) to Linux
|
|
operating system and provides generic hardware-independent services for such
|
|
drivers. Why can existing Linux network device interface not be used for
|
|
this purpose? Well, it can. However, there are a few key differences between
|
|
a typical network interface (e.g. Ethernet) and a WAN link.
|
|
|
|
Many WAN protocols, such as X.25 and frame relay, allow for multiple logical
|
|
connections (known as `virtual circuits' in X.25 terminology) over a single
|
|
physical link. Each such virtual circuit may (and almost always does) lead
|
|
to a different geographical location and, therefore, different network. As a
|
|
result, it is the virtual circuit, not the physical link, that represents a
|
|
route and, therefore, a network interface in Linux terms.
|
|
|
|
To further complicate things, virtual circuits are usually volatile in nature
|
|
(excluding so called `permanent' virtual circuits or PVCs). With almost no
|
|
time required to set up and tear down a virtual circuit, it is highly desirable
|
|
to implement on-demand connections in order to minimize network charges. So
|
|
unlike a typical network driver, the WAN driver must be able to handle multiple
|
|
network interfaces and cope as multiple virtual circuits come into existence
|
|
and go away dynamically.
|
|
|
|
Last, but not least, WAN configuration is much more complex than that of say
|
|
Ethernet and may well amount to several dozens of parameters. Some of them
|
|
are "link-wide" while others are virtual circuit-specific. The same holds
|
|
true for WAN statistics which is by far more extensive and extremely useful
|
|
when troubleshooting WAN connections. Extending the ifconfig utility to suit
|
|
these needs may be possible, but does not seem quite reasonable. Therefore, a
|
|
WAN configuration utility and corresponding application programmer's interface
|
|
is needed for this purpose.
|
|
|
|
Most of these problems are taken care of by this module. Its goal is to
|
|
provide a user with more-or-less standard look and feel for all WAN devices and
|
|
assist a WAN device driver writer by providing common services, such as:
|
|
|
|
o User-level interface via /proc file system
|
|
o Centralized configuration
|
|
o Device management (setup, shutdown, etc.)
|
|
o Network interface management (dynamic creation/destruction)
|
|
o Protocol encapsulation/decapsulation
|
|
|
|
To ba able to use the Linux WAN Router you will also need a WAN Tools package
|
|
available from
|
|
|
|
ftp.sangoma.com/pub/linux/current_wanpipe/wanpipe-X.Y.Z.tgz
|
|
|
|
where vX.Y.Z represent the wanpipe version number.
|
|
|
|
For technical questions and/or comments please e-mail to ncorbic@sangoma.com.
|
|
For general inquiries please contact Sangoma Technologies Inc. by
|
|
|
|
Hotline: 1-800-388-2475 (USA and Canada, toll free)
|
|
Phone: (905) 474-1990 ext: 106
|
|
Fax: (905) 474-9223
|
|
E-mail: dm@sangoma.com (David Mandelstam)
|
|
WWW: http://www.sangoma.com
|
|
|
|
|
|
INSTALLATION
|
|
|
|
Please read the WanpipeForLinux.pdf manual on how to
|
|
install the WANPIPE tools and drivers properly.
|
|
|
|
|
|
After installing wanpipe package: /usr/local/wanrouter/doc.
|
|
On the ftp.sangoma.com : /linux/current_wanpipe/doc
|
|
|
|
|
|
COPYRIGHT AND LICENSING INFORMATION
|
|
|
|
This program is free software; you can redistribute it and/or modify it under
|
|
the terms of the GNU General Public License as published by the Free Software
|
|
Foundation; either version 2, or (at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful, but WITHOUT
|
|
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
|
|
FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License along with
|
|
this program; if not, write to the Free Software Foundation, Inc., 675 Mass
|
|
Ave, Cambridge, MA 02139, USA.
|
|
|
|
|
|
|
|
ACKNOWLEDGEMENTS
|
|
|
|
This product is based on the WANPIPE(tm) Multiprotocol WAN Router developed
|
|
by Sangoma Technologies Inc. for Linux 2.0.x and 2.2.x. Success of the WANPIPE
|
|
together with the next major release of Linux kernel in summer 1996 commanded
|
|
adequate changes to the WANPIPE code to take full advantage of new Linux
|
|
features.
|
|
|
|
Instead of continuing developing proprietary interface tied to Sangoma WAN
|
|
cards, we decided to separate all hardware-independent code into a separate
|
|
module and defined two levels of interfaces - one for user-level applications
|
|
and another for kernel-level WAN drivers. WANPIPE is now implemented as a
|
|
WAN driver compliant with the WAN Link Driver interface. Also a general
|
|
purpose WAN configuration utility and a set of shell scripts was developed to
|
|
support WAN router at the user level.
|
|
|
|
Many useful ideas concerning hardware-independent interface implementation
|
|
were given by Mike McLagan <mike.mclagan@linux.org> and his implementation
|
|
of the Frame Relay router and drivers for Sangoma cards (dlci/sdla).
|
|
|
|
With the new implementation of the APIs being incorporated into the WANPIPE,
|
|
a special thank goes to Alan Cox in providing insight into BSD sockets.
|
|
|
|
Special thanks to all the WANPIPE users who performed field-testing, reported
|
|
bugs and made valuable comments and suggestions that help us to improve this
|
|
product.
|
|
|
|
|
|
|
|
NEW IN THIS RELEASE
|
|
|
|
o Updated the WANCFG utility
|
|
Calls the pppconfig to configure the PPPD
|
|
for async connections.
|
|
|
|
o Added the PPPCONFIG utility
|
|
Used to configure the PPPD daemon for the
|
|
WANPIPE Async PPP and standard serial port.
|
|
The wancfg calls the pppconfig to configure
|
|
the pppd.
|
|
|
|
o Fixed the PCI autodetect feature.
|
|
The SLOT 0 was used as an autodetect option
|
|
however, some high end PC's slot numbers start
|
|
from 0.
|
|
|
|
o This release has been tested with the new backupd
|
|
daemon release.
|
|
|
|
|
|
PRODUCT COMPONENTS AND RELATED FILES
|
|
|
|
/etc: (or user defined)
|
|
wanpipe1.conf default router configuration file
|
|
|
|
/lib/modules/X.Y.Z/misc:
|
|
wanrouter.o router kernel loadable module
|
|
af_wanpipe.o wanpipe api socket module
|
|
|
|
/lib/modules/X.Y.Z/net:
|
|
sdladrv.o Sangoma SDLA support module
|
|
wanpipe.o Sangoma WANPIPE(tm) driver module
|
|
|
|
/proc/net/wanrouter
|
|
Config reads current router configuration
|
|
Status reads current router status
|
|
{name} reads WAN driver statistics
|
|
|
|
/usr/sbin:
|
|
wanrouter wanrouter start-up script
|
|
wanconfig wanrouter configuration utility
|
|
sdladump WANPIPE adapter memory dump utility
|
|
fpipemon Monitor for Frame Relay
|
|
cpipemon Monitor for Cisco HDLC
|
|
ppipemon Monitor for PPP
|
|
xpipemon Monitor for X25
|
|
wpkbdmon WANPIPE keyboard led monitor/debugger
|
|
|
|
/usr/local/wanrouter:
|
|
README this file
|
|
COPYING GNU General Public License
|
|
Setup installation script
|
|
Filelist distribution definition file
|
|
wanrouter.rc meta-configuration file
|
|
(used by the Setup and wanrouter script)
|
|
|
|
/usr/local/wanrouter/doc:
|
|
wanpipeForLinux.pdf WAN Router User's Manual
|
|
|
|
/usr/local/wanrouter/patches:
|
|
wanrouter-v2213.gz patch for Linux kernels 2.2.11 up to 2.2.13.
|
|
wanrouter-v2214.gz patch for Linux kernel 2.2.14.
|
|
wanrouter-v2215.gz patch for Linux kernels 2.2.15 to 2.2.17.
|
|
wanrouter-v2218.gz patch for Linux kernels 2.2.18 and up.
|
|
wanrouter-v240.gz patch for Linux kernel 2.4.0.
|
|
wanrouter-v242.gz patch for Linux kernel 2.4.2 and up.
|
|
wanrouter-v2034.gz patch for Linux kernel 2.0.34
|
|
wanrouter-v2036.gz patch for Linux kernel 2.0.36 and up.
|
|
|
|
/usr/local/wanrouter/patches/kdrivers:
|
|
Sources of the latest WANPIPE device drivers.
|
|
These are used to UPGRADE the linux kernel to the newest
|
|
version if the kernel source has already been patched with
|
|
WANPIPE drivers.
|
|
|
|
/usr/local/wanrouter/samples:
|
|
interface sample interface configuration file
|
|
wanpipe1.cpri CHDLC primary port
|
|
wanpipe2.csec CHDLC secondary port
|
|
wanpipe1.fr Frame Relay protocol
|
|
wanpipe1.ppp PPP protocol )
|
|
wanpipe1.asy CHDLC ASYNC protocol
|
|
wanpipe1.x25 X25 protocol
|
|
wanpipe1.stty Sync TTY driver (Used by Kernel PPPD daemon)
|
|
wanpipe1.atty Async TTY driver (Used by Kernel PPPD daemon)
|
|
wanrouter.rc sample meta-configuration file
|
|
|
|
/usr/local/wanrouter/util:
|
|
* wan-tools utilities source code
|
|
|
|
/usr/local/wanrouter/api/x25:
|
|
* x25 api sample programs.
|
|
/usr/local/wanrouter/api/chdlc:
|
|
* chdlc api sample programs.
|
|
/usr/local/wanrouter/api/fr:
|
|
* fr api sample programs.
|
|
/usr/local/wanrouter/config/wancfg:
|
|
wancfg WANPIPE GUI configuration program.
|
|
Creates wanpipe#.conf files.
|
|
/usr/local/wanrouter/config/cfgft1:
|
|
cfgft1 GUI CSU/DSU configuration program.
|
|
|
|
/usr/include/linux:
|
|
wanrouter.h router API definitions
|
|
wanpipe.h WANPIPE API definitions
|
|
sdladrv.h SDLA support module API definitions
|
|
sdlasfm.h SDLA firmware module definitions
|
|
if_wanpipe.h WANPIPE Socket definitions
|
|
sdlapci.h WANPIPE PCI definitions
|
|
|
|
|
|
/usr/src/linux/net/wanrouter:
|
|
* wanrouter source code
|
|
|
|
/var/log:
|
|
wanrouter wanrouter start-up log (created by the Setup script)
|
|
|
|
/var/lock: (or /var/lock/subsys for RedHat)
|
|
wanrouter wanrouter lock file (created by the Setup script)
|
|
|
|
/usr/local/wanrouter/firmware:
|
|
fr514.sfm Frame relay firmware for Sangoma S508/S514 card
|
|
cdual514.sfm Dual Port Cisco HDLC firmware for Sangoma S508/S514 card
|
|
ppp514.sfm PPP Firmware for Sangoma S508 and S514 cards
|
|
x25_508.sfm X25 Firmware for Sangoma S508 card.
|
|
|
|
|
|
REVISION HISTORY
|
|
|
|
1.0.0 December 31, 1996 Initial version
|
|
|
|
1.0.1 January 30, 1997 Status and statistics can be read via /proc
|
|
filesystem entries.
|
|
|
|
1.0.2 April 30, 1997 Added UDP management via monitors.
|
|
|
|
1.0.3 June 3, 1997 UDP management for multiple boards using Frame
|
|
Relay and PPP
|
|
Enabled continuous transmission of Configure
|
|
Request Packet for PPP (for 508 only)
|
|
Connection Timeout for PPP changed from 900 to 0
|
|
Flow Control Problem fixed for Frame Relay
|
|
|
|
1.0.4 July 10, 1997 S508/FT1 monitoring capability in fpipemon and
|
|
ppipemon utilities.
|
|
Configurable TTL for UDP packets.
|
|
Multicast and Broadcast IP source addresses are
|
|
silently discarded.
|
|
|
|
1.0.5 July 28, 1997 Configurable T391,T392,N391,N392,N393 for Frame
|
|
Relay in router.conf.
|
|
Configurable Memory Address through router.conf
|
|
for Frame Relay, PPP and X.25. (commenting this
|
|
out enables auto-detection).
|
|
Fixed freeing up received buffers using kfree()
|
|
for Frame Relay and X.25.
|
|
Protect sdla_peek() by calling save_flags(),
|
|
cli() and restore_flags().
|
|
Changed number of Trace elements from 32 to 20
|
|
Added DLCI specific data monitoring in FPIPEMON.
|
|
2.0.0 Nov 07, 1997 Implemented protection of RACE conditions by
|
|
critical flags for FRAME RELAY and PPP.
|
|
DLCI List interrupt mode implemented.
|
|
IPX support in FRAME RELAY and PPP.
|
|
IPX Server Support (MARS)
|
|
More driver specific stats included in FPIPEMON
|
|
and PIPEMON.
|
|
|
|
2.0.1 Nov 28, 1997 Bug Fixes for version 2.0.0.
|
|
Protection of "enable_irq()" while
|
|
"disable_irq()" has been enabled from any other
|
|
routine (for Frame Relay, PPP and X25).
|
|
Added additional Stats for Fpipemon and Ppipemon
|
|
Improved Load Sharing for multiple boards
|
|
|
|
2.0.2 Dec 09, 1997 Support for PAP and CHAP for ppp has been
|
|
implemented.
|
|
|
|
2.0.3 Aug 15, 1998 New release supporting Cisco HDLC, CIR for Frame
|
|
relay, Dynamic IP assignment for PPP and Inverse
|
|
Arp support for Frame-relay. Man Pages are
|
|
included for better support and a new utility
|
|
for configuring FT1 cards.
|
|
|
|
2.0.4 Dec 09, 1998 Dual Port support for Cisco HDLC.
|
|
Support for HDLC (LAPB) API.
|
|
Supports BiSync Streaming code for S502E
|
|
and S503 cards.
|
|
Support for Streaming HDLC API.
|
|
Provides a BSD socket interface for
|
|
creating applications using BiSync
|
|
streaming.
|
|
|
|
2.0.5 Aug 04, 1999 CHDLC initialization bug fix.
|
|
PPP interrupt driven driver:
|
|
Fix to the PPP line hangup problem.
|
|
New PPP firmware
|
|
Added comments to the startup SYSTEM ERROR messages
|
|
Xpipemon debugging application for the X25 protocol
|
|
New USER_MANUAL.txt
|
|
Fixed the odd boundary 4byte writes to the board.
|
|
BiSync Streaming code has been taken out.
|
|
Available as a patch.
|
|
Streaming HDLC API has been taken out.
|
|
Available as a patch.
|
|
|
|
2.0.6 Aug 17, 1999 Increased debugging in statup scripts
|
|
Fixed installation bugs from 2.0.5
|
|
Kernel patch works for both 2.2.10 and 2.2.11 kernels.
|
|
There is no functional difference between the two packages
|
|
|
|
2.0.7 Aug 26, 1999 o Merged X25API code into WANPIPE.
|
|
o Fixed a memory leak for X25API
|
|
o Updated the X25API code for 2.2.X kernels.
|
|
o Improved NEM handling.
|
|
|
|
2.1.0 Oct 25, 1999 o New code for S514 PCI Card
|
|
o New CHDLC and Frame Relay drivers
|
|
o PPP and X25 are not supported in this release
|
|
|
|
2.1.1 Nov 30, 1999 o PPP support for S514 PCI Cards
|
|
|
|
2.1.3 Apr 06, 2000 o Socket based x25api
|
|
o Socket based chdlc api
|
|
o Socket based fr api
|
|
o Dual Port Receive only CHDLC support.
|
|
o Asynchronous CHDLC support (Secondary Port)
|
|
o cfgft1 GUI csu/dsu configurator
|
|
o wancfg GUI configuration file
|
|
configurator.
|
|
o Architectural directory changes.
|
|
|
|
beta-2.1.4 Jul 2000 o Dynamic interface configuration:
|
|
Network interfaces reflect the state
|
|
of protocol layer. If the protocol becomes
|
|
disconnected, driver will bring down
|
|
the interface. Once the protocol reconnects
|
|
the interface will be brought up.
|
|
|
|
Note: This option is turned off by default.
|
|
|
|
o Dynamic wanrouter setup using 'wanconfig':
|
|
wanconfig utility can be used to
|
|
shutdown,restart,start or reconfigure
|
|
a virtual circuit dynamically.
|
|
|
|
Frame Relay: Each DLCI can be:
|
|
created,stopped,restarted and reconfigured
|
|
dynamically using wanconfig.
|
|
|
|
ex: wanconfig card wanpipe1 dev wp1_fr16 up
|
|
|
|
o Wanrouter startup via command line arguments:
|
|
wanconfig also supports wanrouter startup via command line
|
|
arguments. Thus, there is no need to create a wanpipe#.conf
|
|
configuration file.
|
|
|
|
o Socket based x25api update/bug fixes.
|
|
Added support for LCN numbers greater than 255.
|
|
Option to pass up modem messages.
|
|
Provided a PCI IRQ check, so a single S514
|
|
card is guaranteed to have a non-sharing interrupt.
|
|
|
|
o Fixes to the wancfg utility.
|
|
o New FT1 debugging support via *pipemon utilities.
|
|
o Frame Relay ARP support Enabled.
|
|
|
|
beta3-2.1.4 Jul 2000 o X25 M_BIT Problem fix.
|
|
o Added the Multi-Port PPP
|
|
Updated utilities for the Multi-Port PPP.
|
|
|
|
2.1.4 Aut 2000
|
|
o In X25API:
|
|
Maximum packet an application can send
|
|
to the driver has been extended to 4096 bytes.
|
|
|
|
Fixed the x25 startup bug. Enable
|
|
communications only after all interfaces
|
|
come up. HIGH SVC/PVC is used to calculate
|
|
the number of channels.
|
|
Enable protocol only after all interfaces
|
|
are enabled.
|
|
|
|
o Added an extra state to the FT1 config, kernel module.
|
|
o Updated the pipemon debuggers.
|
|
|
|
o Blocked the Multi-Port PPP from running on kernels
|
|
2.2.16 or greater, due to syncppp kernel module
|
|
change.
|
|
|
|
beta1-2.1.5 Nov 15 2000
|
|
o Fixed the MultiPort PPP Support for kernels 2.2.16 and above.
|
|
2.2.X kernels only
|
|
|
|
o Secured the driver UDP debugging calls
|
|
- All illegal network debugging calls are reported to
|
|
the log.
|
|
- Defined a set of allowed commands, all other denied.
|
|
|
|
o Cpipemon
|
|
- Added set FT1 commands to the cpipemon. Thus CSU/DSU
|
|
configuration can be performed using cpipemon.
|
|
All systems that cannot run cfgft1 GUI utility should
|
|
use cpipemon to configure the on board CSU/DSU.
|
|
|
|
|
|
o Keyboard Led Monitor/Debugger
|
|
- A new utility /usr/sbin/wpkbdmon uses keyboard leds
|
|
to convey operational statistic information of the
|
|
Sangoma WANPIPE cards.
|
|
NUM_LOCK = Line State (On=connected, Off=disconnected)
|
|
CAPS_LOCK = Tx data (On=transmitting, Off=no tx data)
|
|
SCROLL_LOCK = Rx data (On=receiving, Off=no rx data
|
|
|
|
o Hardware probe on module load and dynamic device allocation
|
|
- During WANPIPE module load, all Sangoma cards are probed
|
|
and found information is printed in the /var/log/messages.
|
|
- If no cards are found, the module load fails.
|
|
- Appropriate number of devices are dynamically loaded
|
|
based on the number of Sangoma cards found.
|
|
|
|
Note: The kernel configuration option
|
|
CONFIG_WANPIPE_CARDS has been taken out.
|
|
|
|
o Fixed the Frame Relay and Chdlc network interfaces so they are
|
|
compatible with libpcap libraries. Meaning, tcpdump, snort,
|
|
ethereal, and all other packet sniffers and debuggers work on
|
|
all WANPIPE network interfaces.
|
|
- Set the network interface encoding type to ARPHRD_PPP.
|
|
This tell the sniffers that data obtained from the
|
|
network interface is in pure IP format.
|
|
Fix for 2.2.X kernels only.
|
|
|
|
o True interface encoding option for Frame Relay and CHDLC
|
|
- The above fix sets the network interface encoding
|
|
type to ARPHRD_PPP, however some customers use
|
|
the encoding interface type to determine the
|
|
protocol running. Therefore, the TURE ENCODING
|
|
option will set the interface type back to the
|
|
original value.
|
|
|
|
NOTE: If this option is used with Frame Relay and CHDLC
|
|
libpcap library support will be broken.
|
|
i.e. tcpdump will not work.
|
|
Fix for 2.2.x Kernels only.
|
|
|
|
o Ethernet Bridgind over Frame Relay
|
|
- The Frame Relay bridging has been developed by
|
|
Kristian Hoffmann and Mark Wells.
|
|
- The Linux kernel bridge is used to send ethernet
|
|
data over the frame relay links.
|
|
For 2.2.X Kernels only.
|
|
|
|
o Added extensive 2.0.X support. Most new features of
|
|
2.1.5 for protocols Frame Relay, PPP and CHDLC are
|
|
supported under 2.0.X kernels.
|
|
|
|
beta1-2.2.0 Dec 30 2000
|
|
o Updated drivers for 2.4.X kernels.
|
|
o Updated drivers for SMP support.
|
|
o X25API is now able to share PCI interrupts.
|
|
o Took out a general polling routine that was used
|
|
only by X25API.
|
|
o Added appropriate locks to the dynamic reconfiguration
|
|
code.
|
|
o Fixed a bug in the keyboard debug monitor.
|
|
|
|
beta2-2.2.0 Jan 8 2001
|
|
o Patches for 2.4.0 kernel
|
|
o Patches for 2.2.18 kernel
|
|
o Minor updates to PPP and CHLDC drivers.
|
|
Note: No functional difference.
|
|
|
|
beta3-2.2.9 Jan 10 2001
|
|
o I missed the 2.2.18 kernel patches in beta2-2.2.0
|
|
release. They are included in this release.
|
|
|
|
Stable Release
|
|
2.2.0 Feb 01 2001
|
|
o Bug fix in wancfg GUI configurator.
|
|
The edit function didn't work properly.
|
|
|
|
|
|
bata1-2.2.1 Feb 09 2001
|
|
o WANPIPE TTY Driver emulation.
|
|
Two modes of operation Sync and Async.
|
|
Sync: Using the PPPD daemon, kernel SyncPPP layer
|
|
and the Wanpipe sync TTY driver: a PPP protocol
|
|
connection can be established via Sangoma adapter, over
|
|
a T1 leased line.
|
|
|
|
The 2.4.0 kernel PPP layer supports MULTILINK
|
|
protocol, that can be used to bundle any number of Sangoma
|
|
adapters (T1 lines) into one, under a single IP address.
|
|
Thus, efficiently obtaining multiple T1 throughput.
|
|
|
|
NOTE: The remote side must also implement MULTILINK PPP
|
|
protocol.
|
|
|
|
Async:Using the PPPD daemon, kernel AsyncPPP layer
|
|
and the WANPIPE async TTY driver: a PPP protocol
|
|
connection can be established via Sangoma adapter and
|
|
a modem, over a telephone line.
|
|
|
|
Thus, the WANPIPE async TTY driver simulates a serial
|
|
TTY driver that would normally be used to interface the
|
|
MODEM to the linux kernel.
|
|
|
|
o WANPIPE PPP Backup Utility
|
|
This utility will monitor the state of the PPP T1 line.
|
|
In case of failure, a dial up connection will be established
|
|
via pppd daemon, ether via a serial tty driver (serial port),
|
|
or a WANPIPE async TTY driver (in case serial port is unavailable).
|
|
|
|
Furthermore, while in dial up mode, the primary PPP T1 link
|
|
will be monitored for signs of life.
|
|
|
|
If the PPP T1 link comes back to life, the dial up connection
|
|
will be shutdown and T1 line re-established.
|
|
|
|
|
|
o New Setup installation script.
|
|
Option to UPGRADE device drivers if the kernel source has
|
|
already been patched with WANPIPE.
|
|
|
|
Option to COMPILE WANPIPE modules against the currently
|
|
running kernel, thus no need for manual kernel and module
|
|
re-compilation.
|
|
|
|
o Updates and Bug Fixes to wancfg utility.
|
|
|
|
bata2-2.2.1 Feb 20 2001
|
|
|
|
o Bug fixes to the CHDLC device drivers.
|
|
The driver had compilation problems under kernels
|
|
2.2.14 or lower.
|
|
|
|
o Bug fixes to the Setup installation script.
|
|
The device drivers compilation options didn't work
|
|
properly.
|
|
|
|
o Update to the wpbackupd daemon.
|
|
Optimized the cross-over times, between the primary
|
|
link and the backup dialup.
|
|
|
|
beta3-2.2.1 Mar 02 2001
|
|
o Patches for 2.4.2 kernel.
|
|
|
|
o Bug fixes to util/ make files.
|
|
o Bug fixes to the Setup installation script.
|
|
|
|
o Took out the backupd support and made it into
|
|
as separate package.
|
|
|
|
beta4-2.2.1 Mar 12 2001
|
|
|
|
o Fix to the Frame Relay Device driver.
|
|
IPSAC sends a packet of zero length
|
|
header to the frame relay driver. The
|
|
driver tries to push its own 2 byte header
|
|
into the packet, which causes the driver to
|
|
crash.
|
|
|
|
o Fix the WANPIPE re-configuration code.
|
|
Bug was found by trying to run the cfgft1 while the
|
|
interface was already running.
|
|
|
|
o Updates to cfgft1.
|
|
Writes a wanpipe#.cfgft1 configuration file
|
|
once the CSU/DSU is configured. This file can
|
|
holds the current CSU/DSU configuration.
|
|
|
|
|
|
|
|
>>>>>> END OF README <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
|
|
|
|
|