WSL2-Linux-Kernel/Documentation/x86/exception-tables.txt

328 строки
13 KiB
Plaintext

Kernel level exception handling in Linux
Commentary by Joerg Pommnitz <joerg@raleigh.ibm.com>
When a process runs in kernel mode, it often has to access user
mode memory whose address has been passed by an untrusted program.
To protect itself the kernel has to verify this address.
In older versions of Linux this was done with the
int verify_area(int type, const void * addr, unsigned long size)
function (which has since been replaced by access_ok()).
This function verified that the memory area starting at address
'addr' and of size 'size' was accessible for the operation specified
in type (read or write). To do this, verify_read had to look up the
virtual memory area (vma) that contained the address addr. In the
normal case (correctly working program), this test was successful.
It only failed for a few buggy programs. In some kernel profiling
tests, this normally unneeded verification used up a considerable
amount of time.
To overcome this situation, Linus decided to let the virtual memory
hardware present in every Linux-capable CPU handle this test.
How does this work?
Whenever the kernel tries to access an address that is currently not
accessible, the CPU generates a page fault exception and calls the
page fault handler
void do_page_fault(struct pt_regs *regs, unsigned long error_code)
in arch/x86/mm/fault.c. The parameters on the stack are set up by
the low level assembly glue in arch/x86/kernel/entry_32.S. The parameter
regs is a pointer to the saved registers on the stack, error_code
contains a reason code for the exception.
do_page_fault first obtains the unaccessible address from the CPU
control register CR2. If the address is within the virtual address
space of the process, the fault probably occurred, because the page
was not swapped in, write protected or something similar. However,
we are interested in the other case: the address is not valid, there
is no vma that contains this address. In this case, the kernel jumps
to the bad_area label.
There it uses the address of the instruction that caused the exception
(i.e. regs->eip) to find an address where the execution can continue
(fixup). If this search is successful, the fault handler modifies the
return address (again regs->eip) and returns. The execution will
continue at the address in fixup.
Where does fixup point to?
Since we jump to the contents of fixup, fixup obviously points
to executable code. This code is hidden inside the user access macros.
I have picked the get_user macro defined in arch/x86/include/asm/uaccess.h
as an example. The definition is somewhat hard to follow, so let's peek at
the code generated by the preprocessor and the compiler. I selected
the get_user call in drivers/char/sysrq.c for a detailed examination.
The original code in sysrq.c line 587:
get_user(c, buf);
The preprocessor output (edited to become somewhat readable):
(
{
long __gu_err = - 14 , __gu_val = 0;
const __typeof__(*( ( buf ) )) *__gu_addr = ((buf));
if (((((0 + current_set[0])->tss.segment) == 0x18 ) ||
(((sizeof(*(buf))) <= 0xC0000000UL) &&
((unsigned long)(__gu_addr ) <= 0xC0000000UL - (sizeof(*(buf)))))))
do {
__gu_err = 0;
switch ((sizeof(*(buf)))) {
case 1:
__asm__ __volatile__(
"1: mov" "b" " %2,%" "b" "1\n"
"2:\n"
".section .fixup,\"ax\"\n"
"3: movl %3,%0\n"
" xor" "b" " %" "b" "1,%" "b" "1\n"
" jmp 2b\n"
".section __ex_table,\"a\"\n"
" .align 4\n"
" .long 1b,3b\n"
".text" : "=r"(__gu_err), "=q" (__gu_val): "m"((*(struct __large_struct *)
( __gu_addr )) ), "i"(- 14 ), "0"( __gu_err )) ;
break;
case 2:
__asm__ __volatile__(
"1: mov" "w" " %2,%" "w" "1\n"
"2:\n"
".section .fixup,\"ax\"\n"
"3: movl %3,%0\n"
" xor" "w" " %" "w" "1,%" "w" "1\n"
" jmp 2b\n"
".section __ex_table,\"a\"\n"
" .align 4\n"
" .long 1b,3b\n"
".text" : "=r"(__gu_err), "=r" (__gu_val) : "m"((*(struct __large_struct *)
( __gu_addr )) ), "i"(- 14 ), "0"( __gu_err ));
break;
case 4:
__asm__ __volatile__(
"1: mov" "l" " %2,%" "" "1\n"
"2:\n"
".section .fixup,\"ax\"\n"
"3: movl %3,%0\n"
" xor" "l" " %" "" "1,%" "" "1\n"
" jmp 2b\n"
".section __ex_table,\"a\"\n"
" .align 4\n" " .long 1b,3b\n"
".text" : "=r"(__gu_err), "=r" (__gu_val) : "m"((*(struct __large_struct *)
( __gu_addr )) ), "i"(- 14 ), "0"(__gu_err));
break;
default:
(__gu_val) = __get_user_bad();
}
} while (0) ;
((c)) = (__typeof__(*((buf))))__gu_val;
__gu_err;
}
);
WOW! Black GCC/assembly magic. This is impossible to follow, so let's
see what code gcc generates:
> xorl %edx,%edx
> movl current_set,%eax
> cmpl $24,788(%eax)
> je .L1424
> cmpl $-1073741825,64(%esp)
> ja .L1423
> .L1424:
> movl %edx,%eax
> movl 64(%esp),%ebx
> #APP
> 1: movb (%ebx),%dl /* this is the actual user access */
> 2:
> .section .fixup,"ax"
> 3: movl $-14,%eax
> xorb %dl,%dl
> jmp 2b
> .section __ex_table,"a"
> .align 4
> .long 1b,3b
> .text
> #NO_APP
> .L1423:
> movzbl %dl,%esi
The optimizer does a good job and gives us something we can actually
understand. Can we? The actual user access is quite obvious. Thanks
to the unified address space we can just access the address in user
memory. But what does the .section stuff do?????
To understand this we have to look at the final kernel:
> objdump --section-headers vmlinux
>
> vmlinux: file format elf32-i386
>
> Sections:
> Idx Name Size VMA LMA File off Algn
> 0 .text 00098f40 c0100000 c0100000 00001000 2**4
> CONTENTS, ALLOC, LOAD, READONLY, CODE
> 1 .fixup 000016bc c0198f40 c0198f40 00099f40 2**0
> CONTENTS, ALLOC, LOAD, READONLY, CODE
> 2 .rodata 0000f127 c019a5fc c019a5fc 0009b5fc 2**2
> CONTENTS, ALLOC, LOAD, READONLY, DATA
> 3 __ex_table 000015c0 c01a9724 c01a9724 000aa724 2**2
> CONTENTS, ALLOC, LOAD, READONLY, DATA
> 4 .data 0000ea58 c01abcf0 c01abcf0 000abcf0 2**4
> CONTENTS, ALLOC, LOAD, DATA
> 5 .bss 00018e21 c01ba748 c01ba748 000ba748 2**2
> ALLOC
> 6 .comment 00000ec4 00000000 00000000 000ba748 2**0
> CONTENTS, READONLY
> 7 .note 00001068 00000ec4 00000ec4 000bb60c 2**0
> CONTENTS, READONLY
There are obviously 2 non standard ELF sections in the generated object
file. But first we want to find out what happened to our code in the
final kernel executable:
> objdump --disassemble --section=.text vmlinux
>
> c017e785 <do_con_write+c1> xorl %edx,%edx
> c017e787 <do_con_write+c3> movl 0xc01c7bec,%eax
> c017e78c <do_con_write+c8> cmpl $0x18,0x314(%eax)
> c017e793 <do_con_write+cf> je c017e79f <do_con_write+db>
> c017e795 <do_con_write+d1> cmpl $0xbfffffff,0x40(%esp,1)
> c017e79d <do_con_write+d9> ja c017e7a7 <do_con_write+e3>
> c017e79f <do_con_write+db> movl %edx,%eax
> c017e7a1 <do_con_write+dd> movl 0x40(%esp,1),%ebx
> c017e7a5 <do_con_write+e1> movb (%ebx),%dl
> c017e7a7 <do_con_write+e3> movzbl %dl,%esi
The whole user memory access is reduced to 10 x86 machine instructions.
The instructions bracketed in the .section directives are no longer
in the normal execution path. They are located in a different section
of the executable file:
> objdump --disassemble --section=.fixup vmlinux
>
> c0199ff5 <.fixup+10b5> movl $0xfffffff2,%eax
> c0199ffa <.fixup+10ba> xorb %dl,%dl
> c0199ffc <.fixup+10bc> jmp c017e7a7 <do_con_write+e3>
And finally:
> objdump --full-contents --section=__ex_table vmlinux
>
> c01aa7c4 93c017c0 e09f19c0 97c017c0 99c017c0 ................
> c01aa7d4 f6c217c0 e99f19c0 a5e717c0 f59f19c0 ................
> c01aa7e4 080a18c0 01a019c0 0a0a18c0 04a019c0 ................
or in human readable byte order:
> c01aa7c4 c017c093 c0199fe0 c017c097 c017c099 ................
> c01aa7d4 c017c2f6 c0199fe9 c017e7a5 c0199ff5 ................
^^^^^^^^^^^^^^^^^
this is the interesting part!
> c01aa7e4 c0180a08 c019a001 c0180a0a c019a004 ................
What happened? The assembly directives
.section .fixup,"ax"
.section __ex_table,"a"
told the assembler to move the following code to the specified
sections in the ELF object file. So the instructions
3: movl $-14,%eax
xorb %dl,%dl
jmp 2b
ended up in the .fixup section of the object file and the addresses
.long 1b,3b
ended up in the __ex_table section of the object file. 1b and 3b
are local labels. The local label 1b (1b stands for next label 1
backward) is the address of the instruction that might fault, i.e.
in our case the address of the label 1 is c017e7a5:
the original assembly code: > 1: movb (%ebx),%dl
and linked in vmlinux : > c017e7a5 <do_con_write+e1> movb (%ebx),%dl
The local label 3 (backwards again) is the address of the code to handle
the fault, in our case the actual value is c0199ff5:
the original assembly code: > 3: movl $-14,%eax
and linked in vmlinux : > c0199ff5 <.fixup+10b5> movl $0xfffffff2,%eax
The assembly code
> .section __ex_table,"a"
> .align 4
> .long 1b,3b
becomes the value pair
> c01aa7d4 c017c2f6 c0199fe9 c017e7a5 c0199ff5 ................
^this is ^this is
1b 3b
c017e7a5,c0199ff5 in the exception table of the kernel.
So, what actually happens if a fault from kernel mode with no suitable
vma occurs?
1.) access to invalid address:
> c017e7a5 <do_con_write+e1> movb (%ebx),%dl
2.) MMU generates exception
3.) CPU calls do_page_fault
4.) do page fault calls search_exception_table (regs->eip == c017e7a5);
5.) search_exception_table looks up the address c017e7a5 in the
exception table (i.e. the contents of the ELF section __ex_table)
and returns the address of the associated fault handle code c0199ff5.
6.) do_page_fault modifies its own return address to point to the fault
handle code and returns.
7.) execution continues in the fault handling code.
8.) 8a) EAX becomes -EFAULT (== -14)
8b) DL becomes zero (the value we "read" from user space)
8c) execution continues at local label 2 (address of the
instruction immediately after the faulting user access).
The steps 8a to 8c in a certain way emulate the faulting instruction.
That's it, mostly. If you look at our example, you might ask why
we set EAX to -EFAULT in the exception handler code. Well, the
get_user macro actually returns a value: 0, if the user access was
successful, -EFAULT on failure. Our original code did not test this
return value, however the inline assembly code in get_user tries to
return -EFAULT. GCC selected EAX to return this value.
NOTE:
Due to the way that the exception table is built and needs to be ordered,
only use exceptions for code in the .text section. Any other section
will cause the exception table to not be sorted correctly, and the
exceptions will fail.
Things changed when 64-bit support was added to x86 Linux. Rather than
double the size of the exception table by expanding the two entries
from 32-bits to 64 bits, a clever trick was used to store addresses
as relative offsets from the table itself. The assembly code changed
from:
.long 1b,3b
to:
.long (from) - .
.long (to) - .
and the C-code that uses these values converts back to absolute addresses
like this:
ex_insn_addr(const struct exception_table_entry *x)
{
return (unsigned long)&x->insn + x->insn;
}
In v4.6 the exception table entry was expanded with a new field "handler".
This is also 32-bits wide and contains a third relative function
pointer which points to one of:
1) int ex_handler_default(const struct exception_table_entry *fixup)
This is legacy case that just jumps to the fixup code
2) int ex_handler_fault(const struct exception_table_entry *fixup)
This case provides the fault number of the trap that occurred at
entry->insn. It is used to distinguish page faults from machine
check.
3) int ex_handler_ext(const struct exception_table_entry *fixup)
This case is used for uaccess_err ... we need to set a flag
in the task structure. Before the handler functions existed this
case was handled by adding a large offset to the fixup to tag
it as special.
More functions can easily be added.