87 строки
3.3 KiB
C
87 строки
3.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0-only */
|
|
|
|
#ifndef _LINUX_GPIO_REGMAP_H
|
|
#define _LINUX_GPIO_REGMAP_H
|
|
|
|
struct device;
|
|
struct gpio_regmap;
|
|
struct irq_domain;
|
|
struct regmap;
|
|
|
|
#define GPIO_REGMAP_ADDR_ZERO ((unsigned int)(-1))
|
|
#define GPIO_REGMAP_ADDR(addr) ((addr) ? : GPIO_REGMAP_ADDR_ZERO)
|
|
|
|
/**
|
|
* struct gpio_regmap_config - Description of a generic regmap gpio_chip.
|
|
* @parent: The parent device
|
|
* @regmap: The regmap used to access the registers
|
|
* given, the name of the device is used
|
|
* @label: (Optional) Descriptive name for GPIO controller.
|
|
* If not given, the name of the device is used.
|
|
* @ngpio: Number of GPIOs
|
|
* @names: (Optional) Array of names for gpios
|
|
* @reg_dat_base: (Optional) (in) register base address
|
|
* @reg_set_base: (Optional) set register base address
|
|
* @reg_clr_base: (Optional) clear register base address
|
|
* @reg_dir_in_base: (Optional) in setting register base address
|
|
* @reg_dir_out_base: (Optional) out setting register base address
|
|
* @reg_stride: (Optional) May be set if the registers (of the
|
|
* same type, dat, set, etc) are not consecutive.
|
|
* @ngpio_per_reg: Number of GPIOs per register
|
|
* @irq_domain: (Optional) IRQ domain if the controller is
|
|
* interrupt-capable
|
|
* @reg_mask_xlate: (Optional) Translates base address and GPIO
|
|
* offset to a register/bitmask pair. If not
|
|
* given the default gpio_regmap_simple_xlate()
|
|
* is used.
|
|
*
|
|
* The ->reg_mask_xlate translates a given base address and GPIO offset to
|
|
* register and mask pair. The base address is one of the given register
|
|
* base addresses in this structure.
|
|
*
|
|
* Although all register base addresses are marked as optional, there are
|
|
* several rules:
|
|
* 1. if you only have @reg_dat_base set, then it is input-only
|
|
* 2. if you only have @reg_set_base set, then it is output-only
|
|
* 3. if you have either @reg_dir_in_base or @reg_dir_out_base set, then
|
|
* you have to set both @reg_dat_base and @reg_set_base
|
|
* 4. if you have @reg_set_base set, you may also set @reg_clr_base to have
|
|
* two different registers for setting and clearing the output. This is
|
|
* also valid for the output-only case.
|
|
* 5. @reg_dir_in_base and @reg_dir_out_base are exclusive; is there really
|
|
* hardware which has redundant registers?
|
|
*
|
|
* Note: All base addresses may have the special value %GPIO_REGMAP_ADDR_ZERO
|
|
* which forces the address to the value 0.
|
|
*/
|
|
struct gpio_regmap_config {
|
|
struct device *parent;
|
|
struct regmap *regmap;
|
|
|
|
const char *label;
|
|
int ngpio;
|
|
const char *const *names;
|
|
|
|
unsigned int reg_dat_base;
|
|
unsigned int reg_set_base;
|
|
unsigned int reg_clr_base;
|
|
unsigned int reg_dir_in_base;
|
|
unsigned int reg_dir_out_base;
|
|
int reg_stride;
|
|
int ngpio_per_reg;
|
|
struct irq_domain *irq_domain;
|
|
|
|
int (*reg_mask_xlate)(struct gpio_regmap *gpio, unsigned int base,
|
|
unsigned int offset, unsigned int *reg,
|
|
unsigned int *mask);
|
|
};
|
|
|
|
struct gpio_regmap *gpio_regmap_register(const struct gpio_regmap_config *config);
|
|
void gpio_regmap_unregister(struct gpio_regmap *gpio);
|
|
struct gpio_regmap *devm_gpio_regmap_register(struct device *dev,
|
|
const struct gpio_regmap_config *config);
|
|
void gpio_regmap_set_drvdata(struct gpio_regmap *gpio, void *data);
|
|
void *gpio_regmap_get_drvdata(struct gpio_regmap *gpio);
|
|
|
|
#endif /* _LINUX_GPIO_REGMAP_H */
|